Autopage KE-115 Operating instructions

Brand: Autopage

Model: KE-115

Type: Operating instructions

KE-115

CUSTOMER SYSTEM OPERATIONS

ACTIVE LOCKING & UNLOCKING

Active or Manual locking is activating the System by the Remote Control Transmitters.

(Interfacing the vehicles horn and starter interrupt circuit requires additional installation.)

Active locking is as follows…

a) Press button on the Remote Control Transmitter.

b) The horn will honk once, the parking lights will flash once & the doors will lock.

c) A steady flashing of the System LED will confirm locked status.

Unlocking is as follows…

a) Press button on the Remote Control Transmitter.

b) The horn will honk twice, the parking Lts. will flash twice & the doors will unlock.

c) The System LED will turn off indicating unlocked status.

PANIC FUNCTION

In the event of an emergency, the Remote Control Transmitter can be used to activate the

System Panic Mode. (Interfacing the vehicles horn to the System requires additional

installation.) Panic Mode operation is as follows…

a) Push and hold horn button for more than 3 seconds.

b) The horn will begin honking and the vehicles parking lights will begin flashing.

CAR LOCATOR FUNCTION

To help locate your vehicle when out of sight our parked in a crowded parking lot.

(Interfacing the vehicles horn to the System requires additional installation.)

You can activate the Car Locator by:

a) Push button while system is locked

b) The horn will sound chirping 6 times & the parking lights will flash 12 times.

VALET / OVERRIDE SWITCH

(The Valet / Override Switch has dual functions:)

Emergency unlock (To dis-engage the optional starter interrupt circuit) – In the event the

Remote Control Transmitter malfunctions or is lost the System can still be disarmed.

Emergency unlock is activated as follows…

a) Turn the vehicles ignition to the “ON” position and press the Valet / Override

Switch once.

b) The System is now de-activated.

Valet Mode – In the event the vehicle needs to be serviced or valet parked, the System

can be programmed into a “Valet Mode” that will only allow the Remote Control

Transmitters to activate the door lock / unlock circuit. Programming Valet Mode is as

follows…

a) Turn the vehicles ignition to the “ON” position and push the Valet / Override

Switch for 2 seconds or until the System LED turns on solid. The System is now

in Valet mode.

b) To return the System to normal operation, turn the vehicles ignition “ON”

position and push the Valet / Override switch for 2 seconds or until the System

LED turns off. The System has resumed normal operation.

5) IGNITION CONTROLLED DOOR LOCKS

When the vehicles ignition is turned “ON” the door will automatically lock and when the

vehicles ignition is turned “OFF” the doors will automatically unlock. *

6) DOME LIGHT ILLUMINATION

When the System is locked, the vehicles dome light will illuminate for 10 seconds. When

the System is unlocked, the vehicles dome light will illuminate for 30 seconds. *

7) REMOTE CONTROL TRANSMITTER OPERATION

Transmitter Button System Function

Locks the door / flashes the parking lights once /

Activates the horn once* / starter interrupt circuit engaged*

3 Seconds ( Panic )

Activates the horn* / flashes the parking lights

(Push and hold button for 3 sec.)

– Car Locator

Activates the horn* 6 chirps & Flashes parking 12 times

(Push the button when system is activated)

Unlocks the doors / flashes the parking lights twice

Activates the horn twice* / De-activates Panic

Unlocks the Drivers door on the first push, then unlocks the

Rest of the doors on the 2P

push/ flashes parking lights twice.

Activates channel 2 output (Push and hold button

for 3 seconds to activate) Trunk Pop

Panic

Activates the horn* / flashes the parking lights

(Push and hold button for 3 sec.)

+ Silent Locking

Activates silent Locking mode (Push both buttons and

at the same time to activate)*

Optional silent lock and unlock (Programming Required)

* Additional Installation may be required

8) LED & HORN INDICATORS

LED

HORN*

Operation Function Operation Function

Off Unlocked 1 Chirp Locked

Slow Flash Locked 2 Chirps Unlocked

Fast Flash Passive Locking Mode Engaged Continuous Chirp Panic Mode Engaged

On (Solid) Valet Mode

(30 seconds)

* Additional Installation may be required

PARKING LIGHT INDICATORS

PARKING LIGHTS

Operation Function

1 Flash + 10 sec on

Locked / The parking lights will remain “on” for 10 seconds

2 Flashes + 30 sec on

Unlocked / The parking lights will remain “on” for 30 seconds

Continuous Flash

Panic Mode Engaged (30 Sec.)

10)

STARTER INTERRUPT CIRCUIT (OPTIONAL)

The vehicles starter circuit may be interrupted for additional protection when the System is

locked. Use of the RK-1 Starter Interrupt Relay kit is recommended.

11)

TRANSMITTER PROGRAMMING

In the event, you should need to add or replace a Remote Control Transmitter, it is

important that you follow the instructions below.

Note:

Each step must be performed within 10 seconds of the previous step otherwise the System

will exit the programming mode.

PROGRAMMING THE REMOTE TRANSMITTER

Enter:

Turn the Ignition ‘switch ‘OFF/ON’ 3 TIMES and stay in ON

position. Within 15 seconds.

2. Push the Valet switch

2 times. (Holding in on the 2nd push) until you hear a long chirp. The

transmitter is ready to program.

Program:

Press any button on the transmitter until the horn responds with a confirming chirp the first

transmitter is now programmed.

Press button on the second transmitter until the horn responds with a confirming chirp, the

second transmitter is now programmed.

3. Apply the same procedure to program 3rd and 4

Exit:

Turn Ignition to ‘OFF’ position, or leave it for 15 seconds. A 3 long chirps & 3 parking light

flashes to confirm exit.

KE-115

PROFESSIONAL KEYLESS ENTRY SYSTEM

OPERATIONS MANUAL

THIS PRODUCT IS DESIGNED FOR PROFESSIONAL INSTALLATION ONLY

Autopage KE-115 Operating instructions

Autopage KE-115 Operating instructions

Autopage KE-115 Operating instructions

Related papers

Other documents