Casio PX800 User manual

PX800ES1B

ES

USER’S GUIDE

GUÍA DEL USUARIO

Please keep all information for future reference.

Guarde toda información para tener como referencia futura.

Safety Precautions

Before trying to use the piano, be sure to read

the separate “Safety Precautions”.

Precauciones de seguridad

Antes de intentar usar el piano, asegúrese de

leer las “Precauciones de seguridad” separadas.

IMPORTANT SAFETY INSTRUCTIONS

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce

heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the

other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your

safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit

from the apparatus.

11. Only use attachments/accessories specified by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the

apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury

from tip-over.

13. Unplug this apparatus during lightning storms or when unused for long periods of time.

14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as

power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been

exposed to rain or moisture, does not operate normally, or has been dropped.

The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the

apparatus.

The power indicator being unlit does not mean the apparatus is completely disconnected from the MAINS.

When you need to have the apparatus completely disconnected from the MAINS, you must unplug the power cord. For that purpose, locate

the apparatus in a way that secures easy access to the power cord.

Declaration of Conformity

Model Number: PX-800

Trade Name: CASIO COMPUTER CO., LTD.

Responsible party: CASIO, INC.

Address: 570 MT. PLEASANT AVENUE, DOVER, NEW JERSEY 07801

Telephone number: 973-361-5400

This device complies with Part 15 of the FCC Rules, Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that

may cause undesired operation.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert

the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure

that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the

presence of important operating and maintenance (servicing) instructions in the literature

accompanying the product.

CAUTION

RISK OF ELECTRIC SHOCK DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR

BACK). NO USER -SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE

PERSONNEL.

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, REFER SERVICING TO QUALIFIED

SERVICE PERSONNEL.

NOTICE

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or more of the following

measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

• Consult the dealer or an experienced radio/TV technician for help.

FCC WARNING

Changes or modifications not expressly approved by the party responsible for compliance could

void the user’s authority to operate the equipment.

Company and product names used in this manual may be registered trademarks of others.

This mark applies in EU countries only.

CASIO Europe GmbH

Bornbarch 10, 22848 Norderstedt, Germany

This mark applies to the PX-800V only.

Please kee

p

all information for future reference.

E-1

Contents

General Guide ................................... E-2

TEMPO/SETTING Button........................................... E-4

– (T/NO) Button and + (S/YES) Button .................... E-4

Power Supply .................................... E-5

Connections ...................................... E-6

Connecting Headphones ............................................ E-6

Connecting Audio Equipment or an Amplifier............. E-6

Bundled and Optional Accessories............................. E-6

Playing with Different Tones ........... E-7

Selecting and Playing a Tone..................................... E-7

To assign a tone to the VARIOUS/GM TONES

keyboard key .............................................................. E-9

To adjust the brilliance of a tone................................. E-9

Layering Two Tones ................................................. E-10

Splitting the Keyboard between Two Tones ............. E-10

Using Effects............................................................. E-11

Using the Digital Piano’s Pedals............................... E-13

Using the Metronome ............................................... E-13

Playing Back Built-in Songs .......... E-15

Playing Back All of the Built-in Songs....................... E-15

Playing Back a Specific Music Library Song............. E-16

Practicing with a Music Library Song........................ E-16

Recording and Play Back............... E-17

Songs and Tracks..................................................... E-17

To record to a specific track of a specific song......... E-18

To record to one track of a song while listening

to the playback of the other track.............................. E-19

Playing Back from Digital Piano Memory.................. E-19

Deleting Recorded Data ........................................... E-20

Configuring Settings with the

Keyboard ......................................... E-21

Keyboard Keys Used for Configuring Settings ......... E-21

To configure settings with the keyboard ................... E-22

To configure a setting using the

TUNE/OTHERS key ................................................. E-22

To configure a setting using the

MIDI/OTHERS key.................................................... E-22

Keyboard Setting Reference..................................... E-23

Connecting to a Computer............. E-26

Connecting to the MIDI Terminal ..............................E-26

Connecting to the USB Port......................................E-26

USB Mode and MIDI Mode .......................................E-27

Expanding the Selections in the Music Library .........E-28

To install the SMF conversion software

(SMF Converter) ....................................................... E-28

Using an SD Memory Card............. E-29

Inserting and Removing an SD Memory Card ..........E-30

Playing Back a File Stored on an

SD Memory Card ......................................................E-30

Transferring Song Data from an

SD Memory Card to Digital Piano Memory ............... E-31

Saving Song Data Recorded on the

Digital Piano to an SD Memory Card ........................E-32

Formatting an SD Memory Card ...............................E-33

SD Memory Card Errors............................................E-34

Reference......................................... E-41

Troubleshooting ........................................................ E-41

Product Specifications...............................................E-43

Operating Precautions ..............................................E-44

Appendix............................................ A-1

Tone List .....................................................................A-1

Drum Assignment List .................................................A-2

Song List .....................................................................A-3

MIDI Implementation Chart

Assembling the Stand .............................................................................................. E-35

Unpacking................................................................. E-35

Assembling the Stand............................................... E-35

To connect cords.......................................................E-39

To install the music stand..........................................E-40

PX800_e.book 1 ページ２００６年１０月１２日　木曜日　午後１２時５分

E-2

General Guide

8

ck

bm

bo

bq

bs

bl

9

bn

bp

br

bt

cl

bk

cn

cm

1-12 6 753 4

1-2*

Front

Bottom

*The power cord of the PX-800 is hard-wired to the digital piano.

PX800_e.book 2 ページ２００６年１０月１２日　木曜日　午後１２時５分

General Guide

E-3

CAUTION

• Make sure that the cover is fully open whenever you are playing on the keyboard. A partially open cover can suddenly close

unexpectedly and pinch your fingers.

NOTE

• The names shown here are always indicated in bold when they appear within the text of this manual.

1-1 Power supply box

1-2 AC power jack

2Pedal connector

3MIDI OUT/IN terminals

4USB port

5Speaker connector

6LINE OUT R, L/MONO jacks

7PHONES jack

8Display

9TONE lamp

bk SONG lamp

bl – (T

TT

T/NO) button, + (S

SS

S/YES) button

bm TONE/SONG button

bn SONG PLAY/STOP button

bo TEMPO/SETTING button

bp PART/TRACK button

L/1 lamp

R/2 lamp

bq CARD button

br RECORDER button

PLAY lamp, REC lamp

bs GRAND PIANO button

bt METRONOME button

ck Power lamp

cl POWER button

cm VOLUME controller

cn SD CARD SLOT

PX800_e.book 3 ページ２００６年１０月１２日　木曜日　午後１２時５分

E-4

General Guide

The TEMPO/SETTING button is used when

configuring a variety of different digital piano settings.

The following are TEMPO/SETTING button basics.

zThe lamp above the TEMPO/SETTING button

flashes while the button is depressed, and goes out

when the button is released.

zTo change a setting, hold down the TEMPO/

SETTING button as you press the keyboard key that

is assigned the setting you want to select.

Example: “Selecting a Tone Using the Keyboard

Keys” on page E-8.

zSee the “Keyboard Keys Used for Configuring

Settings” on page E-21 for details about the various

settings that can be selected using TEMPO/

SETTING button and keyboard key combinations.

You can change a displayed setting by pressing the

– (T

TT

T/NO) or + (S

SS

S/YES) button as you hold down the

TEMPO/SETTING button.

zHolding down either button changes the value at

high speed.

Example: “Selecting and Playing a Tone” on page

E-7.

NOTE

• Pressing the – (T

TT

T/NO) and + (S

SS

S/YES) buttons at the

same time will return the displayed value to its default

setting.

TEMPO/SETTING Button

Flashing Off

– (T

TT

T/NO) Button and

+ (S

SS

S/YES) Button

PX800_e.book 4 ページ２００６年１０月１２日　木曜日　午後１２時５分

E-5

Power Supply

Your digital piano runs on standard household power.

Be sure to turn off power whenever you are not using

the digital piano.

1.

Make sure that the POWER button is in the

OFF position (raised).

2.

Connect the power cord that comes with the

digital piano to the AC power jack on the

bottom of the digital piano.*

*PX-800V only

3.

Plug the power cord into a household power

outlet.

IMPORTANT!

•Always make sure that the POWER button is the OFF

position before plugging in or unplugging the power cord.

•The shape of the power cord plug and household power

outlet receptacle differ according to country and

geographical area. The illustration shows just one

example of the shapes that are available.

•The power cord of the PX-800 is hard-wired to the digital

piano.

zMake sure the power lamp is completely turned off

before unplugging the power cord from the power

outlet. Be sure to read and observe all of the safety

precautions concerning power supply.

ON

OFF

POWER button

Front

Power lamp

(Power lamp on)

(Power lamp off)

PX800_e.book 5 ページ２００６年１０月１２日　木曜日　午後１２時５分

E-6

Connections

IMPORTANT!

• Whenever connecting something to the digital piano, first

use the VOLUME controller to set the volume to a low

level. After connecting, you can adjust the volume to the

level you want.

Bottom

Connect commercially available headphones to the

PHONES jack. Connecting headphones to the

PHONES jack cuts off output to the speakers, which

means you can practice even late at night without

bothering others. To protect your hearing, make sure

that you do not set the volume level too high when

using headphones.

NOTE

• Be sure to push the headphones plug into the PHONES

jack as far as it will go. If you don’t, you may hear sound

from only one side of the headphones.

You can connect audio equipment or a music amplifier

to the digital piano and then play through external

speakers for more powerful volume and better sound

quality.

IMPORTANT!

• The digital piano automatically adjusts sound output to

optimize for headphone output (when headphones are

connected) or built-in speaker output (when headphones

are not connected). Note that this feature also affects the

sound output from the LINE OUT R and L/MONO jacks.

Connecting Audio Equipment (Figure 1)

R (Right) is the right channel and L/MONO (Left) is the

left channel. Use commercially available connection

cords to connect as shown in Figure 1. Normally, you

should set the input selector of the audio equipment to

the terminal where the digital piano is connected (AUX

IN, etc.) Adjust volume using the digital piano’s

VOLUME controller.

Connecting a Music Amplifier (Figure 2)

R (Right) is the right channel and L/MONO (Left) is the

left channel. Connecting to the L/MONO jack only

outputs a mixture of both channels. Use a

commercially available connection cord to connect as

shown in Figure 2. Adjust volume using the digital

piano’s VOLUME controller.

Use only accessories that are specified for use with this

digital piano.

Use of unauthorized accessories creates the risk of fire,

electric shock, and personal injury.

Connecting Headphones

Connecting Audio Equipment

or an Amplifier

Commercially available

headphones

Stereo standard plug

PHONES jack

Bundled and Optional

Accessories

INPUT 1

INPUT 2

Audio amplifier AUX IN jack, etc.

Guitar amplifier

Keyboard amplifier, etc.

Pin plug

LEFT

(White)

Standard jack

Standard plug

RIGHT

(Red)

PX800_02_e.fm 6 ページ２００６年１０月１２日　木曜日　午後４時１３分

E-7

Playing with Different Tones

Your digital piano has the following types of tones

built in.

*You can select these tones using keyboard keys. The

name of the tones assigned to each keyboard key is

marked above the keys. For details about selecting

these tones, see “Selecting a Tone Using the

Keyboard Keys” on page E-8.

1.

Press the POWER button to turn on the

digital piano.

IMPORTANT!

•When you turn on the digital piano, it performs a power

up operation in order to prepare its system. The power up

operation takes about 10 seconds, and is indicated by

the following messages appearing on the display.

2.

Select the tone you want.

zTo select the GRAND PIANO tone, simply press the

GRAND PIANO button.

• To select another tone, find its tone name in the

“Tone List” on page A-1 and note its tone number.

Example: To select Tone Number 07, Harpsichord

•Use the + and – buttons to change the displayed

tone number until it matches the one you want (07

in this example).

NOTE

• There are two sets of tone numbers, one set from 01 to 12

and another set from 001 to 150. Pressing the + button

while 12 is displayed will change the tone number to 001.

Similarly, pressing the – button while 001 is displayed

will change the tone number to 12.

• Holding down either button changes the displayed value

at high speed.

3.

Use the VOLUME controller to adjust the

volume level.

4.

Try playing something on the digital piano.

POWER

VOLUME

GRAND PIANO

METRONOME

TEMPO/SETTING

TONE

/

Selecting and Playing a Tone

Tone Numbers Tone Type Number of

Tones

01 to 12 Keyboard*12

001 to 020 Various 20

021 to 148 GM (General MIDI) 128

149, 150 Drum Sets 2 sets

(Please wait!)

(Preparing system)

(Complete!)

PX800_e.book 7 ページ２００６年１０月１２日　木曜日　午後１２時５分

E-8

Playing with Different Tones

NOTE

•The DSP* effect will be applied if you select a tone with DSP.

• Note that the digital piano’s DSP resources are limited. Because of this, selecting a tone with DSP can cause notes that are

currently being played to cut off (if they are being played using a tone with DSP), or it can remove the DSP effect from an

operation (layer, split, demo tune) that was previously assigned a tone with DSP.

(* See page E-12)

Selecting a Tone Using the Keyboard Keys

1.

While holding down the TEMPO/SETTING button, press the keyboard key that corresponds to the

tone you want to select.

• This will cause the lamp above the button to flash and the tone number of the selected tone to appear on the display.

*A note does not sound when you press the keyboard key to select a tone.

A0B0C1D1E1F1G1A1B1C2D2E2F2

Tone Setting Keys

A0: 01 Grand Piano

B0: 02 Grand Piano 2

C1: 03 Grand Piano 3

D1:04 Electric Piano 1

E1:05 Electric Piano 2

F1:06 Electric Piano 3

G1:07 Harpsichord

A1: 08 Vibraphone

B1: 09 Pipe Organ

C2: 10 Percussive Organ

D2: 11 Strings

E2: 12 Acoustic Bass

F2: 001 to 150 Various/GM Tones

PX800_e.book 8 ページ２００６年１０月１２日　木曜日　午後１２時５分

Playing with Different Tones

E-9

1.

While holding down the TEMPO/SETTING

button, press the VARIOUS/GM TONES

keyboard key. Keep the TEMPO/SETTING

button depressed until you finish step 2 of this

procedure.

• This will cause the TEMPO/SETTING button to flash

and the tone number of the Various, GM, or Drum

Sets Tone currently assigned to the keyboard key to

appear on the display.

2.

Use the + and – buttons to display the tone

number of the Various, GM, or Drum Sets

Tone you want to assign to the VARIOUS/GM

TONES key.

Example: 019 FANTASY

NOTE

• If a drum set is assigned to the VARIOUS/GM TONES

key, keyboard keys sound drum sounds. See page A-2

for information about the drum sounds that are assigned

to each of the keyboard keys.

1.

While holding down the TEMPO/SETTING

button, press the BRILLIANCE keyboard key.

Keep the TEMPO/SETTING button

depressed until you finish step 2 of this

procedure.

• This will cause the lamp above the TEMPO/

SETTING button to flash and the currently selected

brilliance value to appear on the display.

2.

Use the + and – buttons to change the

displayed value.

NOTE

• Pressing the + and – buttons at the same time while

holding down the TEMPO/SETTING button (step 2)

will return the brilliance setting to its default value.

To assign a tone to the

VARIOUS/GM TONES

keyboard key

To adjust the brilliance of a

tone

For this type of sound: Select a value in this

range:

Soft and smooth –3 to –1

Bright and sharp 1 to 3

PX800_e.book 9 ページ２００６年１０月１２日　木曜日　午後１２時５分

E-10

Playing with Different Tones

Use the following procedure to layer two tones, so they

sound at the same time.

1.

Hold down the TEMPO/SETTING button until

you finish step 2 of this procedure.

2.

While holding down the keyboard key that

corresponds to the main tone, press any

nearby keyboard key that corresponds to

another tone.

• The second key you press is the layered tone. We will

be changing it in step 3, below.

Example: While holding down the GRAND PIANO 2

key, press the GRAND PIANO 3 key.

• The tone numbers of the layered tone will appear on

the display.

3.

Use the + and – buttons to change the

displayed tone number to the one you want to

select.

Example: 11 STRINGS

4.

Try playing something on the keyboard.

5.

To unlayer the keyboard, select another tone

by pressing the GRAND PIANO button or by

using the procedure under “Selecting a Tone

Using the Keyboard Keys” (page E-8).

NOTE

• You can adjust the balance between the main tone and

layered tone. See “Configuring Settings with the

Keyboard” on page E-21 for more information.

You can assign different tones to keys on the left side

and the right side of the keyboard.

1.

Use the procedure under “Selecting and

Playing a Tone” on page E-7 to select the

high range tone.

Example: GRAND PIANO 2

2.

While holding down the TEMPO/SETTING

button, press the SPLIT ON/OFF keyboard

key. Keep the TEMPO/SETTING button

depressed until you finish step 3 of this

procedure.

Layering Two Tones

GRAND PIANO 2

GRAND PIANO 3

Splitting the Keyboard

between Two Tones

Split Point

Low Range High Range

STRINGS GRAND PIANO 2

PX800_e.book 10 ページ２００６年１０月１２日　木曜日　午後１２時５分

Playing with Different Tones

E-11

3.

Use the + and – buttons to turn keyboard split

on or off.

• Releasing the TEMPO/SETTING button will cause

the display to change to the number of the currently

selected low-range tone.

4.

Use the procedure under “Selecting and

Playing a Tone” on page E-7 to select the low

range tone.

Example: 11 STRINGS

NOTE

• You can also specify the location of the keyboard split

point. See “Configuring Settings with the Keyboard” on

page E-21 for more information.

• You can configure the keyboard so it is layered with two

tones in the high range. To do this, first perform the layer

operation (page E-10). After that, split the keyboard as

described above.

Reverb. . . .Makes your notes resonate.

Chorus . . .Adds more breadth to your notes.

Acoustic Resonance . . .

When the damper pedal is pressed,

reproduces the harmonic resonance within

a grand piano.

DSP . . . . . .Digitally processes tones to for more

sophisticated effects. Each tone is preset

with a default DSP effect (drawbar organ

tone + rotary speaker, for example).

To configure reverb and chorus effect

settings

1.

While holding down the TEMPO/SETTING

button, press the REVERB or CHORUS

keyboard key. Keep the TEMPO/SETTING

button depressed until you finish step 2 of this

procedure.

• This will cause the lamp above the TEMPO/

SETTING button to flash and the currently selected

reverb or chorus value to appear on the display.

Reverb

Chorus

When the display

shows this: It means this:

oFF Keyboard split off

on Keyboard split on

Using Effects

PX800_e.book 11 ページ２００６年１０月１２日　木曜日　午後１２時５分

E-12

Playing with Different Tones

2.

Use the + and – buttons to change the

displayed value.

• Reverb Value

•Chorus Value

To turn acoustic resonance and DSP on

or off

1.

While holding down the TEMPO/SETTING

button, press the ACOUSTIC RESONANCE

or DSP keyboard key. Keep the TEMPO/

SETTING button depressed until you finish

step 2 of this procedure.

• This will cause the lamp above the TEMPO/

SETTING button to flash and the currently selected

acoustic resonance or DSP setting to appear on the

display.

Acoustic Resonance

DSP

To do this: Select this setting:

Turn off reverb oFF

Turn on reverb

1: Room

2: Small Hall

3: Large Hall

4: Stadium

To do this: Select this setting:

Turn off chorus oFF

Turn on chorus

1: Light Chorus

2: Medium Chorus

3: Deep Chorus

4: Flanger (Whooshing effect)

PX800_e.book 12 ページ２００６年１０月１２日　木曜日　午後１２時５分

Playing with Different Tones

E-13

2.

Use the + and – buttons to change the

displayed setting.

NOTE

• While the keyboard is layered, the DSP on/off setting

affects the layered tone only. While the keyboard is split,

the DSP on/off setting affects the low range tone only.

• Turning on DSP will apply the DSP effect to tones with

DSP only. It will not be applied to any other type of tone.

Your digital piano comes equipped with three pedals:

damper, soft, and sostenuto

Pedal Functions

z

zz

zDamper Pedal

Pressing the damper pedal while playing will cause

the notes you play to reverberate for a very long

time.

• When GRAND PIANO, GRAND PIANO 2, or

GRAND PIANO 3 is selected as the tone, pressing

this pedal will cause notes to reverberate just like

the damper pedal on an acoustic grand piano.

Half-pedal operation (pressing the pedal part way)

is also supported.

z

zz

zSoft Pedal

Pressing this pedal while playing suppresses notes

played on the keyboard after the pedal was pressed,

and makes them sound softer.

z

zz

zSostenuto Pedal

Only the notes of the keys that are depressed when

this pedal is pressed are sustained until the pedal is

released.

1.

Press the METRONOME button.

• This starts the metronome.

• The two lamps above the SONG PLAY/STOP button

flash in time with the metronome beat.

2.

To change the beat, hold down the

METRONOME button as you use the + and –

buttons to make adjustments.

• You can select a beat value in the range of 2 through

6. Specifying 0 as the setting plays a straight click,

without any chime. This setting lets you practice with

a steady beat.

3.

While holding down the TEMPO/SETTING

button, use the + and – buttons to adjust the

tempo in a range of 20 to 255 beats per

minute.

4.

Press the METRONOME button again to stop

the metronome.

NOTE

• You can also set the beat setting (step 2) using the

procedure described under “Configuring Settings with

the Keyboard” on page E-21.

When the display

shows this: It means this:

oFF Effect off

on Effect on

Using the Digital Piano’s

Pedals

Soft pedal Damper pedal

Sostenuto pedal

Using the Metronome

PX800_02_e.fm 13 ページ２００６年１０月１２日　木曜日　午後６時５３分

E-14

Playing with Different Tones

To adjust the metronome volume

NOTE

• You can perform the following procedure at any time,

regardless of whether or not the metronome is sounding.

1.

While holding down the TEMPO/SETTING

button, press the METRONOME VOLUME

keyboard key. Keep the TEMPO/SETTING

button depressed until you finish step 2 of this

procedure.

• This will cause the lamp above the TEMPO/

SETTING button to flash and the current metronome

volume setting to appear on the display.

2.

Use the + and – buttons to change the

metronome volume setting in the range of 0

to 42.

PX800_e.book 14 ページ２００６年１０月１２日　木曜日　午後１２時５分

E-15

Playing Back Built-in Songs

IMPORTANT!

•After you select a built-in song, it can take a number of

seconds for the song data to be loaded. While the data is

being loaded, the song number will flash on the display,

and the keyboard keys and button operations will be

disabled. If you are playing something on the keyboard,

the following operation will cause output to stop.

Your digital piano has a total of 72 built-in songs. You

can use the procedure to play back all of the songs, one

after the other.

*A “keyboard tone demo tune” is a demo tune that

use the tone that is currently assigned to the

keyboard for its melody.

1.

While holding down the TONE/SONG button,

press the SONG PLAY/STOP button.

• This will start sequential playback from keyboard

tone demo tune t.01, up to the last Music Library song

L.60.

• You can play along with a song on the keyboard as it

is playing. The tone assigned to the keyboard is the

one that is preset for the song that is playing.

• You can use the + and – buttons to skip sequentially

between songs during playback.

• Pressing the + and – buttons at the same time will

return to keyboard tone demo tune t.01.

2.

Press the SONG PLAY/STOP button again to

stop built-in song play.

SONG PLAY/STOP

PART/TRACK

TONE/SONG

TONE

/

SONG

Playing Back All of the Built-in

Songs

Type Number of

Songs Display Indicator

Keyboard tone

demo tune*12

TONE lamp flashes,

song number displayed

Music Library 60

SONG lamp flashes,

song number displayed

PX800_e.book 15 ページ２００６年１０月１２日　木曜日　午後１２時５分

E-16

Playing Back Built-in Songs

The Music Library includes both preset songs (01 to

60), plus up to 10 songs (61 to 70) that have been saved

to digital piano memory from a computer* or loaded

SD memory card (page E-29). You can use the

procedure below to select one of these songs and play it

back.

*You can download music data from the Internet and

then transfer it from your computer to digital piano

memory. See “Expanding the Selections in the Music

Library” on page E-28 for more information.

1.

Press the TONE/SONG button so the SONG

lamp is lit.

• Each press of the TONE/SONG button toggles

between the TONE and SONG indicator lamps.

• This will cause the currently selected song number to

appear on the display.

2.

Find the song number of the song you want to

play in the song list on page A-3.

3.

Use the + and – buttons to display the song

number of the song you want to play.

4.

Press the SONG PLAY/STOP button.

• This starts the playback of the song.

5.

To stop playback, press the SONG PLAY/

STOP button again.

• Playback will stop automatically when the end of the

song is reached.

NOTE

•Pressing the + and – buttons at the same time will select

song number 01.

• You can change tempo, volume, and pre-count settings

for playback. See “Configuring Settings with the

Keyboard” on page E-21 for more information.

You can turn off the left hand part or right hand part of

a Music Library song and play along on the piano.

NOTE

• The Music Library includes a number of duets. While a

duet is selected, you can turn off the first piano <Primo>

or second piano <Secondo> tone and play along with the

song.

PREPARATION

• Select the song you want to practice and adjust the

tempo. See “Configuring Settings with the Keyboard” on

page E-21.

• A number of tunes have tempo changes part way

through in order to produce specific musical effects.

1.

Use the PART/TRACK button to turn off a

part.

•Each press of the PART/TRACK button cycles

through the part settings as shown below. The

indicator lamps above the button show which part is

turned off.

2.

Press the SONG PLAY/STOP button.

• This starts playback, without the part you turned off

in step 1.

3.

Play the missing part on the keyboard.

4.

To stop playback, press the SONG PLAY/

STOP button again.

Playing Back a Specific Music

Library Song Practicing with a Music

Library Song

Left hand Right hand

Both parts

on

Right hand

part off

Left hand

part off

PX800_e.book 16 ページ２００６年１０月１２日　木曜日　午後１２時５分

Page is loading ...

Casio PX800 User manual

This manual is also suitable for

Casio PX800 User manual

Related papers

Other documents