Schluter DHERR1/BW User manual

Brand: Schluter

Model: DHERR1/BW

Type: User manual

INNOVATIVE SOLUTIONS FOR CERAMIC AND STONE TILE

ELECTRIC FLOOR WARMING SYSTEM WITH INTEGRATED UNCOUPLING TECHNOLOGY

Application and Function

6.4 Schluter

-DITRA-HEAT and DITRA-

HEAT-DUO integrate customizable,

comfortable electric floor warming with the

functions of DITRA: uncoupling, waterproofing,

vapor management and support to ensure a

long lasting installation. DITRA-HEAT-DUO

features an integrated thermal break to reduce

impact sound transmission through floor-ceiling

assemblies, reduce heat loss to the substrate,

and improve floor warming response time.

Floor Warming

DITRA-HEAT and DITRA-HEAT-DUO combine

the flexibility of loose heating cables with the

ease of installation of mat systems. Cables

can be placed wherever heat is desired,

without creating height differences in the floor.

Self-leveling compounds are not required to

encapsulate the cables, significantly reducing

installation time and effort.

Sound Control

Controlling impact sound transmission

through floor-ceiling assemblies in multi-story

construction can present challenges, particularly

when ceramic and stone tiles are used. Sound

control materials tend to be compressible and

not all provide adequate support for tile covering

in thin-set applications. DITRA-HEAT-DUO

reduces sound transmission, while supporting

the covering to ensure a lasting installation.

Uncoupling

Tile has been successfully installed for thousands

of years by incorporating an uncoupling layer, or

forgiving shear interface, within the tile assembly.

DITRA-HEAT and DITRA-HEAT-DUO provide

uncoupling through their geometric configuration,

which allows for in-plane movement that

effectively neutralizes the differential movement

stresses between the substrate and the tile,

thus eliminating the major cause of cracking and

delaminating of the tiled surface.

Schluter

-DITRA-HEAT

Waterproofing

DITRA-HEAT and DITRA-HEAT-DUO provide

reliable waterproofing. Their polypropylene

composition protects the substrate from

moisture penetration, which is particularly

important in today’s building environment where

most substrates are moisture-sensitive.

Vapor Management

The free space on the underside of

DITRA-HEAT and DITRA-HEAT-DUO provide a

route for excess moisture and vapor to escape

from the substrate that could otherwise cause

damage to the tile covering above. Thus, DITRA-

HEAT and DITRA-HEAT-DUO effectively manage

moisture beneath the tile covering.

Support/load distribution

When placed on a solid foundation, columns

or pillars can support tremendous loads. The

same physical principle applies to DITRA-

HEAT and DITRA-HEAT-DUO installations.

Column-like mortar structures are formed

in and between the studs on the surface

of the matting. Loads are transferred from

the tile covering through these column-like

mortar structures to the substrate. Since

DITRA-HEAT and DITRA-HEAT-DUO are virtually

incompressible within the tile assembly, the

advantages of uncoupling are achieved without

sacrificing point load distribution capabilities.

1/4"

(5.5 mm)

6.4 Schluter

-DITRA-HEAT

6.4 Schluter

-DITRA-HEAT-DUO

5/16"

(8 mm)

Schluter

-DITRA-HEAT

Material Properties and

Areas of Application

DITRA-HEAT is a polypropylene membrane

with a cut-back stud structure and an anchoring

fleece laminated to the underside. The thickness

of the mat, including the stud structure is

1/4" (5.5 mm). DITRA-HEAT-DUO is a

polypropylene membrane with a cut-back stud

structure and a thermal break anchoring fleece

laminated to the underside. The thickness of the

mat, including the stud structure and thermal

break fleece is 5/16" (8 mm). Polypropylene is

not UV-stable in the long term; the product must

not be stored in places with prolonged exposure

to direct sunlight.

The DITRA-HEAT and DITRA-HEAT-DUO

mattings do not rot and are inert, non-toxic,

and physiologically safe. The material is highly

resistant to solutions containing salts, acids, and

alkalis, as well as many organic solvents, alcohols,

and oils. Resistance to specific stresses

can be provided if concentration,

temperature, and exposure time are known.

DITRA-HEAT and DITRA-HEAT-DUO are

waterproof and minimize the transmission of

vapor.

Schluter

-DITRA-HEAT-DUO offers the same

functions as the Schluter

-DITRA-HEAT

membrane, but also features an integrated

thermal break in the form of a thicker bonding

fleece. The thermal break reduces impact sound

transmission through floor-ceiling assemblies,

reduces heat loss to the substrate, and improves

the floor warming response time at the standard

three stud cable spacing.

When tested according to ASTM E2179, an

assembly of DITRA-HEAT-DUO and 12" x 12"

porcelain tile installed and grouted with cement-

based setting materials produced an increase

in impact insulation class (ΔIIC) of 20 to a

concrete slab floor-ceiling assembly (Test Report

NGC 7016078). The same basic assembly

tested according to ASTM C627 reached a

classification of “Light” in accordance with the

“TCNA Handbook for Ceramic, Glass, and Stone

Tile Installation,” defined as suitable for “light

commercial use in office space, reception areas,

kitchens, and bathrooms” (Test Report TCNA-

455-15 Test #1).

In laboratory testing, DITRA-HEAT-DUO

reduced floor warming response time from 68°F

(20°C) to 78°F (25.5°C) by approximately 80%

(90 minutes) compared to DITRA-HEAT over

a concrete substrate. Wood substrates act

as insulators and typically do not pose the

same challenges as concrete substrates. In

the same laboratory testing, DITRA-HEAT-DUO

only reduced floor warming response time from

68°F (20°C) to 78°F (25.5°C) by approximately

20% (5 minutes) compared to DITRA-HEAT

over a plywood substrate. Schluter

-DITRA-

HEAT-E-HK heating cables were spaced at

three studs in all of the above tests. Results

above are based upon laboratory testing. Actual

results may vary depending on various factors,

including concrete substrate thickness, concrete

substrate temperature, room temperature, heat

losses, etc.

DITRA-HEAT and DITRA-HEAT-DUO have been

evaluated according to the "Standard Method

for the Testing and Evaluation of Volatile Organic

Chemical Emissions from Indoor Sources Using

Environmental Chambers, Version 1.1" for

California Specification 01350 and found to

comply with the VOC requirements. California

Specification 01350 is referenced by various

green building standards and rating systems.

DITRA-HEAT-E-HK are twisted pair heating

cables designed for integration with the DITRA-

HEAT and DITRA-HEAT-DUO uncoupling

membranes in interior floor warming applications.

The cables can be installed without returning

to the thermostat and produce virtually zero

electromagnetic fields.

DITRA-HEAT-E-WiFi/-RT/-R are digital

thermostats to control the DITRA-HEAT-E-HK

heating cables (either 120 V or 240 V). The

thermostats feature a built-in Class A ground

fault circuit interrupter (GFCI) with indicator light.

The DITRA-HEAT-E-WiFi programmable WiFi

thermostat features LCD touchscreen controls

and comes with a pre-set schedule, but may be

adjusted to fit any schedule. When connected

to WiFi, the thermostat provides convenient

monitoring and adjustment of the floor warming

system via the web or mobile app. The DITRA-

HEAT-E-RT programmable thermostat features

LCD touchscreen controls and comes with

a pre-set schedule, but may be adjusted to

fit any schedule. The DITRA-HEAT-E-R non-

programmable version features a simple on/

off function. Multiple heating cables may be

connected to the thermostats, up to the total

heating load limit of 15 amps. The DITRA-HEAT-

E-RR power module may be used in conjunction

with the DITRA-HEAT-E-RT/-R thermostats

when the heating load exceeds 15 amps (e.g.,

in large floor applications). A floor temperature

sensor is included.

Two floor temperature sensors are provided

– one with the DITRA-HEAT-E-WiFi/-RT/-R

thermostats and one with the DITRA-HEAT-

E-HK heating cables. Both floor temperature

sensors are installed within the tile assembly. One

sensor is connected to the thermostat, while the

other sensor is stored in the thermostat electrical

box, but not connected to the thermostat. The

second sensor can easily be connected to the

thermostat to replace the first sensor in case of

damage.

Suitable Substrates

Wood

All wood materials, including OSB, plywood,

and framing members, are subject to expansion,

contraction, bending, and deflection as a result

of changes in moisture content and loading.

Further, these deformations fluctuate over the life

of the building structure.

Concrete

There are various challenges associated with

the installation of hard surface coverings on

concrete substrates. To begin, the coefficient of

thermal expansion of concrete is close to twice

that of ceramic tile. Additionally, tile contractors

are often expected to install tile over young

concrete (concrete cured less than 28 days).

However, rigid surface coverings installed

over young concrete are susceptible

to damage as a result of shrinkage during

curing. Pre-stressed/post-tensioned

concrete slabs are also commonplace

in today’s construction environment.

Although pre-stressing is used to help control

deflections in concrete structures, these slabs are

still subject to deformations caused by changes

in moisture, temperature, and loading. Many

concrete slabs on or below grade are subject to

moisture migration, which can be problematic.

Furthermore, these structures experience the

same deformations as stated above.

Gypsum

Bonding ceramic or stone tiles directly

to gypsum concrete substrates is generally

considered questionable or not recommended.

The challenges associated with gypsum-based

underlayments include the requirement of an

extended drying period before installing tile and

continued sensitivity to the reintroduction of

moisture throughout the life of the installation.

In addition, since the coefficient of thermal

expansion of gypsum concrete is substantially

greater than that of ceramic tile, shear stresses

caused by temperature fluctuations can result

in delamination or cracking of the tile covering.

Note: DITRA-HEAT and DITRA-HEAT-DUO may

be installed over existing vinyl floors (no cushioned

or perimeter bonded vinyl). However, various

steps must be taken to ensure a successful

installation. Please refer to the Schluter

-DITRA-

HEAT Installation Handbook for details.

Installation

For complete installation guidelines

and warranty criteria, please contact

Schluter-Systems (USA: 800-472-4588;

Canada: 800-667-8746) to receive a copy of the

Schluter

-DITRA-HEAT Installation Handbook.

To download a PDF version of the handbook or

to view the installation video online, please visit

www.schluter.com.

All substrates must be clean, even, and load

bearing. Bond inhibiting surfaces must be

removed prior to the application of DITRA-HEAT

and DITRA-HEAT-DUO.

Schluter

-DITRA-HEAT

Note: Type, thickness, and format of the tile or

stone surface covering must be suitable for the

intended application. Minimum tile format is 2" x

2" (5 cm x 5 cm).

Due to airspace within the assembly, tile or

stone coverings installed over DITRA-HEAT-

DUO membranes may have a hollow sound

when they are walked upon with hard shoes or

tapped with a hard object.

Movement Joints

DITRA-HEAT and DITRA-HEAT-DUO do not

eliminate the need for movement joints, including

perimeter joints, within the tiled surface. Please

refer to the Schluter

-DITRA-HEAT Installation

Handbook for movement joint placement

guidelines.

Wood Underlayment

In some applications, adding a layer

of plywood or OSB before installing

DITRA-HEAT or DITRA-HEAT-DUO and the

ceramic or stone tile covering is required to

reduce deflection and curvature of the

sheathing between the joists. Please refer to

the Schluter

-DITRA-HEAT Installation

Handbook for plywood/OSB underlayment

installation guidelines.

Thin-Set Facts

Schluter

-Systems offers thin-set mortars

designed for use with Schluter

membranes

and boards. All Schluter

-Systems’ thin-set

mortars, including the ALL-SET™ and FAST-

SET™ modified varieties, can be used to set

tile over Schluter

-DITRA, DITRA-HEAT, KERDI,

KERDI-BOARD non absorptive substrates. If

Schluter

thin-set mortars are not used, we

require unmodified thin-set mortar when setting

ceramic or porcelain tile over DITRA-HEAT.

Question: Can ceramic tile, including porcelain

tile, be set on DITRA-HEAT or DITRA-HEAT-

DUO with unmodified thin-set mortar?

Answer: YES. In fact, we recommend it.

Here’s why: Portland cement-based unmodified

thin-set mortars are dependent

upon the presence of moisture for hydration

in order to gain strength. Since DITRA-HEAT

and DITRA-HEAT-DUO are impervious, they

do not deprive the mortar of its moisture.

This allows the cement to properly hydrate,

resulting in a strong, dense bond coat. In

fact, after the mortar has reached final set

(usually within 24 hours), unmodified

thin-set mortars achieve higher strengths when

cured in continually moist conditions.

Question: Can ceramic tile, including porcelain

tile, be set on DITRA-HEAT and DITRA-HEAT-

DUO with latex-modified thin-set mortar?

Answer: In general, we DON’T recommend it.

Here’s why: Latex-modified mortars must

dry for the polymers to coalesce and form

a hard film in order to gain strength. When

sandwiched between two impervious materials

such as DITRA-HEAT or DITRA-HEAT-DUO

and ceramic tile, including porcelain tile, drying

takes place very slowly through the open joints

in the tile covering. [According to the TCNA

Handbook for Ceramic, Glass, and Stone Tile

Installation, this drying period can fluctuate from

14 days to over 60 days, depending on the

geographic location, the climatic conditions,

etc.]. Therefore, extended cure times could be

required before grouting if using modified thin-

set mortars between DITRA-HEAT or DITRA-

HEAT-DUO and ceramic tile, including porcelain

tile. If extended cure times were not observed,

the results could be unpredictable.

Question: Can Schluter ALL-SET™ and

Schluter FAST-SET™ modified thin-set mortars

be used to set tile over Schluter boards and

membranes?

Answer: Yes. All Schluter

thin-set mortars,

including the ALL-SET™ and FAST-SET™

modified varieties can be used to set tile over

DITRA, DITRA-HEAT, KERDI, KERDI-BOARD

non absorptive substrates.

Question: How is this possible?

Answer: The key is predictability. Schluter

Systems’ modified thin-set mortars have been

specifically formulated to set and gain strength in

a timeframe that fits typical installation practice,

even when sandwiched between Schluter

membranes or boards and porcelain tile. The

proportions of cement, water-retention agents,

polymers, and other components in the mixtures

were balanced to ensure that extended dry times

are not required. This was validated through

both laboratory and practical testing. Now, the

installer can select from either unmodified or

modified thin-set mortar to install tiles within our

systems according to his or her preference.

Question: Why did Schluter Systems change its

position on thin-set mortar?

Answer: We haven’t changed our position

on thin-set mortar use within our systems.

Developing our own setting materials has given

us the ability to guarantee consistently positive

results. And since we control the formulas, we

can be sure no changes will be made that have

a negative impact on setting times and strength

gain in these environments.

Question: Does this mean I can use other

manufacturers’ modified thin-set mortars to

install tile over Schluter boards and membranes?

Answer: No. Our position on thin-set mortar use

within our systems in general has not changed.

We have no control over the formulation of other

manufacturers’ products and therefore cannot

guarantee consistently positive results with their

modified thin-set mortars.

Question: Can I still use other manufacturers’

unmodified thin-set mortars to install tile over

Schluter boards and membranes?

Answer: Yes. We still warrant the use of

unmodified thin-set mortar meeting ANSI A118.1

to install tile within our systems because we

have confidence in the performance of this

product category. This is based on the science

of cement hydration and years of positive testing

and field experience.

Please note, if Schluter

thin-set mortars are

used with Schluter membranes an extended

system warranty is available.

Additional Notes:

Remember, the type of mortar used to apply

DITRA-HEAT or DITRA-HEAT-DUO depends on

the type of substrate. The mortar must bond to

the substrate and mechanically anchor the fleece

on the underside of the matting. For example,

bonding DITRA-HEAT or DITRA-HEAT-DUO to

wood requires latex-modified thin-set mortar.

Additionally, all mortars (modified and unmodified)

have an acceptable temperature range that must

be observed during application and curing.

Pre-mixed thin-set mortars and mastics are not

suitable for use in conjunction with DITRA-HEAT

and DITRA-HEAT-DUO.

Schluter

-DITRA-HEAT

Testing and Certifications

Uncoupling Membrane

The method used to establish the overall performance of a tile assembly under loading is the ASTM C627 “Standard Test Method for Evaluating

Ceramic Floor Tile Installation Systems Using the Robinson Type Floor Tester.” The assembly is tested in cycles using a loaded, revolving carriage.

Load, wheel hardness, and number of revolutions vary with each cycle. Once a specified level of damage is exceeded, the test is stopped. The TCNA

Handbook for Ceramic, Glass, and Stone Tile Installation assigns performance levels to an assembly based on the number of cycles successfully

completed. The ratings include residential, light, moderate, heavy, and extra heavy, in order of improving performance.

Assembly Notes:

1. All plywood and OSB subﬂoors were 23/32" (3/4" nom.) -thick; 11/32" (3/8" nom.)-thick OSB underlayment added for carrara marble test

2. Modiﬁed thin-set mortar (ANSI A118.11) to bond membrane to plywood and OSB.

3. Unmodiﬁed thin-set mortar (ANSI A118.1) to bond membrane to concrete

4. Unmodiﬁed thin-set mortar (ANSI A118.1) to bond tile to membrane

5. High Performance Cement Grout (ANSI A118.7)

Waterproofing

DITRA-HEAT and DITRA-HEAT-DUO matting provide reliable waterproofing in interior applications. The products have been found to meet or exceed

the requirements of the American National Standard Specifications for Load Bearing, Bonded, Waterproof Membranes for Thin-set Ceramic Tile and

Dimension Stone Installation A118.10.

DITRA-HEAT:

• ICC-ES Report No. ESR-2467

• ICC-ES PMG Report No. PMG-1204

• DITRA-HEAT: U.S. Pat. No. 8,950,141, and U.S. DES. PAT. No. D706459 Canada D Schluter Systems L.P. and other patents pending

DITRA-HEAT-DUO:

• ICC-ES Report No. ESR-2467

• ICC-ES PMG Report No. PMG-1204

• Patent pending

The product has been found to meet or exceed the requirements of the American National Specifications for Bonded Sound Reduction Membranes

for Thin-Set Ceramic Tile Installation A118.13.

Sound control

DITRA-HEAT-DUO reduces impact sound transmission through floor-ceiling assemblies and supports the covering to ensure a lasting installation.

DITRA-HEAT-DUO has been found to meet or exceed the requirements of the American National Specifications of Bonded Sound Reduction

Membranes for Thin-Set Ceramic Tile Installation A118.13.

Report Number

Substrate

Joist Spacing

Tile Rating

Schluter

-DITRA-HEAT

TCNA-415-13 OSB 19.2" o.c.

12" x 12"

porcelain

Extra Heavy

TCNA-415-13 OSB 24" o.c.

12" x 12" carrara

marble

Light

TTMAC-

UFT09-2013

Concrete N/A

12" x 12"

porcelain

Moderate

TCNA-415-13 Concrete N/A 2" x 2" porcelain Light

Schluter

-DITRA-HEAT-DUO

TCNA-455-15 (1) Concrete N/A

12" x 12"

porcelain

Light

TCNA-455-15 (2) Concrete N/A 2" x 2" porcelain Residential

TNCA-455-15 (3) Concrete N/A 12" x 12" marble Light

TCNA-455-15 (4) Plywood 19.2" o.c.

12" x 12"

porcelain

Light

Report Number

Test Substrate Tile Results

Schluter

-DITRA-HEAT-DUO

NGC 7016078 ASTM E2179 Concrete 12" x 12" porcelain ΔIIC = 20

IN17-007 ASTM E492 Concrete* 12" x 12" porcelain IIC = 50

*8" -thick slab, no ceiling below

Schluter

-DITRA-HEAT

Product

Test Method

Performance

Schluter

-DITRA-HEAT

ASTM E96*

0.21 perms

Schluter

-DITRA-HEAT-DUO 0.48 perms

*Using the water method at 73ºF (23ºC) and 50% RH

6.4 Schluter

-DITRA-HEAT Uncoupling and waterproofing membrane

Item No.

Item Dimensions

DH5 12M Roll 3' 2-5/8" x 41' 10-3/4" = 134.5 ft

(0.98 m x 12.76 m = 12.5 m

)

DH5 MA Sheet 3' 2-5/8" x 2' 7-3/8" = 8.4 ft

(0.98 m x 0.80 m = 0.78 m

)

6.4 Schluter

-DITRA-HEAT-DUO Uncoupling and waterproofing membrane with thermal break

Item No.

Item Dimensions

DHD8 10M

Roll

3' 2-5/8" x 33' 6-1/2" = 108 ft

(0.98 m x 10.20 m = 10 m

)

DHD8 MA

Sheet

3' 2-5/8" x 2' 7-3/8" = 8.4 ft

(0.98 m x 0.80 m = 0.78 m

)

Product Item Numbers

U.S. Pat. No. 8,950,141, and U.S. DES. PAT. No. D706459

Canada D Schluter Systems L.P. and other patents pending.

Patent pending

IIC

Impact Insulation Class (IIC) is a rating that characterizes the levels of impact noise transmitted through different floor-ceiling assemblies. It can be

used by architects, builders, and specification and code authorities for acoustical design purposes in building constructions. The rating increases as

the impact sound attenuation of the floor-ceiling assembly increases.

IIC is determined according to ASTM E492 and ASTM E989. The ASTM E492 test method is a laboratory measurement of impact sound transmission

through floor-ceiling assemblies using a standardized tapping machine. The results from this test are then used to calculate a single-number rating per

ASTM E989 that is called impact insulation class.

Delta IIC

Delta Impact Insulation Class (ΔIIC) is a rating that characterizes the reduction in impact noise transmitted through a concrete floor by the addition of

a floor-covering assembly. It can be used to compare the effectiveness of different floor-coverings over concrete and help select different products

and/or systems for acoustical design purposes in building constructions.

ΔIIC is determined according to ASTM E2179. A floor-covering assembly is installed over a standard concrete slab and the IIC of the entire assembly

is determined per ASTM E492 and ASTM E989 as explained above. The ΔIIC rating is obtained by subtracting 28 (the IIC of the concrete slab) from

the IIC of the entire assembly.

Vapor Management

The free space under the DITRA-HEAT and DITRA-HEAT-DUO mattings allow the substrate to breathe, while the material composition provides for a

very low water vapor permeance, which prevents any significant vapor intrusion in the tile assembly from below.

DITRA-HEAT and DITRA-HEAT-DUO effectively manage vapor and prevent damage to the tile covering as a result.

Heating Cables

The DITRA-HEAT-E-HK heating cables sets are certified or listed to the following standards and usage:

• CAN/CSA-C22.2 No. 130-03 "Requirements for Electrical Resistance Heating Cables and Heating Device Sets" under usage markings GXW

for general use (G) with a wet rating (W), but specifically (X) for floor embedded indoor floor warming applications.

For products bearing the cCSAus certification mark:

• UL 1673 "Electric Space Heating Cables" for installation in poured masonry floors within enclosed structures.

For products bearing the cULus certification mark:

• UL 1683 "Outline of investigation for Electric Heating Products For Installation Under Floor Coverings"

Thermostat

DITRA-HEAT-E-WiFi thermostat WiFi radio chip authorized by the FCC (USA) and IC (Canada) under the following numbers:

• FCC ID.................AZY-HF-LPT200

• IC ID....................12243A-HFLPT2001

The DITRA-HEAT-E-WiFi/-RT/-R digital thermostats are UL listed according to the following standards:

• UL 60730-1 “Automatic Electrical Controls for Household and Similar Use – Part 1: General Requirements”

• UL 60730-2-9 “Automatic Electrical Controls for Household and Similar Use – Part 2-9: Particular Requirements for Temperature Sensing

Controls”

• CSA E60730-1:13 “Automatic Electrical Controls for Household and Similar Use – Part 1: General Requirements”

• CSA E60730-2-9 “Automatic Electrical Controls for Household and Similar Use – Part 2-9: Particular Requirements for Temperature Sensing

Controls”

• UL 943 4th ed. “Ground-Fault Circuit Interrupters”

• CSA C22.2 No. 144.1-06 “Ground-Fault Circuit Interrupters”

Power Module

The DITRA-HEAT-E-RR power module is certified or listed to the following standards:

• Listed to UL 60730-1/ UL 60730-2-9 (Thermostat); 943 4th edition (GFCI)

• Certified to CSA E60730-1/ CSA E60730-2-9 (Thermostat); C22.2 No. 144.4-06 (GFCI)

Schluter

-DITRA-HEAT

Schluter

DITRA-HEAT-E-HK-RK is a repair kit for

DITRA-HEAT-E-HK heating cables. The kit contains

all the material to replace one section of heating

cable (gray section) up to 10" (25 cm) long or less in

the event of damage, such as cuts by other trades

during installation.

Schluter

-DITRA-HEAT-E-HK-SK is a splice kit for

DITRA-HEAT-E-HK heating cables. The kit contains

all the material to replace one factory splice of the

heating cable.

Please contact Customer Service for ordering

information.

WARNINGS

Do not use either the repair kit or the splice kit

to splice different heating cables together. The

kits are only intended for making repairs to a

single DITRA-HEAT-E-HK heating cable.

Schluter

-DITRA-HEAT-E-HK-RK Heating Cable Repair Kit and Schluter

-DITRA-HEAT-E-HK-SK Heating

Cable Splice Kit

Repairs must only be made by a qualified electrician

and in accordance with the Schluter

-DITRA-HEAT

Repair Procedure, the National Electric Code (USA)

or Canadian Electric Code Part I (CAN) and all

applicable local electrical and building codes. Failure

to follow these Repair Procedure instructions and

applicable codes may result in personal injury or

property damage or failure of the repair or splice.

Never cut the heating cable. The heating cable

cannot be shortened or altered to fit. This could

change the cable resistance and could lead to a fire.

DISCLAIMER:

Any deviation from the Schluter

-DITRA-HEAT

Installation Handbook during initial installation

(including but not limited to damage to the Schluter

DITRA-HEAT-E-HK heating cables) has voided the

Schluter

-DITRA-HEAT Limited System Warranty and

other applicable warranty coverage. WARRANTY

COVERAGE IS NOT REINSTATED UPON REPAIR

OF THE HEATING CABLE.

Schluter Systems is not responsible or liable under

any circumstances for determining the suitability of

a Repair Kit or Splice Kit for the Owner’s intended

purpose.

TO THE EXTENT PERMITTED BY LAW,

SCHLUTER SYSTEMS DISCLAIMS ANY AND

ALL WARRANTIES, REPRESENTATIONS OR

CONDITIONS, EXPRESSED OR IMPLIED,

INCLUDING BUT NOT LIMITED TO THE IMPLIED

WARRANTIES OF MERCHANTABILITY AND

FITNESS FOR A PARTICULAR PURPOSE, AND

ANY AND ALL LIABILITY ARISING FROM REPAIR

SERVICES PROVIDED BY AN ELECTRICIAN.

It is recommended that prior to commencing a

repair, any known deviations from the Schluter

DITRA-HEAT Installation Handbook and/or

applicable codes be corrected.

6.4 Schluter

-DITRA-HEAT-E-HK Heating Cable

Item No.

Heating Cable

Length

Area Covered per Cable Spacing

Total

Power

Avg. Power per Unit Area per Cable Spacing

Current

Regular 3 Stud Alternating 3-2 Stud Regular 3 Stud Alternating 3-2 Stud

(ft) (m) (ft

) (m

) (ft

) (m

) (W)

(Watts/ft

) (Watts/m

) (Watts/ft

) (Watts/m

) (Amps)

Heating Cable (120 V)

DHE HK 120 11 35.3 10.8 10.7 1.0 8.9 0.8 135 12.6 136 15.2 164 1.1

DHE HK 120 16 52.9 16.1 16.0 1.5 13.3 1.2 203 12.7 136 15.2 164 1.7

DHE HK 120 21 70.5 21.5 21.3 2.0 17.8 1.7 270 12.7 136 15.2 164 2.3

DHE HK 120 27 88.2 26.9 26.7 2.5 22.2 2.1 338 12.7 136 15.2 164 2.8

DHE HK 120 32 105.8 32.2 32.0 3.0 26.7 2.5 405 12.7 136 15.2 164 3.4

DHE HK 120 38 124.1 37.8 37.5 3.5 31.3 2.9 475 12.7 136 15.2 164 4.0

DHE HK 120 43 141.1 43.0 42.7 4.0 35.6 3.3 540 12.7 136 15.2 164 4.5

DHE HK 120 51 169.8 51.8 51.4 4.8 42.8 4.0 650 12.7 136 15.2 164 5.4

DHE HK 120 64 212.9 64.9 64.4 6.0 53.7 5.0 815 12.7 136 15.2 164 6.8

DHE HK 120 73 240.2 73.2 72.7 6.8 60.6 5.6 920 12.7 136 15.2 164 7.7

DHE HK 120 83 275.5 84.0 83.3 7.7 69.4 6.5 1055 12.7 136 15.2 164 8.8

DHE HK 120 92 303.0 92.4 91.7 8.5 76.4 7.1 1160 12.7 136 15.2 164 9.7

DHE HK 120 102 336.9 102.7 101.9 9.5 84.9 7.9 1290 12.7 136 15.2 164 10.7

DHE HK 120 113 372.2 113.4 112.6 10.5 93.8 8.7 1425 12.7 136 15.2 164 11.9

DHE HK 120 134 444.0 135.3 134.3 12.5 111.9 10.4 1700 12.7 136 15.2 164 14.2

Heating Cable (240 V)

DHE HK 240 11 35.3 10.8 10.7 1.0 8.9 0.8 135 12.6 136 15.2 164 0.6

DHE HK 240 16 53.1 16.2 16.1 1.5 13.4 1.2 203 12.6 136 15.2 164 0.8

DHE HK 240 21 70.6 21.5 21.4 2.0 17.8 1.7 270 12.7 136 15.2 164 1.1

DHE HK 240 27 88.2 26.9 26.7 2.5 22.2 2.1 338 12.7 136 15.2 164 1.4

DHE HK 240 32 105.8 32.2 32.0 3.0 26.7 2.5 405 12.7 136 15.2 164 1.7

DHE HK 240 38 124.1 37.8 37.5 3.5 31.3 2.9 475 12.7 136 15.2 164 2.0

DHE HK 240 43 141.0 43.0 42.6 4.0 35.5 3.3 540 12.7 136 15.2 164 2.3

DHE HK 240 53 176.3 53.7 53.3 5.0 44.4 4.1 675 12.7 136 15.2 164 2.8

DHE HK 240 64 211.6 64.5 64.0 5.9 53.3 5.0 810 12.7 136 15.2 164 3.4

DHE HK 240 75 248.2 75.7 75.1 7.0 62.6 5.8 950 12.7 136 15.2 164 4.0

DHE HK 240 85 282.1 86.0 85.3 7.9 71.1 6.6 1080 12.7 136 15.2 164 4.5

DHE HK 240 103 339.4 103.4 102.7 9.5 85.6 7.9 1300 12.7 136 15.2 164

5.4

DHE HK 240 129 425.8 129.8 128.8 12.0 107.3 10.0 1630 12.7 136 15.2 164 6.8

DHE HK 240 145 480.5 146.5 145.3 13.5 121.1 11.3 1840 12.7 136 15.2 164 7.7

DHE HK 240 167 551.0 167.9 166.7 15.5 138.9 12.9 2110 12.7 136 15.2 164 8.8

DHE HK 240 183 605.9 184.7 183.3 17.0 152.7 14.2 2320 12.7 136 15.2 164 9.7

DHE HK 240 204 673.8 205.4 203.8 18.9 169.9 15.8 2580 12.7 136 15.2 164 10.7

DHE HK 240 225 744.4 226.9 225.2 20.9 187.7 17.4 2850 12.7 136 15.2 164 11.9

Schluter

-DITRA-HEAT

6.4 Schluter

-DITRA-HEAT-E-KIT

Item No.

DHE K RT 120 40 DHE K RT 120 56

Matting 5 sheets – 42 ft

(3.9 m

) 7 sheets – 58.8 ft

(5.5 m

)

Heating cable 88' 3" – 26.7 ft

(26.9 m – 2.5 m

) 124' 0" - 37.5 ft

(37.8 m - 3.5 m

)

Thermostat

1 – white, programmable touchscreen 1 – white, programmable touchscreen

8.1 Schluter

-KERDI-BAND Waterproofing strips

Item No.

Width Length Thickness

KEBA 100/125/5M 5" – 12.5 cm 16' 5" – 5 m 4 mil

KEBA 100/125/10M 5" – 12.5 cm 33' – 10 m 4 mil

KEBA 100/185/5M 7-1/4" – 18.5 cm 16' 5" – 5 m 4 mil

KEBA 100/250/5M 10" – 25 cm 16' 5" – 5 m 4 mil

KEBA 100/125 5" – 12.5 cm 98' 5" – 30 m 4 mil

KEBA 100/185 7-1/4" – 18.5 cm 98' 5" – 30 m 4 mil

KEBA 100/250 10" – 25 cm 98' 5" – 30 m 4 mil

8.1 Schluter

-KERDI-FLEX Waterproofing strips for use above movement joints

Item No.

Width Length Thickness

FLEX 125/5M 5" – 12.5 cm 16' 5" – 5 m 12 mil

FLEX 250/5M 10" – 25 cm 16' 5" – 5 m 12 mil

FLEX 125/30 5" – 12.5 cm 98' 5" – 30 m 12 mil

FLEX 250/30 10" – 25 cm 98' 5" – 30 m 12 mil

8.1 Schluter

-KERDI-KERECK-F Waterproofing corners

Item No.

Thickness Packaging

KERECK / FI 2 4 mil 2 Inside corners

KERECK / FI 10 4 mil 10 Inside corners

KERECK / FA 2 4 mil 2 Outside corners

KERECK / FA 10 4 mil 10 Outside corners

6.4 Schluter

-DITRA-HEAT-E-WiFi/-RT/-R Digital thermostats with remote floor temperature sensors

Item No.

Description

DHE RT 104/BW

WiFi and touchscreen programmable thermostat in white with floor temperature sensor

DHE RT 102/BW Touchscreen programmable thermostat in white with floor temperature sensor

DHE RT 103/BW Non-programmable thermostat in white with floor temperature sensor

6.4 Schluter

-DITRA-HEAT-E-RR Power module

Item No.

Description

DHE RR 1/BW Power module for use with DHE RT thermostats

6.4 Schluter

-DITRA-HEAT-E-KIT

Item No.

DHE K 120 40 DHE K 120 56

Matting 5 sheets – 42 ft

(3.9 m

) 7 sheets – 58.8 ft

(5.5 m

)

Heating cable 88' 3" – 26.7 ft

(26.9 m – 2.5 m

) 124' 0" - 37.5 ft

(37.8 m - 3.5 m

)

Thermostat

1 – white, Wi-Fi touchscreen programmable 1 – white, Wi-Fi touchscreen programmable

Schluter

-DITRA-HEAT

*Color Codes

To complete the item number, add the

color code (e.g., KERDIFIX / BW).

8.3 Schluter

-KERDI-FIX Adhesive/sealant

Item No.

Description

KERDIFIX / color* Cartridge - 9.81 ﬂ oz (290 ml)

KERDIFIX 100 G Tube - 3.38 ﬂ oz (100 ml)

Schluter

-DITRA-ROLLER Used to embed uncoupling membranes in the bond coat

Item No.

Width

DIRO 14-1/2" (37 cm)

Schluter

-DITRA-HEAT/-DITRA-XL-TROWEL Trowel

Item No. Notch Size Packaging

TRL-DHXL 1/4" x 1/4" (6 mm x 6 mm)

1 unit

TRL-DHXL6 1/4" x 1/4" (6 mm x 6 mm)

6 units

Bright

white

Grey

Schluter

-DITRA-HEAT

Schluter

-DITRA-HEAT System 15-Year Limited Warranty

LIMITED WARRANTY COVERAGE: Subject to the conditions and limitations as stated in this Schluter

-DITRA-HEAT System 15-Year

Limited Warranty (the “Limited Warranty”), Schluter Systems warrants that its Schluter

-DITRA-HEAT System (defined hereafter) will be free from

manufacturing defects and will perform as described in the Schluter

-DITRA-HEAT Installation Handbook and Schluter

-DITRA-HEAT Technical Data

Sheet (collectively, the “Written Materials”

) for a period of fifteen (15) years from the date of purchase when installed and used in accordance with

the terms and conditions of the Written Materials and industry standard guidelines that are not in conflict with the Written Materials in effect at the

time of installation.

In order to receive coverage under this Limited Warranty, the Owner (defined hereafter) must complete and submit the warranty registration card

and completed heating cable tests log to Schluter Systems online at https://www.schluter.com/schluter-us/en_US/registerwarranty or via mail at

the address provided hereafter within fourteen (14) days of installation. It is an installation requirement that the heating cable tests log be completed

by the installer at the time of installation with a copy submitted to Schluter Systems; it is recommended that the Owner retain the original logs. The

heating cable tests log must include results for the following tests: “Test 1: Conductor Resistance,” ‘Test 2: Conductor and Ground Braid Continuity,”

“Test 3: Insulation Resistance,” and “Test 4: Thermostat Floor Temperature Sensor Test.” Failure to conduct these tests and submit the heating

cable tests log will reduce or may void coverage under this Limited Warranty.

In the event the heating cable tests log only includes results for “Test 1: Conductor Resistance,” ‘Test 2: Conductor and Ground Braid Continuity,”

and “Test 4: Thermostat Floor Temperature Sensor Test,” but does not include results for “Test 3: Insulation Resistance,” the applicable warranty

term shall be ten (10) years from the date of purchase. If the heating cable tests log does not include test results for “Test 1: Conductor Resistance,”

‘Test 2: Conductor and Ground Braid Continuity,” and “Test 4: Thermostat Floor Temperature Sensor Test,” such installation does not qualify for

coverage under this Limited Warranty; such installation may instead receive warranty coverage under the Schluter

-DITRA-HEAT and Schluter

DITRA-HEAT-DUO Uncoupling Membrane 10-Year Limited Warranty.

For the purposes of this Limited Warranty, a “DITRA-HEAT System” is defined as Schluter

-DITRA-HEAT or Schluter-DITRA-HEAT-DUO

uncoupling membrane and Schluter

-DITRA-HEAT-E-HK heating cables; “Owner” is defined as the original end user of the property in which the

DITRA-HEAT System is installed; and “Floor Covering Assembly” is defined to include the DITRA-HEAT System, non-reusable flooring surfaces,

and applicable setting and grouting materials.

This Limited Warranty is only applicable to installations in the United States of America and Canada. Schluter Systems is not responsible or liable

under any circumstances for determining the suitability of a DITRA-HEAT System for the Owner’s intended purpose. It is the responsibility of the

Owner to consult with an experienced and professional installer to ensure the suitability of a DITRA-HEAT System, subfloor/substrate and all building

materials in the installation and that the Written Materials are followed properly.

RESOLUTION: If a DITRA-HEAT System is installed and used in accordance with the terms and conditions as described hereinabove and such

DITRA-HEAT System is proven defective within the applicable warranty term, the Owner’s exclusive remedy and the sole obligation of Schluter

Systems, at its election, shall be to (a) reinstall or replace the failed portion of the Floor Covering Assembly or (b) pay an amount not to exceed the

original square foot cost of the installation of the Floor Covering Assembly verified to be defective. Due to conditions beyond the control of Schluter

Systems (e.g., color and shade availability, discontinuation, normal wear and tear), Schluter Systems cannot guarantee or warrant an exact match

to the specific tile, stone, or other flooring materials used in the original installation. In such event, substantially similar materials may be substituted.

This Limited Warranty does not cover the cost of disconnection or installation.

EXCLUSIONS FROM COVERAGE: This Limited Warranty excludes and in no event shall Schluter Systems have any liability for any indirect, special,

incidental, punitive, exemplary, or consequential damages, including lost profits, arising out of or otherwise connected to the failure of DITRA-HEAT

System, regardless of any strict liability or active or passive negligence of Schluter Systems, and regardless of legal theory, whether in contract, tort,

extra-contractual or other. This Limited Warranty further excludes any loss or damage arising out of or otherwise connected to: acts of war, terrorism,

fire, explosion, natural disaster, acts of God, any failure to comply with the Written Materials, inadequate subfloor/substrate, improper preparation

or other failure of subfloor/substrate, faulty or negligent penetration of a DITRA-HEAT System or subfloor/substrate, intentional acts of destruction,

structural failure, misuse of or failure to maintain a DITRA-HEAT System, normal wear and tear, scratches, dents, corrosion or discoloration (whether

caused by excessive heat, chemical cleaning products, abrasive agents or otherwise), efflorescence and shading which are a natural occurrence with

cementitious materials and are not considered a defective condition for the purposes of this Limited Warranty, variations of texture, color or shade

from those on product samples, packaging materials or other marketing materials, or other causes unrelated to a DITRA-HEAT System (e.g. excess

point loading, overvoltage). This Limited Warranty excludes exterior applications, unless specifically approved in writing on a case by case basis

by the Schluter Systems Technical Services Director. Schluter

DITRA-HEAT™-E thermostats are specifically excluded from coverage under this

Limited Warranty; warranty coverage for Schluter

DITRA-HEAT™-E thermostats are limited and subject to the Schluter-DITRA-HEAT Thermostat

3-Year Limited Warranty. Any substitution of a non-Schluter Systems product for a Schluter Systems component in a DITRA-HEAT System voids

this Limited Warranty.

If there are any conflicting terms between any Written Materials, the most recently updated document shall be deemed to control.

Schluter

-DITRA-HEAT

This Limited Warranty is conditioned and will be considered null and void and Schluter Systems will have the right to refuse any claims if: (a) a DITRA-

HEAT System has been improperly stored or installed, (b) any component comprising a DITRA-HEAT System has been altered or otherwise modified

in any way, (c) a DITRA-HEAT System is subject to abusive or abnormal use, lack of maintenance, or used in a manner other than that for which

the DITRA-HEAT System was designed or in any way contrary to the Written Materials, (d) the nameplate numbers (electrical rating label) are not

accessible, readable or recognizable or have been removed from the applicable heating cables or other components, if applicable, or (e) the Owner

fails to return a copy of the completed heating cable tests log with the warranty registration card.

DISCLAIMER: There are no warranties beyond this expressed warranty as stated herein. To the extent permitted by law, all other warranties,

representations or conditions, expressed or implied, are hereby disclaimed and excluded, including but not limited to the implied warranties of

MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE (as limited to such purposes as described in the Written Materials) or arising

from a course of dealing, usage of trade or otherwise by law. ANY IMPLIED WARRANTIES ARISING BY OPERATION OF LAW ARE LIMITED

IN DURATION TO THE TERM OF THIS LIMITED WARRANTY. NO REPRESENTATION, PROMISE, AFFIRMATION OR STATEMENT BY ANY

EMPLOYEE OR AGENT OF SCHLUTER SYSTEMS WILL BE ENFORCEABLE AGAINST SCHLUTER SYSTEMS UNLESS IT IS SPECIFICALLY

INCLUDED IN THIS LIMITED WARRANTY OR AUTHORIZED IN WRITING BY THE SCHLUTER SYSTEMS TECHNICAL SERVICES DIRECTOR. This

Limited Warranty is given in lieu of any other warranty, whether expressed or implied. The remedies contained herein are the only remedies available

for breach of this Limited Warranty. Schluter Systems excludes and in no event shall have any liability for any indirect, special, incidental, punitive,

exemplary, or consequential damages, including lost profits, arising out of or otherwise connected to failure of a DITRA-HEAT System. This Limited

Warranty extends only to the Owner and is not transferable or assignable unless authorized by written agreement and signed by the Schluter Systems

Technical Services Director or otherwise prohibited by specific state or provincial law. This Limited Warranty gives you specific legal rights; some

states and provinces do not allow disclaimers or other restrictions of implied warranties; some of the above disclaimers may not apply to you. No

changes or modifications of any terms or conditions of this Limited Warranty are permitted unless duly authorized in writing by the

Schluter Systems Technical Services Director. This Limited Warranty shall supersede and replace any and all prior oral or written warranties,

agreements, or other representations made by or on behalf of Schluter Systems relative to a DITRA-HEAT System or the application of a DITRA-

HEAT System and shall apply to any installation occurring on or after January 1, 2018. If the Schluter

-DITRA-HEAT or Schluter

-DITRA-HEAT-DUO

uncoupling membrane are used in conjunction with other Schluter products, a different Schluter warranty may apply. For the most current information

and materials regarding Schluter Systems warranties and programs, please visit https://www.schluter.com/DOWNLOADFILES.

MAKING A CLAIM: To make a claim under this Limited Warranty, the Owner must provide Schluter Systems

with written notice within thirty (30)

days of any alleged defect in a DITRA-HEAT System covered by this Limited Warranty, together with date and proof of purchase of such DITRA-

HEAT System and/or all of its components and name and address of all installers and all invoices related to the original installation, failing which this

Limited Warranty shall have no legal effect

. Schluter Systems reserves the right at its election and as a condition of this Limited Warranty to inspect

the alleged failed and/or defective DITRA-HEAT System.

All U.S. Claims shall be sent to: All Canadian Claims shall be sent to:

Schluter Systems L.P. Schluter Systems (Canada), Inc.

Attn: Warranty Claims Dept. Attn: Warranty Claims Dept.

194 Pleasant Ridge Road 21100 chemin Ste-Marie

Plattsburgh, NY 12901 Ste-Anne-de-Bellevue, QC H9X 3Y8

This Limited Warranty is limited to sales of DITRA-HEAT Systems made in and intended for use in the United States and Canada. For the purposes of this Limited Warranty, Schluter Systems

L.P. shall offer warranty coverage to Owners located in the United States, and Schluter Systems (Canada) Inc. shall offer warranty coverage to Owners located in Canada.

In the event that Owner fails to provide such required invoices relating to the original installation, Schluter Systems shall pay Owner an amount equal to the average, reasonable costs of a

comparable installation. If the parties fail to agree on such amount, such dispute shall promptly, and in the first instance, be submitted: (a) if a U.S. claim, to arbitration in Clinton County, New

York, in accordance with the rules of the American Arbitration Association, or (b) if a Canadian claim, in the Province of Quebec, Canada, in accordance with the ADRIC Arbitration Rules.

Any outcome of such arbitration proceeding shall be final and binding upon the parties hereto.

Schluter

-DITRA-HEAT

LIMITED WARRANTY COVERAGE: Subject to the conditions and limitations as stated in this Schluter

-DITRA-HEAT and Schluter-DITRA-

HEAT-DUO Uncoupling Membrane 10-Year Limited Warranty (the “Limited Warranty”), Schluter Systems warrants that its Schluter

DITRA-HEAT and Schluter-DITRA-HEAT-DUO uncoupling membranes (the “Products”) will be free from manufacturing defects and will perform

as described in the Schluter

-DITRA-HEAT Installation Handbook and Schluter

-DITRA-HEAT Technical Data Sheet (collectively, the “Written

Materials”

) for a period of ten (10) years from the date of purchase when installed and used in accordance with the terms and conditions of the

Written Materials and industry standard guidelines that are not in conflict with the Written Materials in effect at the time of installation.

For the purposes of this Limited Warranty, “Owner” is defined as the original end user of the property in which the Products are installed; and “Floor

Covering Assembly” is defined to include the Products, non-reusable flooring surfaces, and applicable setting and grouting materials.

This Limited Warranty is only applicable to installations in the United States of America and Canada. Schluter Systems is not responsible or liable

under any circumstances for determining the suitability of the Products for the Owner’s intended purpose. It is the responsibility of the Owner to

consult with an experienced and professional installer to ensure the suitability of the Products, subfloor/substrate and all building materials in the

installation and that the Written Materials are followed properly.

RESOLUTION: If the Products are installed and used in accordance with the terms and conditions as described hereinabove and such Products

are proven defective within the applicable warranty term, the Owner’s exclusive remedy and the sole obligation of Schluter Systems, at its election,

shall be to (a) reinstall or replace the failed portion of the Floor Covering Assembly or (b) pay an amount not to exceed the original square foot cost

of the installation of the Floor Covering Assembly verified to be defective. Due to conditions beyond the control of Schluter Systems (e.g., color and

shade availability, discontinuation, normal wear and tear), Schluter Systems cannot guarantee or warrant an exact match to the specific tile, stone, or

other flooring materials used in the original installation. In such event, substantially similar materials may be substituted. This Limited Warranty does

not cover the cost of disconnection or installation.

EXCLUSIONS FROM COVERAGE: This Limited Warranty excludes and in no event shall Schluter Systems have any liability for any indirect, special,

incidental, punitive, exemplary, or consequential damages, including lost profits, arising out of or otherwise connected to the failure of the Products,

regardless of any strict liability or active or passive negligence of Schluter Systems, and regardless of legal theory, whether in contract, tort, extra-

contractual or other. This Limited Warranty further excludes any loss or damage arising out of or otherwise connected to: acts of war, terrorism, fire,

explosion, natural disaster, acts of God, any failure to comply with the Written Materials, inadequate subfloor/substrate, improper preparation or other

failure of subfloor/substrate, faulty or negligent penetration of the Products or subfloor/substrate, intentional acts of destruction, structural failure,

misuse of or failure to maintain the Products, normal wear and tear, scratches, dents, corrosion or discoloration (whether caused by excessive heat,

chemical cleaning products, abrasive agents or otherwise), efflorescence and shading which are a natural occurrence with cementitious materials

and are not considered a defective condition for the purposes of this Limited Warranty, variations of texture, color or shade from those on product

samples, packaging materials or other marketing materials, or other causes unrelated to the Products (e.g. excess point loading, overvoltage). This

Limited Warranty excludes exterior applications, unless specifically approved in writing on a case by case basis by the Schluter Systems Technical

Services Director.

This Limited Warranty is conditioned and will be considered null and void and Schluter Systems will have the right to refuse any claims if: (a) the

Products have been improperly stored or installed, or (b) the Products are subject to abusive or abnormal use, lack of maintenance, or used in a

manner other than that for which the Products were designed or in any way contrary to the Written Materials