Bauknecht WAT UNIQ 642 AAA User guide

WAT UNIQ 642 AAA
Bauknecht
Brand
Bauknecht
Model
WAT UNIQ 642 AAA
Category
Washing machines
Type
User guide
GB
5019 400 00005
Programme
Tempera-
ture
Care
Labels
Max.
Load
kg
Type of wash / Notes
- for temperature selection, respect the manufacturer's recommendations on the care
label
Detergents and additives Special options Finish
on
time
Fertig
in
Spin
Pre-
wash
Main
wash
Softener Pre-
wash
Vor-
wäsche
Intensive
rinse
Intensiv-
spülen
Tumble
fresh
Auf-
lockern
Rapid
Kurz
15 °
Green
&
clean
Spin
Schleu-
dern
Max
spin
speed
rpm
Mixed Mix
Cold - 60°C 3.0
Lightly to normally soiled robust laundry made of cotton, linen, artificial fibres and their
blends. Effective one-hour programme. Make sure to wash only similar colours together in one
wash load.
– Yes
i
–
i i
–
i i i
max.
Fabrics
Cotton Koch / Bunt
Cold - 95°C 6.0
Normally to heavily soiled bed linen, table linen and underwear, towels, shirts etc.
made of cotton and linen.
i
Yes
i i i i i i i i
max.
Synthetics Pflegeleicht
Cold - 60°C 3.0
Normally soiled garments made of artificial fibres (like polyester, polyacryle, viscose
etc.) or their blends with cotton.
i
Yes
i i i i i i i i
max.
Delicates Fein
Cold - 40°C 1.5
Curtains and delicate clothing, dresses, skirts, shirts and blouses.
i
Yes
i i
–
i
–
i i i
1000
1)
Wool /
Handwash
Wolle/Hand
Cold - 40°C 1.0
Woollens, labelled with the Woolmark and identified as machine washable, as well as
textiles made of silk, linen, wool and viscose marked as handwashable. This programme
is tested and approved by The Woolmark Company for machine- and handwashable wool. Select
spin speed according to the manufacturer‘s recommendation on the care label.
– Yes
i
– –
i
–
i i i
1000
1)
Jeans Jeans
Cold - 60°C 4.0
Normally soiled cotton jeanswear and garments made of robust jeanslike material such
as trousers and jackets.
i
Yes
i i i i i i i i
1000
1)
Colours
White Weiße Wäsche
Cold - 60°C 6.0
Normally to heavily soiled and robust white cotton laundry.
Save energy by selecting a lower wash temperature and adding an oxygen-based bleach product,
in addition to your detergent.
– Yes
i
–
i i
–
i i i
max.
Light Colours Helle Farben
Cold - 60°C 4.0
White and pastel shaded garments made of delicate fabrics. Gentle wash programme to
avoid graying or yellowing of your laundry. Use heavy duty detergent, if necessary also stain removers or
bleaches on oxygen basis. Do not use liquid detergent.
i
Yes
i i i i i i i i
1000
1)
Dark
Schwarz &
Dunkel
Cold - 60°C 4.0
Black and dark garments made of cotton, cotton blends and polyester.
Special programme to reduce colour fading and local discolouration. Prefer to use a liquid
detergent for dark garments with this programme.
i
Yes
i i i i i i i i
max.
Eco
Super Silent Super Silent
Cold - 60°C 6.0
Robust laundry made of cotton or linen. Programme optimized for silent washing and spinning, for
example during the night. If you want to avoid completely noise of spinning at night, set spin speed to “0”
and start spin programme in the morning, or define programme start with “Finish on time” accordingly.
– Yes
i
–
i i
–
i i i
1000
1)
Aqua Eco AquaEco
Cold - 40°C 2.5
Lightly soiled laundry made of synthetic fibres, or synthetics mixed with cotton
garments. Saving programme with very low water consumption. Use liquid detergent and the
lowest recommended amount for 3 kg laundry. Do not use softener.
– Yes – – –
i
–
i i i
max.
Speed 15 Kurz 15´
Cold - 30°C 3.0
Refreshes briefly worn clothing made of cotton, artificial fibers and blends with cotton.
Use lowest recommended detergent amount.
– Yes
i
– –
i
–
i i i
max.
Eco Cotton
Baumwolle
Eco
40 - 60°C 6.0
Normally soiled cotton laundry. Most favourable programme in terms of combined water and
energy consumption for washing cotton laundry.
- Reference programme for the Energy Label.
– Yes
i
–
i i
– –
i i
max.
Rinse & Spin
Spülen &
Schleudern
– – 6.0
Rinse and intensive spin programme.
Same as the last rinse and the final spin in the “Cotton” programme.
– –
i
–
i i
– –
i i
max.
A. Programme selector
B. Option buttons
C. “Favourite” button
D. “Temperature” button
E. “Finish on time” button
F. “Spin” button
G. “Start” button
H. “Reset/Drain” button
I. Display
Bauknecht is a registered trademark.
J. Programme sequence indicator
K. “Lid open” indication
L. “Child lock” indication
Your washing machine is equipped with
automatic safety functions which detect and
diagnose faults at an early stage and react
appropriately, e.g.:
M. “Water tap closed” indication
N. “Clean pump” indication
O. “Service” indication
PROGRAMME CHART
The Wool / Handwash cycles of this machine have been tested and approved by The Woolmark Company for
the washing of Woolmark garments labelled as “machine wash” or “hand wash”provided that the garments are
washed according to the instructions on the garment label and those issued in this programme chart.
M0703
Pflege-
leicht
Wolle/Hand
Koch / Bunt
Jeans
Fein
Mix
Weiße Wäsche
Helle Farben
Schwarz
&
Dunkel
Spülen & Schleudern
Löschen/
Abpumpen
Vor-
wäsche
Intensiv-
spülen
Auf-
lockern
15° Green
& Clean
Schleu-
dern
Tempe-
ratur
Fertig in
Kinder-
sicherung
Start
Kurz
Ihre Pro-
gramme
Baumwolle Eco
Aqua Eco
Kurz 15’
Super
Silent
A
B
H
FE
G
D
J
I
K
i: optional / Yes : dosing required
1)
For improved garment care, spin speed is restricted in these programmes.
Active only for models with “Soil level” option.
L
M
C
N
O
B
B
5019 400 00005
CONSUMPTION DATA
Bauknecht is a registered trademark.
Add detergent as indicated on the front page and as
described in the chapter “Detergent and Additives” in your
Instructions for Use.
1. Turn the programme selector to the desired programme.
The indication next to the “Start” button blinks.
2. The temperature and spin speed indicated on the
display can be altered by pressing the “Temperature”
button or the “Spin” button.
ADD DETERGENTS, CLOSE THE LID AND
SELECT THE PROGRAMME
• The washing machine will start to tumble the laundry
periodically after programme end.
• The light of the “Tumble fresh” button will blink while
this function is active, and the display will show an
animation.
• The periodic tumbling will last up to approximately 12
hours after the end of your wash programme, and you
can stop it at any time by pressing the “Tumble fresh”
button. It will last a while until you can open the door.
• After the “tumble fresh” period has run out, the display
indicates “End”
“Rapid” button
• Enables quicker washing by shortening the programme
duration.
• Recommendable for small loads or only lightly soiled
laundry.
“15° Green & Clean” button
• Saves energy used for water heating while maintaining a
good wash result.
• Supports colour maintenance when washing coloured
laundry.
• Recommendable for lightly soiled laundry without stains.
• Make sure that your detergent is suitable for cold wash
temperatures (15 or 20 °C).
• Not selectable for Cotton 70 - 95°C.
“Spin” button
• Every programme has a predefined spin speed.
• Press the button to set another spin speed.
• If spin speed “0” is selected, the final spinning is
cancelled, and the water is drained out only. However,
intermediate spin peaks remain during the rinse phase.
SELECT ANY DESIRED OPTION
When the combination of programme and additional
option(s) is not possible, the indication lights switch off
automatically. Unsuitable combinations of options are
deselected automatically.
“Prewash” button
• Only for heavily soiled loads (for example sand, granular
dirt) sensible. Increases the cycle time by approximately
15 min.
• Do not use liquid detergent for the main wash when
activating the Prewash option.
“Intensive rinse” button
• More water is added and rinse cycle is prolonged.
• This option is particularly suitable for areas with very
soft water, washing baby linen and helping people with
allergies.
“Tumble fresh” button
• Select this option if you cannot unload the laundry soon
after programme end, or if you tend to forget the
laundry in your washing machine. It will help to keep
your laundry fresh.
Consumption values were measured in normalized conditions in compliance with standard IEC/EN 60 456. Consumption data in the home may vary with
respect to the values in the table in relation to the water supply pressure and temperature, the load and the type of wash.Water and energy consumption refer
to the default setting of the programmes; selecting special options or modifying spin speed or temperature will change the consumption data.
The programme duration may differ from the values indicated above as it depends on the operation conditions applicable at that time (see also
“Troubleshooting Guide” in your Instructions for Use).
* To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out.
** Standard Cotton programme and basis for Energy Label
Programme
Temperature
(°C)
Load
(kg)
Water
(l)
Energy
without
“Rapid”
(kWh)
ApproxProgrammeDuration (hours : minutes)
without “Rapid” with “Rapid”
Mixed 40 3.0 45 0.43 1:00
–
Cotton 95 6.0 55* 1.85 2:05
1:55
Cotton 60 6.0 48 1.02 2:30
1:45
Cotton 40 6.0 48 0.60 2:30
1:30
Synthetics 60 3.0 54* 0.85 1:55
1:14
Synthetics 40 3.0 50 0.50 1:40
0:59
Delicates 40 1.5 50 0.55 0:45
–
Wool / Handwash 40 1.0 40 0.55 0:35
–
Jeans 40 4.0 41 0.58 1:30
1:10
White 40 6.0 48 0.65 2:45
–
Light colours 40 4.0 67 0.50 1:20
1:00
Dark 40 4.0 41 0.58 1:40
1:10
Super Silent 60 6.0 48 0.78 4:00
–
Aqua Eco 40 2.5 19 0.43 1:00
–
Speed15 30 3.0 30 0.15 0:15
–
Eco Cotton ** 60 6.0 48 0.67 3:30
–
Eco Cotton ** 60 3.0 34 0.56 2:30
–
Eco Cotton 40 6.0 48 0.61 3:15
–
Eco Cotton ** 40 3.0 34 0.47 2:30
–
“DOOR OPEN” INDICATION
Before starting and after end of a programme, the lamp
lights to show the the lid can be opened. As long as a wash
programme is running, the lid remains locked and must on
no account be forced open. In case you have an urgent need
to open it during a running programme, refer to “Cancel a
running programme before the end”.
PROGRAMME START
Open the tap and press the “Start”button. The blinking
“Start” button light becomes constant. The „Door open“
indication gets off, and the wash symbol lights to indicate that
the programme is in process. In some phases, the remaining
programme time is newly calculated – if this is the case,
the „6th sense“ indication on the display will fade, and the
remaining programme time is replaced by an animation.
PROGRAMME END
• The symbols of the programme sequence indicator are
dark, and the “Door open” indication lights up.
1. Turn the programme selector to the “Off/O” position.
2. Close the water tap.
3. Open lid and drum and unload the machine.
4. Leave the lid open to allow the inside of the machine to
dry.
CHANGE PROGRAMME AND/OR OPTIONS
AFTER PROGRAMME START
1. Press the “Start” button to pause the programme. The
light blinks.
2. Select the new programme, temperature, any options
and another spin speed if you want.
3. Press the “Start”button again. The new programme
continues at the same position where the previous
programme was interrupted. Do not add detergent for
this programme.
CANCEL A RUNNING PROGRAMME BEFORE
THE END
The “Reset/Drain” button cancels a programme before
the end.
• Press the “Reset/Drain” button for at least 3 seconds.
The water is drained out; it may last a while until you can
open the lid.
FINISH ON TIME
With this function you can postpone your programme to
complete at a later time: press the button to select in how
many hours the programme shall be finished. Thus, it allows
you to have your laundry ready at a particular time and to
profit from more favourable energy rates during the night,
for example.
• Do not use liquid detergent when activating this function.
• The time until the “Cycle end” can be selected in full
hour time segments (1 to 24 h). When you press the
button, the shortest possible time will be displayed; keep
on pressing the button to loop through all the available
times. To remove it again, keep on pressing the button
until you see the value “0:00”.
• When you have selected the desired time until the
“Cycle end”, press “Start” - the countdown will begin.
• During the countdown, you can still modify the
programme setting (select or deselect options, change
spin speed etc.). If the modifications prolong the
programme duration so that it overruns the originally
set time until the “Cycle end”, the programme will start
immediately.
• Sometimes the programme may finish before the
selected time until the “Cycle end” has expired (e.g.
for small loads). In this case, the washing machine will
tumble the laundry regularly to keep it fresh, until the
selected “Cycle end” time has expired. During tumbling,
the display will show an animation. The tumbling phase
can be stopped at any time either by pressing any button
or by rotating the programme selector; the animation
will stop and the door will unlock in about 1 minute as
indicated on the display.
FAILURE INDICATIONS
In case of any failures or irregularities, consult the
“Troubleshooting Guide” in your Instructions for Use.
“Service”
Lighting up of the “Service” indication can be caused
by a fault in an electrical component. Refer to the
“Troubleshooting Guide” in your “Instructions for Use”; if
the fault persists, contact our After Sales Service.
“Water tap closed”
The appliance has no or insufficient water supply. Open
the water tap: if the indications still lights up, refer to the
“Troubleshooting Guide” in the Instructions for Use.
“Clean pump”
Waste water is not pumped out. Check whether the drain
hose is kinked or the filter must be cleaned: in the latter case
refer to the Instructions for Use (“Removing the Filter”).
SAVE YOUR FAVOURITE PROGRAMMES
If there is a programme setting which you use frequently, the
appliance offers the possibility to save one setting for each
programme so that it can be used again by just pushing one
button.
• Select the desired programme, temperature, spin speed
and option(s), push and hold the “Favourite” button
for at least 3 seconds. The lamp next to “Favourite”
shortly flashes and then lights up - the programme
settings is saved.
Next time you want to use your individual programme
settings, select the programme, push the “Favourite”
button and start by pushing “Start”.
If you want to replace the saved programme setting by
another one:
• Select programme temperature, spin speed and options
as desired and then press and hold the “Favourites”
button for at least 3 seconds.The previously saved
programme setting will be replaced by the new one.
CHILD LOCK
You can lock the buttons of the control panel against
improper use (e.g. by children).
• Press the temperature and spin speed button
simultaneously and hold them for at least 3 seconds. The
key symbol on the display lights up.
• To unlock the buttons again: proceed in the same way.
  • Page 1 1
  • Page 2 2

Bauknecht WAT UNIQ 642 AAA User guide

WAT UNIQ 642 AAA
Bauknecht
Brand
Bauknecht
Model
WAT UNIQ 642 AAA
Category
Washing machines
Type
User guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents