Shark AL Robot AV2001WD User guide

Brand: Shark AL Robot

Model: AV2001WD

Category: Robotic vacuum cleaners

Type: User guide

This manual is also suitable for

Wet/Dry Robot Floor Cleaner

VACMOP™

Wet/Dry Robot Floor Cleaner

2000WD Series

OWNER’S GUIDE

sharkclean.comsharkclean.com

WARNING

To reduce the risk of ﬁre, electric shock, injury, or property damage:

IMPORTANT SAFETY INSTRUCTIONS

PLEASE READ CAREFULLY BEFORE USE • FOR HOUSEHOLD USE ONLY

SAVE THESE INSTRUCTIONS

If the charging cable plug does not ﬁt fully into the outlet, reverse the plug. If it still does not ﬁt,

contact a qualiﬁed electrician. DO NOT force into outlet or try to modify to ﬁt.

For the latest warnings and cautions, go to sharkclean.com/robothelp

GENERAL WARNINGS

When using an electrical appliance, basic

precautions should always be followed,

including the following:

1. This appliance consists of a Wet/

Dry Robot Floor Cleaner vacuum and

charging dock with power supply.

These components contain electrical

connections, electrical wiring, and

moving parts that potentially present risk

to the user.

2. Before each use, carefully inspect all

parts for any damage. If a part is damaged,

discontinue use.

3. Use only identical replacement parts.

See replacement accessories page of this

booklet.

4. This Wet/Dry Robot Floor Cleaner

contains no serviceable parts.

5. Use only as described in this manual.

DO NOT use Wet/Dry Robot Floor

Cleaner for any purpose other than those

described in this manual.

6. With exception of ﬁlters, dust cups and

pads, DO NOT expose any parts of the

Wet/Dry Robot Floor Cleaner to water or

other liquids.

USE WARNINGS

7. This appliance can be used by persons

with reduced physical, sensory or mental

capabilities or lack of experience and

knowledge if they have been given

supervision or instruction concerning

use of the appliance in a safe way and

understand the hazards involved.

a) Children shall not play with the

appliance.

b) Cleaning and user maintenance shall

not be made by children without

supervision.

8. Always turn o the robotics vacuum

cleaner before inserting or removing the

ﬁlter, dust bin, or ﬂuid reservoir.

9. DO NOT handle plug, charging dock,

charging cable, or Wet/Dry Robot Floor

Cleaner with wet hands. Cleaning and

user maintenance shall not be made by

children without supervision.

10. DO NOT use the robot without the dust

bin, ﬁlter, and ﬂuid reservoir in place.

11. DO NOT damage the charging cord:

a) DO NOT pull or carry charging

dock by the cord or use the cord as

a handle.

b) DO NOT unplug by pulling on cord.

Grasp the plug, not the cord.

c) DO NOT close a door on the cord,

pull the cord around sharp corners,

or leave the cord near heated

surfaces.

12. DO NOT put any objects into nozzle or

accessory openings. DO NOT use with

any opening blocked; keep free of dust,

lint, hair, and anything that may reduce

airﬂow.

13. DO NOT use if Wet/Dry Robot Floor

Cleaner airﬂow is restricted. If the air

paths become blocked, turn the vacuum

cleaner o and remove all obstructions

before turning on the unit again.

14. Keep all vacuum openings away from

hair, face, ﬁngers, uncovered feet, or

loose clothing.

15. DO NOT use if Wet/Dry Robot Floor

Cleaner is not working as it should,

or has been dropped, damaged, left

outdoors, or dropped into water.

16. DO NOT place vacuum cleaner on

unstable surfaces,

17. If robot is placed in a room, and it is not

starting from the dock, the robot must

be placed in an unobstructed circle of 1.5

ft. (45 cm) away from edges and clis.

18. DO NOT use to pick up:

a) Liquid spills

b) Large objects

c) Hard or sharp objects (glass, nails,

screws, or coins)

d) Large quantities of dust (drywall

dust, ﬁreplace ash, or embers).

DO NOT use as an attachment to

power tools for dust collection.

e) Smoking or burning objects (hot

coals, cigarette butts, or matches)

f) Flammable or combustible

materials (lighter ﬂuid, gasoline,

or kerosene)

g) Toxic materials (high

concentrations of chlorine bleach

liquid, high concentrations of

ammonia, or drain cleaning

solution)

19. DO NOT use in the following areas:

a) Outdoor areas near ﬁreplaces with

unobstructed entrances

b) Spaces that are enclosed and may

contain explosive or toxic fumes

or vapors (lighter ﬂuid, gasoline,

kerosene, paint, paint thinners,

mothprooﬁng substances, or

ﬂammable dust

c) In an area with a space heater

d) Near ﬁreplaces with unobstructed

entrances

20. Turn o the Wet/Dry Robot Floor

Cleaner before any adjustment, cleaning,

maintenance or troubleshooting. Note: in

the OFF (O) position, the robot still uses

a small amount of power.

21. Allow all ﬁlters to air-dry completely

before replacing in the Wet/Dry Robot

Floor Cleaner to prevent liquid from

being drawn into electric parts.

22. DO NOT modify or attempt to repair

the Wet/Dry Robot Floor Cleaner or the

battery yourself, except as indicated in

this manual. DO NOT use the vacuum if it

has been modiﬁed or damaged.

23. Remove all spilled or leaked liquid from

the dock landing mat, base or ﬂoor, as it

could lead to risk of electrical shock.

24. Try on an inconspicuous small area of

the ﬂoor, a little bit of the VACMOP™

cleaning solution to ensure it does not

aect the ﬂoor.

25. When reﬁlling the reservoir, check for

leaks, as pooled liquids are a slipping

hazard and may cause electrical shock.

If the reservoir is damaged, it must be

replaced.

26. Use caution walking on mopped ﬂoors,

as they may be slippery while damp.

27. For your robot's cli sensors to work

properly, all runners, rugs, carpets, or

small thresholds (like child gates) must

be 8 inches from any stairs (or must be

continuous and extend over the edge

of the stairs). If a runner, rug, carpet, or

small threshold that is less than 8 inches

from the stairs cannot be moved, you

must use a no-go zone or a BotBoundary

strip to block o the stairs. BotBoundary

strips are not included with your robot.

BATTERY USE

28. The battery is the power source for

the vacuum. Carefully read and follow

all charging instructions.

29. To prevent unintentional starting, ensure

the vacuum is powered o before picking

up or carrying the vacuum. DO NOT

carry the appliance with your ﬁnger on

the power switch.

30. Use O NLY the Shark® charging dock

XDCKRV2000 and use only battery

RVBAT850A. Use of batteries or battery

chargers other than those indicated may

create a risk of ﬁre.

31. Keep the battery away from all metal

objects such as paper clips, coins, keys,

nails, or screws. Shorting the battery

terminals together increases the risk of

ﬁre or burns.

32. Under abusive conditions, liquids may be

ejected from the battery. Avoid contact

with this liquid, as it may cause irritation

or burns. If contact occurs, ﬂush with

water. If liquid contacts eyes, seek

medical help.

33. Robotic vacuum cleaner should not be

stored, charged, or used at temperatures

below 50°F (10°C) or above 104°F

(40°C). Ensure the battery and vacuum

have reached room temperature before

charging or use. Exposing the robot

or battery to temperatures outside of

this range may damage the battery and

increase the risk of ﬁre.

34. DO NOT expose the Wet/Dry Robot

Floor Cleaner or battery to ﬁre or

temperatures above 265°F (130°C) as it

may cause explosion.

35. Non-rechargeable batteries cannot

be recharged.

NO-GO ZONES AND BOTBOUNDARY® STRIPS

36. DO NOT put BotBoundary strips

underneath carpet or rugs.

37. DO NOT place BotBoundary strips on

top of one another.

38. Always use no-go zones or BotBoundary

strips around reﬂective ﬂooring and

surfaces.

39. No-go zones or BotBoundary strips

should always be used near carpeted

stairs.

40. DO NOT use no-go zones or

BotBoundary strips strips within 10 feet

of the dock.

41. For your robot's cli sensors to work

properly, all runners, rugs, carpets, or

small thresholds (like child gates) must

be 8 inches from any stairs (or must be

continuous and extend over the edge

of the stairs). If a runner, rug, carpet, or

small threshold that is less than 8 inches

from the stairs cannot be moved, you

must use a no-go zone or a BotBoundary

strip to block o the stairs.

LASER WARNING

42. This product has a Class 1 laser. It is

safe under reasonably foreseeable

conditions (as deﬁned in this Owner's

Guide.) Always turn o the power before

lifting the robotic vacuum cleaner or

performing any maintenance on it.

43. DO NOT look directly into laser.

sharkclean.comsharkclean.com

GETTING TO KNOW YOUR SHARK® AI ROBOT VACMOP™ GETTING TO KNOW YOUR SHARK® AI ROBOT VACMOP™

Clean Button

Front Bumper

Fluid Reservoir

Error Indicator Light

Charge Indicator Lights Wi-Fi Indicator Light

Cli and Boundary Sensors

Charging Contact

Side Brush

Battery Door

Self-Cleaning

Brushroll Drive Wheel

Dust Bin and Filter

Front Caster

Wheel

Dock Button

Mopping

Indicator Light

Power Button

Charging Dock

DOCK FRONT

FLUID RESERVOIR

DOCK LANDING MAT

(This side up)

DOCK BOTTOM

Charging Contacts

Fill Port

Pad Slot

Removal Buttons

Charger Cord Wrap

Brushroll Door

sharkclean.comsharkclean.com

DOCK SETUP

INSTALLING THE SIDE BRUSHES

Snap the 2 included Side Brushes onto the square

pegs on the bottom of the robot.

If the robot has no charge or it cannot return to the

dock, manually place it on the dock. The indicator

light will turn blue and the robot will beep when it

is correctly placed on the dock.

When the cleaning cycle is complete, or if the battery

is running low, the robot will search for the dock.

If the robot doesn't return to dock, its charge may

have run out, or if it is in wet cleaning mode, the

dock may be blocked by carpet.

CHARGING

IMPORTANT: The Shark® AI Robot VACMOP™ has a pre-installed rechargeable battery. Charge the battery

completely before ﬁrst use. It may take up to 6 hours to fully charge.

To charge, place the robot on the dock. The Power

button on the side of the robot must be in the ON

position (I). The robot will beep when charging begins

and the charging indicator on the dock will turn from

green to blue.

NOTE: When manually placing the robot on the dock, make sure the Charging Contacts on the bottom of the robot are

touching the ones on the dock. While the robot is charging, both white LED lights will ﬂash. When charging is complete,

both white lights will illuminate steadily.

NOTE: When picking up the robot, be careful not to place ﬁngers between the bumper and the base of the robot.

5 ft.

3 ft.

• Select a permanent location with strong Wi-Fi for the Charging Dock, because every time you relocate it,

your robot will have to completely re-map your house.

• Place the dock with its back against a wall and attach the landing mat. Select a level surface on bare ﬂoor,

in a central area. Do not place dock against baseboards or heating elements.

• Remove any objects that are closer than 3 feet from either side of the dock, or closer than 5 feet from the

front of the dock.

• Plug in the dock. The indicator light will illuminate green when the dock has power.

sharkclean.comsharkclean.com

CHARGE INDICATOR LIGHTS BUTTONS AND INDICATOR LIGHTS

DOCK BUTTON

Press to stop cleaning and

send robot back to the

charging dock.

CHARGE INDICATOR LIGHTS

Display the amount of charge

remaining in the battery.

WET MOPPING INDICATOR

LIGHT

Illuminates when ﬂuid

reservoir is properly installed.

Droplet icon will turn red

if there is no ﬂuid in the

reservoir. After 15 minutes,

the robot will return to dock

if reservoir is not ﬁlled.

“!” ERROR INDICATOR

See Troubleshooting section

for full list of error codes.

WI-FI INDICATOR

White light: connected to

Wi-Fi.

Red light: not connected.

Flashing White: setup mode.

No light: not set up yet.

CLEAN BUTTON

Press to begin a cleaning

session. Press again to stop.

IMPORTANT: Before cleaning an entire room for the ﬁrst time, we recommend that you ﬁrst test your robot on a small

section of the ﬂoor to ensure there is no scratching.

NOTE: If the low charge light is blinking red, there is not enough battery power for the robot to return to the dock.

Manually place the robot on the dock.

TIP: To preserve battery life, turn o the power switch if the robot will not be used for a long period of time. The robot

should be recharged at least once every three months. The switch must be in the ON position to charge the robot.

The white charge indicator lights show how much

battery power is remaining.

While the robot is charging, both white LED lights

will ﬂash. When charging is complete, both white

lights will illuminate steadily. It may take up to 6

hours to fully charge your robot.

If the robot is idle and away from the charging

dock for 10 minutes, it will enter Sleep Mode. The

indicator lights will turn o, but the battery and

Wi-Fi lights will remain on in sleep mode. Wake up

the robot by pressing any button.

In Use

Full

Charge

(White)

Partial

Charge

(White)

Low

Charge

(Red)

While

Charging

(White)

No Charge

or O

RECHARGE & RESUME

Press and hold the CLEAN

button for 15 seconds to

turn Recharge & Resume

ON or OFF.

The Recharge & Resume function is turned OFF by

default. Turn ON Recharge & Resume for complete

coverage if your home's ﬂoor plan is bigger than

1500 sq. ft. Your robot will return to the dock,

recharge, and can pick up where it left o.

sharkclean.comsharkclean.com

PREP YOUR HOME USING THE SHARK® AI ROBOT VACMOP™

IQ NAVIGATION™ AND AI LASER VISION

After setup is complete, follow instructions in the

app to help your robot conduct an Explore Run to

create an initial map of your home.

The robot will travel from room to room to identify

walls, furniture, and other obstacles as it cleans.

This run will take less time than a full cleaning, as it

doesn’t cover the entire ﬂoor.

MANUAL CLEANING MODE

To manually start a cleaning cycle, press the Clean button on the robot or on the mobile app. To

immediately send the robot back to the dock, press the Dock button.

IMPORTANT: Before cleaning an entire room for the ﬁrst time, we recommend that you ﬁrst test your robot on a small

section of the ﬂoor to ensure there is no scratching.

NOTE: Scheduling is one of many features that can only be done in the app.

Your robot uses an array of sensors to navigate around walls, furniture legs, and other obstacles while it

cleans. To prevent the robot from entering areas you don't want it to, set up no-go zones in the app. For

best results, prepare your home as indicated below, and schedule a daily cleaning to ensure all ﬂoor areas

are regularly maintained.

NOTE: Be sure to charge the robot completely before

its ﬁrst cleaning so that it can explore, map, and clean

as much of your home as possible. It may take up to 6

hours to fully charge your robot.

NOTE: Avoid moving the dock. If it is relocated, the

robot may not be able to ﬁnd its way back to the dock.

If the robot is relocated while in use, it may not be able

to follow its intelligent cleaning path, or ﬁnd its way

back to the dock.

OBSTRUCTIONS

Clear cords and small objects

less than 2.8" in height, and

open interior doors to ensure

a complete map of your

home.

SCHEDULING

Schedule whole-home

cleanings with the app. To

schedule a mopping run with

the app, the reservoir must

be ﬁlled and installed in the

robot with the pad attached.

THRESHOLDS

Your robot can climb over

most thresholds to get from

room to room, but if one is

too high, set up a no-go zone

in the app to block it o.

AVOID MOVING THE

ROBOT & DOCK

While your robot is cleaning,

do not pick it up and move it,

or move the charging dock—

this will impact the robot’s

navigation and ability to

return to dock when cleaning

is complete.

REMOVE RUGS FROM

DOORWAYS WHEN

MOPPING

Before mopping, you must

set up Carpet Detection in

the app, and move any car-

pets or rugs that block access

to ﬂoors that you want your

robot to mop.

STAIRS

For your robot's cli sensors

to work properly, all runners,

rugs, carpets, or small

thresholds (like child gates)

must be 8 inches from any

stairs (or must be continuous

and extend over the edge of

the stairs). If a runner, rug,

carpet, or small threshold

that is less than 8 inches

from the stairs cannot be

moved, you must use a no-go

zone or a BotBoundary strip

to block o the stairs.

The robot's object detection technology helps it

navigate around obstacles taller than 2.8" in height.

Clear away small objects that may interfere with the

cleaning path of your robot.

Create no-go zones in the app to block o areas you

do not want the robot to enter. You can set up no-go

zones around small objects, or use them to block o

large areas.

VACUUM ONLY INSTRUCTIONS

To vacuum, the ﬂuid reservoir must NOT be

attached to the robot. Make sure the dust bin is

properly installed.

sharkclean.comsharkclean.com

USING THE SHARK® AI ROBOT VACMOP™USING THE SHARK® AI ROBOT VACMOP™

WET MOPPING SETUPWET MOPPING SETUP

Secure the pad to the back of the reservoir.

Lift open the ﬁll cap on the top of the reservoir.

Fill with VACMOP cleaning solution, or room

temperature water, to the MAX ﬁll line. Close the cap

and make sure it is properly sealed.

Attach the mop pad by inserting the ﬂat edge of the

pad through the slot in the reservoir. Pull the mop pad

all the way through the slot until it is securely inserted.

NOTE: Before it can mop, the robot MUST complete its Explore Run and an initial vacuuming run, and Carpet

Detection must be set up in the app.

Firmly push the reservoir into the back of the robot,

behind the dust bin, and ensure both latches click

into place. The water droplet icon on the robot

will illuminate white when the reservoir is inserted

properly.

When the reservoir has ﬂuid and is properly installed,

with the mop pad attached, the robot is ready to

vacuum and mop simultaneously. Press the Clean

button on the robot or in the app to start a vacuuming

and mopping run. The robot will prime the mop pad

for 30 seconds before starting its run.

When mopping is complete, remove the reservoir by

pressing both buttons and sliding it out. Empty the

reservoir after each use.

CAUTION: Floors may be slippery after mopping.

Before your robot’s ﬁrst mopping run, set up Carpet

Detection in the app. This ensures your robot will

avoid carpets and rugs when mopping. Follow the

instructions in the app to help the robot complete its

Explore Run, and then an initial vacuuming run. Once

the robot completes these runs, it will create a map in

the app, and you can select other areas for the robot

to avoid when mopping.

To remove the mop pad from the reservoir, detach

the pad from the back of the reservoir and slide the

pad out of the slot.

NOTE: When mopping, your robot may travel over ﬂoor mats or rugs. Before the next mopping run, move

rugs or mats out of the robot’s path, or use the app to enable Carpet Detection or to set up no-go zones.

sharkclean.comsharkclean.com

MAINTENANCE

EMPTYING THE DUST BIN

With the ﬂuid reservoir removed, press the Dust Bin

Release Button and slide out the dust bin.

CAUTION: Turn o power before performing any maintenance.

NOTE: Even when the switch is in the OFF (O) position, the robot still uses a

small amount of power.

To open the dust bin lid, press and hold the button

while lifting the lid, using the ﬁnger slots.

Empty debris and dust into trash. Wash dust bin if

necessary, using water only.

USING THE SHARK® AI ROBOT VACMOP™

NOTE: Make sure to insert the dust bin completely, until

it clicks into place.

To avoid mold, clean the area between the ﬁlter

and the plastic shield after every mopping run, and

periodically after vacuuming. Remove the shield

and clear any debris buildup with a dry cloth or

soft brush.

WI-FI TROUBLESHOOTING

• To use the app, your phone must be connected

to a 2.4GHz network. The app will only work on a

2.4GHz network.

• Typical home Wi-Fi networks support both 2.4GHz

and 5GHz.

• Do not use a VPN or a proxy server.

• Make sure Wi-Fi isolation is turned o on the

router.

• If you cannot connect, call 1-855-460-5425.

ERROR CODE PROBLEM

! (RED) + Wi-Fi indicator (RED Flashing) Wrong password for Wi-Fi

! (Flashing red) + Wi-Fi (RED) SSID cannot be found, try connecting again

Wi-Fi (RED Flashing) Cannot connect to Wi-Fi

USING THE SHARKCLEAN™ APP AND VOICE CONTROLS

SETTING UP VOICE CONTROL WITH THE GOOGLE ASSISTANT OR AMAZON ALEXA

Visit sharkclean.com/app for setup instructions which include how to enable Shark Skill for Amazon Alexa

and using with Google Assistant.

Google Assistant:

“OK Google, tell Shark to start cleaning.”

“OK Google, tell Shark to pause my robot.”

“ OK Google, tell Shark to send my robot to

the dock.”

Amazon Alexa:

“Alexa, tell Shark to start cleaning.”

“Alexa, tell Shark to pause my robot.”

“ Alexa, tell Shark to send my robot to

the dock.”

Please visit sharkclean.com/app or call 1-855-460-5425 for answers to all your app questions.

Get the most out of your Shark AI Robot VACMOP with these app features:

• Recharge and Resume

Enable this feature to handle

multi-room cleaning in larger

homes. The robot will return

to the dock, recharge, and

can pick up where it left o.

• Carpet Detection

Once the robot has mapped

your home, activate Carpet

Detection in the app to

identify carpets and rugs for

the robot to avoid when it

mops.

• Scheduling

Set whole-home cleanings

for any time, any day.

• Control From Anywhere

Wherever you are, you’re in

control of your robot.

• Cleaning Reports

Each time your robot cleans,

your app will generate a

cleaning report.

Search for SharkClean in the app store and download the app to your iPhoneTM or AndroidTM.

RUMPELSTILTSKIN

Schedule History

EDIT OPTIONS

MapsControl

Shark

Kitchen

Living Room

Dining Room

sharkclean.comsharkclean.com

MAINTENANCE

CLEANING AND REPLACING THE FILTER

Remove and empty the dust bin. Clean any hair or

debris o the Anti-Tangle Comb on the back of

the dust bin.

Pull ﬁlter out of the dust bin by the tabs.

Lightly tap the ﬁlter to remove debris every time

you empty the dust bin. For a deeper clean, rinse

the ﬁlter with water once a month. Allow the ﬁlter

to air-dry for up to 24 hours before reinstalling. Do

not use soap or scrub the ﬁlter. This will damage

the material.

Reinsert the ﬁlter into the dust bin, then slide the

dust bin back into the robot until it clicks into

place.

For optimal suction power, after each use, clean and reinsert the ﬁlter inside the robot's dust bin.

See sharkaccessories.com for replacement ﬁlters.

SELF-CLEANING BRUSHROLL

MAINTAINING THE RESERVOIR AND MOPPING PAD

MAINTENANCE

The Self-Cleaning Brushroll actively removes hair wrap while your robot cleans. If some debris remains

wrapped around the brushroll, continue to run the robot to give the brushroll time to clean itself. If some hair

wrap or debris remains after continued cleaning, carefully remove it from the brushroll.

To clean pads, machine wash warm with light

colors. Use mild detergents and do not use bleach

or fabric softeners. Air-dry, or tumble-dry on low

with no dryer sheets.

Empty the reservoir after each use. Rinse the

reservoir and let it air-dry. DO NOT put the reservoir

in the dishwasher.

To access the brushroll, push up on the tabs on the

brushroll door, then lift o the door.

Lift out the brushroll and remove any debris.

Reinstall the brushroll, inserting the ﬂat end ﬁrst.

Close the brushroll door and press down until both

sides click into place.

NOTE: Replace brushroll every 6 to 12 months, or when visibly worn. See sharkaccessories.com for replacement parts.

NOTE: Replace the ﬁlter once a year for optimal performance.

NOTE: Before storing, make sure the reservoir and pad are completely dry. Store the reservoir and pad in a dry place to

prevent damage.

sharkclean.comsharkclean.com

CLEANING SENSORS AND CHARGING CONTACTS

CLEANING SIDE BRUSHES

MAINTENANCE

Carefully unwind and remove any string or hair

wrapped around brushes.

Gently wipe brushes with a dry cloth. To reinstall,

snap the brushes over the pegs. Spin the brushes

manually to make sure they are installed correctly.

CLEAN SENSORS AND CHARGING CONTACTS AS NEEDED. With a dry cloth, gently dust o the sensors

and contacts located on the bottom of the robot and on the dock.

NOTE: Remove and replace any side brushes that are bent or damaged. To remove a brush, lift it o its peg.

IMPORTANT: The robot uses cli sensors to avoid stairs and other steep drops. Sensors may work less eectively when

they are dirty. For best results, clean sensors regularly.

CLEAN SIDE BRUSHES AS NEEDED.

CLEANING THE WHEELS

MAINTENANCE

CLEAN FRONT WHEEL PERIODICALLY.

See sharkaccessories.com for replacement parts.

Clean the wheel housing. Periodically clean the drive wheels and the housing

around them. To clean, rotate each drive wheel

while dusting.

NOTE: Brush not included.

sharkclean.comsharkclean.com

REPLACEMENT PARTS MAINTENANCE

ERROR CODE SOLUTION

CLEAN (RED) + ! (RED) ﬂashing

Suction motor failure. Remove and empty the dust bin,

clean the ﬁlters, and remove blockages to ensure nothing is

reducing suction.

CLEAN (RED) ﬂashing Robot may be stuck on an obstacle. Move robot to a new

location on a level surface.

DOCK (RED) ﬂashing Front bumper may be jammed. Clean the bumper and make

sure it moves in and out freely.

CLEAN (WHITE) + DOCK (RED) solid BotBoundary® error. Move your robot to a ﬂat surface away

from the magnetic boundary strip and try cleaning again.

CLEAN (RED) + DOCK (WHITE) ﬂashing Cli sensor error. Move your robot to a new location and

clean its cli sensors.

CLEAN (RED) + DOCK (RED) ﬂashing Robot dust bin has been removed and needs to be

reinserted.

DOCK (RED) + ! (RED) ﬂashing Side brush is stuck. Remove any debris from around the side

brushes.

CLEAN (RED) + DOCK (RED) + ! (RED) ﬂashing A drive wheel is stuck. Clean the wheels and remove any

debris wrapped around the axles.

CLEAN (WHITE) + DOCK (RED) + ! (RED) ﬂashing Wheel motor encoder failure. Please turn the power o and

back on.

CLEAN (WHITE) + ! (RED) ﬂashing Blockage in brushroll. Remove any debris from around the

brushroll.

CLEAN (RED) + DOCK (WHITE) + ! (RED) ﬂashing Robot has encountered an error while booting. Please turn

the power o and back on.

CLEAN (WHITE) + DOCK (RED) ﬂashing Robot cannot locate dock. Please pick up your robot and place

it on the dock.

BATTERY ICON (RED) ﬂashing Battery is critically low and needs recharging. If your robot

is unable to dock, place the robot manually on the dock.

CLEAN (RED) + DOCK (WHITE) ﬂashing + ! (RED) Robot is stuck. Please move to a level surface.

DROPLET ICON (RED) solid Fluid Reservoir is empty. Reﬁll before cleaning.

TROUBLESHOOTING

If any error lights are illuminated or ﬂashing on your Shark® AI Robot VACMOP™, see the error

code chart below:

For all other issues, please call Customer Service at 1-855-460-5425.

CAUTION: Turn o power before performing any maintenance.

Filter Brushroll

Side Brushes Charging Dock

Robot Dust Bin

Brushroll Door

Mop Pad 2-Pack

Battery

Fluid Reservoir

Dock Landing Mat

Shark® VACMOP™

Multi-Surface Cleaner

Refill 2L Bottle

Shark® VACMOP™

Hardwood Cleaner

Refill 2L Bottle

NOTE: To order replacement parts, filters, and cleaning solution refills, visit sharkaccessories.com.

sharkclean.comsharkclean.com

END-USER LICENSE AGREEMENT FOR SHARKNINJA SOFTWARE

IMPORTANT: PLEASE READ THE TERMS AND CONDITIONS OF THIS LICENSE AGREEMENT CAREFULLY

BEFORE CONTINUING WITH THIS PROGRAM INSTALL OR USE OF THIS PRODUCT: SharkNinja Operating

LLC’s (“SharkNinja”) End-User License Agreement (“EULA”) is a legal agreement between You (either

a single entity or an individual) and SharkNinja for SharkNinja’s Software Applications, including those

installed by You onto your SharkNinja products or already installed on your device, including all ﬁrmware

(referred hereafter as “SN APPS”). By installing, copying, checking a box, clicking a button conﬁrming

your agreement to these terms, or otherwise continuing to use the SN APPS, You agree to be bound by the

terms of this EULA. This license agreement represents the entire agreement concerning SN APPS between

You and SharkNinja, and it supersedes any prior proposal, representation, or understanding between the

parties. If You do not agree to the terms of this EULA, do not install or use the SN APPS or this product.

The SN APPS are protected by copyright laws and international copyright treaties, as well as other

intellectual property laws and treaties.

1. GRANT OF LICENSE. The SN APPS are licensed as follows:

1.1 Installation and Use. SharkNinja grants You the right to download, install, and use SN APPS on the

speciﬁed platform for which the SN APP was designed and in connection with SharkNinja products with

which the SN APPS are designed to operate (“SN Devices”).

1.2 Backup Copies. You may also make a copy of SN APPS downloaded and installed by You for backup and

archival purposes.

2. DESCRIPTION OF OTHER RIGHTS AND LIMITATIONS.

2.1 Maintenance of Copyright Notices. You must not remove or alter any copyright notices on any and all

copies of the SN APPS.

2.2 Distribution. You may not distribute copies of the SN APPS to third parties.

2.3 Prohibition on Reverse Engineering, Decompilation, and Disassembly. You may not reverse engineer,

decompile, or disassemble SN APPS, except and only to the extent that such activity is expressly permitted

by applicable law notwithstanding this limitation.

2.4 Rental. You may not rent, lease, or lend SN APPS without written permission from SharkNinja.

2.5 NOT FOR RESALE SOFTWARE. Applications identiﬁed as “Not for Resale” or “NFR,” may not be resold,

transferred, or used for any purpose other than demonstration, test, or evaluation.

2.6 Support Services. SharkNinja may provide You with support services related to SN APPS (“Support

Services”). Any supplemental software code provided to You as part of the Support Services shall be

considered part of SN APPS and subject to the terms and conditions of this EULA.

2.7 Compliance with Applicable Laws. You must comply with all applicable laws regarding use of SN APPS.

3. UPDATES. SharkNinja may provide You with upgrades or updates to SN APPS. This EULA will govern

any upgrades provided by SharkNinja that replace and/or supplement SN APPS, unless such upgrade is

accompanied by a separate EULA, in which case the terms of that EULA will govern. If You decide not to

download and use an upgrade or update provided by SharkNinja, You understand that You could put SN

Apps at risk to serious security threats or cause SN Apps to become unusable or unstable.

4. DATA AND PRIVACY. SharkNinja is committed to ensuring your privacy by adhering to high standards

of fairness and integrity. We are committed to keeping our customers informed about how we use the

information we gather from You through the use of each of our websites or SN APPS. Our privacy practices

are described in SharkNinja’s Privacy Policy, as well as in separate notices given when an app, product, or

service is purchased or downloaded. By using SN APPs or providing us with your personal information,

You are accepting and consenting to the practices, terms, and conditions described in SharkNinja’s Privacy

Policy. At all times your information will be treated in accordance with the SharkNinja Privacy Policy,

which is incorporated by reference into this EULA and can be viewed at the following URL:

http://www.sharkninja.com/privacypolicy.

5. THIRD-PARTY APPLICATION LIBRARIES AND EMBEDDED SOFTWARE.

5.1 You acknowledge that Ayla Networks, Inc. (“Ayla”) has provided certain application libraries that have

been embedded into SN APPS (“Ayla Application Libraries”) and enables SN Devices to connect to the Ayla

Cloud Service (“Ayla Embedded Software”).

5.2 You will not use the Ayla Application Libraries except as an incorporated portion of SN APPS,

unmodiﬁed from the form provided to You.

5.3 You will not use the Ayla Embedded Software except as an incorporated portion of SN Devices,

unmodiﬁed from the form provided to You.

5.4 You will not modify, adapt, translate, or create derivative works based on, or decompile, disassemble,

reverse engineer, or otherwise attempt to derive the source code or underlying algorithms of, the Ayla

Application Libraries or the Ayla Embedded Software.

5.5 SharkNinja retains all ownership of SN APPS (and the Ayla Application Libraries contained therein) and

any software installed on SN Devices (including the Ayla Embedded Software) and only a license thereto is

granted to You for use in connection with the SN APPS and SN Devices.

END-USER LICENSE AGREEMENT FOR SHARKNINJA SOFTWARE

5.6 You will not use the Ayla Application Libraries or Ayla Embedded Software to attempt to gain

unauthorized access to or use of the systems/services of SharkNinja’s other licensors; nor will You transmit

viruses, worms, Trojan horses, time bombs, spyware, malware, cancelbots, passive collection mechanisms,

robots, data mining software, or any other malicious or invasive code or program into the systems/services

of SharkNinja’s other licensors.

5.7 You will not use the Ayla Application Libraries or Ayla Embedded Software to interfere with, breach,

or circumvent any security feature, authentication feature, or any other feature that restricts or enforces

limitations on the use of, or access to, the systems/services of SharkNinja’s other licensors.

5.8 You will not probe, attack, scan, or test the vulnerability of the systems/services of SharkNinja’s other

licensors.

5.9 SharkNinja’s other licensors of the SN APPS, Ayla Application Libraries, and the Ayla Embedded

Software are the express third-party beneﬁciaries of this EULA, and the provisions of this Section of this

EULA are made expressly for the beneﬁt of such licensors, and are enforceable by such licensors.

6. TERMINATION. Without prejudice to any other rights, SharkNinja may terminate this EULA if You fail to

comply with the terms and conditions of this EULA. In such event, You must destroy all copies of SN APPS

in your possession.

7. COPYRIGHT. All title, including but not limited to copyrights, in and to SN APPS and any copies thereof

are owned by SharkNinja or its suppliers. All title and intellectual property rights in and to the content

which may be accessed through use of SN APPS are the property of the respective content owner and may

be protected by applicable copyright or other intellectual property laws and treaties. This EULA grants You

no rights to use such content. All rights not expressly granted are reserved by SharkNinja.

8. OPEN SOURCE SOFTWARE. You hereby acknowledge that SN APPS may contain software that is

subject to “open source” or “free software” licenses (“Open Source Software”). The license granted by this

EULA does not apply to Open Source Software contained in the SN APPS. Rather, the terms and conditions

in the applicable Open Source Software license shall apply to the Open Source Software. Nothing in this

EULA limits your rights under, or grants You rights that supersede, any Open Source Software license. You

acknowledge that the Open Source Software license is solely between You and the applicable licensor of

the Open Source Software. To the extent the terms of the licenses applicable to the Open Source Software

require SharkNinja to provide the Open Source Software, in either source or executable form, or to provide

copies of applicable license terms or other required information, You may obtain a copy of the software

by contacting SharkNinja at the below physical address. Additional information about the Open Source

Software, and its terms of use, may be found at www.sharkclean.com/opensource.

9. NO WARRANTIES. SharkNinja expressly disclaims any warranty for SN APPS, Ayla Application Libraries,

or Ayla Embedded Software. SN APPS, Ayla Application Libraries, and Ayla Embedded Software are

provided ‘As Is’ without any express or implied warranty of any kind, including but not limited to any

warranties of merchantability, noninfringement, ﬁtness of a particular purpose, or title. SharkNinja does

not warrant or assume responsibility for the accuracy or completeness of any information, text, graphics,

links, or other items contained within the SN APPS. SharkNinja makes no warranties respecting any harm

that may be caused by the transmission of a computer virus, worm, logic bomb, or other such computer

program. SharkNinja further expressly disclaims any warranty or representation to any third party.

10. LIMITATION OF LIABILITY. In no event shall SharkNinja or its suppliers be liable for any special,

incidental, punitive, indirect, or consequential damages whatsoever (including, but not limited to, damages

for loss of proﬁts or conﬁdential or other information, for business interruption, for personal injury, for

loss of privacy, for failure to meet any duty including of good faith or of reasonable care, for negligence,

and for any other pecuniary or other loss whatsoever) arising out of or in any way related to the use of or

inability to use SN Devices or SN APPS, the provision of or failure to provide support or other services,

information, software, and related content through the product or otherwise arising out of the use of

SN APPS, or otherwise under or in connection with any provision of this EULA, even in the event of the

fault, tort (including negligence), strict liability, breach of contract, or breach of warranty of SharkNinja or

any supplier, and even if SharkNinja or any supplier has been advised of the possibility of such damages.

SharkNinja shall have no liability with respect to the content of the SN APPS or any part thereof, including

but not limited to errors or omissions contained therein, libel, infringements of rights of publicity, privacy,

trademark rights, business interruption, personal injury, loss of privacy, moral rights, or the disclosure of

conﬁdential information.

11. APPLICABLE LAW. The laws of the Commonwealth of Massachusetts will govern this EULA and

You hereby consent to exclusive jurisdiction and venue in the state and federal courts sitting in the

Commonwealth of Massachusetts.

12. ASSIGNMENT. SharkNinja may assign this EULA without notice to Licensor.

13. ENTIRE AGREEMENT. This EULA (including any addendum or amendment to this EULA which is

included with the SN Devices) is the entire agreement between You and SharkNinja relating to the SN

APPS and supersedes all prior or contemporaneous oral or written communications, proposals and

representations with respect to the SN APPS or any other subject matter covered by this EULA. To the

extent the terms of any SharkNinja policies or programs for support services conﬂict with the terms of this

EULA, the terms of this EULA shall control.

If You have questions regarding this EULA, please contact SharkNinja at 89 A Street, Suite 100,

Needham, MA 02494.

sharkclean.comsharkclean.com

ONE (1) YEAR LIMITED WARRANTY

The One (1) Year Limited Warranty applies to purchases made from authorized retailers of SharkNinja

Operating LLC. Warranty coverage applies to the original owner and to the original product only and is

not transferable.

SharkNinja warrants that the unit shall be free from defects in material and workmanship for a period

of one (1) year from the date of purchase when it is used under normal household conditions and

maintained according to the requirements outlined in the Owner’s Guide, subject to the following

conditions and exclusions:

What is covered by this warranty?

1. The original unit and/or non-wearable components deemed defective, in SharkNinja’s sole discretion,

will be repaired or replaced up to one (1) year from the original purchase date.

2. In the event a replacement unit is issued, the warranty coverage ends six (6) months following the

receipt date of the replacement unit or the remainder of the existing warranty, whichever is later.

SharkNinja reserves the right to replace the unit with one of equal or greater value.

What is not covered by this warranty?

1. Normal wear and tear of wearable parts (such as foam ﬁlters, ﬁlters, etc.), which require regular

maintenance and/or replacement to ensure the proper functioning of your unit, are not covered by this

warranty. Replacement parts are available for purchase at sharkaccessories.com.

2. Any unit that has been tampered with or used for commercial purposes.

3. Damage caused by misuse (e.g., vacuuming up water or other liquids), abuse, negligent handling, failure

to perform required maintenance (e.g., not cleaning the ﬁlters), or damage due to mishandling in transit.

4. Consequential and incidental damages.

5. Defects caused by repair persons not authorized by SharkNinja. These defects include damages caused

in the process of shipping, altering, or repairing the SharkNinja product (or any of its parts) when the

repair is performed by a repair person not authorized by SharkNinja.

6. Products purchased, used, or operated outside North America.

How to get service

If your appliance fails to operate properly while in use under normal household conditions within the warranty

period, visit sharkclean.com/support for product care and maintenance self-help. Our Customer Service

Specialists are also available at 1-855-460-5425 to assist with product support and warranty service options,

including the possibility of upgrading to our VIP warranty service options for select product categories.

Please register your product and have it with you when contacting Customer Service.

SharkNinja will cover the cost for the customer to send in the unit to us for repair or replacement. A fee of

$24.95 (subject to change) will be charged when SharkNinja ships the repaired or replacement unit.

How to initiate a warranty claim

You must call 1-855-460-5425 to initiate a warranty claim. You will need the receipt as proof of purchase.

A Customer Service Specialist will provide you with return and packing instruction information.

How state law applies

This warranty gives you speciﬁc legal rights, and you also may have other rights that vary from state to

state. Some states do not permit the exclusion or limitation of incidental or consequential damages, so the

above may not apply to you.

EXPECTED PERFORMANCE

Expected runtime: 60 minutes

Expected charging time: 6 hours

TIP: You can ﬁnd the model and serial

numbers on the QR code labels on the

bottom of the robot and battery.

RECORD THIS INFORMATION

Model Number: ��

Date Code: ��

Date of Purchase: ��

(Keep receipt)

Store of Purchase: ��

registeryourshark.com

BATTERY REMOVAL AND DISPOSAL

This product uses a battery. When the battery no longer holds a charge, it should be removed from the vacuum and recycled. DO NOT incinerate or

compost the battery.

When your lithium-ion battery needs to be replaced, dispose of it or recycle it in accordance with local ordinances or regulations. In some areas, it is

illegal to place spent lithium-ion batteries in the trash or in a municipal solid waste stream. Return spent battery to an authorized recycling center or to

retailer for recycling. Contact your local recycling center for information on where to drop o the spentbattery.

For more information on battery removal for disposal, please visit sharkclean.com/batterysupport.

The RBRC™ (Rechargeable Battery Recycling Corporation) seal on the lithium-ion battery indicates that the costs to recycle the battery at the end of

its useful life have already been paid by SharkNinja. In some areas, it is illegal to place spent lithium-ion batteries in the trash or municipal solid waste

stream and the RBRC program provides an environmentally conscious alternative.

RBRC, in cooperation with SharkNinja and other battery users, has established programs in the United States and Canada to facilitate the collection

of spent lithium-ion batteries. Help protect our environment and conserve natural resources by returning the spent lithium-ion battery to an

authorized SharkNinja service center or to your local retailer for recycling. You may also contact your local recycling center for information on where

to drop o the spent battery, or call 1-800-798-7398.

FCC WARNINGS

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to parts 15 of the FCC Rules. These limits

are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can

radiate radio frequency energy and, if not installed and accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio

or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one

or more of the following measures:

n Reorient or relocate the receiving antenna.

n Increase the separation between the equipment and receiver.

n Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.

n Consult the dealer or an experienced radio/TV technician for help.

This Device complies with part 15 of the FCC rules. Operation is subject to the following conditions:

1 This device may not cause harmful interference

2 This device must accept any interference received, including interference that may cause undesired operation.

Changes or modiﬁcations not expressly approved by the party responsible for compliance could void the user’s authority to operate this device.

sharkclean.comsharkclean.com

NOTES NOTES

PLEASE READ CAREFULLY AND KEEP FOR FUTURE REFERENCE.

This Owner's Guide is designed to help you keep your Shark® AI Robot VACMOP™ running at

peak performance.

SharkNinja Operating LLC

US: Needham, MA 02494

CAN: Ville St-Laurent, QC H4S 1A7

1-855-460-5425

sharkclean.com

Illustrations may dier from actual product. We are constantly striving to improve our products;

therefore the speciﬁcations contained herein are subject to change without notice.

For SharkNinja U.S. Patent information, visit sharkninja.com/uspatents

SHARKCLEAN, and VACMOP are trademarks of SharkNinja Operating LLC. RBRC is a trademark of Rechargeable Battery Recycling

Corporation. APPLE, the Apple logo, and iPhone are trademarks of Apple Inc., registered in the U.S. and other countries. APP STORE is a service

mark of Apple Inc., registered in the U.S. and other countries. GOOGLE, GOOGLE ASSISTANT, GOOGLE PLAY, the Google Play logo, and

Android are trademarks of GOOGLE LLC.

RV2000WDSeries�IB�E�MP�REV�Mv30

PRINTED IN CHINA

Shark AL Robot AV2001WD User guide

Brand: Shark AL Robot

Model: AV2001WD

Category: Robotic vacuum cleaners

Type: User guide

This manual is also suitable for

Wet/Dry Robot Floor Cleaner

Download PDF

report

Shark AL Robot AV2001WD User guide

This manual is also suitable for

Shark AL Robot AV2001WD User guide

Other documents