Page is loading ...
Assembly Instruction Manual
Special Edition
Multipurpose Rack
Thank you very much for purchasing the
OKAMURA Study DESK. Before using this
product, carefully read this Assembly
Instruction Manual in order to fully under-
stand and correctly assemble the product.
Assembly Final Drawing
(Name of each part)
A cross slot
screwdriver is required for
assembly. Please have one available.
* Do not use an electric screwdriver
because it may damage the
product.
Two
persons should
assemble this
product.
Movable divider
Upper unit
Lower unit
Hook hanger
T-shape hook
Caster
(without stopper)
Caster (with stopper) Movable shelf
plate (large)
Drawer
Movable shelf
plate (small)
Center divider
Fixed shelf
S-shape hook
CAUTION Movement in the front-back direction may result in
turnover, causing injury. Move in the lateral direction.
Okamura Corporation
International Sales and Marketing Division
Address: 2-14-27 Akasaka, Minato-ku, Tokyo 107-0052 Japan
Phone : +81-3-5561-4085
Fax : +81-3-5561-4086
Website: http://www.okamura.co.jp/
When the center divider is installed at the middle stageWhen the center divider is installed at the lower stage
Check before assembly.
Locations of Caution Seals
Warning label
(Attached to the fixed
shelf surface)
(Do not remove the warning labels)
Installation Location Reference Example for Movable Shelf Plate/Movable divider
The movable shelf plate and movable divider can be installed in combination with the center divider as shown in the following table.
Determine a completion state, and then carry out assembly work.
Movable shelf
plate (large)
Three stages
Movable divider
Movable divider
Movable shelf
plate (large)
Two stages
Movable
shelf plate
(small)
Four stages
Movable shelf
plate (large)
Three stages
Movable divider
Movable divider Movable divider
Movable shelf
plate (large)
Two stages
Movable
shelf plate
(small)
Four stages
Movable shelf
plate (large)
Three stages
Movable shelf
plate (large)
Two stages
Movable
shelf plate
(small)
Four stages
Movable shelf
plate (large)
Three stages
Movable divider
Movable shelf
plate (large)
Two stages
Movable
shelf plate
(small)
Four stages
Movable shelf
plate (large)
Four stages
Movable shelf
plate (large)
Three stages
Movable divider
Movable shelf
plate (large)
Two stages
Movable
shelf plate
(small)
Four stages
Movable shelf
plate (large)
Three stages
Movable divider
Movable shelf
plate (large)
Two stages
Movable
shelf plate
(small)
Four stages
Movable shelf
plate (large)
Four stages
(* All are spaced with a pitch of 300mm.)
Details of Parts (make sure to check before assembly)
T-shape hook Connecting nut
(M6 × 12mm)
Both-side connecting
bolt (34mm/34mm)
Single-end
connection bolt
(24mm)
Cap for insert nut
Plug cap
(8mm)
S-shape hook
Actual size
Connecting bolt
(M6 × 10mm)
Hook hanger
Actual size
Connecting bolt
(M6 × 35mm)
Shelf plate
receiving dowel
Caster
(with stopper)
Caster
(without stopper)
Spanner (12mm)
Movable divider ×2
Lower unit ×1
Side panel (right and left) ×1 Rear panel ×1
Movable shelf plate (large) ×1 Movable shelf plate (small) ×2Center divider ×1
Fixed shelf plate ×1
Installation of caster
* Set the protective material on the floor and carry out parts installation work on the material so as not to damage the members.
Screw the casters of and into the caster installation holes on the
back of the lower unit bottom plate to install.
When screwing to the end, securely tighten the bolts and nuts with the
spanner of .
Lower unit
Caster (without stopper)
Caster (with stopper)
Product No. seal
(Attached to the
bottom back side)
Use a cross slot screwdriver for assembly.
* An electric screwdriver or electric tool may damage the product,
therefore, use a manual screwdriver.
Center
divider
When the center divider is installed at the middle stageWhen the center divider is installed at the lower stage
Check before assembly.
Locations of Caution Seals
Warning label
(Attached to the fixed
shelf surface)
(Do not remove the warning labels)
Installation Location Reference Example for Movable Shelf Plate/Movable divider
The movable shelf plate and movable divider can be installed in combination with the center divider as shown in the following table.
Determine a completion state, and then carry out assembly work.
Movable shelf
plate (large)
Three stages
Movable divider
Movable divider
Movable shelf
plate (large)
Two stages
Movable
shelf plate
(small)
Four stages
Movable shelf
plate (large)
Three stages
Movable divider
Movable divider Movable divider
Movable shelf
plate (large)
Two stages
Movable
shelf plate
(small)
Four stages
Movable shelf
plate (large)
Three stages
Movable shelf
plate (large)
Two stages
Movable
shelf plate
(small)
Four stages
Movable shelf
plate (large)
Three stages
Movable divider
Movable shelf
plate (large)
Two stages
Movable
shelf plate
(small)
Four stages
Movable shelf
plate (large)
Four stages
Movable shelf
plate (large)
Three stages
Movable divider
Movable shelf
plate (large)
Two stages
Movable
shelf plate
(small)
Four stages
Movable shelf
plate (large)
Three stages
Movable divider
Movable shelf
plate (large)
Two stages
Movable
shelf plate
(small)
Four stages
Movable shelf
plate (large)
Four stages
(* All are spaced with a pitch of 300mm.)
Details of Parts (make sure to check before assembly)
T-shape hook Connecting nut
(M6 × 12mm)
Both-side connecting
bolt (34mm/34mm)
Single-end
connection bolt
(24mm)
Cap for insert nut
Plug cap
(8mm)
S-shape hook
Actual size
Connecting bolt
(M6 × 10mm)
Hook hanger
Actual size
Connecting bolt
(M6 × 35mm)
Shelf plate
receiving dowel
Caster
(with stopper)
Caster
(without stopper)
Spanner (12mm)
Movable divider ×2
Lower unit ×1
Side panel (right and left) ×1 Rear panel ×1
Movable shelf plate (large) ×1 Movable shelf plate (small) ×2Center divider ×1
Fixed shelf plate ×1
Installation of caster
* Set the protective material on the floor and carry out parts installation work on the material so as not to damage the members.
Screw the casters of and into the caster installation holes on the
back of the lower unit bottom plate to install.
When screwing to the end, securely tighten the bolts and nuts with the
spanner of .
Lower unit
Caster (without stopper)
Caster (with stopper)
Product No. seal
(Attached to the
bottom back side)
Use a cross slot screwdriver for assembly.
* An electric screwdriver or electric tool may damage the product,
therefore, use a manual screwdriver.
Center
divider
Installation of connecting bolts
Screw the single-end connection
bolt of into the rear panel of
the upper unit to install.
(2 locations)
Screw the single-end connection bolt of into the
side panel of the upper unit to install. (3 locations on
the right and left sides)
* The height is three-stage selectable. See on page 5
for reference of installation height.
* Make sure to install the insert nuts at the same height of
upper, middle and lower position.
Rear panel
Side panel (right)
Side panel (left)
Upper
Screwing the single-end connection
bolt of by turning clockwise
Fixation of fixed shelf plate
and rear panel of upper unit
Install the shelf plate and rear panel of the upper unit and securely
tighten the screw-type connector. (2 locations)
Fixed shelf plate
Screw-type connector
Securely
tighten.
Rear panel
Installation of side panel
Install the right and left side panels to the shelf plate
assembled in , and securely tighten the screw-type connec-
tor. (6 locations)
* The height of the shelf plate is three-stage selectable depending
on a position where is installed to the side panel. Determine
the height based on the desk to be aligned and the diagram.
Height of shelf plate and type of desk to be aligned
Screw-type connector
Shelf plate
Height 78cm (Pierna)
Height 76cm (Ugo, Novel-L, Sorano, Prettia-L)
Height 73cm (Arco, Novel-E, Tenuto, Prettia-E)
Securely
tighten.
Connection of upper
and lower units
Screw the both-side connecting bolts of to connect the
upper unit and lower unit. (4 locations)
* The upper unit can be
installed backwards.
When installing the upper unit
on the side of the desk for use,
install it backwards.
Installation of center divider
Insert the dowels on the center divider into the dowel holes on
the lower unit shelf plate, and fix with the connecting bolt of
from the back side. (1 location)
* The center divider can also be installed to the lower unit bottom
plate.
Installation of movable shelf plate (small)
Insert the shelf plate receiving dowels of into the lower unit
side panels and screw fixing divider to install. (8 locations)
Place the movable shelf plate (small) on .
Movable shelf plate
(small)
Lower unit
Center divider
Dowel
Screw-type
connector
Securely
tighten.
* Usable at a stage where the center divider is installed
[About screw-type connector]
Screw-type connector
The screw-type connector is
tightened by turning clockwise.
The screw-type connector is
loosened by turning counterclockwise.
Screw-type
connector
Single-end
connection bolt
(Embedded into the members)
When the arrow is set to the single-
end connection bolt, the connecting
bolt is inserted (removed).
Arrow
[About connection bolt]
Single-end
connection bolt
When screwing the
connection bolts into
the insert nuts, make
sure not to tighten
excessively.
The insert nut may be removed,
or the head of the connection bolt
may be broken.
Installation of connecting bolts
Screw the single-end connection
bolt of into the rear panel of
the upper unit to install.
(2 locations)
Screw the single-end connection bolt of into the
side panel of the upper unit to install. (3 locations on
the right and left sides)
* The height is three-stage selectable. See on page 5
for reference of installation height.
* Make sure to install the insert nuts at the same height of
upper, middle and lower position.
Rear panel
Side panel (right)
Side panel (left)
Upper
Screwing the single-end connection
bolt of by turning clockwise
Fixation of fixed shelf plate
and rear panel of upper unit
Install the shelf plate and rear panel of the upper unit and securely
tighten the screw-type connector. (2 locations)
Fixed shelf plate
Screw-type connector
Securely
tighten.
Rear panel
Installation of side panel
Install the right and left side panels to the shelf plate
assembled in , and securely tighten the screw-type connec-
tor. (6 locations)
* The height of the shelf plate is three-stage selectable depending
on a position where is installed to the side panel. Determine
the height based on the desk to be aligned and the diagram.
Height of shelf plate and type of desk to be aligned
Screw-type connector
Shelf plate
Height 78cm (Pierna)
Height 76cm (Ugo, Novel-L, Sorano, Prettia-L)
Height 73cm (Arco, Novel-E, Tenuto, Prettia-E)
Securely
tighten.
Connection of upper
and lower units
Screw the both-side connecting bolts of to connect the
upper unit and lower unit. (4 locations)
* The upper unit can be
installed backwards.
When installing the upper unit
on the side of the desk for use,
install it backwards.
Installation of center divider
Insert the dowels on the center divider into the dowel holes on
the lower unit shelf plate, and fix with the connecting bolt of
from the back side. (1 location)
* The center divider can also be installed to the lower unit bottom
plate.
Installation of movable shelf plate (small)
Insert the shelf plate receiving dowels of into the lower unit
side panels and screw fixing divider to install. (8 locations)
Place the movable shelf plate (small) on .
Movable shelf plate
(small)
Lower unit
Center divider
Dowel
Screw-type
connector
Securely
tighten.
* Usable at a stage where the center divider is installed
[About screw-type connector]
Screw-type connector
The screw-type connector is
tightened by turning clockwise.
The screw-type connector is
loosened by turning counterclockwise.
Screw-type
connector
Single-end
connection bolt
(Embedded into the members)
When the arrow is set to the single-
end connection bolt, the connecting
bolt is inserted (removed).
Arrow
[About connection bolt]
Single-end
connection bolt
When screwing the
connection bolts into
the insert nuts, make
sure not to tighten
excessively.
The insert nut may be removed,
or the head of the connection bolt
may be broken.
Place the movable shelf plate (large) on .
* The movable shelf plate (large) can also be installed to the upper unit.
Installation of movable shelf plate (large)
Screw the shelf plate receiving dowels of into the posi -
tions of the desired dowel holes remaining on the upper
unit and lower unit to install. (4 locations)
Movable shelf plate (large)
Installation of movable
divider
Insert the movable divider obliquely into the long round notch
in the rear panel as shown in the diagram.
When moving the movable divider laterally, raise the front
slightly and then move laterally.
Movable divider
Raise the front slightly and
then move laterally
Installation of hooks
Install the hook hanger of at either the right or
left position shown in the diagram with the con-
necting bolts of and connecting nuts of .
At this time, pass the S-shape hook of through
the hook hanger of in advance.
Install the T-shape hook of to the side panel
with the connecting bolts of and connecting
nuts of . (4 locations)
To Use Safely
This indicates that improper handling due to disregard of this warning may result in injury or
damage to property.
Fully read the instruction manual before assembly, securely tighten the bolts
with a screwdriver, and use all of the assembly parts without leaving any
parts unused to assemble correctly.
When assembling, do not use an electric screwdriver. When any force more
than necessary is applied, the product may be broken or the bolt may not be
removed.
After assembling, fully tighten the product on a flat
surface, and make sure that each part is securely
installed.
There may be some parts and members which are not
used depending on the assembling pattern. Store them in
a safe place as these parts will always be necessary
when re-combining. Purchase parts separately when they
are lost.
Immediately after purchase, this product may emit
adhesive or paint odors. In such a case, sufficiently
ventilate and aerate. Periodically allow for ventilation.
When installing and moving this product, make sure two
persons carry the product without dragging it.
Dragging the product may result in damage to floors.
When the product is installed in a high humidity location, mold, etc., may grow.
Periodically allow for ventilation.
CAUTIONCAUTION
CAUTION
Cautions for assembly
Do not handle this product roughly or use for any other purpose than speci-
fied. Never apply body weight to any point on the product, or ride on it. It
may result in turnover or breakage, and is extremely dangerous.
Cautions for handling
Select a horizontal and stable location for installation. Use in a location
where the floor is inclined or unstable may result in turnover or an accident,
and is dangerous.
Avoid using this product in a location subject to direct sunlight, high
temperatures or high humidity or in a location subject to direct heat and
wind from a heating stove or air conditioner. It may result in alteration,
deformation or discoloration.
Do not place any hot object directly on the product.
It may result in alteration, deformation or discoloration.
Do not rub the product with hard material, and do not
write with a writing instrument such as a ball-point
pen with a hard tip without using a desk mat.
It may result in deformation or flaws.
Periodically inspect for looseness of the bolts and
connecting parts of the members, and securely
re-tighten them when there is any looseness.
Use while there is looseness may result in risks of
deformation, breakage and turnover.
Do not allow the product to become wet and remain wet and do not leave a
wet cloth on the product. It may result in deformation, cracks, swelling,
stains or corrosion of the surface material. When the surface becomes wet,
immediately wipe so that no moisture is left.
Do not attach any seals or cellophane tape, etc., to the product.
It may result in removal of the surface material.
Cautions for installation
To ensure long-term use
Make sure to wipe with a dry and soft cloth along the wood grain. Use with
a wet cloth may result in cracks and swelling. When the product is very
dirty, moisten a soft cloth with a diluted neutral agent (dishwashing soap),
and tightly squeeze it to wipe away dirt completely. And then, wipe with a
soft dry cloth so that no soapy residue remains. When a large amount of
moisture remains, deformation and discoloration may result.
Do not use alcohol-based or thinner-based
solvent/chemical waste cloth or commercial cleaner
since it will damage the surface. It may result in
discoloration, etc.
About care
Make sure to only place an object on the product within the maximum loading mass. Placing an object on
the product heavier than the maximum loading mass may result in turnover or breakage, and is
extremely dangerous.
Fixed shelf withstand load 20kg (Uniformly distributed mass)
* Uniformly distributed mass means placing a mass uniformly on the desktop and shelf plate.
Diluted
solvent
Alcohol-based
solvent
Neutral agent
(dishwashing soap)
Memo Seal
Assembly
Instruction
Manual
Place the movable shelf plate (large) on .
* The movable shelf plate (large) can also be installed to the upper unit.
Installation of movable shelf plate (large)
Screw the shelf plate receiving dowels of into the posi -
tions of the desired dowel holes remaining on the upper
unit and lower unit to install. (4 locations)
Movable shelf plate (large)
Installation of movable
divider
Insert the movable divider obliquely into the long round notch
in the rear panel as shown in the diagram.
When moving the movable divider laterally, raise the front
slightly and then move laterally.
Movable divider
Raise the front slightly and
then move laterally
Installation of hooks
Install the hook hanger of at either the right or
left position shown in the diagram with the con-
necting bolts of and connecting nuts of .
At this time, pass the S-shape hook of through
the hook hanger of in advance.
Install the T-shape hook of to the side panel
with the connecting bolts of and connecting
nuts of . (4 locations)
To Use Safely
This indicates that improper handling due to disregard of this warning may result in injury or
damage to property.
Fully read the instruction manual before assembly, securely tighten the bolts
with a screwdriver, and use all of the assembly parts without leaving any
parts unused to assemble correctly.
When assembling, do not use an electric screwdriver. When any force more
than necessary is applied, the product may be broken or the bolt may not be
removed.
After assembling, fully tighten the product on a flat
surface, and make sure that each part is securely
installed.
There may be some parts and members which are not
used depending on the assembling pattern. Store them in
a safe place as these parts will always be necessary
when re-combining. Purchase parts separately when they
are lost.
Immediately after purchase, this product may emit
adhesive or paint odors. In such a case, sufficiently
ventilate and aerate. Periodically allow for ventilation.
When installing and moving this product, make sure two
persons carry the product without dragging it.
Dragging the product may result in damage to floors.
When the product is installed in a high humidity location, mold, etc., may grow.
Periodically allow for ventilation.
CAUTIONCAUTION
CAUTION
Cautions for assembly
Do not handle this product roughly or use for any other purpose than speci-
fied. Never apply body weight to any point on the product, or ride on it. It
may result in turnover or breakage, and is extremely dangerous.
Cautions for handling
Select a horizontal and stable location for installation. Use in a location
where the floor is inclined or unstable may result in turnover or an accident,
and is dangerous.
Avoid using this product in a location subject to direct sunlight, high
temperatures or high humidity or in a location subject to direct heat and
wind from a heating stove or air conditioner. It may result in alteration,
deformation or discoloration.
Do not place any hot object directly on the product.
It may result in alteration, deformation or discoloration.
Do not rub the product with hard material, and do not
write with a writing instrument such as a ball-point
pen with a hard tip without using a desk mat.
It may result in deformation or flaws.
Periodically inspect for looseness of the bolts and
connecting parts of the members, and securely
re-tighten them when there is any looseness.
Use while there is looseness may result in risks of
deformation, breakage and turnover.
Do not allow the product to become wet and remain wet and do not leave a
wet cloth on the product. It may result in deformation, cracks, swelling,
stains or corrosion of the surface material. When the surface becomes wet,
immediately wipe so that no moisture is left.
Do not attach any seals or cellophane tape, etc., to the product.
It may result in removal of the surface material.
Cautions for installation
To ensure long-term use
Make sure to wipe with a dry and soft cloth along the wood grain. Use with
a wet cloth may result in cracks and swelling. When the product is very
dirty, moisten a soft cloth with a diluted neutral agent (dishwashing soap),
and tightly squeeze it to wipe away dirt completely. And then, wipe with a
soft dry cloth so that no soapy residue remains. When a large amount of
moisture remains, deformation and discoloration may result.
Do not use alcohol-based or thinner-based
solvent/chemical waste cloth or commercial cleaner
since it will damage the surface. It may result in
discoloration, etc.
About care
Make sure to only place an object on the product within the maximum loading mass. Placing an object on
the product heavier than the maximum loading mass may result in turnover or breakage, and is
extremely dangerous.
Fixed shelf withstand load 20kg (Uniformly distributed mass)
* Uniformly distributed mass means placing a mass uniformly on the desktop and shelf plate.
Diluted
solvent
Alcohol-based
solvent
Neutral agent
(dishwashing soap)
Memo Seal
Assembly
Instruction
Manual
Assembly Instruction Manual
Special Edition
Multipurpose Rack
Thank you very much for purchasing the
OKAMURA Study DESK. Before using this
product, carefully read this Assembly
Instruction Manual in order to fully under-
stand and correctly assemble the product.
Assembly Final Drawing
(Name of each part)
A cross slot
screwdriver is required for
assembly. Please have one available.
* Do not use an electric screwdriver
because it may damage the
product.
Two
persons should
assemble this
product.
Movable divider
Upper unit
Lower unit
Hook hanger
T-shape hook
Caster
(without stopper)
Caster (with stopper) Movable shelf
plate (large)
Drawer
Movable shelf
plate (small)
Center divider
Fixed shelf
S-shape hook
CAUTION Movement in the front-back direction may result in
turnover, causing injury. Move in the lateral direction.
Okamura Corporation
International Sales and Marketing Division
Address: 2-14-27 Akasaka, Minato-ku, Tokyo 107-0052 Japan
Phone : +81-3-5561-4085
Fax : +81-3-5561-4086
Website: http://www.okamura.co.jp/
/
