Siemens HG196510ME Owner's manual

Installation instructions

Instructions for use

HG193510ME

HG195510ME

HG196510ME

HG197510ME

HG198210ME

HG198510ME

HG199210ME

HG199510ME

EN

...........

1

Installation instructions 1-22 | Instructions for use 23-90

Installation instructions

Safety precautions ___________________________________________ 3

Before installing _____________________________________________ 4

Appliance........................................................................................................ 4

Guideline for ventilation.................................................................................. 6

Installation __________________________________________________ 7

Fitting the adjustable feet ............................................................................... 7

Fitting the splash guard .................................................................................. 8

Electrical connection _________________________________________ 9

Gas connection _____________________________________________ 11

Converting the gas type ______________________________________ 15

Hotplate burners........................................................................................... 15

Oven burner ................................................................................................. 17

Grill burner.................................................................................................... 20

General nozzle table .................................................................................... 21

Positioning and levelling _____________________________________ 22

2

3

Safety precautions

This manual is valid for several models. Variations in

details for each cooker are possible.

The safe operation of this appliance can only be

guaranteed if it has been professionally assembled

and installed in accordance with these instructions.

The individual who assembled and installed the

appliance is liable for damage or faults resulting from

incorrect assembly or installation.

All installation and adjustment work, as well as the

conversion to a different type of gas must be

undertaken by an authorised expert and carried out in

accordance with the currently applicable rules and

regulations of the local gas and electricity supply

company.

Shut off the supply of electricity and gas before

carrying out any work.

Before installing the appliance, check that the local

conditions (type of gas and pressure) are compatible

with the appliance settings. The permissible

appliance settings can be found on the rating plate.

Electrical appliances must always be earthed.

If an extractor hood is to be fitted, it must be fitted

according to the associated assembly instructions.

Ensure that the hood is fitted at least 650 mm clear of

the hob.

4

Before installing

Read the following information about the appliance

and the guidelines for ventilation.

Appliance

Unpacking Check the condition of the appliance after unpacking

it. Do not connect the appliance if it has been

damaged in transport.

Dispose of packaging in an environmentally-friendly

manner.

The appliance is bolted to the pallet with two bolts.

To release the appliance, proceed as follows:

• Undo the bolts on the rear of the appliance.

• Screw the bolts back into the appliance without

the connecting brackets.

Appliance class This appliance corresponds to the following

appliance classes:

Appliance class Description

Class 1

Non flush-fitted cooker

Class 2 - subclass 1

Cooker immediately adjacent to two

units, consisting of a single unit.

Can also be installed so that the

side walls are accessible.

5

Appliance dimensions Note the specified dimensions.

Adjacent units Adjacent units must be made of non-combustible

material. The fronts of adjacent units must be

resistant to temperatures up to at least 90 °C. If the

appliance is fitted close to other units, the minimum

distances specified in the picture must be maintained.

HG195510ME

A = 95-160 mm

(HG193510ME, HG197510ME, HG198210ME,

HG199210ME: A= 90-145 mm)

B = 820-885 mm

(HG193510ME, HG197510ME, HG198210ME,

HG199210ME: B= 815-870 mm)

HG193510ME, HG196510ME, HG197510ME,

HG198210ME, HG198510ME, HG199210ME,

HG199510ME

6

Rating plate The technical data for the appliance can be found on

the rating plate on the inside of the storage

compartment flap.

Never remove the rating plate from the appliance.

The setting values are specified on a label on the

appliance packaging.

Use the table below to record the product number (E

no.),

production number (FD no.),

factory setting for type of gas and pressure and

if applicable, the type of gas and pressure

conversions.

Guideline for ventilation

This appliance may only be set up in a sufficiently

ventilated room and according to the applicable

regulations and ventilation requirements.

Please note that the air volume required for

combustion must not be below 2 m3/h per kW of

power (see kW total power on the rating plate).

E no. FD no.

After-sales service

Type of gas

Gas pressure

(factory setting)

Type of gas

Gas pressure

(conversion)

7

Installation

This appliance is always supplied with a set of

adjustable feet and, depending on the model, with a

splash guard.

The appliance may also be used without the splash

guard.

Fitting the adjustable feet

Beforehand:

• Remove all parts that are not permanently fixed,

especially the pan supports and burners.

• Remove the accessories from the oven.

Proceed as follows:

• Tilt the appliance by raising one side slightly from

the floor.

• With the plates in position, screw the adjustable

feet into the mounting holes on the underneath of

the appliance.

• Repeat the process on the other side.

You can make the final adjustments to the feet in

order to level the appliance once the gas and

electricity supply have been connected.

If it is necessary to pull the appliance, screw the

adjustable feet in fully. Make the final settings only

when the other installation tasks have been

completed.

8

Fitting the splash guard

Depending on the model.

Proceed as follows:

• Remove the packaging and the protective film

from the splash guard.

• Screw the splash guard onto the rear of the

appliance using the 2 bolts, each with a washer,

retaining washer and nut.

9

Electrical connection

Only a licensed expert may connect the appliance.

The appliance must be installed according to the

most recent IEE regulations (Institute of Electrical

Engineers).

The appliance could become damaged if incorrectly

connected.

Make sure the voltage of the power supply

corresponds to the specified value on the rating plate.

The rating plate can be found on the inside of the

storage compartment flap.

Ensure that the power supply is properly earthed and

that the fuse and the wiring and piping system in the

building can withstand the load from the appliance.

It is recommended that you configure the circuit for

the appliance to 16 A.

When you route the mains cable, make sure that:

• the cable is not trapped or squashed.

• the cable does not come into contact with sharp

edges or cutting edges.

• the cable does not come into contact with parts

that can reach temperatures of more than 50 °C

above room temperature.

10

Connecting the mains

cable

Where the appliance is directly connected to the

power supply, an all-pole isolating switch with a

contact gap is required.

Complete disconnection in compliance with the

conditions specified in overvoltage category III must

be guaranteed.

The earth cable is excluded from this.

Replacing the mains cable The mains cable is replaced via the terminal block.

The mains cable must be of the following type:

• H05RRF

• 3 x 0.75 mm²

• 230 V~

Leave the mains cable slightly overlong so that you

can pull out the appliance for cleaning purposes.

Proceed as follows:

• Open the terminal box.

• Undo the screw on the terminal block that fixes

the cable in place.

• Loosen the screw contacts and replace the cable

with a new one of the same length.

The cable must comply with the stipulated specifi-

cations.

• Connect the yellow-green wire to the < terminal.

This wire must be at least 10 mm longer than the

other wires.

• Connect the blue neutral wire to terminal N.

• Connect the brown power wire to

terminal L.

11

Gas connection

The appliance must be connected in accordance with

the currently applicable regulations.

Before installing the appliance, check that the local

conditions (type of gas and pressure) are compatible

with the appliance settings. The permissible

appliance settings can be found on the rating plate.

Connection to the gas lines and seal fitting must be

carried out professionally according to the currently

applicable standards.

Gas connection on the

appliance

The gas connection (ISO 228-1, 1/2") is located at the

rear left of the appliance.

The following connections are provided with the

appliance:

Default setting of the

burners

The burners are set up for G30 liquefied gas (29

mbar) on delivery.

A nozzle set for G20 natural gas (20 mbar) is supplied

with the appliance.

Connecting

pieces Description

Connecting piece ISO 228-1/ISO

7-1

(and seal)

LPG corrugated tube union

(and seal)

12

Country-specific

connection

Corrugated tube

union

(liquefied gas)

ISO 7-1

(natural gas)

AE X X

AF X X

BD X X

BH X X

DZ X X

EG X X

GH X X

IR X X

JO X X

KW X X

LB X X

LY X X

MA X X

OM X X

PK X X

QA X X

SA X X

SD X X

SY X X

TN X X

YE X X

13

Connecting to liquefied gas If you connect the appliance to liquefied gas,

you must always install a suitable gas pressure

regulator.

Use the total gas consumption of the appliance stated

on the rating plate to select a suitable gas pressure

regulator.

Only use connecting lines or flexible hoses which

comply with the applicable regulations and which are

approved for this purpose.

Proceed as follows:

• Screw the corrugated tube union (C) and the seal

(B) to the gas connection (A).

• Hold the corrugated tube union (C) in place with a

spanner and screw the connecting piece to a

flexible gas connecting hose (E).

• Tighten the clamp (D).

Only use approved sealing compound to seal the

thread.

E

14

Flexible hose If you use flexible hoses, make sure that:

• the hoses do not become trapped or squashed.

• the hoses are not subject to twisting or pulling

forces.

• the hoses do not come into contact with sharp

edges or cutting edges.

• the hoses do not come into contact with parts that

could reach a temperature higher than 70 °C

above room temperature.

Ensure that the full length of the hoses are accessible

for inspection.

Safety valve The installation of a safety valve for opening and

closing the gas supply is a compulsory requirement.

Fit the safety valve between the gas connecting line

to the appropriate room and the hob. Ensure

unhindered access to this valve.

Checking for leaks After connecting the gas line, check the connections

for leaks using soapy water.

Initial use Switch the appliance on as described in the

instruction manual.

Light all the burners and check that the flames remain

stable at both the high and low settings.

15

Converting the gas type

If the appliance is not already set up for the existing

type of gas, the appliance must be converted.

The conversion to a different type of gas must be

carried out by an authorised expert in accordance

with the applicable regulations.

The type of gas and pressure that was preset at the

factory are indicated on the rating plate on the inside

of the storage compartment flap.

In order to convert to a different type of gas, the

nozzles must be replaced and the low flame and

primary air may have to be adjusted.

Hotplate burners

Replacing the nozzles

Proceed as follows:

• Remove the pan supports.

• Remove the burner lids (A) and burner cups (B)

from the burners (C).

• Remove the nozzle (D) and replace it with an

appropriate nozzle for the new type of gas (see

section “General nozzle table”).

• Replace the gas label with the new label that was

supplied with the nozzle set.

A

B

C

D

16

• Place each burner cup (B) on the burner (C).

• Position the relevant burner cap (A) exactly on

top of the cup.

• Refit the pan supports.

Adjusting the low flame Proceed as follows:

• Switch on the burner and turn the control knob

towards the small flame setting.

• Pull off the control knob.

• Adjust the inner setting screw through the gas tap

opening in the control panel until a stable flame is

burning correctly.

Loosen the setting screw to increase the gas flow

or tighten it to decrease the gas flow.

The setting is correct when the height of the small

flame is approx. 3 to 4 mm.

• Refit the control knob.

• Check that the flame does not go out when the

gas flow is quickly changed between maximum

and minimum and vice versa.

A

B

C

17

Oven burner

Replacing the nozzles Proceed as follows:

• Remove the removable floor of the oven by

undoing the 2 screws at the front and pulling the

floor out upwards and towards the front.

• Undo the 2 screws on the right and the screw on

the left of the oven burner and pull the burner

upwards and towards the front slightly.

• Unscrew the nozzle and replace it with a nozzle

which is suitable for the new type of gas (see

"General nozzle table" section).

• Replace the gas label with the new label that was

supplied with the nozzle set.

Reassembling the burner To reassemble the burner, proceed in the opposite

order.

18

Adjusting the low flame Proceed as follows:

• Open the appliance door. Press the control knob

for the oven in and turn it anti-clockwise to the

maximum setting

250.

The gas burner will light. Hold the control knob

depressed for around 15 seconds and then

release it.

• Close the appliance door. Remove the control

knob.

• Through the gas tap opening in the control panel,

loosen the internal setting screw slightly.

• Replace the control knob and heat the oven for

15 minutes.

• Then turn the control knob to the minimum setting

140

.

• Remove the control knob again.

• Now, through the gas tap opening in the control

panel, adjust the internal setting screw until a

stable flame is burning correctly.

Loosen the setting screw to increase the gas flow

or tighten it to decrease the gas flow. The setting

is correct when the height of the small flame is

around 3 to 4 mm.

In the case of a connection to liquefied gas,

tighten the setting screw.

• Refit the control knob.

• Make sure that the flame does not go out when

the gas flow is changed quickly from maximum to

minimum and vice versa, and when the

appliance door is opened and closed.

Page is loading ...

Siemens HG196510ME Owner's manual

This manual is also suitable for

Siemens HG196510ME Owner's manual

Related papers

Other documents