Panasonic sc pt 70 Owner's manual

Brand: Panasonic

Model: sc pt 70

Category: Home cinema systems

Type: Owner's manual

This manual is also suitable for

[EB]

RQTX1019-B

Operating Instructions

DVD Home Theater Sound System

Model No.SC-PT70

until

2009/09/08

P7–9

QUICK START GUIDEQUICK START GUIDEQUICK START GUIDE

Dear customer

Thank you for purchasing this product. For optimum performance and safety, please read these instructions carefully.

Before connecting, operating or adjusting this product, please read the instructions completely.

Please keep this manual for future reference.

The illustrations shown may differ from your unit.

Model number suffix “EB” denotes UK model.

Region number

The player plays DVD-Video marked with labels containing the region number “2” or “ALL”.

Example:

2 ALL

The illustration shows SC-PT70.

Obrázek představuje model SC-PT70.

SC-PT70EB-RQTX1019-B_eng.book Page 1 Thursday, August 13, 2009 5:07 PM

RQTX1019

Caution for AC Mains Lead

For your safety, please read the following text carefully.

This appliance is supplied with a moulded three pin mains

plug for your safety and convenience.

A 5-ampere fuse is fitted in this plug.

Should the fuse need to be replaced please ensure that the

replacement fuse has a rating of 5-ampere and that it is

approved by ASTA or BSI to BS1362.

Check for the ASTA mark

or the BSI mark

on the

body of the fuse.

If the plug contains a removable fuse cover you must

ensure that it is refitted when the fuse is replaced.

If you lose the fuse cover the plug must not be used until a

replacement cover is obtained.

A replacement fuse cover can be purchased from your

local dealer.

If a new plug is to be fitted please observe the wiring code

as stated below.

If in any doubt please consult a qualified electrician.

IMPORTANT

The wires in this mains lead are coloured in accordance

with the following code:

Blue: Neutral, Brown: Live.

As these colours may not correspond with the coloured

markings identifying the terminals in your plug, proceed as

follows:

The wire which is coloured Blue must be connected to the

terminal which is marked with the letter N or coloured Black

or Blue.

The wire which is coloured Brown must be connected to

the terminal which is marked with the letter L or coloured

Brown or Red.

WARNING: DO NOT CONNECT EITHER WIRE TO

THE EARTH TERMINAL WHICH IS MARKED WITH

THE LETTER E, BY THE EARTH SYMBOL

COLOURED GREEN OR GREEN/YELLOW.

THIS PLUG IS NOT WATERPROOF—KEEP DRY.

Before use

Remove the connector cover.

How to replace the fuse

The location of the fuse differ according to the type of AC

mains plug (figures A and B). Confirm the AC mains plug

fitted and follow the instructions below.

Illustrations may differ from actual AC mains plug.

1. Open the fuse cover with a screwdriver.

2. Replace the fuse and close or attach the fuse cover.

System SC-PT70

This unit SA-PT70

Front speakers SB-HF70

Center speaker SB-HC70

Surround speakers SB-HS70

Subwoofer SB-HW70

Operations in these instructions are described

mainly with the remote control, but you can

perform the operations on this unit if the

controls are the same.

(Side of product)

(Inside of product)

CAUTION!

IF THE FITTED MOULDED PLUG IS UNSUITABLE FOR

THE SOCKET OUTLET IN YOUR HOME THEN THE

FUSE SHOULD BE REMOVED AND THE PLUG CUT

OFF AND DISPOSED OF SAFELY.

THERE IS A DANGER OF SEVERE ELECTRICAL

SHOCK IF THE CUT OFF PLUG IS INSERTED INTO

ANY 13-AMPERE SOCKET.

Figure A Figure B

Fuse cover

Figure A Figure B

Fuse

(5 ampere)

Fuse

(5 ampere)

SC-PT70EB-RQTX1019-B_eng.book Page 2 Thursday, August 13, 2009 5:07 PM

RQTX1019

[Note]

The circled numbers indicated in the operating instructions (e.g. Press [Í]1.) correspond to the circled numbers

in the above.

RETURN

VOL

STOP

1 2 3

4 5 6

7 8

PLAY MODE

VOL

SKIP

SLOW

SKIP

PLAY

PAUSE

DVD

RADIO

EXT-IN

MUTE

SOUND

SURROUND

PLAY

LIST

SLEEP

CH SELECT

SETUP

W.SRD

FL DISPLAY

CANCEL

REPEAT

VOL

MUSIC PORT

OPEN/CLOSE

1 2

4 5 6

7 8

SC-PT70EB-RQTX1019-B_eng.book Page 3 Thursday, August 13, 2009 5:07 PM

RQTX1019

Getting StartedPlaying DiscsOther OperationsReference

Control reference guide

Other Panasonic audio/video equipment may start

functioning when you operate the unit using the supplied

remote control.

You can operate this unit in another mode by setting the

remote control operating mode to “REMOTE 2”.

This unit and remote control must be set to the same

mode.

1 Press [EXT-IN]@ to select “AUX/TV”.

2 Press and hold [1]8 on this unit and [2] on the remote

control until this unit’s display shows “REMOTE 2”.

3 Press and hold [OK]9 and [2] on the remote control for

at least 2 seconds.

To change the mode back to “REMOTE 1”, repeat the

steps above by replacing [2] with [1].

Remote control

Turn this unit on/off (B 9)

Select the play mode (B 13)

Select channels and title numbers etc. / Enter

numbers (B 10, 12)

Set the repeat mode (B 13)

Basic operations for play (B 12)

Select preset radio stations (B 10)

Select surround sound effects (B 11)

Show a disc top menu or program list (B 12, 14)

Select or confirm menu items / Frame-by-frame

(B 12)

Show a disc menu or play list (B 12, 14)

;

Show setup menu or select speaker channel (

9, 12)

Turn Whisper-mode Surround on/off (B 11)

TV operations

Aim the remote control at the Panasonic TV and press

the button.

[Í]: Turn the TV on/off

[AV]: Change the TV’s video input mode

[r, s]: Adjust the TV volume

This may not work properly with some models.

Adjust the volume of this unit

Mute the sound

≥“MUTE” flashes on this unit’s display while the

function is on.

≥

To cancel, press the button again or adjust the volume.

≥

Muting is cancelled when you switch the unit to standby.

Source select

[DVD]: Select disc as the source (B 9)

[RADIO]: Select FM tuner (B 10)

[EXT-IN]: Select external audio as the source (B 10)

AV#AUX/TV# MUSIC P.

^------------------------------}

Select radio stations manually (B 10)

Select sound mode (B 11)

Show START menu (B 10)

Show on-screen menu (B 14)

Return to previous screen (B 12)

Cancel (B 13)

Switch information on this unit’s display (B 12)

Set the Sleep timer

Press and hold [—SLEEP].

While the time is shown on this unit’s display, press

[—SLEEP] repeatedly.

SLEEP 30 # SLEEP 60 # SLEEP 90 # SLEEP 120

^-------------------------- OFF (Cancel) (--------------------------}

≥To confirm the remaining time, press and hold the

button again.

Avoiding interference with other Panasonic equipment

This unit

Standby/on switch (Í/I)

Press to switch the unit from on to standby mode or

vice versa. In standby mode, the unit is still

consuming a small amount of power. (B 12)

Open/Close the disc tray (B 12)

Remote control signal sensor

Display

Connect external music device (B 17)

Adjust the volume of this unit

Stop playing

Play disc (B 12)

Language code list

Abkhazian: 6566

Afar: 6565

Afrikaans: 6570

Albanian: 8381

Ameharic: 6577

Arabic: 6582

Armenian: 7289

Assamese: 6583

Aymara: 6589

Azerbaijani: 6590

Bashkir: 6665

Basque: 6985

Bengali, Bangla: 6678

Bhutani: 6890

Bihari: 6672

Breton: 6682

Bulgarian: 6671

Burmese: 7789

Byelorussian: 6669

Cambodian: 7577

Catalan: 6765

Chinese: 9072

Corsican: 6779

Croatian: 7282

Czech: 6783

Danish: 6865

Dutch: 7876

English: 6978

Esperanto: 6979

Estonian: 6984

Faroese: 7079

Fiji: 7074

Finnish: 7073

French: 7082

Frisian: 7089

Galician: 7176

Georgian: 7565

German: 6869

Greek: 6976

Greenlandic: 7576

Guarani: 7178

Gujarati: 7185

Hausa: 7265

Hebrew: 7387

Hindi: 7273

Hungarian: 7285

Icelandic: 7383

Indonesian: 7378

Interlingua: 7365

Irish: 7165

Italian: 7384

Japanese: 7465

Javanese: 7487

Kannada: 7578

Kashmiri: 7583

Kazakh: 7575

Kirghiz: 7589

Korean: 7579

Kurdish: 7585

Laotian: 7679

Latin: 7665

Latvian, Lettish: 7686

Lingala: 7678

Lithuanian: 7684

Macedonian: 7775

Malagasy: 7771

Malay: 7783

Malayalam: 7776

Maltese: 7784

Maori: 7773

Marathi: 7782

Moldavian: 7779

Mongolian: 7778

Nauru: 7865

Nepali: 7869

Norwegian: 7879

Oriya: 7982

Pashto, Pushto: 8083

Persian: 7065

Polish: 8076

Portuguese: 8084

Punjabi: 8065

Quechua: 8185

Rhaeto-Romance:

8277

Romanian: 8279

Russian: 8285

Samoan: 8377

Sanskrit: 8365

Scots Gaelic: 7168

Serbian: 8382

Serbo-Croatian: 8372

Shona: 8378

Sindhi: 8368

Singhalese: 8373

Slovak: 8375

Slovenian: 8376

Somali: 8379

Spanish: 6983

Sundanese: 8385

Swahili: 8387

Swedish: 8386

Tagalog: 8476

Tajik: 8471

Tamil: 8465

Tatar: 8484

Telugu: 8469

Thai: 8472

Tibetan: 6679

Tigrinya: 8473

Tonga: 8479

Turkish: 8482

Turkmen: 8475

Twi: 8487

Ukrainian: 8575

Urdu: 8582

Uzbek: 8590

Vietnamese: 8673

Volapük: 8679

Welsh: 6789

Wolof: 8779

Xhosa: 8872

Yiddish: 7473

Yoruba: 8979

Zulu: 9085

SC-PT70EB-RQTX1019-B_eng.book Page 4 Thursday, August 13, 2009 5:07 PM

Getting StartedPlaying DiscsOther OperationsReference

RQTX1019

Getting Started

Caution for AC Mains Lead . . . . . . . . . . . . . . . . 2

Control reference guide . . . . . . . . . . . . . . . . . . . 4

Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Licenses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

step 1 Installation . . . . . . . . . . . . . . . . . . . . . . 7

step 2 Connections . . . . . . . . . . . . . . . . . . . . . 7

Speaker connections . . . . . . . . . . . . . . . . .7

Radio antenna connections . . . . . . . . . . . .8

Audio and video connections . . . . . . . . . . .8

step 3 AC mains lead connection . . . . . . . . . 9

step 4 Preparing the remote control . . . . . . . 9

step 5 EASY SETUP

. . . . . . . . . . . . . . . . . . . . . 9

Setting up the radio. . . . . . . . . . . . . . . . . . . . . . 10

Presetting stations automatically . . . . . . . . . . . . . . . 10

Confirming the preset channels . . . . . . . . . . . . . . . . 10

Manual tuning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Selecting the playback source. . . . . . . . . . . . . 10

Selecting the source from the START menu . . . . . . 10

Selecting the source by the remote control . . . . . . . 10

Playing Discs

Basic play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Other modes of play . . . . . . . . . . . . . . . . . . . . . 13

Repeat play. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Program and Random play. . . . . . . . . . . . . . . . . . . 13

Using navigation menus . . . . . . . . . . . . . . . . . . 13

Playing data discs. . . . . . . . . . . . . . . . . . . . . . . . . . 13

Playing DVD-R/-RW (DVD-VR) discs. . . . . . . . . . . 14

Using on-screen menus . . . . . . . . . . . . . . . . . . 14

Other Operations

Using the VIERA Link “HDAVI Control

” . . . . 16

One touch play . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Auto input switching . . . . . . . . . . . . . . . . . . . . . . . . 16

Power off link . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Speaker control. . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

VIERA Link Control only with TV’s remote control

(for “HDAVI Control 2 or later”). . . . . . . . . . . . . . . 17

Playing from MUSIC PORT . . . . . . . . . . . . . . . . 17

Reference

Changing the player settings . . . . . . . . . . . . . . 17

DivX information . . . . . . . . . . . . . . . . . . . . . . . . 20

Displaying DivX subtitles text . . . . . . . . . . . . . . . . . 20

Speaker installation option. . . . . . . . . . . . . . . . 21

Discs that can be played. . . . . . . . . . . . . . . . . . 21

Troubleshooting guide . . . . . . . . . . . . . . . . . . . 22

Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Safety precautions . . . . . . . . . . . . . . Back cover

Enjoying sound effects from all speakers

Enjoying surround sound effects . . . . . . . . . . . . . 11

Selecting sound mode . . . . . . . . . . . . . . . . . . . . . . 11

Whisper-mode Surround . . . . . . . . . . . . . . . . . . . . 11

Adjusting the speaker output level manually . . . 11

Adjusting the balance of the front speakers . . . . 12

QUICK START GUIDEQUICK START GUIDEQUICK START GUIDE

CAUTION!

THIS PRODUCT UTILIZES A LASER.

USE OF CONTROLS OR ADJUSTMENTS OR

PERFORMANCE OF PROCEDURES OTHER THAN

THOSE SPECIFIED HEREIN MAY RESULT IN

HAZARDOUS RADIATION EXPOSURE.

DO NOT OPEN COVERS AND DO NOT REPAIR

YOURSELF. REFER SERVICING TO QUALIFIED

PERSONNEL.

WARNING:

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK

OR PRODUCT DAMAGE,

≥DO NOT EXPOSE THIS APPARATUS TO RAIN,

MOISTURE, DRIPPING OR SPLASHING AND THAT

NO OBJECTS FILLED WITH LIQUIDS, SUCH AS

VASES, SHALL BE PLACED ON THE APPARATUS.

≥USE ONLY THE RECOMMENDED ACCESSORIES.

≥DO NOT REMOVE THE COVER (OR BACK); THERE

ARE NO USER SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE

PERSONNEL.

THIS UNIT IS INTENDED FOR USE IN MODERATE

CLIMATES.

CAUTION!

≥DO NOT INSTALL OR PLACE THIS UNIT IN A

BOOKCASE, BUILT-IN CABINET OR IN ANOTHER

CONFINED SPACE. ENSURE THE UNIT IS WELL

VENTILATED. TO PREVENT RISK OF ELECTRIC

SHOCK OR FIRE HAZARD DUE TO OVERHEATING,

ENSURE THAT CURTAINS AND ANY OTHER

MATERIALS DO NOT OBSTRUCT THE VENTILATION

VENTS.

≥DO NOT OBSTRUCT THE UNIT’S VENTILATION

OPENINGS WITH NEWSPAPERS, TABLECLOTHS,

CURTAINS, AND SIMILAR ITEMS.

≥DO NOT PLACE SOURCES OF NAKED FLAMES,

SUCH AS LIGHTED CANDLES, ON THE UNIT.

≥DISPOSE OF BATTERIES IN AN ENVIRONMENTALLY

FRIENDLY MANNER.

This product may receive radio interference caused by

mobile telephones during use. If such interference is

apparent, please increase separation between the product

and the mobile telephone.

The socket outlet shall be installed near the equipment and

easily accessible.

The mains plug of the power supply cord shall remain

readily operable.

To completely disconnect this apparatus from the AC

Mains, disconnect the power supply cord plug from AC

receptacle.

TABLE OF CONTENTS

SC-PT70EB-RQTX1019-B_eng.book Page 5 Thursday, August 13, 2009 5:07 PM

RQTX1019

Getting StartedPlaying DiscsOther OperationsReference

∫ Sales and Support Information

Customer Care Centre

≥For customers within the UK: 0844 844 3852

≥For customers within the Republic of Ireland:

01 289 8333

≥Visit our website for product information

≥E-mail: customer[email protected]

Direct Sales at Panasonic UK

≥For customers: 0844 844 3856

≥Order accessory and consumable items for your

product with ease and confidence by phoning our

Customer Care Centre Monday-Thursday 9:00am-

5:30pm, Friday 9:30am-5:30pm (Excluding public

holidays).

≥Or go on line through our Internet Accessory ordering

application at www.panasonic.co.uk.

≥Most major credit and debit cards accepted.

≥All enquiries transactions and distribution facilities are

provided directly by Panasonic UK Ltd.

≥It couldn’t be simpler!

≥Also available through our Internet is direct shopping for

a wide range of finished products, take a browse on our

website for further details.

Interested in purchasing an extended guarantee?

Please call 0870 240 6284 or visit our website

www.panasonic.co.uk/guarantee

Licenses

Accessories

Please check and identify the supplied

accessories. Use numbers indicated in

parentheses when asking for

replacement parts.

(Product numbers correct as of August

2009. These may be subject to change.)

1 Remote control (N2QAYB000456)

2 Remote control batteries

1 FM indoor antenna (RSAX0002)

1 Antenna plug adaptor (K1YZ02000013)

1 AC mains lead (K2CZ3YY00005)

5 Speaker cables

[

REEX1102

(blue)], [

REEX1103

(grey)],

[REEX1104 (green)], [REEX1105 (white)],

[REEX1106 (red)]

1 Sheet of speaker cable stickers

Manufactured under license from Dolby Laboratories.

Dolby, Pro Logic, and the double-D symbol are

trademarks of Dolby Laboratories.

Manufactured under license under U.S. Patent #’s:

5,451,942; 5,956,674; 5,974,380; 5,978,762;

6,487,535 & other U.S. and worldwide patents issued

& pending. DTS and DTS Digital Surround are

registered trademarks and the DTS logos and Symbol

are trademarks of DTS, Inc. c 1996-2008 DTS, Inc.

U.S. Patent Nos. 6,836,549; 6,381,747; 7,050,698;

6,516,132; and 5,583,936.

This product incorporates copyright protection

technology that is protected by U.S. patents and other

intellectual property rights. Use of this copyright

protection technology must be authorized by

Macrovision, and is intended for home and other

limited viewing uses only unless otherwise authorized

by Macrovision. Reverse engineering or disassembly

is prohibited.

HDMI, the HDMI logo and High-Definition Multimedia

Interface are trademarks or registered trademarks of

HDMI Licensing LLC.

HDAVI Control

is a trademark of Panasonic

Corporation.

Windows Media and the Windows logo are

trademarks or registered trademarks of Microsoft

Corporation in the United States and/or other

countries.

This product is protected by certain intellectual

property rights of Microsoft Corporation and third

parties. Use or distribution of such technology outside

of this product is prohibited without a license from

Microsoft or an authorized Microsoft subsidiary and

third parties.

This product is licensed under the MPEG-4 Visual

patent portfolio license for the personal and non-

commercial use of a consumer for (i) encoding video

in compliance with the MPEG-4 Visual Standard

(“MPEG-4 Video”) and/or (ii) decoding MPEG-4 Video

that was encoded by a consumer engaged in a

personal and non-commercial activity and/or was

obtained from a video provider licensed by MPEG LA

to provide MPEG-4 Video. No license is granted or

shall be implied for any other use. Additional

information including that relating to promotional,

internal and commercial uses and licensing may be

obtained from MPEG LA, LLC. See http://

www.mpegla.com.

Plays DivX

video

DivX

is a registered trademark of DivX, Inc., and is

used under license.

SC-PT70EB-RQTX1019-B_eng.book Page 6 Thursday, August 13, 2009 5:07 PM

RQTX1019

Getting Started

Notes on speaker use

≥Use only supplied speakers

Using other speakers can damage the unit, and sound

quality will be negatively affected.

≥You can damage your speakers and shorten their

useful life if you play sound at high levels over

extended periods.

≥Reduce the volume in the following cases to avoid

damage:

–When playing distorted sound.

–When the speakers are reverberating due to a record

player, noise from FM broadcasts, or continuous

signals from an oscillator, test disc, or electronic

instrument.

–When adjusting the sound quality.

–When turning the unit on or off.

If irregular colouring occurs on your TV

The center speaker is designed to be used close to a

TV, but the picture may be affected with some TVs and

setup combinations.

If this occurs, turn the TV off for about 30 minutes.

The demagnetising function of the TV should correct the

problem. If it persists, move the speakers further away

from the TV.

Caution

Do not touch the front netted area of the speakers. Hold

by the sides.

Turn off all equipment before connection and read the appropriate operating instructions.

Do not connect the AC mains lead until all other connections are completed.

Pay attention to the type of speaker and the connector

colour when you place the speakers.

This unit (rear)

Connect to the terminals of the same colour.

Use of the speaker cable stickers is convenient when

making cable connections.

Speakers (rear)

Insert the wire fully, taking care not to insert beyond the

wire insulation.

i: White

j: Blue line

≥Be careful not to cross (short circuit) or reverse the

polarity of the speaker wires as doing so may damage

the speakers.

(Continued on next page)

step 1 Installation

How you set up your speakers can affect the bass and

the sound field.

Note the following points:

≥Place speakers on flat secure bases.

≥Placing speakers too close to floors, walls, and corners

can result in excessive bass. Cover walls and windows

with thick curtains.

≥For optional wall mount, refer to page 21.

[Note]

Keep your speakers at least 10 mm away from the

system for proper ventilation.

Setup example (Recommended: 5.1ch layout)

Place the front, center, and surround speakers at approximately the same distance from the seating position. The

angles in the diagram are approximate.

§1

Position with at least 5 cm of space on all sides for proper ventilation.

§2

Put on a rack or shelf. Vibration caused by the speaker can disrupt the picture if it is placed directly on the TV.

§3

Place to the right or left of the TV, on the floor or a sturdy shelf so that it will not cause vibration. Leave about

30 cm from the TV.

Depending on the room layout, you may like to use only the front speakers and subwoofer for space saving

(2.1ch layout).

120°

60°

Front speaker

(left)

Front speaker

(right)

Surround

speaker (right)

Surround

speaker (left)

Center speaker

Subwoofer

This unit

2

1

3

Caution

≥This unit and supplied speakers are to be used

only as indicated in this setup. Failure to do so

may lead to damage to the amplifier and/or the

speakers, and may result in the risk of fire.

Consult a qualified service person if damage has

occurred or if you experience a sudden change

in performance.

≥Do not attempt to attach these speakers to walls

using methods other than those described in this

manual.

step 2 Connections

Speaker connections

QUICK START GUIDEQUICK START GUIDEQUICK START GUIDE

step 1-2

SC-PT70EB-RQTX1019-B_eng.book Page 7 Thursday, August 13, 2009 5:07 PM

RQTX1019

Basic setup example

[\\\\\\\\\\\HDMI\AV\OUT\\\\\\\\\]

This connection provides the best picture quality.

Connect the HDMI cable (not included) from the

HDMI AV OUT terminal on this unit to the HDMI AV

IN terminal on your TV.

≥Set “VIDEO PRIORITY” to “ON” (B 19, HDMI menu).

≥Set “VIDEO FORMAT” in Menu 4 (HDMI) (B 16).

VIERA Link “HDAVI Control”

If your Panasonic TV is VIERA Link compatible, you can

operate your TV synchronising with home theater

operations or vice versa (B 16, Using the VIERA Link

“HDAVI Control

”).

≥Make the extra audio connection (B right) when you

use

VIERA Link “

HDAVI Control

”

function.

[Note]

≥Non-HDMI-compliant cables cannot be utilized.

≥It is recommended that you use Panasonic’s HDMI

cable. Recommended part number:

RP-CDHG15 (1.5 m), RP-CDHG30 (3.0 m),

RP-CDHG50 (5.0 m), etc.

≥For TV with more than one HDMI terminal, refer to the

operating instructions for the TV to determine which

terminal to connect to.

≥Do not make the video connections through the

VCR.

Due to copy guard protection, the picture may not be

displayed properly.

≥Only one video connection is required. Choose one of

the video connections above depending on your TV.

[\\\\\\\\\AUX/TV\\\\\\\\]

This connection enables you to play audio from your TV,

STB or VCR through your home theater system (B 10,

Selecting the source by the remote control).

Connect the audio cable (not included) from the

AUX/TV terminal on this unit to the AUDIO OUT

terminal on your TV.

[Note]

If you have various sound sources (such as Blu-ray

player, DVD recorder, VCR, etc.), connect them to the

available inputs on the TV and the TV output should

then be connected to the AUX/TV terminal of this unit.

Radio antenna connections

Using an indoor antenna

Adhesive tape

This unit (rear)

FM indoor antenna

(included)

Affix this end of the antenna

where reception is best.

FM ANT

(75 )

Using an outdoor antenna

75  coaxial cable

(not included)

FM ANT

(75 )

This unit

(rear)

FM outdoor antenna

[Using a TV antenna

(not included)]

The antenna should

be installed by a

competent technician.

Use the antenna

plug adaptor

(included).

Use outdoor antenna if radio reception is poor.

≥Disconnect the antenna when the unit is not in use.

≥Do not use the outdoor antenna during an electrical

storm.

Audio and video connections

AV OUT

AV1

AV2

Scart cable (not included)

TV (not included)

This unit (rear)

Set top box

(STB) or VCR

(not included)

Scart cable

(not included)



This connection will also enable you to play TV

audio through your home theater system (B 10,

Selecting the source by the remote control). Select

the appropriate audio out (e.g. Monitor) on the TV.

If Scart terminal is not available on your TV, use

AUX/TV connection (B below).

≥When both the HDMI cable and scart cable are

connected, there will be no RGB output from the

SCART (AV) terminal.

Other video connection Other audio connection

SC-PT70EB-RQTX1019-B_eng.book Page 8 Thursday, August 13, 2009 5:07 PM

RQTX1019

Getting Started

Conserving power

This unit consumes a small amount of power, even

when it is in standby mode (approx. 0.48 W). To save

power when the unit is not to be used for a long time,

unplug it from the household mains socket.

You will need to reset some memory items after

plugging in this unit.

[Note]

The included AC mains lead is for use with this unit only.

Do not use it with other equipment. Also, do not use

cords for other equipment with this unit.

Do not:

≥mix old and new batteries.

≥use different types of batteries at the same time.

≥take apart or short circuit.

≥attempt to recharge alkaline or manganese batteries.

≥use batteries if the covering has been peeled off.

Mishandling of batteries can cause electrolyte leakage

which can severely damage the remote control.

Remove the batteries if the remote control is not going to be

used for a long period of time. Store in a cool, dark place.

Aim at the remote control signal sensor (B 4), avoiding

obstacles, at a maximum range of approx. 7 m directly

in front of the unit.

The Easy setup screen assists you in making

necessary settings.

≥Language

Select the language used on menu screen.

≥TV aspect

Select the aspect to suit your TV.

≥Speakers position

Select “5.1ch layout” mode or “2.1ch layout” mode

according to your speaker layout (B 7, Installation).

≥Speaker check

Listen to speaker output to confirm speaker connections.

≥Speaker output

Make surround sound setting for speaker output.

Only when “5.1ch layout” mode is selected in

“Speakers position” above.

[Note]

≥

If this unit is connected to a “HDAVI Control 3 or later”

compatible TV via HDMI cable, the menu language and

TV aspect information will be retrieved via VIERA Link.

≥If this unit is connected to a “HDAVI Control 2”

compatible TV via HDMI cable, the menu language

information will be retrieved via VIERA Link.

≥Settings in the Easy setup can also be changed in the

player settings [e.g. language, TV aspect (B 17)].

step 3 AC mains lead connection

BE SURE TO READ THE CAUTION FOR THE AC

MAINS LEAD ON PAGE 2 BEFORE CONNECTION.

AC IN

To household mains socket

AC mains lead (included)

This unit (rear)

step 4 Preparing the remote control

Batteries

CAUTION

Danger of explosion if battery is incorrectly replaced.

Replace only with the same or equivalent type

recommended by the manufacturer.

Dispose of used batteries according to the

manufacturer’s instructions.

R6/LR6, AA

Insert so the poles ( and ) match those in the

remote control.

Press in and lift up.

Replace the cover.

≥Use alkaline or manganese batteries.

≥Do not heat or expose to flame.

≥Do not leave the battery(ies) in an automobile

exposed to direct sunlight for a long period of time

with doors and windows closed.

Use

step 5 EASY SETUP

Preparation

Turn on your TV and select the appropriate video input

mode (e.g. VIDEO 1, AV 1, HDMI, etc.) to suit the

connections to this unit.

≥To change your TV’s video input mode, refer to its

operating instructions.

≥This remote control can perform some basic TV

operations (B 4).

Press [Í]1 to turn on the unit.

≥When the Easy setup screen appears

automatically, skip step 2 to 6.

Press [DVD]@ to select “DVD/CD”.

Press [SETUP]; to show the setup menu.

Press [

]

to select “OTHERS” and press [OK]

Press [

]

to select “EASY SETUP” and press

[OK]

Press [OK]9 to select “SET”.

SET

MAIN

DISC

VIDEO

AUDIO

DISPLAY

HDMI

OTHERS

EXIT : SETUP

RETURN

Press [3, 4]9 to select “Yes” and press [OK]9.

Follow the messages and make the settings with

[

]

and [OK]

(

below, Easy setup settings)

Press [OK]9 to finish Easy setup.

Easy setup settings

QUICK START GUIDEQUICK START GUIDEQUICK START GUIDE

step 2-5

SC-PT70EB-RQTX1019-B_eng.book Page 9 Thursday, August 13, 2009 5:07 PM

RQTX1019

Getting StartedPlaying DiscsOther OperationsReference

Setting up the radio

Up to 30 stations can be set.

≥“SET OK” is displayed when the stations are set, and

the radio tunes to the last preset station.

≥“ERROR” is displayed when automatic presetting is

unsuccessful. Preset the channels manually (B right).

≥The FM setting is also shown on the TV display.

To cancel the mode, press and hold the button again until

“AUTO ST” is displayed.

≥The mode is also cancelled when you change the

frequency.

Up to 30 stations can be set.

A station previously stored is overwritten when another

station is stored in the same channel preset.

Selecting the playback source

You can select sound effects, desired source, or access

playback/menus by using the START menu.

When “Input Selection” is selected

You can select a desired source from the menu.

≥DVD/CD (B 9), FM (B 10), AV (B right),

AUX/TV (B right), MUSIC PORT (B 17)

When “Sound” is selected

You can select sound quality settings (B 11, Equalizer).

When a disc is loaded, you can also access playback or

menus from the START menu.

e.g. [DVD-V]

When the on-screen control panel appears

e.g. [DVD-V] (when “Playback Disc” is selected from the

START menu)

You can operate the playback with the indicated controls.

[Note]

Confirm the audio connection to the SCART (AV) or

AUX/TV terminal on this unit when you select the

corresponding sources (B 8). Reduce the volume on the

TV to its minimum, and then adjust the volume of this

unit.

Presetting stations automatically

Press [RADIO]@ to select “FM”.

Press [MENU]:.

Each time you press the button:

LOWEST (factory preset):

To begin auto preset with the lowest frequency.

CURRENT:

To begin auto preset with the current frequency.

To change the frequency, refer to “Manual tuning”

(B right).

Press and hold [OK]9.

Release the button when “FM AUTO” is displayed.

The tuner starts to preset all the stations it can

receive into the channels in ascending order.

Confirming the preset channels

Press [RADIO]@ to select “FM”.

Press the numbered buttons to select a channel.

≥To select a 2-digit number

e.g. 12: [S10]3 B [1] B [2]

Alternatively, press [X, W]6.

If noise is excessive

Press and hold [PLAY MODE]2 to display “MONO”.

Manual tuning

Press [RADIO]@ to select “FM”.

Press [6, 5]A to select the frequency.

≥To start automatic tuning, press and hold [6,

5]A until the frequency starts scrolling. Tuning

stops when a station is found.

Presetting stations manually

1 While listening to the radio broadcast

Press [OK]9.

2 While the frequency is flashing on the display

Press the numbered buttons to select a channel.

≥To select a 2-digit number

e.g. 12: [S10]3 B [1] B [2]

Alternatively, press [X, W]6, and then press [OK]9.

Selecting the source from the START menu

Press [START]C to show the START menu.

This unit automatically turns on.

(The TV also turns on when using VIERA Link “HDAVI

Control”. This works only when in “DVD/CD” mode

without any disc being loaded.)

e.g.

Press [

]

to select an item and press [OK]

≥To exit, press [START]C.

Press [

]

to make the setting and press

[OK]

DVD/CD Home Cinema

Input Selection

Sound

DVD/CD Home Cinema

Input Selection

Sound

Playback Disc

TOP MENU (DVD)

MENU (DVD)

Playback/menu access

Selecting the source by the remote control

Press To select

[DVD]@ DVD/CD

[RADIO]@ FM

[EXT-IN]@ Each time you press the button:

AV: For audio input through the

SCART (AV) terminal.

AUX/TV: For audio input through the

AUX/TV terminal.

MUSIC P.: For audio input through MUSIC

PORT. (B 17)

SC-PT70EB-RQTX1019-B_eng.book Page 10 Thursday, August 13, 2009 5:07 PM

RQTX1019

Getting StartedPlaying DiscsOther OperationsReference

≥The following sound effects may not be available or

may have no effect with some sources.

≥

You may experience a reduction in sound quality when

these sound effects are used with some sources. If this

occurs, turn the sound effects off.

“SRD” lights in this unit’s display when there is output

from the surround speakers.

For “2.1ch layout”

mode

STANDARD:

Sound is output as it was recorded/encoded. Speaker

output varies depending on the source.

STEREO:

You can play any source in stereo. Surround sound

effect is unavailable.

A.SRD:

You can enjoy surround effect with any audio source.

When the signal is DTS or Dolby Digital, “/DTS” or

“/DOLBY DIGITAL” will also be displayed respectively.

Selected mode in “Speakers position” (B 9, Easy

setup settings).

Except [DivX]

You can enhance the surround effect for low volume 5.1-

channel sound. (Convenient for late night viewing.)

[Only when “5.1ch layout” mode is selected in “Speakers

position” (B 9, Easy setup settings).]

Preparation

≥To display the picture, turn on the TV and select the

appropriate video input mode.

≥Press [r, s VOL]> to adjust the volume to normal

listening level.

≥Select “TEST TONE” from “SPEAKER SETTINGS” in

AUDIO menu (B 19).

(Continued on next page)

Enjoying sound effects from all speakers

Enjoying surround sound effects

Press [SURROUND]7.

Each time you press the button:

For “5.1ch layout”

mode

STANDARD:

Sound is output as it was recorded/encoded. Speaker

output varies depending on the source.

MULTI-CH:

You can enjoy sound from the front speakers, as well as

the surround speakers even when playing a 2-channel

sound or non-surround sound.

MANUAL: (B below)

While “MANUAL” is displayed, press [2, 1]9 to

select other surround modes.

Each time you press [2, 1]9:

DOLBY PLII MOVIE

Suitable for movie software, or softwares recorded in

Dolby Surround. (except [DivX])

DOLBY PLII MUSIC

Adds 5.1-channel effects to stereo sources. (except

[DivX])

S.SRD

You can enjoy sound from all speakers with stereo

sources. (Surround output will be in mono.)

STEREO

Sound will only be output to the front speakers and the

subwoofer from any source.

Recommended modes to enjoy TV audio or

stereo sources from all speakers:

≥DOLBY PLII

MOVIE

≥DOLBY PLII

MUSIC

≥S.SRD

Selecting sound mode

Press [SOUND]B to select a sound mode.

Each time you press the button:

EQ: Equalizer

SUBW LVL: Subwoofer Level

C.FOCUS: Center Focus [Only when “5.1ch

layout” mode is selected in “Speakers

position” (B 9, Easy setup settings).]

While the selected mode is displayed, press

[2, 1]9 to make the settings.

Refer to the following for setting details of each sound

effect.

Equalizer

You can select sound quality settings.

Each time you press [2, 1]9:

HEAVY: Adds punch to rock.

CLEAR: Clarifies higher sounds.

SOFT: For background music.

FLAT: Cancel (no effect is added).

Subwoofer level

You can adjust the amount of bass. The unit

automatically selects the most suitable setting

according to the type of playback source.

SUB W 1

SUB W 2

SUB W 3

SUB W 4

^-------------------------------------------------------------------J

≥The setting you make is retained and recalled

every time you play the same type of source.

Center Focus

(Effective when playing audio containing

center channel sound.)

You can make the sound of the center speaker

seem like it is coming from within the TV.

C.FOCUS ON,------.C.FOCUS OFF

Whisper-mode Surround

Press [W.SRD]<.

Each time you press the button:

WHISPER-MODE SRD ON

,--.

WHISPER-MODE SRD OFF

Adjusting the speaker output level manually

SC-PT70EB-RQTX1019-B_eng.book Page 11 Thursday, August 13, 2009 5:07 PM

RQTX1019

Getting StartedPlaying DiscsOther OperationsReference

[Effective only when “5.1ch layout” mode is selected in

“Speakers position” (B 9, Easy setup settings) and

playing 5.1-channel sound.]

Basic play

Preparation

To display the picture, turn on your TV and change its

video input mode (e.g. VIDEO 1, AV 1, HDMI, etc.) to suit

the connections to this unit.

[Note]

≥DISC CONTINUES TO ROTATE WHILE MENUS ARE

DISPLAYED.

To preserve the unit’s motor and your TV screen, press

[∫ STOP]5 when you are finished with the menus.

≥Total title number may not be displayed properly on

iR/iRW.

≥ABOUT DIVX VIDEO:

DivX

is a digital video format created by DivX, Inc. This

is an official DivX Certified device that plays DivX video.

Press [OK]9 to enter test tone mode.

Test tone will be output to each channel in the

following order.

LEFT, CENTER, RIGHT, SURROUND RIGHT,

SURROUND LEFT

Press [OK]9 then [3, 4]9 to adjust the speaker

level for each speaker. (CENTER, SURROUND

RIGHT, SURROUND LEFT)

6dB to

6 dB (Factory preset: 0 dB)

≥To exit the screen, press [SETUP];.

To adjust speaker level during play

1 Press and hold [—CH SELECT]; to select the

speaker.

While the speaker channel is displayed, press

[—CH SELECT];.

L# C# R# RS# LS# SW

^---------------------------------------------}

≥You can adjust SW (Subwoofer) only if the disc

includes a subwoofer channel.

≥

“S” appears on this unit’s display when you have

selected “S.SRD” (

B 11

, Enjoying surround sound

effects). In this case, you can adjust both surround

speaker levels at the same time using

[3, 4]9

S: `6dB to i6dB

2 Press [3]9 (increase) or [4]9 (decrease) to

adjust the speaker level for each speaker.

C, RS, LS, SW: `6dB to i6dB

(L, R: Only the balance is adjustable.) (B below)

Adjusting the balance of the front speakers

Press and hold [—CH SELECT]; to select “L” or

“R”.

While “L” or “R” is selected, press [2, 1]9.

Press [Í/I]1 or [Í]1 to turn on the unit.

Press [DVD]@ to select “DVD/CD”.

Press [< OPEN/CLOSE]2 to open the disc tray.

Load the disc.

≥Load double-sided discs so the

label for the side you want to play

is facing up.

Press [1]8 or [1 PLAY]5 to start play.

≥Press [r, s VOL]6/> to adjust the volume.

e.g.

AUDIO-SPEAKER SETTINGS-TEST TONE

SPEAKER

LEFT

CENTER

RIGHT

SURROUND RIGHT

SURROUND LEFT

TRIM LEVEL

− −

0dB

− −

0dB

Label facing up

Basic controls

One touch play (remote control only): [1 PLAY]5

(during standby mode)

This unit automatically turns on and starts playing the

disc in the tray.

Stop: [∫ STOP]5

The position is memorised while “RESUME STOP” is on

the screen.

≥Press [1 PLAY]5 to resume.

≥Press [∫ STOP]5 again to clear the position.

Pause: [; PAUSE]5

≥Press [1 PLAY]5 to restart play.

Skip: [:, 9 SKIP]5

Search: [6, 5]5 (during play)

≥Up to 5 steps.

≥Press [1 PLAY]5 to start normal play.

Slow-motion: [6, 5]5 (during pause)

≥[VCD] Slow-motion: Forward direction only.

≥[MPEG4] [DivX] Slow-motion: Does not work.

Frame-by-frame: [2;, ;1]9 (during pause)

[DVD-VR] [DVD-V] [VCD]

≥[DVD-VR] [VCD]

Forward direction only.

On-screen item select: [3, 4, 2, 1, OK]9

[3, 4, 2, 1]9: Select

[OK]9: Confirm

Enter number: Numbered buttons

[DVD-VR] [DVD-V] [VCD] [CD]

e.g. To select 12: [S10]3 B [1] B [2]

[VCD] with playback control

Press [∫ STOP]5 to cancel the PBC function, and then

press the numbered buttons.

[DVD-V] Show a disc top menu: [TOP MENU]8

[DVD-V] Show a disc menu: [MENU]:

Return to previous screen: [RETURN]E

[VCD] (with playback control) Show a disc menu:

[RETURN]E

This unit display: [FL DISPLAY]G

[DVD-VR] [DVD-V] [WMA] [MP3] [MPEG4] [DivX]

Time display ,-. Information display (e.g. [DVD-VR]

Program number)

[JPEG]

SLIDE,-.Contents number

SC-PT70EB-RQTX1019-B_eng.book Page 12 Thursday, August 13, 2009 5:07 PM

RQTX1019

Getting StartedPlaying DiscsOther OperationsReference

Other modes of play

This works only when the elapsed play time can be

displayed. It also works with all JPEG content.

Items shown differ depending on the type of disc and

playback mode.

Preparation

≥[DVD-VR] Select “DATA” in “DVD-VR/DATA” (B 20,

OTHERS menu) to play WMA, MP3, JPEG, MPEG4

or DivX contents.

≥If “PLAYBACK MENU” screen appears, select “AUDIO/

PICTURE” or “VIDEO” (B right, Using PLAYBACK

MENU), then proceed with the above.

≥For a disc with both WMA/MP3 and JPEG contents,

select either music or picture contents.

WMA/MP3: Select “MUSIC PROGRAM” or “MUSIC

RANDOM”.

JPEG: Select “PICTURE PROGRAM” or “PICTURE

RANDOM”.

≥[DVD-V] Some items cannot be played even if you have

programmed them.

To select all the items

Press [3, 4]9 to select “ALL” and press [OK]9.

To clear the selected program

1 Press [1]9 and then press [3, 4]9 to select the

program.

2 Press [CANCEL]F.

To clear the whole program

Press [1]9 several times to select “CLEAR ALL”, and

then press [OK]9.

The whole program is also cleared when the disc tray is

opened, the unit is turned off or another source is

selected.

Using navigation menus

[DVD-VR] Select “DATA” in “DVD-VR/DATA” (B 20,

OTHERS menu) to play WMA, MP3, JPEG, MPEG4 or

DivX contents.

“PLAYBACK MENU” screen appears when the disc

contains both video (MPEG4/DivX) and other format

(WMA/MP3/JPEG).

You can select to play from your desired item while the

“DATA-DISC” screen is displayed.

e.g.

≥To display/exit the screen, press [MENU]:.

Play starts from the selected content.

(Continued on next page)

Repeat play

During play, press [REPEAT]4 to select an item to

be repeated.

e.g. [DVD-V]

`TITLE ---. `CHAP. ---. `OFF

^----------------------------------------------------b

To cancel, select “OFF”.

Program and Random play

[DVD-V] [VCD] [CD] [WMA] [MP3] [JPEG] [MPEG4] [DivX]

While stopped, press [PLAY MODE]2 to select the

play mode.

Program and random playback screens appear

sequentially.

Program ------------------------------------------) Random

^--- Exit program and random screens (}

Program play (up to 30 items)

Press [3, 4]9 to select an item and press

[OK]9.

e.g. [DVD-V]

≥Repeat this step to program other items.

≥To return to the previous menu, press [RETURN]E.

Press [1 PLAY]5 to start play.

DVD-V PROGRAM

SELECT TITLE

TITLE CHAPTER

TITLE 1

TITLE 2

TITLE 3

TITLE 4

Random play

(Only when the disc has groups or multiple titles.)

Press [3, 4]9 to select a group or title and press

[OK]9.

e.g. [DVD-V]

≥“¢” represents selected. To deselect, press [OK]9

again.

Press [1 PLAY]5 to start play.

Playing data discs

[WMA] [MP3] [JPEG] [MPEG4] [DivX]

Using PLAYBACK MENU

Press [3, 4]9 to select “AUDIO/PICTURE” or

“VIDEO” and press [OK]9.

≥To start play, press [1 PLAY]5.

≥To select an item to play, refer “Playing from the

selected item” (B below).

Playing from the selected item

Press [3, 4]9 to select an item and press [OK]9.

≥Press [2, 1]9 to skip page by page.

≥To return to 1 level up from the current folder, press

[RETURN]E.

≥Maximum: 28 characters for file/folder name.

DVD-V RANDOM

SELECT TITLE

TITLE 1

TITLE 2

TITLE 3

PLAYBACK MENU

WMA/MP3/JPEG

MPEG4/DivX

AUDIO/PICTURE

VIDEO

DATA-DISC

ROOT

RETURN

Perfume

Underwater

Fantasy planet

Starpersons1

Group (Folder):

Content (File):

: WMA/MP3

: JPEG

: MPEG4/DivX

SC-PT70EB-RQTX1019-B_eng.book Page 13 Thursday, August 13, 2009 5:07 PM

RQTX1019

Getting StartedPlaying DiscsOther OperationsReference

∫ [JPEG] Selecting the picture in Thumbnail menu

To go to other group

1Press [3]9 to select the group name.

2Press [2, 1]9 to select the group and press [OK]9.

≥Titles appear only if the titles are recorded on the disc.

≥You cannot edit programs, play lists and disc titles.

This works only when the disc contains a play list.

Using on-screen menus

While picture is displayed, press [TOP MENU]8

to show the thumbnail menu.

e.g.

Press [3, 4, 2, 1]9 to select a picture and

press [OK]9.

≥Press [:, 9 SKIP]5 to skip page by page.

Playing DVD-R/-RW (DVD-VR) discs

[DVD-VR]

Playing the programs

While stopped, press [DIRECT NAVIGATOR]8.

e.g.

≥To exit the screen, press [DIRECT NAVIGATOR]8.

Press [

]

to select the program and press

[OK]

≥Press [2, 1]9 to skip page by page.

Playing a play list

While stopped, press [PLAY LIST]:.

e.g.

≥To exit the screen, press [PLAY LIST]:.

Press [

]

to select the play list and press [OK]

≥Press [2, 1]9 to skip page by page.

Press [FUNCTIONS]D to show the on-screen

menu.

Each time you press the button:

Menu 1 (Disc/Play)

Menu 2 (Video)

Menu 3 (Audio)

Menu 4 (HDMI)

Exit

Press [3, 4, 2, 1]9 to select the item and press

[OK]9.

Press [

]

to make the settings and press [OK]

Press [RETURN]E to exit.

JPEG images G 1/ 1:C 3/ 9

Group name

Group and content

number

DATE

LENGTH

TITLE

0:16:02

10/11

LIVE CONCERT

02:15