Chief MAC251 Installation guide

Chief
Brand
Chief
Model
MAC251
Category
Wall & ceiling mounts accessories
Type
Installation guide
INSTALLATION INSTRUCTIONS
Instrucciones de instalación
Installationsanleitung
Instruções de Instalação
Istruzioni di installazione
Installatie-instructies
Instructions d´installation
CPU Adapter
Spanish Product Description
German Product Description
Portuguese Product Description
Italian Product Description
Dutch Product Description
French Product Description
MAC-251
MAC-251 Installation Instructions
2
DISCLAIMER
Milestone AV Technologies and its affiliated corporations and
subsidiaries (collectively "Milestone"), intend to make this
manual accurate and complete. However, Milestone makes no
claim that the information contained herein covers all details,
conditions or variations, nor does it provide for every possible
contingency in connection with the installation or use of this
product. The information contained in this document is subject
to change without notice or obligation of any kind. Milestone
makes no representation of warranty, expressed or implied,
regarding the information contained herein. Milestone assumes
no responsibility for accuracy, completeness or sufficiency of
the information contained in this document.
Chief® is a registered trademark of Milestone AV Technologies.
All rights reserved.
IMPORTANT WARNINGS AND
CAUTIONS!
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure all components are
properly assembled and installed using the instructions
provided.
WARNING: Failure to provide adequate structural strength
for this component can result in serious personal injury or
damage to equipment! It is the installer’s responsibility to
make sure the structure to which this component is attached
can support five times the combined weight of all equipment.
Reinforce the structure as required before installing the
component.
WARNING: Exceeding weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all components does not exceed the maximum allowable
weight of the mount to which the MAC251 is being installed.
DIMENSIONS
13.85
351.91
1.50
38.10 2.50
63.50
12.60
320.16 3.94
100
3.94
100
APPROXIMATE CENTER
OF DISPLAY
13.75
MAXIMUM EQUIPMENT SIZE
349.25
5.94
150.80
1.50
38.10
1.25
31.75
3.88
MAXIMUM EQUIPMENT SIZE
98.43
4.66
ADDED DEPTH TO MOUNT
AND MSB-XXXX INTERFACE
BRACKET
118.39
.88
22.23
2.50
63.50
1.75
44.45
9.00
228.60
NOTE: MOUNT AND CUSTOM INTERFACE
BRACKET NOT SHOWN. SEE DRAWING FOR
MOUNT AND MSB-XXXX FOR ADDITIONAL
TECHNICAL INFORMATION
DIMENSIONS: [MILLIMETER]
INCH
Installation Instructions MAC-251
3
LEGEND
TOOLS REQUIRED FOR INSTALLATION
PARTS
Tighten Fastener
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Loosen Fastener
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Hex-Head Wrench
Llave de cabeza hexagonal
Sechskantschlüssel
Chave de cabeça sextavada
Chiave esagonale
Zeskantsleutel
Clé à tête hexagonale
By Hand
A mano
Von Hand
Com a mão
A mano
Met de hand
À la main
1/8"
(included)
A (1)
C (4)
D (4)
B (1)
10-24 x 1/2"
[CPU Adapter]
[Mounting button]
[6-ft. web strap]
E (1)
1/8"
MAC-251 Installation Instructions
4
ASSEMBLY AND INSTALLATION
Assemble Mounting Buttons to CPU Holder
WARNING: IMPROPER INSTALLATION CAN LEAD TO
CPU ADAPTER FALLING! Mounting buttons must be
securely fastened to device rack.
1. Install four mounting buttons (C) to CPU adapter (A) using
four 10-24 x 1/2" flat head cap screws (D), and a 1/8" hex
wrench (E). (See Figure 1)
Figure 1
Assemble CPU to CPU Adapter
1. Place CPU into CPU adapter (A) making certain
connections on CPU are oriented with cable access
opening in sides of CPU adapter. (See Figure 2)
Figure 2
Assemble Mounting Strap to CPU Adapter
1. Install web strap (B) into CPU adapter, around CPU, and
secure. (See Figure 3)
NOTE: Strap can also be installed so that it wraps around sides
of CPU adapter.
Figure 3
(A)
(C) x 4
1
(D) x 4
1
(A)
CPU
(B)
1
CPU
(A)
Installation Instructions MAC-251
5
Install CPU Adapter with CPU to Mount
WARNING: COMBINED WEIGHT OF CPU AND CPU
ADAPTER MAY WEIGH IN EXCESS OF 40 LBS. ALWAYS
use two people when lifting and follow proper lifting
techniques when installing!
1. While supporting both sides of CPU adapter, align four
mounting buttons on CPU adapter with four mounting holes
in faceplate of mount. (See Figure 4)
Figure 4
2. Lower CPU adapter into place listening for audible "click" to
ensure recessed area of mounting buttons are properly
seated in lower area of mounting holes and latching flag or
"click lock" mechanism on mount has engaged. (See
Figure 4)
WARNING: IMPROPER INSTALLATION CAN LEAD TO
CPU ADAPTER FALLING! Make certain mounting buttons on
CPU adapter are fully engaged in teardrop holes in mount
and latching flag or "click lock" mechanism on mount is fully
closed before installing the display to other side of CPU
adapter.
3. Route wires and cables following the instructions provided
with the mount.
Install Display
WARNING:
DISPLAY MAY WEIGH IN EXCESS OF 40
LBS.
ALWAYS use two people when lifting and follow proper
lifting techniques when installing!
IMPORTANT ! :
The following procedure assumes that the
proper interface bracket for display has already been
installed on display, if required. If no interface bracket is
present on display, install bracket to display before
proceeding, using instructions included with interface
bracket.
1. Make sure latching flag on CPU adapter is in the
UNLATCHED position (See Figure 5).
Figure 5
2. While supporting each side of display, align four mounting
buttons on display or interface bracket with four teardrop
slots in CPU adapter (See Figure 6).
3. Lower display firmly into place. (See Figure 6)
Figure 6
1
2
(MWR mount shown as example)
(MWR)
Latching Flag
UNLATCHED
1
(A) (CPU not shown)
Mounting Button
(On interface bracket
2
or display)
3
(A)
(CPU not shown)
MAC-251 Installation Instructions
6
CAUTION: Latching flag must fully engage mounting
button.
4. Secure display by rotating latching flag to the LATCHED
position. If latching flag does not fully engage, ensure
mounting buttons are fully seated in teardrop slots. (See
Figure 7)
NOTE: A hole is provided in the latching flag and CPU holder
to accommodate insertion of a padlock or similar
locking device.
Figure 7
5. Connect cables to display.
Latching
4
LATCHED
(A)
Mounting Button
(On interface bracket
or display)
flag
CPU
Hole for padlock
or other locking
device
Installation Instructions MAC-251
7
MAC-251 Installation Instructions
Chief Manufacturing, a products division
of Milestone AV Technologies
8804-000316 Rev01
2010 Milestone AV Technologies, a
Duchossois Group Company
www.chiefmfg.com
11/10
USA/International A 8401 Eagle Creek Parkway, Savage, MN 55378
P800.582.6480 / 952.894.6280
F877.894.6918 / 952.894.6918
Europe A Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands
P+31 (0)40 2668620
F+31 (0)40 2668615
Asia Pacific A Office No. 1 on 12/F, Shatin Galleria
18-24 Shan Mei Street
Fotan, Shatin, Hong Kong
P852 2145 4099
F852 2145 4477
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Chief MAC251 Installation guide

Chief
Brand
Chief
Model
MAC251
Category
Wall & ceiling mounts accessories
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents