Cooper Atkins 9315 User manual

Cooper Atkins
Brand
Cooper Atkins
Model
9315
Type
User manual

Cooper Atkins 9315 Prover Box allows you to check the calibration of compatible Cooper-Atkins 10K thermistor instruments, including the TM99A/TC100 series, SH series, and SRH77A. With three temperature simulation jacks (32°F, 72°F, and 120°F), you can easily verify the accuracy of your instrument's temperature readings. Simply disconnect the standard temperature probe, install the included double-ended jumper cord, select the desired temperature, and turn on the meter. If the displayed temperature is within the instrument's normal tolerance (±0.3°F), your calibration is confirmed.

Cooper Atkins 9315 Prover Box allows you to check the calibration of compatible Cooper-Atkins 10K thermistor instruments, including the TM99A/TC100 series, SH series, and SRH77A. With three temperature simulation jacks (32°F, 72°F, and 120°F), you can easily verify the accuracy of your instrument's temperature readings. Simply disconnect the standard temperature probe, install the included double-ended jumper cord, select the desired temperature, and turn on the meter. If the displayed temperature is within the instrument's normal tolerance (±0.3°F), your calibration is confirmed.

9315
Prover Box
OPERATING INSTRUCTIONS
LIMITED WARRANTY
Any instrument which proves to be defective in material or workmanship within
one year of original purchase will be repaired or replaced without charge upon
receipt of the unit prepaid with proof of purchase. This Limited Warranty does
not cover damage in shipment or failure caused by tampering, obvious
carelessness, or abuse, and is the purchaser’s sole remedy.
Cooper-Atkins Corporation
33 Reeds Gap Road, Middlefield, CT 06455-0450 U.S.A.
860-347-2256
www.cooper-atkins.com
Intended for use in checking the calibration of Cooper-Atkins 10K
thermistor instruments which include the TM99A / TC100 series, the
SH series, and the SRH77A.
Instructions for use:
1. Disconnect the standard temperature probe from the meter.
2. Install the double-ended jumper cord (provided) into the meter.
3. Insert the opposite end of the double-ended jumper cord into the desired
temperature simulation jack (choose from 32°F, 72°F, and 120°F).
4. Turn the meter on and verify the temperature reading is as expected within
the normal tolerance of the instrument (±0.3°F).
27-958517B
9315
Prover Box
OPERATING INSTRUCTIONS
LIMITED WARRANTY
Any instrument which proves to be defective in material or workmanship within
one year of original purchase will be repaired or replaced without charge upon
receipt of the unit prepaid with proof of purchase. This Limited Warranty does
not cover damage in shipment or failure caused by tampering, obvious
carelessness, or abuse, and is the purchaser’s sole remedy.
Cooper-Atkins Corporation
33 Reeds Gap Road, Middlefield, CT 06455-0450 U.S.A.
860-347-2256
www.cooper-atkins.com
Intended for use in checking the calibration of Cooper-Atkins 10K
thermistor instruments which include the TM99A / TC100 series, the
SH series, and the SRH77A.
Instructions for use:
1. Disconnect the standard temperature probe from the meter.
2. Install the double-ended jumper cord (provided) into the meter.
3. Insert the opposite end of the double-ended jumper cord into the desired
temperature simulation jack (choose from 32°F, 72°F, and 120°F).
4. Turn the meter on and verify the temperature reading is as expected within
the normal tolerance of the instrument (±0.3°F).
27-958517B
9315
Prover Box
OPERATING INSTRUCTIONS
LIMITED WARRANTY
Any instrument which proves to be defective in material or workmanship within
one year of original purchase will be repaired or replaced without charge upon
receipt of the unit prepaid with proof of purchase. This Limited Warranty does
not cover damage in shipment or failure caused by tampering, obvious
carelessness, or abuse, and is the purchaser’s sole remedy.
Cooper-Atkins Corporation
33 Reeds Gap Road, Middlefield, CT 06455-0450 U.S.A.
860-347-2256
www.cooper-atkins.com
Intended for use in checking the calibration of Cooper-Atkins 10K
thermistor instruments which include the TM99A / TC100 series, the
SH series, and the SRH77A.
Instructions for use:
1. Disconnect the standard temperature probe from the meter.
2. Install the double-ended jumper cord (provided) into the meter.
3. Insert the opposite end of the double-ended jumper cord into the desired
temperature simulation jack (choose from 32°F, 72°F, and 120°F).
4. Turn the meter on and verify the temperature reading is as expected within
the normal tolerance of the instrument (±0.3°F).
27-958517B
9315
Prover Box
OPERATING INSTRUCTIONS
LIMITED WARRANTY
Any instrument which proves to be defective in material or workmanship within
one year of original purchase will be repaired or replaced without charge upon
receipt of the unit prepaid with proof of purchase. This Limited Warranty does
not cover damage in shipment or failure caused by tampering, obvious
carelessness, or abuse, and is the purchaser’s sole remedy.
Cooper-Atkins Corporation
33 Reeds Gap Road, Middlefield, CT 06455-0450 U.S.A.
860-347-2256
www.cooper-atkins.com
Intended for use in checking the calibration of Cooper-Atkins 10K
thermistor instruments which include the TM99A / TC100 series, the
SH series, and the SRH77A.
Instructions for use:
1. Disconnect the standard temperature probe from the meter.
2. Install the double-ended jumper cord (provided) into the meter.
3. Insert the opposite end of the double-ended jumper cord into the desired
temperature simulation jack (choose from 32°F, 72°F, and 120°F).
4. Turn the meter on and verify the temperature reading is as expected within
the normal tolerance of the instrument (±0.3°F).
27-958517B
  • Page 1 1

Cooper Atkins 9315 User manual

Cooper Atkins
Brand
Cooper Atkins
Model
9315
Type
User manual

Cooper Atkins 9315 Prover Box allows you to check the calibration of compatible Cooper-Atkins 10K thermistor instruments, including the TM99A/TC100 series, SH series, and SRH77A. With three temperature simulation jacks (32°F, 72°F, and 120°F), you can easily verify the accuracy of your instrument's temperature readings. Simply disconnect the standard temperature probe, install the included double-ended jumper cord, select the desired temperature, and turn on the meter. If the displayed temperature is within the instrument's normal tolerance (±0.3°F), your calibration is confirmed.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents