Petsafe HKA11-11927 Owner's manual

Brand: Petsafe

Model: HKA11-11927

Type: Owner's manual

PetSafe

Grandview Dog Kennel

™

Roof

Assembly Instructions

Instrucciones de armado

Please read this entire guide before assembly.

Sírvase leer esta guía completa antes de comenzar el armado.

2 1-888-632-4453

Thank you for choosing PetSafe

. The relationship you have with your pet is the focus

of everything we do. If you have questions about, or are dissatisﬁ ed with, any of our

products, please contact the Customer Care Center at 1-888-632-4453 or visit our

website at www.petsafe.net.

Table of Contents

Components ................................................................................................................................... 3

Tools Needed .................................................................................................................................. 3

Check Kennel Alignment ................................................................................................................. 4

Assemble Center Connector, Center Brace and 28.5 inch (72.3cm) Tubing ....................................... 4

Install Center Roof Assembly to Kennel ........................................................................................... 4

Connect Upright Tubing with Clamp, Elbows and Swedged Tubing .................................................. 5

Fit the Tarp on the Roof Frame ........................................................................................................ 6

Secure the Tarp to the Kennel .......................................................................................................... 6

Caution ......................................................................................................................................... 7

Terms of Use and Limitation of Liability ......................................................................................... 7

Español ......................................................................................................................................... 8

www.petsafe.net 3

Components

Elbow

2 pcs.

Center Connector

Center Brace Tubing

2 pcs.

28.5 inch (72.3 cm) Tubing

2 pcs.

Swedged Tubing

2 pcs.

Upright Tubing with Clamp

2 pcs.

Assembly Instructions

Ta r p

Ball Bungee Cord

4 pcs.

Cable Ties

18 pcs.

afe

Grandview

Dog Kennel

™

Roof

Assem

Ins

ions

ucciones de

ensam

ado

guide

fore

sembly

vor

compl

men

est

Tools Needed

½ inch (13mm) Wrench•

Wire Cutters•

Phillips Screwdriver•

Measuring Tape•

Roof assembles easily in less than one hour.

For faster and easier assembly, get a friend to help.

4 1-888-632-4453

Check Kennel Alignment

For the best roof ﬁ t, the kennel should be squared, which means that each kennel corner is at a 90

degree angle.

Using the measuring tape, measure the kennel diagonally from corner to corner. If your measurement 1.

is less than or equal to one half inch (13mm), your kennel is square.

If your measurements exceed one half inch, adjust the kennel so that each corner is close to a 90 2.

degree angle. Measure the kennel again and continue to make adjustments until the kennel is square.

Assemble Center Connector, Center

Brace and 28.5 inch (72.3cm) Tubing

Gather Center Connector, (2) Center Brace 1.

tubes and (2) 28.5 inch (72.3cm) tubes.

On the ground, insert the (2) center brace 2.

tubes on the angled sides of the center

connector. The welded plate at each end of

the center brace tubes should face down.

Insert the (2) straight tubes on the straight 3.

sides of the center connector.

Install Center Roof Assembly to Kennel

Turn around the top clamp on each 10 foot 1.

(3.05m) side of the kennel so that the screw

head faces outside and the bolt and nut faces

the inside. Leave the connection loose.

Take the center roof assembly built in Step 2.

2 and place the center brace tubes on top

of the loosened center clamps on top of the

kennel (3A).

Step

www.petsafe.net 5

On one side of the kennel, unscrew the nut 3.

on the clamp and insert the bolt into the

oval hole on the welded plate (3B). Loosely

re-attach the nut.

Repeat Step 3 on the opposite side. Once 4.

both sides are attached, tighten the nuts

on each side. The top of the clamps should

be ﬂ ush against the bottom of the top

kennel rails.

Connect Upright Tubing with Clamp,

Elbows and Swedged Tubing

Gather (2) Upright Tubes with Clamps, (2) 1.

Elbows and (2) Swedged Tubes.

Start on the outside of the kennel at either 2.

the gate panel or rear panel. Take one

upright tube with clamp and, holding it at an

angle, slide the clamp onto the center of the

top rail of the panel (4A). The hole on the

clamp must be on the outside of the kennel.

Rotate the clamp so that the tube is vertical

and the clamp ﬁ ts securely on the top rail

(4B). Loosely tighten the clamp in place

with the screw and repeat this step on the

opposite side of the kennel.

Insert one elbow into the open end of one 3.

of the swedged tubes so that the arrow is

pointing up (4C). Move to the inside of the

kennel and ﬁ t the swedged end of the tube

into the open end of one of the 28.5 inch

(72.3cm) tubes. Insert the other end of the

elbow into the upright tube with clamp.

Repeat Step 3 on the opposite side. Once 4.

the roof frame is assembled, check that

both upright tube clamps are centered on

the gate panel and rear panel of the kennel

(4D). Tighten the clamps using a Phillips

screwdriver.

4A 4B

Step

6 1-888-632-4453

Fit the Tarp on the Roof Frame

Gather the tarp.1.

Unfold the tarp and turn it right side up.2.

Start on the inside of the kennel. Place the tarp over the roof frame 3.

on one end of the kennel. Fit the grommet located at the peak

of the SunBlock

™

panel onto the plastic pin on the elbow (5A).

Repeat this step on the opposite side and ensure that the grommets

properly ﬁ t on the elbow pins.

Drape the sides of the tarp on the outside of the kennel side panels.4.

Secure the Tarp to the Kennel

Gather (4) Bungee Balls and (18) Cable Ties.1.

Attach one bungee ball to each of the four 2.

sides of the kennel at the corners. Fit the

bungee balls through the grommets on the

tarp and around the kennel side rail (6A).

Attach the sides of the tarp to the kennel 3.

using (8) cable ties. Loosely attach each

cable tie through a tarp grommet and

around the wire mesh. Once the cable ties

are in place, tighten them and snip off any

excess using the wire cutters.

Secure the SunBlock4.

™

panels on each end

of the roof to the top rail of the kennel using

(6) cable ties. When attaching the cable tie

to the center grommet of the SunBlock

™

each end of the kennel, be sure to insert the

cable tie through the hole on the upright

tube with clamp. Tighten the cable ties until

you put tension on the SunBlock

™

panel.

The bottom of the SunBlock

™

panel is not

designed to touch the top of the kennel rail

(6B). Save any remaining cable ties in a safe

place for future use.

Important: Tarp is not designed to withstand the weight of

snow. Remove cover in winter. Kennel anchors are strongly

recommended. PetSafe

Anchor Kit sold separately.

Step

www.petsafe.net 7

Caution

While this accessory product accompanies a solid barrier, Radio Systems

Corporation CANNOT guarantee

that the system will, in all cases, keep a pet within the established boundary. Not all pets can be trained for

containment. Therefore, if you have reason to believe that your pet may pose a danger to others or harm himself

if he is not kept from exiting the product, you should NOT rely solely upon the PetSafe

dog kennel to contain

your pet. Radio Systems

Corporation shall NOT be liable for any property damage, economic loss or any

consequential damages sustained as a result of any animal exiting the system. If you are unsure whether this is

appropriate for your pet, please consult your veterinarian or certiﬁ ed trainer. This product is designed for use

with pets only.

This Product is offered to you conditioned upon your acceptance without modiﬁ cation of the terms,

conditions and notices contained herein. Usage of this Product implies acceptance of all such terms,

conditions, and notices.

Proper Use 2.

This Product is designed for use with pets where training is desired. The speciﬁ c temperament of your pet

may not work with this Product. If you are unsure whether this is appropriate for your pet, please consult your

veterinarian or certiﬁ ed trainer.

No Unlawful or Prohibited Use 3.

This Product is designed for use with pets only. This pet training device is not intended to harm, injure or

provoke. Using this Product in a way that is not intended could result in violation of Federal, State or local laws.

Limitation of Liability 4.

In no event shall Radio Systems

Corporation be liable for any direct, indirect, punitive, incidental, special or

consequential damages, or any damages whatsoever arising out of or connected with the use or misuse of this

Product. Buyer assumes all risks and liability from the use of this Product.

Modification of Terms and Conditions 5.

Radio Systems

Corporation reserves the right to change the terms, conditions and notices under which this

Product is offered.

Page is loading ...

www.petsafe.net 15

Radio Systems

Corporation

10427 Electric Avenue

Knoxville, TN 37932

1-888-632-4453

www.petsafe.net

400-1104-15

Corporation

Petsafe HKA11-11927 Owner's manual

Brand: Petsafe

Model: HKA11-11927

Type: Owner's manual

Download PDF

report

in other languages

español: Petsafe HKA11-11927 El manual del propietario

Petsafe HKA11-11927 Owner's manual

Petsafe HKA11-11927 Owner's manual

in other languages

Related papers

Other documents