Orion RNK55NHF Installation and User Manual

Brand: Orion

Model: RNK55NHF

Category: LED displays

Type: Installation and User Manual

VIDEO WALL SOLUTION

(22~82 inches)

Installation and User's Guide

All contents of this document may change without prior notice, and actual product appearance may differ from that depicted herein

1. SAFETY INSTRUCTION

Follow this safety instruction to use the monitor properly and prevent the damages.

Keep this user’s guide book for later use.

This safety instruction has “Warning” & “Caution” as below

Warning - If the user does not follow this instruction,

it may cause the serious damage to the user.

Caution - If the user does not follow this instruction, it may cause the slight

damage to the user or cause some damages to the monitor.

Warning

Keep away the monitor from the

direct sunlight and a heating appliance.

Never push objects of any kind into

this product as they may result in

a risk of fire or electric shock.

Connect the power code to the wall

outlet tightly. If the power code or plug

are defective and the wall outlet is not

tight, please do not use them.

Never remove the back over and

touch the inside of the monitor.

If you need a service, please

contact the service center.

Installation and User's Guide

Warning

Do not install this monitor on the outside

and near water. If may cause damage to

the product, electric shock and fire.

For cleaning do not use liquid cleaners.

Never touch the power plug with wet-hands.

When lightning and thundering, unplug the

monitor from the wall outlet and never touch

it.

When smoking and noising from the monitor,

unplug the product from the wall outlet and

contact a service center.

Unplug this product from the wall outlet, when

It does not operate for a long time.

How to fix

Do not open this product as it contains high voltage inside.

It may create an electric shock.

It the user disassembles and remove the back cover, it does not make sure

to make up for the damages and do a service and exchange the monitor.

Installation and User's Guide

Cautions

Install this monitor some distance

From the wall and do not install unless

Proper ventilation is provided.

Place this product on a stable place.

If not, it may fall, causing serious

Damages to the monitor and people.

The openings must not be blocked by

curtain, rug or other similar surface.

Before carrying the monitor, tum it off and

Unplug the signal cables and the power code

From the wall outlet.

When carrying this monitor, be careful

not to damage the panel and drop it

It may cause some trouble.

Take the power plug out from the wall

outlet.

Do not pull the cable. It may snap the inner-

wires and cause overheating and fire.

Installation and User's Guide

Cautions

Install this monitor about 50cm far from

the eyes and an angle of 0~15 degrees

below eyes. Too close installation may

cause having weak sight.

Do not press the LCD panel with hands or

the sharpened material hardly.

Do not use the chemical liquid for cleaning.

It may cause fading and breakage.

For cleaning, unplug the monitor from the

Wall outlet. Do net use the liquid cloth.

Use the soft cloth.

WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT EXPOSE

THIS EQUIPMENT TO RAIN OR WATER.

Instructions for Disposal of Electrical and Electronic Equipment in Private

Households

Disposal of used Electrical and Electronic Equipment

(Applicable in the European Union and other European countries with garbage separate

disposal and collection methods)

This symbol on the product, or in the related documents in the package, indicates that this

product shall not be treated as normal household waste. Instead, it should be taken to a proper

applicable collection point or depot for the recycling of electrical and electronic equipment.

By ensuring this product is disposed of correctly, you will help prevent possible negative consequences for

the environment and human health, which could otherwise be caused by inappropriate waste handling of

this product. The recycling of materials will help to conserve natural resources.

For more detailed information about recycling of this product, please contact your local city authority, your

household waste disposal service or the place where you purchased the product.

2. FCC RF INTERFERENCE STATEMENT

NOTE

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment

generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or more of the following measures.

● Reorient or relocate the receiving antenna.

● Increase the separation between the equipment and receiver.

● Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

● Consult the dealer or an experienced radio, TV technician for help.

● Only shielded interface cable should be used.

Finally, any changes or modifications to the equipment by the user not expressly approved by the grantee or manufacturer could void

the users authority to operate such equipment.

DOC COMPLIANCE NOTICE

This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus set out in the radio

interference regulation of Canadian Department of communications.

Installation and User's Guide

1. SAFETY INSTRUCTION

1-1 Warning

1-2 Caution

2. FCC STATEMENT

3-1 Parts

3-2 How to Install

7. TROUBLESHOOTING

3. INSTALLATION

4-1 Mode Setting

4-2 Menu Setting

4. OSD MENU SETTING

5. FEATURES

6. MECHANICAL DRAWING

TABLE OF CONTENTS

Installation and User's Guide

3. INSTALLATION

3-1 Parts

LCD Monitor & Keypad

UTP Cable VGA Cable Serial Cable

Joint Bracket

Trigger Cable Power Cable Remote Controller

Battery Install CD User Manual

(Only 40 inches or more)

Installation and User's Guide

3-2 How to Install

UTP Cable (1.5m)

If you want to replace with a longer cable Please purchase separately

This KEYPAD is attached to a magnet, so you can freely paste

SHORT KEY FUNCTION

KEYPAD CONTROLLER

OSD KEY FUNCTION

On/off the OSD menu or exit the source selection menu

Move the cursor to choose on the OSD menu

Select the source on the INPUT menu

Move up the cursor to choose on the OSD menu

Activate the auto adjustment of RGB source

Control down on the OSD menu or move to the previous menu

Volume down

Select the OSD menu

Control up on the OSD menu

Volume up

Turn the power ON or OFF. There will be a few seconds delay before the

display appears. The power LED (next to the power switch) lights with green

when the power is turned ON. The power is turned off by pressing the power

switch again and the power LED goes red.

Installation and User's Guide

CONNECTION

1 2 3 4 5 6

1 2 3 4 5 6 14

7 8 9 10 11 12 13

HDMI

22 inches

40~82 inches

1VIDEO-2 IN / OUT

HDMI Signal input / loop output VIDEO-2 Signal input / loop output

DVI

2AUDIO (VIDEO-1)

DVI Signal input / loop output Stereo audio input for VIDEO-1

VGA

3AUDIO (VIDEO-2)

VGA (PC RGB) Signal input / loop output Stereo audio input for VIDEO-2

RS-232 IN / OUT

4TRIGGER

SERIAL Cable input / output for RS-232 TRIGGER Signal input

KEYPAD

5SPEAKER OUT

UTP Cable input for KEYPAD Stereo speaker output

AUDIO (PC)

6AC POWER

Stereo audio input for VGA AC 100-240V input

VIDEO-1 IN / OUT

7DC24V

VIDEO-1 Signal input / loop output DC 24V (Adapter) input

Installation and User's Guide

CONFIGURE THE VIDEO WALL

CENTER

Assemble the JOINT BRACKET

using four M4 screws.

SIDE

Assemble the JOINT BRACKET

using two M4 screws.

1. You can combine two or more monitors, and configure the VIDEO WALL.

2. If you want to configure VIDEO WALL, please contact your dealer or

a professional installer.

3. JOINT BRACKET helps to easily adjust the VIDEO WALL. (Supplied with monitor)

HDMI OUT

HDMI IN

DVI OUT

DVI IN

VGA OUT

VGA IN

RS-232 OUT

RS-232 IN

VIDEO1 OUT

VIDEO1 IN

VIDEO2 OUT

VIDEO2 IN

CABLES CONNECTION

* Cable connection order, it may be different

from the order of the 'SET ID' or 'SEQUENCE'

(Refer to page 15~17)

1st MONITOR

2nd MONITOR

3rd MONITOR

4th MONITOR

* Please install the VWCP (Video Wall Control Program) for remote control of the monitors through the computer.

For information about installing and using VWCP, please refer to the installation disk that came with the monitor.

Installation and User's Guide

REMOTE CONTROLLER

MODE SELECT MENU

VIDEO 1 (Only 40 inches or more)

Select VIDEO 1 mode

VIDEO 2 (Only 40 inches or more)

Select VIDEO 2 mode

VGA (RGB)

Select VGA mode

DVI

Select DVI mode

HDMI

Select HDMI mode

POWER

Turn ON / OFF the monitor

MUTE

Turn ON / OFF the sound

AUTO

Auto adjust position of the screen (in VGA mode)

COLOR TEMPERATURE

Select color temperature of the screen

SCAN MODE

Select the scan mode of the screen

VOL- / VOL+

Increase / Decrease the volume level

MENU / EXIT

Activate and exit the OSD menu

STILL

Freeze the current image

KEY LOCK

Locking the button (Prevent operation)

S. SET

Select between main and PIP audio input

PIP

Activates PIP/PBP mode

P. INPUT

Select an input source for PIP mode

P. LOCATION

Select a location for PIP mode

P. SIZE

Select a size for PIP mode

P. SWAP

Swap between main and PIP input

OSD CONTROL MENU

PIP CONTROL MENU

POWER MUTE

VIDEO1 VIDEO2

VGA AUTO COLOR TEMP

DVI HDMI

S.SET

SCAN MODE PIP

MENU/EXIT

P.INPUT P.LOCATION

P.SWAP STILL

P.SIZE

KEY LOCK

VOL- VOL+

Installation and User's Guide

4. OSD MENU SETTING

4-1 Mode Setting

VIDEO1 Select VIDEO1 Mode (Only 40 inches or more)

VIDEO2 Select VIDEO2 Mode (Only 40 inches or more)

RGB PC Select VGA Mode

DVI Select DVI Mode

HDMI Select HDMI mode

VIDEO1

VIDEO2

√RGB PC

DVI

HDMI

▼/▲:MOVE ▶:ENTER

INPUT

1. Use Source button and then ▲ or ▼ button to move the source.

2. Press the ► button to select the source.

3. Press the MENU/EXIT button to exit the INPUT menu.

Installation and User's Guide

4-2 Menu Setting

PICTURE

ITEM FUNCTION DEFAULT VALUE AVAILABLE MODE

CONTRAST Adjust the contrast level of color All modes

BRIGHTNESS Adjust the brightness level of color All modes

COLOR Adjust the depth of color VIDEO, HDMI

TINT Adjust the tint of color (only NTSC signal) VIDEO, HDMI

SHARPNESS Adjust the sharpness of picture VIDEO, HDMI

PEAKING CONTROL Adjust the sharpness of outline HDMI

COLOR TEMP Set the color temperature of screen

(MEDIUM, WARM, USER, COOL) All modes

60%

50%

MEDIUM

PICTURE

CONTRAST

60%

BRIGHTNESS

50%

COLOR

50%

TINT

50%

SHARPNESS

50%

PEAKING CONTROL 50%

COLOR TEMP ◀ MEDIUM

RED

128

GREEN

128

BLUE

▼/▲ : MOVE ◀/▶ : ADJUST ▶ : ENTER MENU : EXIT VER : *.*

128

PICTURE

SCREEN

SETUP

RGB

SETUP

CYCLE

TRIGGER

▶

1. Press the MENU key to access menu.

2. Use the ▲ or ▼ key to choose PICTURE.

3. Press the ► key to enter the PICTURE menu.

4. Use the ▲ or ▼ key to choose an item of PICTURE.

5. Use the ◄ or ► key to adjust the setting on a selected item.

Installation and User's Guide

SCREEN

ITEM FUNCTION DEFAULT VALUE AVAILABLE MODE

H MONITORS

Set the total number of horizontally installed monitors

on the video wall situation

(01 ~ 99) All modes

V MONITORS Set the total number of vertically installed monitors

on the video wall situation

(01 ~ 99) All modes

SEQUENCE Set the sequence of installed monitors on the video

wall situation

(01 ~ 99) All modes

H GAP Set the horizontal gap between adjacent panels

caused by bezel width

(00 ~ 99) All modes

V GAP Set the vertical gap between adjacent panels

caused by bezel width

(00 ~ 99) All modes

SCAN MODE Select the scan mode of the screen

(FULL, REAL,*UNDER, OVER, 4:3)

*UNDER : It does not appear in HDMI mode

All modes

FULL

PIP Activate PIP/PBP mode (OFF, ON, DW1, DW2)

(Only 40 inches or more) HDMIOFF

SCREEN

SCAN MODE

PIP

PIP INPUT

PIP SWAP

PIP SIZE

PIP LOCATION

PICTURE

SCREEN

SETUP

RGB

SETUP

CYCLE

TRIGGER

◀ R/B ▶

◀ SMALL ▶

▶

◀ VIDEO2 ▶

◀ OFF ▶

◀ FULL ▶

SEQUENCE

H GAP

V GAP ◀ 00 ▶

◀ 00 ▶

◀ 01 ▶

H MONITORS

V MONITORS ◀ 01 ▶

◀ 01 ▶

▼/▲ : MOVE ◀/▶ : ADJUST ▶ : ENTER MENU : EXIT VER : *.*

1. Press the MENU key to access menu.

2. Use the ▲ or ▼ key to choose SCREEN.

3. Press the ► key to enter the SCREEN menu.

4. Use the ▲ or ▼ key to choose an item of SCREEN.

5. Use the ◄ or ► key to adjust the setting on a selected item.

Installation and User's Guide

SCAN MODE

ex) In case of 3X2 Video Wall Setting

REAL : Display original images entered from the source intactly

UNDER : Display the image on the smaller area than the screen

Original image is fully displayed.

OVER : Display the image on the broader area than the screen

Original Image is cut off on the edge.

4:3 : Display the image to 4:3 aspect ratio

PIP

Default Setting is OFF and changeable to ON, DW1 and DW2 PIP/PBP modes.

OFF : PIP/PBP modes are not activated.

ON : Switch on PIP/PBP mode

DW1 : change to Double Window mode 1

DW2 : change to Double Window mode 2

After selecting PIP/PBP modes, following items are activated.

PIP INPUT : Select an input source for PIP image (VIDEO 1, VIDEO 2)

PIP SWAP : Swap main picture and sub picture

PIP SIZE : Select the size of PIP image (SMALL, NORMAL, LARGE)

PIP LOCATION : Select the position of PIP image (R/B, L/B)

SEQUENCE numerical order

1 2 3 4

5 6 7 8

9 10 11 12

13 14 15 16

H MONITORS : 03

V MONITORS : 02

SEQUENCE : 01

H MONITORS : 03

V MONITORS : 02

SEQUENCE : 02

H MONITORS : 03

V MONITORS : 02

SEQUENCE : 03

H MONITORS : 03

V MONITORS : 02

SEQUENCE : 05

H MONITORS : 03

V MONITORS : 02

SEQUENCE : 06

H MONITORS : 03

V MONITORS : 02

SEQUENCE : 04

H GAP : 01

V GAP : 01

Installation and User's Guide

SETUP

INPUT

LANGUAGE

AUDIO MUTE

AUDIO OUT

NOISE REDUCTION

OSD TIME

PICTURE

SCREEN

SETUP

RGB

SETUP

CYCLE

TRIGGER

DEFAULT ▶

SET ID ◀ 01 ▶

KEY LOCK ◀ OFF ▶

LINE SHIFT ◀ OFF ▶

◀ ON ▶

◀ OFF ▶

◀ INTERNAL ▶

◀ ENGLISH ▶

◀ VIDEO1 ▶

▼/▲ : MOVE ◀/▶ : ADJUST ▶ : ENTER MENU : EXIT VER : *.*

15s

FAN CONTROL

FAN AUTO REF

◀ AUTO ▶

42c

FAN SPEED

CURRENT TEMP

◀ NORMAL ▶

42c

ITEM FUNCTION DEFAULT VALUE AVAILABLE MODE

INPUT Select the input source for main picture All modes

LANGUAGE Set the language of OSD

(ENGLISH, ITALIAN, FRENCH, SPANISH, GERMAN)

All modes

AUDIO MUTE Turn on/off the audio output All modes

AUDIO OUT Select the speaker for audio output

(INTERNAL, EXTERNAL) All modes

NOISE REDUCTION Set the noise reduction mode All modes

OSD TIME Set the time duration of OSD menu (5~30s) All modes

CURRENT TEMP Display the current temperature All modes

ENGLISH

OFF

INTERNAL

15s (seconds)

DEFAULT Factory default setting All modes

SET ID Allocate an ID of the set for RS-232 control All modes01

KEY LOCK Lock the key action (Prevent operation) All modesOFF

LINE SHIFT Move the image a little instantaneously to protect

the screen All modesOFF

FAN CONTROL Select the control method of FAN (AUTO, ON, OFF) All modesAUTO

FAN AUTO REF Set the reference temperature for automatic FAN

control (20~60c) All modes42c (celsius)

FAN SPEED Select the speed of FAN (NORMAL, FAST, SLOW) All modesNORMAL

1. Press the MENU key to access menu.

2. Use the ▲ or ▼ key to choose SETUP.

3. Press the ► key to enter the SETUP menu.

4. Use the ▲ or ▼ key to choose an item of SETUP.

5. Use the ◄ or ► key to adjust the setting on a selected item.

Installation and User's Guide

RGB SETUP (ONLY RGB PC MODE)

RGB SETUP

H-POSITION

V-POSITION

CLOCK

PHASE

AUTO ADJUST

POWER SAVING

PICTURE

SCREEN

SETUP

RGB

SETUP

CYCLE

TRIGGER

AUTO REPEAT ◀ OFF ▶

▶

◀ OFF ▶

▼/▲ : MOVE ◀/▶ : ADJUST ▶ : ENTER MENU : EXIT VER : *.*

100%

ITEM FUNCTION DEFAULT VALUE AVAILABLE MODE

H-POSITION Adjust the horizontal position of the screen RGB PC

V-POSITION Adjust the vertical position of the screen RGB PC

CLOCK Adjust the clock of the screen RGB PC

PHASE Adjust the phase of the screen RGB PC

AUTO ADJUST Adjust all of above items for suitable screen RGB PC

POWER SAVING Adjust the power saving mode RGB PCOFF

AUTO REPEAT Repeat AUTO ADJUST action automatically RGB PCOFF

To cancel KEY LOCK mode

Remote Controller : Press KEY LOCK button

Keypad : Press ▲ & ◄ buttons simultaneously

1. Press the MENU key to access menu.

2. Use the ▲ or ▼ key to choose RGB SETUP.

3. Press the ► key to enter the RGB SETUP menu.

4. Use the ▲ or ▼ key to choose an item of RGB SETUP.

5. Use the ◄ or ► key to adjust the setting on a selected item.

Installation and User's Guide

CYCLE SETUP (ONLY 40 INCHES OR MORE)

ITEM FUNCTION DEFAULT VALUE AVAILABLE MODE

CYCLE TIME Adjust the time interval to display selected mode All modes

CYCLE

Display selected modes sequentially in set cycle time

All modes

VIDEO1 Choice as to whether to cycle of VIDEO1 mode All modes

VIDEO1 Choice as to whether to cycle of VIDEO2 mode All modes

RGB PC Choice as to whether to cycle of RGB PC mode All modes

DVI Choice as to whether to cycle of DVI mode All modesOFF

OFF

10s (seconds)

HDMI Choice as to whether to cycle of HDMI mode All modesOFF

1. Press the MENU key to access menu.

2. Use the ▲ or ▼ key to choose CYCLE SETUP.

3. Press the ► key to enter the CYCLE SETUP menu.

4. Use the ▲ or ▼ key to choose an item of CYCLE SETUP.

5. Use the ◄ or ► key to adjust the setting on a selected item.

CYCLE SETUP

CYCLE TIME

CYCLE

VIDEO1

VIDEO2

RGB PC

DVI

PICTURE

SCREEN

SETUP

RGB

SETUP

CYCLE

TRIGGER

HDMI

◀ OFF ▶

▼/▲ : MOVE ◀/▶ : ADJUST ▶ : ENTER MENU : EXIT VER : *.*

10s

Installation and User's Guide

TRIGGER (ONLY 40 INCHES OR MORE)

TRIGGER

TRIGGER MODE

TRIGGER INPUT

TRIGGER DWELL

PICTURE

SCREEN

SETUP

RGB

SETUP

CYCLE

TRIGGER

◀ OFF ▶

◀ VIDEO1 ▶

▼/▲ : MOVE ◀/▶ : ADJUST ▶ : ENTER MENU : EXIT VER : *.*

10s

ITEM FUNCTION DEFAULT VALUE AVAILABLE MODE

TRIGGER MODE Set the trigger mode All modes

TRIGGER INPUT Select the input source of trigger mode

(VIDEO1, VIDEO2) All modes

TRIGGER DWELL Set the display time of trigger mode (10~60s) All modes

OFF

VIDEO1

10s (seconds)

1. Press the MENU key to access menu.

2. Use the ▲ or ▼ key to choose TRIGGER.

3. Press the ► key to enter the TRIGGER menu.

4. Use the ▲ or ▼ key to choose an item of TRIGGER.

5. Use the ◄ or ► key to adjust the setting on a selected item.

INPUT SIGNAL MODE RESOLUTION VERTICAL FREQUENCY (Hz)

VGA / DVI

VGA 640X480 60 / 72 / 75

VGA 720X400 70

SVGA 800X600 56 / 60 / 75

XGA 1024X768 60 / 75

SXGA- 1280X960 60

SXGA 1280X1024 60 / 75

WXGA 1366X768 60

WXGA+ 1440X900 60

FHD 1920X1080 60

HDMI

SDTV 480i 720X480 30

SDTV 576i 720X576 25

EDTV 480p 720X480 60

EDTV 576p 720X576 50

HDTV 720p 1280X720 50 / 60

HDTV 1080i 1920X1080 25 / 30

HDTV 1080p 1920X1080 50 / 60

INPUT SIGNAL MODE TABLE

Installation and User's Guide

Page is loading ...

Orion RNK55NHF Installation and User Manual

Brand: Orion

Model: RNK55NHF

Category: LED displays

Type: Installation and User Manual

Download PDF

report

Orion RNK55NHF Installation and User Manual

Orion RNK55NHF Installation and User Manual

Other documents