Power Electronics SDRIVE DBSD4030 Getting Started Manual

DB Series

SDRIVES

DYNAMIC BRAKING

dynamic braking unit

Getting Started Manual

dynamic braking unit

Getting Started Manual

Edition: October 2007

VFDF01AI Rev. A

DB SERIES POWER ELECTRONICS

2

POWER ELECTRONICS DB SERIES

SAFETY SYMBOLS

3

SAFETY SYMBOLS

Always follow safety instructions to prevent accidents and potential hazards

from occurring.

This symbol means improper operation may results in

serious personal injury or death.

Identifies shock hazards under certain conditions.

Particular attention should be given because dangerous

voltage may be present. Maintenance operation should be

done by qualified personnel.

Edition October 2007

This publication could present technical imprecision or misprints. The

information here included will be periodically modified and updated, and all

those modifications will be incorporated in later editions.

To consult the most updated information of this product you might access

through our website

www.power-electronics.com where the latest version of

this manual can be downloaded.

Revisions

Date Revision Description

st

Edition 31 / 10 /2007 A 1

DB SERIES POWER ELECTRONICS

4

POWER ELECTRONICS DB SERIES

INDEX

5

INDEX

SAFETY INSTRUCTIONS..............................................................................7

1. INTRODUCTION ....................................................................................10

1.1. Equipment Description...............................................................10

1.2. Standard Ratings.......................................................................12

2. TECHNICAL CHARACTERISTICS ........................................................13

2.1. Technical Specifications.............................................................13

2.2. Dimensions................................................................................14

3. MOUNTING OF DYNAMIC BRAKING UNIT..........................................16

3.1. Environmental Conditions..........................................................17

4. INSTALLATION OF DYNAMIC BRAKING UNIT ...................................18

4.1. Terminal Configuration...............................................................18

4.2. Leds Description........................................................................20

4.3. Terminals of Braking Resistor....................................................21

4.4. Connection Drawing...................................................................22

4.5. Operating Modes for the Dynamic Braking Unit – GROUP 2......23

4.6. Combination of Dynamic Braking Units according to Drive

Capacity ...................................................................................27

5. DYNAMIC BRAKING RESISTOR ..........................................................32

5.1. Selection of the External Braking Resistor.................................32

DB SERIES POWER ELECTRONICS

6

INDEX

POWER ELECTRONICS DB SERIES

SAFETY INSTRUCTIONS

7

SAFETY INSTRUCTIONS

IMPORTANT!

 Safety instructions showed in this manual are useful to teach user

how to use the product in a correct and safety way with the purpose

of preventing possible personal injuries or property damages.

 Safety messages included here are classified as it follows:

WARNING

Do not remove the cover while the power is applied or the unit is in

operation.

Otherwise, electric shock could occur.

Do not run the braking unit with the front cover removed.

Otherwise, you may get an electric shock due to the high voltage terminals

or exposure of charged capacitors.

Do not remove the cover except for periodic inspections or wiring,

even if the input power is not applied.

Otherwise, you may access the charged circuits and get an electric shock.

Wiring and periodic inspections should be performed at least 10

minutes after disconnecting the input power of the equipment which

is going to be connected with this braking unit and after checking the

DC Link voltage is discharged with a meter (below 30VDC).

Otherwise, you may get an electric shock.

Operate the switches with dry hands.

Otherwise, you may get an electric shock.

Do not use cables with damaged insulation.

Otherwise, you may get an electric shock.

Do not subject the cables to the abrasions, excessive stress, heavy

loads or pinching.

Otherwise, you may get an electric shock.

DB SERIES POWER ELECTRONICS

CAUTION

Install the braking unit on a non-flammable surface. Do not place

flammable material nearby.

Otherwise, fire could occur.

Disconnect the input power if the drive or the braking unit gets

damaged.

Otherwise, it could result in a secondary accident or fire.

Do not connect the braking resistor directly to the DC terminal (P/B1,

N) of the braking unit.

Otherwise, fire could occur.

Do not touch the braking unit, drive and the resistor right after the

power is turn off.

The resistor is still hot.

Do not apply power to a damaged drive or braking unit, or to a drive

or braking unit with parts missing even if the installation is

complete.

Otherwise, fire or accident could occur.

Do not allow lint, paper, wood chips, dust, metallic chips or other

foreign matter into the braking unit.

Otherwise, fire or accident could occur.

WARNINGS

RECEPTION

 Material of Power Electronics is carefully tested and perfectly

packed before leaving the factory.

 In the even of transport damage, please ensure that you notify

the transport agency and POWER ELECTRONICS: 902 40 20 70

(International +34 96 136 65 57) or your nearest agent, within

24hrs from receipt of the goods.

8

SAFETY INSTRUCTIONS

POWER ELECTRONICS DB SERIES

SAFETY INSTRUCTIONS

9

UNPACKING

 Make sure received merchandise corresponds with delivery note,

models and serial numbers.

 Each equipment is supplied with a technical manual.

SEGURIDAD

 Before operating the equipment, read this manual thoroughly to

gain and understanding of the unit. If any doubt exists then

please contact POWER ELECTRONICS, (902 40 20 70 / +34 96

136 65 57) or your nearest agent.

 Wear safety glasses when operating the braking unit close to the

drive with power applied and the front cover is removed.

 Handle the braking unit with care according to its weight.

 Do not place heavy objects on the braking unit.

 Install the braking unit according to the instructions within this

manual.

 Ensure that the mounting orientation is correct.

 Do not drop the braking unit or subject it to impact.

TRIAL RUN

 Follow the steps described in this manual.

 Always apply voltage and current signals to each terminal that

are within levels indicated within this manual. Otherwise, damage

to the braking unit may result.

DB SERIES POWER ELECTRONICS

1. INTRODUCTION

1.1. Equipment Description

When operating with drives which do not include dynamic braking

circuit as standard, and it is necessary to conduct the regenerated

energy, it will connect an optional dynamic braking unit with the

corresponding dynamic braking resistors.

DYNAMIC

BRAKING

UNIT

GROUP 1

10

INTRODUCTION

POWER ELECTRONICS DB SERIES

INTRODUCTION

11

DYNAMIC

BRAKING

UNIT

GROUP 2

DB SERIES POWER ELECTRONICS

1.2. Standard Ratings

The following table shows the dynamic braking unit that should be

used for each drive. It will use a single braking unit or a combination of

them, according to the drive capacity.

DYNAMIC BRAKING UNIT APPLICABLE DRIVES

SD450 SD700

GROUP REFER. DESCRIP.

FRAME REF. FRAME REF.

1 SD45008 SD700095xxxx

SD45012 SD700125xxxx

2

SD45016 SD700185xxxx

Dynamic braking

unit for drives from

3,7 to 11kW (400V)

DBSD4030 1

3 SD45024 SD700245xxxx

3 SD45030 SD700325xxxx

1

Dynamic braking

units for drives from

15 to 18,5kW

(400V)

DBSD4045 2

4 SD45039 SD700385xxxx

4 SD45045 2 SD700485xxxx

Dynamic braking

units for drives from

22 to 30kW (400V)

DBSD4075

5 SD45060 3 SD700605xxxx

5 SD45075 SD700755xxxx

6 SD45090 SD700905xxxx

3

SD45110 SD701155xxxx

7

SD45150 SD701505xxxx

- -

4

SD701705xxxx

2

- - SD702105xxxx

- - SD702505xxxx

Dynamic braking

units for drives from

37 to 75kW (400V)

DBSD4145

5

- - SD702755xxxx

- - SD703305xxxx

- - SD703705xxxx

6

- - SD704605xxxx

12

INTRODUCTION

POWER ELECTRONICS DB SERIES

TECHNICAL CHARACTERISTICS

13

2. TECHNICAL CHARACTERISTICS

2.1. Technical Specifications

GROUP 1 GROUP 2

REFER.

DBSD4030 DBSD4045 DBSD4075 DBSD4145

SPECIF.

Max. DC Input Voltage 750Vdc 750Vdc 750Vdc 750Vdc

Applicable Drive

11kW 15kW 18,5kW 22kW 30kW 37kW 75kW

Capacity

Power 2,5kW 3,5kW 5kW 10kW

Braking

Minimum

resistor

30Ω 20Ω 12Ω 6Ω

resistor

Average braking torque 150% 150% 150% 150%

Enable Duty (ED) 10% 10% 5% 5%

Fault output contact, Slave control

signal

Output signal Heat sink overheat

Protection Heat sink overheat Heat sink overheat, overcurrent

Ambient

-10ºC to +40ºC -10ºC to +40ºC

Temp.

Humidity <90% (non-condensing) <90% (non-condensing)

Altitude <1000m above sea level <1000m above sea level

Cooling

Method

Natural convection Self-cooling

Environ.

Condit.

Environment with no corrosive gas,

combustible gas, oil mist or dust.

Environment with no corrosive gas,

combustible gas, oil mist or dust.

Location

Notes:

• For drive capacities higher than 75kW up to 250kW, se section ‘4.5.4. Combination

of DB Units – Group 2’.

• For drive capacities lower than 11kW and higher than 250kW, contact with Power

Electronics.

DB SERIES POWER ELECTRONICS

2.2. Dimensions

In the following figures, you can observe external dimensions of the

dynamic braking units of groups 1 and 2:

a) Group 1 (DBSD4030 – DBSD4045).

Figure 2.1 Dimensions of dynamic braking unit – Group 1

(DBSD4030 – DBSD4045)

14

TECHNICAL CHARACTERISTICS

POWER ELECTRONICS DB SERIES

TECHNICAL CHARACTERISTICS

15

b) Group 2 (DBSD4075 – DBSD4145).

Figure 2.2 Dimensions of dynamic braking unit – Group 2

(DBSD4075 – DBSD4145)

DB SERIES POWER ELECTRONICS

3. MOUNTING OF DYNAMIC

BRAKING UNIT

Braking units must be mounted vertically with sufficient horizontal and vertical

distance between adjacent equipment.

 A = Higher than 100mm.

 B = Higher than 50mm.

Figure 3.1 Dynamic braking unit mounting (Group 1 and Group 2)

16

MOUNTING OF DYNAMIC BRAKING UNIT

POWER ELECTRONICS DB SERIES

MOUNTING OF DYNAMIC BRAKING UNIT

17

3.1. Environmental Conditions

 Do not mount the braking unit in direct sunlight. Isolate the

braking unit from excessive vibration.

 Protect the braking unit from moisture, dust, metallic particles,

corrosive gasses and liquids. Install the braking unit on a non-

flammable surface and as smooth as possible.

 In case of installing many braking units in a panel, consider the air

flow for power dissipation.

Figure 3.2 Multiple installation of braking units in a panel

Figure 3.3 Fan location in a panel

DB SERIES POWER ELECTRONICS

4. INSTALLATION OF DYNAMIC

BRAKING UNIT

4.1. Terminal Configuration

4.1.1. Dynamic Braking Unit – GROUP 1

Terminals for dynamic braking units of Group 1 are described in the

following table:

TERMINAL DESCRIPTION

CM Common terminal for the over-temperature trip (OH).

Output terminal for the over-temperature trip (Open

collector: 20mA, 27Vdc).

OH

G Ground terminal.

Connection for B2 terminal of the dynamic braking

resistor.

B2

Connection for B1 terminal of the dynamic braking

resistor.

B1

Connection for negative terminal of DC Bus of the drive

(DC Bus (-)).

N

Connection for positive terminal of DC Bus of the drive

(DC Bus (+)).

P

4.1.2. Dynamic Braking Unit – GROUP 2

Power Terminals

Figure 4.1 Power terminals for dynamic braking unit – Group 2

18

INSTALLATION OF DYNAMIC BRAKING UNIT

POWER ELECTRONICS DB SERIES

INSTALLATION OF DYNAMIC BRAKING UNIT

19

TERMINAL DESCRIPTION

G Ground terminal.

Connection for negative terminal of DC Bus of the drive

(DC Bus (-)).

N

Connection for B2 terminal of the dynamic braking

resistor.

B2

Connection for B1 terminal of the dynamic braking

resistor.

P / B1

Connection for positive terminal of DC Bus of the drive

(DC Bus (+)).

Control Terminals

Figure 4.2 Control terminals for dynamic braking unit – Group 2

TERMINAL DESCRIPTION

Input signal (+) to Slave. Only connected when DB Unit

is configured as ‘Slave’.

IN+

[1]

Input signal (-) to Slave. Only connected when DB Unit

is configured as ‘Slave’.

IN-

[1]

Output signal (+) to Slave. In this case, DB Unit can be

configured as ‘Master’ or ‘Slave’.

OUT+

[1]

Output signal (-) to Slave. In this case, DB Unit can be

configured as ‘Master’ or ‘Slave’.

OUT-

[1]

Fault Output signal (Fault Relay).

30A 30A: Normally open contact (NO).

30B 30B: Normally closed contact (NC).

30C 30C: Common terminal.

[1]

Control signals IN+/- and OUT+/- are only used when multiple DB Units

are connected. See section ‘4.5.2. ‘Master / Slave’ Operation Mode’.

Page is loading ...

Power Electronics SDRIVE DBSD4030 Getting Started Manual

This manual is also suitable for

Power Electronics SDRIVE DBSD4030 Getting Started Manual

Other documents