Ariston WITH PUMP is an electric instant water heater that provides hot water on demand. It has a built-in pump that ensures a consistent flow of hot water, even in low-pressure situations. The heater has a temperature control knob that allows you to adjust the water temperature to your desired level. It also has a built-in ELCB (Earth Leakage Circuit Breaker) that protects you from electrical shocks. The heater is easy to install and use, and it comes with a 1-year warranty.
Ariston WITH PUMP is an electric instant water heater that provides hot water on demand. It has a built-in pump that ensures a consistent flow of hot water, even in low-pressure situations. The heater has a temperature control knob that allows you to adjust the water temperature to your desired level. It also has a built-in ELCB (Earth Leakage Circuit Breaker) that protects you from electrical shocks. The heater is easy to install and use, and it comes with a 1-year warranty.
ver. 01
Ariston Thermo Group
Viale Aristide Merloni, 45
60044 Fabriano (AN)
Italy
T. +39 0732 6011
F. +39 0732 602331
www.aristonthermo.com
GB
Electric instant water heater
VN
Máy nước nóng trực tiếp
M
A
X
M
A
X
Model
Watts
Min. Water flow rate l/min
Max. Water flow rate l/min
IP25
Ariston Thermo Group
Viale Aristide Merloni, 45
60044 Fabriano (AN), Italy
www.mtsgroup.com
Voltage
Nr.
1 2
DESCRIPTION OF WATER HEATER
TECHNICAL DATA
WARNING
B G
N V B G
(See Fig. 1)
1. Front Cover
2. Face Panel
3. Face Window
4. Indicator lamps
5. Pump knob
(1)
6. Knob Cover
(2)
7. Temperature Control Knob
8. ELCB Test / Low Pressure Booster
(1)
/ Reset Button
9. Filter Valve
10. Stop Valve
11. Flow Regulator Valve
12. Pressure Relief Valve (Optional)
13. Mouting terminal
14. Hand Shower
15. Adjustable Shower Holder
16. Slider Rail
17. PVC Hose
18. Soap Tray
19. Back Base
20. Water Outlet Pipe
21. Water Inlet Pipe
22. Flow Switch Assy
23. Triac
24. Pump
(1)
25. Switch Mode Power Supply Board
(3)
26. Main PCB Board
27. Potentiometer VR
28. Thermal Cut-Out
29. Auto Reset Thermostat
30. Manual Reset Thermostat
(4)
31. Heater Tank
32. ELCB - 2 Pole assy
(4)
33. Cable Core Hitch
(1) For Pump model only
(2) For No pump model
(3) ForSilent pump model
(4) For model 2P2T only
Single point/Multi point indicator
Serial number
Model
Rated Voltage - Frequency
Power - Current
Minimum flow rate allowable
Maximum flow rate allowable
IP protection grade and
working pressure allowable
For technical characteristics, please refer to the appliance data plate
Thank you for purchasing our instant water heater. Please read the instruction carefully
before use.
Products manufactured by us are safe provided they are installed, used
and maintained in good working order in accordance with our instructions
and recommendations. Always refer to this manual if you have any doubt.
The appliance must be earthed.
- If the Heater begins to make an odd noise, smell or smoke.
- ELCB and Heater lamp does not light up.
- Water temperature can not be controlled.
- If the Heater shows signs of a distinct change in performance.
- If found water leakage from inside.
If any of the following conditions occur, immediately switch off the mains
and contact the sales agent for repair. Never attempt to repair the unit
yourself.
M O D E L WITH PUMP WITHOUT PUMP
D I M EN S I O N S
356 (H) X 245 (W) X 115 (D) mm
W E I G H T 3 . 0 K g 4 . 0 K g
1.
2.
3.
3 4
INSTALLATION INSTRUCTION
B G
N V B G
1. Installation must be carried out by a qualified personnel and in compliance
to the local authority regulations.
2. This heater must be permanently connected to the direct main current
supply. The use of a plug and socket is not recommended.
3. For the correct size of wire conductor corresponding to different electrical
loading. Please refer to Table 1.
4. This heater operates at a minimum water flow rate of 3.0 ltr/min and
maximum water pressure of 6 bar (Multi-Point). For direct connection to the
water tank, the heater must have a minimum of 1.0m below the water tank.
5. This heater will not function if there insufficient water flow (min. 3.0ltr/min)
to trigger the flow switch.
6. In time of thunder, turn off the electric current breaker in advance to protect
the heater.
7. The built-in ELCB will automatic cut off the power supply in case there is a
current leakage as low as 15mA.
8. The thermostat will automatic cut off the power supply if it has sensed an
abnormal rise in showering water temperature.Only qualified technicians are
allowed to reset the thermal cut-out built inside the appliances.
9. (Model Multi-Point) Pressure Relief Valve is to prevents excessive built-up
of water pressure to over 0.65 MPa (6.5bars). The excess will be discharged
through the discharge nozzle, so it should not be removed from the heater. It
is recommended to service the Pressure Relief Valve at least once a year to
prevent blockage.
Caution before
installation !
1. Select a suitable position in the bathroom.
2. Remove the screw A -(fig.2d) at the bottom of the unit and lift up the Front
Cover first at the bottom and then unhook the two parts. Be careful not to
break the Two hook which locate at the top of the Front cover .
3. Mark the screws points of the Heater Base on the wall. The Heater position
should be 1.5 meter from the bathroom floor.
4. If Shower accessory is avaiable (refer fig.2b; 2c), mark the screws points
of the Slider Rail set beside the Heater. It is recommended the top of the
portion is in level with the top of the Heater.
5. Use 6mm diameter drill and make the wall plug holes for Heater and
Shower accessory to 34mm depth.
6. Insert the wall plugs and mount the Heater firmly in position with the
screws provided.
7. To mount Shower accessory, remove the Terminal cover from the Mounting
terminal and screw the Mounting to position. Close the cover. Insert the
Shower Holder and Soap Tray into the Slider Rail. Mount the Slider Rail to the
Mouting terminals and screw the second Mouting to position. Close the cover
Install the
appliance
(For model Single-Point)
1. Connect the Stop Valve to the Water Inlet with rubber washer. Use correct
tools to tighten and be careful not to break the plastic nut.
2. Insert Mesh Filter washer then connect the incoming water piping end to
the Stop Valve (1/2" BSP).
3. Connect the PVC Hose and Hand Shower to the outlet of the Heater, be
sure to put in the rubber washer.
4. Hook the Handshower to the Slider Rail Shower Holder and adjust to your
ideal position.
Important: The 'Water Outlet' can only be fitted to the PVC Hose and
Handshower set provided. NO CONTROL VALVE OR FITTING CAN BE
FITTED TO THE WATER OUTLET.
(For model Multi-Point)
1. Connect Pressure Relief Valve to INLET of water heater (if available). Use
sealing tape for the connection to prevent water leakage. DO NOT apply
excessive force when tightening the Pressure Relief Valve.
2. Insert Mesh Filter washer before connecting the incoming water supply to
Pressure Relief Valve.
Note :
- When connect the Pressure Relief Valve to the water inlet, please make
sure the discharge nozzle facing downward. Connect a discharge pipe (PVC
tube of dia. 8.0mm) to the discharge nozzle in a continuously downward
direction and this pipe must be left open to the atmosphere. In abnormal
condition where pressure gets higher than 6.5 bar, water will drip from this
discharge pipe.
- Connections to the Multi-point hot water system should be limited to 2 or at
the most 3 outlet usage points and they should be near to each other, e.g. in
the same bathroom but only ONE OUTLET POINTS IS TO BE USED AT ANY
ONE TIME. Extensive distance between the appliance and usage point(s) will
result not only loss but also slow response of obtaining the hot water at the
point(s) (fig.2a).
Water
connection
* THE WATER INLET AND OUTLET MUST BE INSTALLED CORRECTLY,
OTHERWISE THE HEATER CAN NOT FUNCTION.
* DO NOT USE PLUMBING CEMENT ON CONNECTION. IF NECESSARY,
USE ONLY THREAD OR SEALING TAPE..
Turn on the water mains to drain out all plumbing dirts and to fill up the heater
tank Check for any water leakage. ( Important:This step will prevent
damage to the heating element ).
Testing
connection
5 6
GB
VN GB
IMPORTANT WARNING:
- This appliance must be EARTHED.
- Remember to SWITCH OFF at mains before carrying out any electrical
work.
- Refer to the TABLE 1 for the correct cable size.
1. Use double coated flexible cable having nominal cross-sectional area
between 4 and 6 mm
2
[ §26.6, IEC/EN 60335-1].
2. Lead the power cable from the circuit breaker to a "ON/OFF" double bipolar
switch (which having a contact opening at least 3mm in all poles) outside the
bathroom, then lead a cable connected to terminal block inside the unit
(fig.3a)
3. Insert the cable through core hitch 'A' for side entry or hole 'B' below the
Back base for wall embedded cable (fig.3b).
4. Connect the cable to Terminal Block and fully tighten them as follow:
BROWN or RED for LIVE (L)
BLUE or BLACK for NEUTRAL (N)
GREEN or Green/Yellow for EARTH ( )
5. Check the Wiring connection is tighten and correct then close the Front
Cover. When close back the Front Cover, please take note the below
procedure:
- To ensure the correct position, turn the Temperature VR Knob Insert to OFF
position as shown in fig.4a. (At the Heater Base)
- To install the Front Cover, turn the Temperature Control Knob to OFF
position to align with the VR Knob Insert as shown in fig.4b. (At the Front
Cover)
** For With Pump models, the same align procedure is apply to both Pump
Speed VR Insert and Pump Knob.
6. Fix back the screw A.
Electrical
connection
IMPORTANT :
THE HEATER TANK MUST BE FILLED UP WITH WATER BEFORE TURN ON THE
ELECTRICITY SUPPLY. THIS IS TO PREVENT ANY DRY BURNT DAMAGE TO THE
HEATING ELEMENT.
1. Turn on the water supply and Stop Valve, then wait until the water flow
through the Hand Shower or faucets (for Multi-Point model).
2. Switch on the electrical supply and the Green LED (ELCB) lamp will turn
on.
3. Turn the Temperature Control Knob to 'ON', the Red LED (HEATER) lamp
will turn on, the hot water will come out in a few seconds. The higher the
temperature indicator position, the hotter is the shower.
Starting and
testing
4. The shower might not be hot enough even at the 'MAX' position if the
incoming water supply from the mains is too cold or the flow too high. In this
case, you can adjust the water inflow in order to get the desired showering
temperature.
5. Check the Built-in ELCB as follow :
- Press the " TEST " Button, the unit should trip and cut off the power supply,
all LED lamps should light off.
- Press the " RESET " Button, the unit should resume back normal function,
Green LED lamp should light on.
If the above mentioned procedure prevail, the ELCB is functioning in normal
condition.
6. If Shower accessory is avaiable, the height and the direction of the Shower
Holder is adjustable. By depress the release button and
slide the Shower
Holder to the desired position. Move the Handshower to the desired angle. A
ratchet mechanism in the Shower Holder will holds the Handshower in the
selected position (fig.5).
7. It is not necessary to turn the Temperature Control Knob to 'OFF' position
when the Heater is not in use.
8. SWITCH OFF the electrical power supply after shower.
FOR PUMP MODEL :
9. Turn on the Pump Speed Control Knob to test run the pump. If the shower
is not hot enough, you can adjust the Knob to reduce the pump speed until
you get the desired shower temperature.
LOW PRESSURE BOOSTER :
10. Thanks to this Innovative " Low Pressure Booster " technology, now even
at a very low water pressure area (too low to activate the flow switch), the
users still can enjoy a pleasant showering experience by just pressing this
"Low Pressure Booster" button to direct activate the Pump, procedure are as
follows :
- Turn on the power supply, turn on the water tap, press the "Low Pressure
Booster" button and hold it for a few second to built up the pressure (fig.6),
after that release the button and the Pump motor should be running by itself.
- When turn off the water supply, the Pump motor will automatic stop, to
activate the Pump motor again, follow above mentioned steps
IMPORTANT:
If the incoming water pressure is sufficient to activate the Flow switch, IT IS
NO NEED TO PRESS THIS " LOW PRESSURE BOOSTER " Button. Just
follow the step 9 for the adjustment of the Pump Speed.
This product is equipped with a SINGLE POLE ELCB, which in case
of mishap will protect the user from leakage current ONLY if the Line
and Neutral cable have been connected correctly
(i.e. NOT INVERTED)
7
MAINTENANCE
B G
N V B G
Read the section 'WARNING' first.
(For ELCB models only) (fig.7) (This procedure is highly recommended.)
Turn on the electricity and water supply, the Green ELCB lamp will light up. If
the Temperature Control Knob is in 'ON' position, the Red HEATER lamp will
light up also. Press the ELCB Test Knob, the ELCB and HEATER lamp should
go off. Press the Reset Knob to resume back the electricity supply.
If the ELCB or HEATER lamp does not go off when you press the ELCB Test
Knob, SWITCH OFF the mains supply and contact your sales agent for repair.
Special skill is required for repair. NEVER try to repair the unit by yourself.
Test the “ELCB”
regularly
Do not use thinner, alcohol, petrol or any other organic solutions to clean the
set, use only a damp cloth with mild detergent.
Cleaning
precaution
There are two filter located at the stop valve, one is Mesh Filter (installed at
the incoming water supply), another one is the built-in Filter as shown in
fig.8a.
Clean the Mesh Filter regularly to prevent blockage. Remove the built-in Filter
by turn it anti clockwise as shown in fig.8a. Take out the Filter and flush it with
water to remove any trapped sediments. (as shown in fig.8b)
Clean the filter
regularly
Turn and remove the Mist Column Ring with plier and then remove screw and
take out the Spray Ring for Cleaning purpose. Be careful when fixing back, it
must be tight fit, otherwise water will leak (fig.9a)
This innovative adjustable Handshower has 5 different spray actions ( STAN -
DARD, JUMBO , SOOTHE , MIX and MASSAGE ). The actions are described
as fig.9b.
Note : The specification, actual product's cosmetic design and accessories parts shown
are correct at the time of printing and may be subjected to change without prior notice.
Shower Accessories parts are optional for Multi-Point Models.
Shower head
cleaning
i ii
DESCRIPTION OF WATER HEATER
MÔ TẢ MÁY NƯỚC NÓNG TRỰC TIẾP
VN GB
INSTALLATION DIAGRAM
SƠ ĐỒ LẮP ĐẶT MÁY NƯỚC NÓNG
2c
PRESS BUTTON
FOR HEIGHT
ADJUSTMENT
NHẤN NÚT ĐỂ
ĐIỀU CHỈNH
CHIỀU CAO
FLEXIBLE ANGLE
ADJUSTMENT
ĐIỀU CHỈNH GÓC
5 SPRAY PATTERNS
SELECTION
LỰA CHỌN 5
CHẾ ĐỘ PHUN
Slider Rail Bar
Ống trượt
Soap Tray
Khay xà phòng
Terminal cover
Nắp che
Screw
Vít bắt
Mounting terminal
Đầu giữ ống
Shower Holder
Giá đỡ vòi sen
Flexible Hose
Ống mềm
Hand Shower
Vòi sen
Wall Plug
Nở nhựa
Terminal Spacer (Optional)
Đệm đầu giữ ống
WALL
TƯỜNG
For White Accessories.
Bộ vòi sen nhựa trắng
2d
Mesh filter
Lưới lọc
(*)
Water
Outlet
Đầu
nước ra
Water
Inlet
Đầu
nước vào
Serviceable 1/2” Socket
Đầu nối nước vào 1/2”
(*) Only for BME 6022E only
(*) Chỉ có ở kiểu BME6022
Screw A
Vít A
185.5
292
2b
PRESS BUTTON FOR
HEIGHT ADJUSTMENT
NHẤN NÚT ĐỂ ĐIỀU
CHỈNH CHIỀU CAO
FLEXIBLE ANGLE
ADJUSTMENT
ĐIỀU CHỈNH GÓC
5 SPRAY
PATTERNS
SELECTION
LỰA CHỌN 5
CHẾ ĐỘ PHUN
Slider Rail Bar
Ống trượt
Soap Tray
Khay xà phòng
Terminal cover
Nắp che
Screw
Vít bắt
Mounting terminal
Đầu giữ ống
Shower Holder
Giá đỡ vòi sen
Flexible Hose
Ống mềm
Hand Shower
Vòi sen
Wall Plug
Nở nhựa
WALL
TƯỜNG
For Chrome Accessories.
Bộ vòi sen mạ Crôm
Cold water supply
Cấp nước vào
Wash Basin
Chậu rửa
Shower Bath
Vòi sen
Long Bath
Bồn tắm
Water Heater
Máy nước nóng
Pressure Relief
Valve
Van an toàn
2a
Multi-Point only
Chỉ áp dụng với kiểu máy Multi-Point
1
2
3
4
7
6
8
12
113
14
15
16
17
18
2
3
4
5
7
8
9
10
11 1932 20 21 22 23
19 20 21 22 23
19 20 21 22 23
24252627283031242627
27
26
29
28
283033
1
31
Saluran
Air Masuk
M
A
X
M
A
X
OFF
M
A
X
OFF
M
A
X
M
A
X
OFF
M
A
X
OFF
iii iv
3a 3b
Brown or Red = Live(L)
Blue or Black = Neutral (N)
Green or Green/Yellow = Earth ( )
Nâu hoặc Đỏ = dây Pha (L)
Xanh lục hoặc Đen = dây Trung tính (N)
Xanh lá hoặc/Xanh-Vàng = dây Đất
Fuse Distributor Board Miniature Circuit Breaker (MCB)
Cầu dao chính
ON/OFF Double Pole Switch
Công tắc 2 cực
FUSE
ON/OFF
Double PVC cable
Cáp mềm 2 vỏ PVC
Cable/ Cáp nguồn
A
B
L
N
E
Side Entry
Lối vào bên sườn
Embedded Entry
Lối vào phía sau
4a 4b
Pump Speed
VR Knob Insert
Vòng đệm điều chỉnh bơm
Temperature
VR Knob Insert
Vòng đệm
điều chỉnh nhiệt độ
Heater Base
Bên trong thân máy
OFF
OFF
Position this way
Quay về hướng này
Temp.Control Knob
Núm điều chỉnh nhiệt độ
Front Cover
Nắp mặt trước
Position this way
Quay về hướng này
Position this way
Quay về hướng này
Position this way
Quay về hướng này
Pump Knob
Núm điều chỉnh bơm
5 7
9a
9b
6
TEST
LOW PRESSURE
BOOSTER
KHỞI ĐỘNG BƠM
ÁP LỰC THẤP
Release Button
Nhấn nút
để điều chỉnh
độ cao
Mist Column Ring
Khoen gài
Spray Ring
Vòng phun
Spray Ring Reatainer
Vành giữ vòng phun
MASSAGE SPRAY
PHUN MÁT-XA
MIX SPRAY
PHUN PHỐI HỢP
STANDARD SPRAY
PHUN TIÊU CHUẨN
SOOTHE SPRAY
PHUN ÊM DỊU
JUMBO SPRAY
PHUN TIA LỚN
RESET
LOW
PRESSURE
BOOSTER
FLOW REGULATOR
CHỈNH LƯU LƯỢNG
FILTER
TẤM LỌC
OPEN
CHIỀU MỞ
CLOSE
CHIỀU ĐÓNG
MESH FILTER
LƯỚI LỌC
8a
FILTER UNIT CLEANING
RỬA SẠCH TẤM LỌC
VÀ LƯỚI LỌC
8b
Posisikan seperti ini
M
A
X
M
A
X
OFF
M
A
X
OFF
M
A
X
M
A
X
OFF
M
A
X
OFF
M
A
X
M
A
X
OFF
M
A
X
OFF
v vi
VN GB
TABLE 1 - ELECTRICAL LOADING TABLE
BẢNG 1 - BẢNG LỰA CHỌN KÍCH THƯỚC DÂY
Conductor Size ( csa )Voltage
(AC)
Power
(kW)
Current
(A)
mm
2
Conduit Cable Flexible Cable
On/Off
Switch (A)
Fuse /
MCB (A)
240V~
50/60 Hz
230V~
50/60 Hz
220V~
50/60 Hz
3.3 13.8 2.5 7 / 0.67 mm 50 / 0.25 mm 20 16
3.6 15.0 2.5 7 / 0.67 mm 50 / 0.25 mm 20 20
4.0 16.7 2.5 7 / 0.67 mm 50 / 0.25 mm 32 20
5.0 20.8 4.0 7 / 0.85 mm 56 / 0.30 mm 32 32
3.0 13.0 2.5 7 / 0.67 mm 50 / 0.25 mm 20 16
3.3 14.3 2.5 7 / 0.67 mm 50 / 0.25 mm 20 16
4.0 17.4 2.5 7 / 0.67 mm 50 / 0.25 mm 32 20
5.0 21.8 4.0 7 / 0.85 mm 56 / 0.30 mm 32 32
2.4 10.9 2.5 7 / 0.67 mm 50 / 0.25 mm 20 16
3.5 15.9 2.5 7 / 0.67 mm 50 / 0.25 mm 20 20
4.5 20.5 2.5 7 / 0.67 mm 50 / 0.25 mm 32 32
5.5 25.0 4.0 7 / 0.67 mm 56 / 0.30 mm 32 32
6.0 27.3 4.0 7 / 0.85 mm 56 / 0.30 mm 32 32
Pump Motor
Thermostat
Main Supply
220-240V ~ a.c.
E
Earth
N
L
Neutral
Live
Heating Element
T2
T1
G
ON / OFF Switch
Flow Switch
M2Y
N1
Heater Control
Electronic ELCB,
15mA Sensitivity
G
T1
Triac
T2
ON / OFF Switch
Speed Control
N
L
EP Model
WIRING DIAGRAM MULTI POINT MODEL
Auto Reset
Thermostat
Main Supply
220-240V ~ a.c.
E
Earth
N
L
Neutral
Live
Heating Element
T2
T1
G
ON / OFF Switch
Flow Switch
N1
Heater Control
Electronic ELCB,
15mA Sensitivity
G
T1
Triac
T2
N
L
Manual Reset Thermal
cut out
WIRING DIAGRAM SILENT PUMP MODEL
Thermostat
Main Supply
220-240V ~ a.c.
E
Earth
N
L
Neutral
Live
Heating Element
T2
T1
G
ON / OFF Switch
N1
Heater Control
Electronic ELCB,
15mA Sensitivity
G
T1
Triac
T2
Pump ON / OFF Switch
N
L
N
L
FS
L
Switch
Mode
Power
Supply
Flow Switch
N
Pump
Pump led
Pump
WIRING DIAGRAM DPDT MODEL
WIRING DIAGRAM SINGLE POINT MODEL
Manual
Single Double Action
Thermostat
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
Ariston WITH PUMP User manual
- Type
- User manual
- This manual is also suitable for
Ariston WITH PUMP is an electric instant water heater that provides hot water on demand. It has a built-in pump that ensures a consistent flow of hot water, even in low-pressure situations. The heater has a temperature control knob that allows you to adjust the water temperature to your desired level. It also has a built-in ELCB (Earth Leakage Circuit Breaker) that protects you from electrical shocks. The heater is easy to install and use, and it comes with a 1-year warranty.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Other documents
-
Glacier Bay Tidal Installation guide
-
Redring Bright 9.5kW Multi-Connection Electric Shower Product information
-
ALFI BRAND AB7938-BN User manual
-
-
PULSE Showerspas 1010 Installation guide
-
chewy 253037 User manual
-
Ariel BT-062 Installation guide
-
-
Samsung WA21M8700GV/SV User manual
-