Audiovox CE520 Operating Instructions Manual

Brand: Audiovox

Model: CE520

Category: CD players

Type: Operating Instructions Manual

MW/AM

LOOP

ANTENNA

The AC cord to an AC outlet

SYSTEM CONNECTIONS

2. CONNECTION WITH OTHER OPTIONAL EQUIPMENT

To listen to or record audio signals from external

units through this unit.

Connect the red plug to the R jack, and the white

plug to the L jack to the AUX jack.

LISTENING TO THE CONNECTED EQUIPMENT

1. Press the FUNCTION button to AUX.

2. Play the external source.

CD SECTION

To find a previous track

Press SKIP button once to return to

the beginning of the current track.

Press SKIP button repeatedly to skip

tracks backward one by one.

To skip tracks

Press SKIP button repeatedly to skip

track(s) forward one by one.

Keep it pressed

Press it once

NOTE :

The CD player may skip if the loud speakers are situated close to the player and if high volume or bass

levels are used.

Searching for the beginning of a trackLocating a particular point in a track

CD PLAYING

1. Press the CD button.

BACKWARD

FORWARD

2. Press the OPEN/CLOSE button to open CD door. Place

a disc in the CD tray with the label face front and then

press the OPEN/CLOSE button to close CD door. The

total number of tracks will show on the display.

NOTES:

• Do not push the CD door to close it.

• CD door cannot open while power is off.

3. To start playing, press PLAY/PAUSE

button.

TO INTERRUPT PLAYBACK

Press PLAY/PAUSE button.

The indicator will light up.

To resume playback, press PLAY/PAUSE

button again.

TO STOP PLAYBACK

Press STOP button.

To move backward at high speed

Keep SKIP button pressed during play

and release at the desired point.

To move forward at high speed

Keep SKIP button pressed during play

and release at the desired point.

FORWARDBACKWARD

PARTS IDENTIFICATION

1. MODE selector (BEAT CUT/FM

MODE/DUBBING)

2. PHONES jack

3. Cassette Deck A operation buttons

PAUSE button

STOP/EJECT button

F.FWD button

REW button

PLAY button

4. Cassette Deck B operation buttons

PAUSE button

STOP/EJECT button

F.FWD button

REW button

PLAY button

REC button

5. Cassette knob cover

6. Cassette Deck A door

7. CD door

8. POWER/STANDBY button

9. CD PLAY/PAUSE button

10. / SKIP/TUNING buttons (UP/

DOWN)

11. CD STOP button

12. PRESET/REPEAT button

13. MEMORY button

14. RANDOM button

15. REMOTE SENSOR

16. STANDBY indictor

17. X-BASS indicator

18. DISPLAY window

19. TUNER button

20. CD button

21. TAPE button

22. BAND button

23. X-BASS button

24. VOLUME ( / )

25. OPEN/CLOSE button

26. Cassette Deck B door

27. FM 75 ohm antena terminal

28. AM/MW antenna socket

29. AUX IN jack

30. AC cord

31. Speaker terminals

RANDOM PLAY

This function will allow a single track or all the tracks on the disc to be played repeatedly.

TURNING ON THE UNIT

TO TURN ON THE UNIT

Press POWER button, the display will illuminate. Select the desired function and the corresponding

function indicator will show in the display.

TO TURN OFF THE UNIT

Press the POWER button to enter STANDBY. The display illumination will fade and only the clock

display will be shown.

POWER INDICATOR

While the AC cord is connected and the unit is on stand-by, power will be consumed and only the

clock display will be lit.

• Press the POWER button to turn on the unit. After a short period of time the display will show:

• Press the TAPE button. After a short period of time the display will show:

• Press the CD button. After a short period of time the display will show:

• Press the AUX button (on remote control only). After a short period of time the display will show:

• After using the unit press the POWER button until the display shows the time (at standby mode).

DISPLAY

Caution:

• Be sure the AC power cord is disconnected

and all functions are off before making con-

nections.

• To prevent electrical shock, match wide

blade of plug to wide slot, fully insert. (FOR

N. America)

1. SPEAKER CORD CONNECTION

Connect the right speaker to the R terminal, and

the left to the L terminal.

Connect the wires with the printed white lines to the

red (+) terminals and the plain-black wires to the black

(-) terminals.

WARNING:

Connecting speakers other than the speakers

supplied with the unit may damage the unit.

2. Press the PLAY/PAUSE button to start

play.

1. Press the RANDOM button, the word

"RANDOM" will appear on the display.

TIMER OPERATION (for remote control only)

The power can be turned on and off automatically at a preset time so that you can wake up to tape

music, CD, radio or AUX. Make sure the clock is set the correct before the timer setting.

TIMER SETTING - at standby mode

1. Press MODE/REMAIN button until ON/OFF is in the display.

2. Press MEM button in clock mode. Hour and minutes will flash.

3. Press TUN + buttons to set correct hour.

4. Press TUN - buttons to set the correct minutes.

5. Press MEM button to store the ON/OFF time. It will return to normal mode.

Cancel the timer function

Press the SHIFT and TIMER button until the timer indicator turn off.

SLEEP SETTING (for remote control only)

When the sleep timer is used, the power is automatically turned off after the specified time passes.

1. Press the SLEEP button while the power

is on. "SLEEP 90" lights in the display.

Note: SLEEP time can only be adjust in

TUNER, TAPE, CD and AUX modes.

2. Press SLEEP button repeatedly to select

the length of remaining time until the unit

turns off.

It changes the indicator in the following way:

The sleep timer is set and the SLEEP indica-

tor lights in the display. Let go when required

sleep time (in minutes) is shown.

To cancel the sleep timer, press the SLEEP

button once and "SLEEP" will go out in the

display.

PLAY TIMER RECORD TIMER

1. Set the time of the timer-on and timer-off.

2. Select the desired program source with

the FUNCTION.

TUNER: Select a band and station.

TAPE: Insert the cassette tape.

CD: Insert a disc.

3. Press TIMER.

TIMER appears in the display.

4. Press POWER to standby mode.

5. For cassette playback, press PLAY.

At the timer-on time, the system turns on

automatically.

The system will record a radio broadcast

at a preset time.

1. Set the time of the timer-on and timer-off.

2. Set to TUNER.

3. Select a band and station.

4. Insert the cassette tape for recording.

5. Press TIMER.

TIMER appears in the display.

6. Press POWER to standby mode.

7. Press REC (record) which also engages

PLAY.

INTRODUCTION PLAY - - at CD stop mode (for remote control only)

TO CANCEL RANDOM PLAYBACK

1. Press the STOP button to stop random

playing.

2. Press the RANDOM button to deactivate ran-

dom playback.

Press the SHIFT & INTRO button, the word "INTRO" will appear on the display.

REPEAT PLAY

This function will allow a single track or all the tracks on the disc to be played repeatedly.

TO REPEAT THE SAME TRACK

Press the REPEAT button to repeat the cur-

rent track. The "REPEAT 1" indicator light up.

TO REPEAT THE WHOLE DISC

Press the REPEAT button until the "REPEAT

ALL" indicator light up.

TO CANCEL REPEAT PLAY

Press REPEAT button until the REPEAT indicator turn off.

DURING STOP MODE

The REPEAT operations can also be set in the

stop mode. The player will start playing from

Track 1 of the currently selected disc after

PLAY/PAUSE button is pressed.

The REPEAT operations can also be set from

paused playback point. The player will start play-

ing again after PLAY/PAUSE button is

pressed.

DURING PAUSE MODE

STOPPING AND CANCELLING PROGRAMMED PLAYBACK

To stop programmed play for a moment:

• Press the PLAY/PAUSE button and "II" will be displayed.

Press this button again to resume playing.

To stop programed playback:

• Press the STOP button.

To erase the whole programme:

• Press the STOP button or select another

function.

Open the disc tray by pressing the OPEN/

CLOSE button.

Up to 20 tracks can be programmed to play in any order using this function.

PROGRAMMING PLAYBACK --- in the stop mode

repeat step 2 to 3.

5. To start playback, press the PLAY/PAUSE

button.

1. Press MEMORY button (in stop mode).

2. Press SKIP button to select the desired track.

3. Press MEMORY button again to store this track in memory.

4. To program additional tracks,

NOTE:

During programme playback, the SKIP buttons can only be used for the selected

tracks.

TO CANCEL INTRODUCTION PLAY

Press the STOP button to stop introduction play.

ADJUSTING THE SOUND

Press button

to decrease the

volume.

Press button

to increase the

volume.

Press X-BASS button

to increased the low

frequency sound level.

To adjust the volume For loud deep bass

WHEN RECORDING

Adjustments to the VOLUME control or the X-BASS control will not affect the recording.

FOR PRIVATE LISTENING

Connect a headphone (ø3.5mm stereo mini-plug) to the PHONES jack.

When the headphone is connected, speakers are automatically disconnected.

CLOCK SETTING - in standby mode

1. Press MEMORY button the Hour and

Minutes will flash.

2. Press SKIP/TUNING ( DOWN ) but-

ton to set hour.

3. Press SKIP/TUNING ( UP ) button to

set minutes.

4. Press MEMORY button to set hour and

minutes, start the clock.

Note: If a button is not pressed for 10 seconds the clock set mode will be exited automatically.

TUNER

RANDOM

INTRO

MEMORY

➊➋ ➌ ➍ ➎

POWER ON

STANDBY

TAPE

VOL

MEMORY

UPSKIP/TUNING

DOWN

UPSKIP/TUNING

DOWN

OPEN/CLOSE

MEMORY

UPSKIP/TUNING

DOWN

MEMORY

OPEN/CLOSE

UPSKIP/TUNING

DOWN

UPSKIP/TUNING

DOWN

PRESET/

PRESET/ PRESET/

3. MW/AM LOOP ANTENNA CONNECTION

Do not connect to an outside antenna.

Connect the supplied MW/AM loop antenna to

receive better MW/AM broadcast signal.

4. FM ANTENNA WIRE

Do not connect to an outside antenna.

5. POWER CORD CONNECTION

Before use, check that the rated voltage of your

unit matches your local voltage.

Connect the AC cord to an AC outlet.

The STANDBY indicator will light up and the clock

will be displayed.

TUNER

TIMER

MEMORY

123 768 10911

1. X-BASS indicator

2. CD function indicator

3. BAND FM/MW(AM) indicator

4. REPEAT mode indicators

5. PLAY / PAUSE indicators

6. MEMORY indicator

7. FM STEREO indicator

8. CD RANDOM indicator

9. TUNER function Indicator

10. INTRODUCTION indicator

11. TIMER ON/OFF indicators

12. SLEEP indicator

13. CLOCK/CD TIMING/TAPE/AUX/TUNER FRE-

QUENCY/CD TRACK/PRESET STATION

NUMBER indicators

RANDOM

1. Press the TUNER button.

TUNING INTO A STATION MANUALLY

TUNER SECTION

TAPE A OR TAPE B PLAYBACK

Use only normal (type I) tapes for playback.

TAPE SECTION

3. Press the TUNING button to

select a station.

2. Press BAND button to select the desired

band.

Fully unwind the wire antenna. Then extend

the wire antenna and place it in the position

that sounds best.

MW/AM

Connect the loop aerial (provided) to

the AM (MW) ANT. snap terminal. Set

the MW/AM loop antenna to a direc-

tion for the better reception

FOR BETTER RECEPTION

TO SEARCH FOR A STATION AUTOMATICALLY

Press the TUNING button UP or DOWN for 1 to 2 seconds, and a station is searched for

automatically. After tuning in to a station, the search stops.

The search may not stop at a station with a very weak signal.

TO RECEIVE THE FM BROADCAST IN STEREO

Set the MODE selector to FM STEREO.

When the FM stereo broadcast is received, the "STEREO" indicator show in the display.

IF THE FM STEREO BROADCAST SIGNAL IS WEAK

Set the MODE switch to FM MONO (at top of the unit).

Background noise will be reduced but the signal reproduced will be MONO. To restore stereo, set

MODE switch to FM STEREO.

SPECIFICATIONS

GENERAL

Output power: 5 W x 2 (10% THD)

Power consumption: 42 W

Power source: AC ~ 120V 60 Hz (U.S.A. and Canada)

AC ~ 220V 50 Hz (China)

AC ~ 230V 50 Hz (Europe and Hong Kong)

AC ~ 240V 50 Hz (Australia)

AC ~ 110/120V - 220/240V 50/60Hz (other countries)

Specifications subject to change without notice.

811-227191-011

RISK OF ELECTRIC SHOCK

DO NOT OPEN

The lightning flash and

arrowhead within the

triangle is a warning

sign alerting you of

"dangerous voltage"

inside the product.

WARNING: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER (OR BACK) NO USER-SERVICE-

ABLE PARTS INSIDE. REFER SERVICING

TO QUALIFIED SERVICE PERSONNEL.

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE

THIS APPLIANCE TO RAIN OR MOISTURE.

OPERATION INSTRUCTION

WARNING

The exclamation point

within the triangle is a

warning sign alerting

you of important in-

structions accompa-

nying the product.

VERTICAL CD HOME SYSTEM

To STOP DUBBING

Press the STOP/EJECT buttons of Deck A and Deck B.

Note:

Do not change the dubbing speed when dubbing is in progress.

DUBBING ---- FROM DECK A TO DECK B

Use only normal (type I) tapes for recording and playback.

2. Insert the recorded tape into

Deck A and the blank tape into

Deck B.

1. Press the TAPE button.

3. Select the NORMAL/HIGH

DUBBING switch to the re-

quired position.

4. Press the PAUSE button.6.Press the PLAY button.5. Press the RECORD button

which also engages the PLAY

button.

DECK A

DECK B

1. Press the TAPE button. 2. Press the STOP/EJECT but-

ton and insert the cassette into

the Deck A or Deck B.

3. Press the PLAY button.

DECK A DECK B

TO STOP PLAYBACK

Press the STOP/EJECT button.

TO INTERRUPT PLAYBACK

Press the PAUSE button.

To resume play, press the PAUSE button again.

TO FAST WIND OR REWIND

Press F.FWD or REW button. Press the

STOP/EJECT button to stop winding at the

desired position.

WHEN THE TAPE REACHES ITS END

During fast wind or regular play, the tape will stop

automatically when its end is reached.

WHEN BOTH DECK A AND DECK B ARE SET

THE PLAYBACK MODE

Deck A will playback, no sound will come from

Deck B.

1. Press the TAPE button. 2. Insert a cassette in each deck.

CONTINUOUS PLAYBACK --- FROM DECK A TO DECK B

As soon as the tape in Deck A reaches its end and stops, the pause mode for Deck B is released and

playback starts automatically.

3. Press the PLAY button. 4. Press the PAUSE button.

5. Press the PLAY button.

DECK BDECK BDECK A

MAINTENANCE

CLEANING CD

If the CD skips or cannot be played, the disc may need clean-

ing. Before playing,wipe the disc from the center out with a

cleaning cloth. After playing,store the disc in its case.

CLEANING THE UNIT

Do not use volatile chemicals on this unit. Clean by lightly wiping with a soft cloth.

IMPORTANT NOTE

• If an abnormal display indication or an operating problem occurs, disconnect the AC power

cord. Wait at least 5 seconds, then reconnect the AC power cord.

CLEANING THE TAPE HEADS

To maintain optimum sound quality, clean the playback/record

heads (a), erase head (b), pinch rollers (c), and capstans (d)

regularly (every 10 hours of use), using a cotton swab lightly

moistened with cleaning fluid or denatured alcohol.

TROUBLE SHOOTING GUIDE

PROBLEMS

No power supply.

The cassette cannot be inserted.

The tape gets caught in the tape transport

mechanism.

Tape running is unstable.

There is excessive noise during tape playback.

The REC cannot be pressed.

No recording or poor recording.

The previous recording cannot be erased.

CD play does not begin.

The CD produces no sound.

The CD sound jumps.

ITEMS TO CHECK

• Is the power cord unplugged or loose?

• Is the cassette facing the wrong direction

when you try to insert it?

• Is the pinchroller or capstan dirty?

• Is there excessive slack in the tape?

• Is the head dirty?

• Is a cassette inserted?

• Is the erase prevention tab on the cassette

broken off?

• Are the heads dirty?

• Is the erase head dirty?

• Is the CD upside down?

• Is the CD or lens excessively dirty?

• Is the disc holder closed properly?

• Is the function selector set to CD?

• Is the pause mode on?

• Is there condensation inside the unit?

• Is the lens or CD excessively dirty?

• Is the unit subject to excessive vibration?

• Are there any bad scratches on the CD?

PRECAUTIONS

WARNING

ON PLACEMENT

• Do not use the unit in places which are

extremely hot, cold, dusty, or humid.

• Place the unit on a flat, even surface.

• Do not restrict the air flow through the

ventilation slots by placing the unit on the

soft furnishings, by covering the unit with

a cloth or by placing the unit on a carpet.

ON SAFETY

• When connecting and disconnecting the

AC cord, grip the plug and not the cord

itself. Pulling the cord may damage it and

create hazard.

• Disconnect from the AC mains when the

unit is not going to be used for some time.

ON AC VOLTAGE

• Before use, check that the rated volt-

age of your unit matches your local volt-

age.

FCC INFORMATION

This device complies with part 15 of FCC

Rules. Operations are subject to the fol-

lowing two conditions:

(1)This device may not cause harmful inter-

ference, and

(2)This device must accept any interference

received, including interference that may

cause undesirable operations.

ON CONDENSATION

• When left in a heated room where it is warm

and damp, water droplets or condensa-

tion may form inside the CD player.

• When there is condensation inside the unit,

the unit may not function normally.

• Let it stand in a heated room for 3 hours to

allow the condensation to dry out.

VENTILATION WARNING

• The normal ventilation of the product shall

not be impeded for intended use.

Should any trouble occur, disconnect the AC power cord and refer servicing to

qualified personnel.

RECORDING ---- DECK B ONLY

RECORDING FROM THE CD PLAYER

4. Press the PLAY/PAUSE button of the

CD player.

3. Press the RECORD button which also

engages the PLAY button.

DECK B

2. Insert a tape into

the cassette com-

partment.

1. Press the CD button.

RECORDING ---- DECK B ONLY

Use only normal (type I) tapes for recording.

RECORDING FROM THE BUILT-IN TUNER

Note:

If a whistle is heard (beat), it may be reduced by sliding the BEAT CUT switch on the left top of the unit

to BEAT CUT 2 position.

2. Insert a tape into the cassette

compartment.

3. Press the RECORD button

which also engages the

PLAY button.

1. Press the TUNER button

and tune into a desired

station.

DECK B

TO ERASE A RECORDED TAPE

1. Press the FUNCTION button to TAPE.

2. Insert a tape with the side you want to erase

facing you.

3. Press the RECORD button to start erasing.

TO STOP RECORDING

Press the STOP/EJECT button of Deck B.

TO INTERRUPT RECORDING

Press the PAUSE button of Deck B.

To resume recording, press the PAUSE button again.

TUNER

TIMER

MEMORY

REMOTE CONTROL

1. POWER/STANDBY button

2. CD button

3. TAPE button

4. STOP button

5. SKIP/TUNING buttons

6. MEM /INTRO (introduction) button

7. MODE/REMAIN button

8. SLEEP/TIMER button

9. VOLUME +/- buttons

10. SHIFT button

11. BAND/RANDOM button

12. X-BASS button

13. PLAY/PAUSE button

14. REPEAT/PRESET button

15. TUNER button

16. AUX button

DECK B

This sid

you wan

to recor

TAPE

Tape to be played

Tape to be record

DECK B

This sid

you wan

to recor

TAPE

DECK BDECK A

Played

first

DECK BDECK A

TAPE

TUNER

BAND

USING THE REMOTE CONTROL CORRECTLY

• Point the Remote Control at the REMOTE SENSOR located on the unit.

• When there is a strong ambient light source, the performance of the infrared REMOTE SENSOR

may be degraded, causing unreliable operation.

• The recommended effective distance for remote operation is about 6 metres (19 feet).

TO CHANGE REMOTE BATTERY

BATTERY REPLACEMENT

When batteries become weak, the operating distance of the Remote Control is greatly reduced and

you will need to replace the batteries.

NOTE:

If the Remote Control is not to be used for a long time, remove the battery to avoid damage caused by

battery leakage corrosion.

TUNER BAND

TUNER

MEMORY MEMORY

BAND

UPSKIP/TUNING

DOWN

PRESETTING STATION

The unit can store stations (FM 16 stations and AM 16 stations).They can be tuned in to by selecting

their preset numbers. It is possible to store stations of any band in order of your choice.

Manual memory presetting

This function allows you to manually preset stations into any desired memory.

1. Press the TUNER button. 2. Press the BAND button to select the desired

band and press SKIP button tune a

station.

3. Press the MEMORY button until the

memory indicator blinks.

4. Press the MEMORY button to record.

Then, repeat steps 2 to 4.

3. Press the PRESET buttons

to select the preset number.

TUNING INTO A PRESET STATION

NOTE

The contents (preset channel number, frequency and frequency band) which have been stored

in memory will appear in the display in numerical order, irrespective of the frequency bands.

1. Press the TUNER button .

2. Press the BAND button to

select a band.

UPSKIP/TUNING

DOWN

CLASS 1 LASER PRODUCT

APPAREIL Á LASER DE CLASSE 1

PRODUIT LASER DE CLASSE 1

CAUTION

INVISIBLE LASER RADIATION

WHEN OPEN AND INTERLOCKS

DEFEATED.

AVOID EXPOSURE TO BEAM

CLASS 1 LASER PRODUCT

This product contains a low power laser device.

1. Open the battery door. 2. Insert one CR2025 (3V)

size battery.

ATTENTION

Take out the PVC sheet before

operating the

Remote Control.

PRESET/

TUNER

Page is loading ...

Audiovox CE520 Operating Instructions Manual

Brand: Audiovox

Model: CE520

Category: CD players

Type: Operating Instructions Manual

Download PDF

report

in other languages

français: Audiovox CE520
español: Audiovox CE520

Audiovox CE520 Operating Instructions Manual

Audiovox CE520 Operating Instructions Manual

in other languages

Related papers

Other documents