Whirlpool MK1190XHB Installation guide

Whirlpool
Brand
Whirlpool
Model
MK1190XHB
Type
Installation guide

This manual is also suitable for

Whirlpool MK1190XHB is an electric built-in trim kit compatible with Whirlpool microwave models including MT1195SG, GT1196SH, and GT1195SH. It allows for the installation of a microwave oven into existing cabinetry, providing a sleek and finished appearance. The trim kit includes all necessary mounting hardware, as well as a template for precise cutout dimensions. Its versatility makes it suitable for use with various microwave oven models, offering a convenient and functional solution for seamlessly integrating a microwave into your kitchen.

Whirlpool MK1190XHB is an electric built-in trim kit compatible with Whirlpool microwave models including MT1195SG, GT1196SH, and GT1195SH. It allows for the installation of a microwave oven into existing cabinetry, providing a sleek and finished appearance. The trim kit includes all necessary mounting hardware, as well as a template for precise cutout dimensions. Its versatility makes it suitable for use with various microwave oven models, offering a convenient and functional solution for seamlessly integrating a microwave into your kitchen.

CUTOUT DIMENSIONS
Height
3" Min.
Width
Depth
Trim Kit
Bottom Duct (1)
Side Duct (1)
1” Screws
(4 Req’d 2 Extra)
1/2” Screws
(11 Req’d 2 Extra)
Anti-Tip
Bracket (1)
Bottom
Bracket (1)
Upper Duct (1)
Template (1)
27
”
30
”
Height 16
3
/4
”
Width
25
1
/2
”
25
1
/2
”
(min.),
28
1
/2
”
(max.)
Depth
21
”
with flush mount receptacle.
(min.)
(22
3
/4
”
if non-flush receptacle is
used)
PARTS LIST
BUILT-IN TRIM KIT INSTALLATION INSTRUCTION
(KEEP FOR FURTHER REFERENCE)
FOR WHIRLPOOL TRIM-KIT MODELS: MK1197XH, MK1190XH
• FOR USE WITH WHIRLPOOL MICROWAVE OVEN MODELS : MT1195SG, GT1196SH,
GT1195SH, MT3185SH, 89990, 89999, 89998, (Y)KCMS185J, MT2210SJ
•
UL LISTED - FOR USE OVER ELECTRIC HEAT SOURCE
(INCLUDING MODELS - 27”: (Y)RBS275PD, (Y)GBS277PD, KEBI171D, (Y)KEBS177D
- 30”: (Y)RBS305PD, GBS307PD, (Y)KEBI101D, (Y)KEBS107D)
P/NO.: 3828W5U0085/8172239
1
/2" Screws (2)
Front
Rear
1
/2" Screws (2)
1
/2" Screws (2)
STEP 1
1. Disconnect the microwave oven before
proceeding with installation.
2. Remove any loose items inside the microwave
oven.
3. Fasten the bottom bracket to the bottom duct
by using two
1
/2 ” screws.
4. Install bottom duct with four
1
/2 ” screws as
shown.
WARNING
Electrical Shock Hazard
Disconnect power before installing trim kit.
Replace all panels before operating.
Failure to do so can result in death or electrical shock.
FRONT VIEW OF
MICROWAVE
STEP 2
1. Remove the one existing screw from the left side of the microwave oven.
2. Connect the side duct to upper duct as shown.
a) Insert projecting tabs of upper duct into holes of side duct.
b) Bend tabs up as shown.
NOTE: Remove any oil or dirt on surface of microwave oven before ducts are attached.
3. Peel off the backing of double sided tape.
Attach the side duct and upper duct assembly
on the microwave cabinet. Press down firmly on
ducts. Fasten duct assembly to left side of
cabinet with one existing screw.
Upper Duct
3 tabs
Side Duct
3 Holes
"a)"
"b)"
Existing 
screw (1)
STEP 4
1. Slide microwave oven part way into cabinet
opening.
(Bottom brackets must be flat to the cutout
floor to engage correctly with anti-tip brackets
as shown)
2. Plug in the microwave oven.
3. Center the microwave oven within the
cut-out opening and slide the microwave oven
in place, engaging the anti-tip brackets.
(Ensure the microwave oven is accurately
centered)
4. Drill pilot holes (use 7/64” drill or #35 drill)
through the positioning flange and then install
three 1/2” screws at the front of the bottom
duct as shown.
Bottom Duct
Anti-Tip
Bracket
Bottom Bracket
1
/2" Screw
Anti-Tip Assembly
Positioning
Flange
Cutout
Opening
1
/2" Screw
STEP 3
1. On the cutout floor, mark hole centers for the
anti-tip brackets as shown using the supplied
template. Be sure to align the center line of
template to center line of cutout floor.
2. Drill two holes for anti-tip bracket.
(use 7/64” drill or #35 drill)
3. Install anti-tip bracket onto cutout floor using
two 1/2” screws.
DIMENSIONS:
A = 4
1/
4 ”
B = 3 ”
C = 18
3/
16 ”
A
B
C
Cutout Floor
Center Line
Anti-Tip Bracket
1
/2" Screws (2)
STEP 5
1. Place the trim kit frame over the microwave oven.
Important Note : Trim kit frame orientation is
important. Orient the frame so that
louvers are sloping downward
to the front. (See Figure Detail A).
2. Make sure the trim kit is level and centered
with respect to microwave oven. Mark four
hole centers through the four mounting
holes of the trim kit.
NOTE: Center the trim kit frame equally
on all four sides.
3. Remove the trim kit and drill four pilot holes.
(use 7/64” drill or #35 drill)
4. Attach the trim kit frame by using four 1” screws.
Make sure that the orientation is correct as
stated above.
STEP 6
1. Your trim kit is now fully installed. Replace
any loose items that have been removed
from inside microwave oven.
2. Please keep this installation instruction for
future reference.
Trim Kit
Mounting
Hole
Pilot
Hole
Cutout
Opening
1" Screw
"A"
Figure Detail of "A"
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Whirlpool MK1190XHB Installation guide

Whirlpool
Brand
Whirlpool
Model
MK1190XHB
Type
Installation guide
This manual is also suitable for

Whirlpool MK1190XHB is an electric built-in trim kit compatible with Whirlpool microwave models including MT1195SG, GT1196SH, and GT1195SH. It allows for the installation of a microwave oven into existing cabinetry, providing a sleek and finished appearance. The trim kit includes all necessary mounting hardware, as well as a template for precise cutout dimensions. Its versatility makes it suitable for use with various microwave oven models, offering a convenient and functional solution for seamlessly integrating a microwave into your kitchen.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents