Elmo EL86R2-KIT Owner's manual

INSTRUCTION MANUAL

xSync Board / ELMO Board

EL55R2/EL65R2/EL75R2/EL86R2

Ver.01

Read this manual carefully before using the product.

Store this manual in a safe place in case you need it again.

 
2 
Table of contents 
1 Before Use ........................................ 7 
1.1 Package Contents ............................ 7 
1.2 Part Names and Functions .............. 8 
1 Front .................................................. 8 
2 Side and Bottom ................................ 9 
3 Touch pen and Eraser ..................... 10 
4 Remote Control ................................11 
◆ Preparation ................................... 12 
1.3 Installation ..................................... 13 
1 Installation Conditions ..................... 13 
◆ Attachment of the Display Monitor   
 to the Stand .................................. 14 
1.4 Turning On or Off the Power ......... 15 
1 Connecting the Power Cord ............ 15 
2 Turning On the Power ..................... 15 
◆ Initial Startup ................................ 16 
3 Turning Off the Power ..................... 17 
4 Standby Mode ................................. 18 
2 Basic Operations ........................... 19 
2.1 Touch Operations .......................... 19 
2.2 Basic Screen Operations .............. 20 
◆ Home Screen ................................ 20 
◆ Shortcuts of Apps .......................... 21 
◆ Uninstallation of Apps ................... 22 
◆ Connection Status Icons on the   
 Home Screen ................................ 23 
◆ Displaying the Side Menu Bar....... 24 
3 Using Apps ..................................... 25 
3.1 Using ELMO Note (Whiteboard).... 25 
◆ Startup .......................................... 25 
◆ Initial Startup ................................ 25 
◆ Basic Operations .......................... 26 
◆ Screen Description ....................... 27 
◆ Pen Menu ...................................... 28 
◆ Eraser menu ................................. 29 
◆ Selection Menu ............................. 29 
◆ Shapes Menu ................................ 30 
◆ Functions Available in the   
 Operation Mode ............................ 30 
◆ Background Menu ......................... 31 
◆ Background Image Menu .............. 31 
◆ Page Operation Menu ................... 32 
◆ Add Page Menu ............................ 32 
◆ Functions Available When   
 Selecting an Object ....................... 33 
◆ Menu Operations .......................... 34 
◆ Split Screen Mode......................... 35 
◆ Saving Images .............................. 36 
3.2 Using Overlay Function ................ 37 
◆ Startup .......................................... 37 
◆ Toolbar Description ....................... 37 
3.3 Using Camera Roll Function ......... 38 
◆ Startup .......................................... 38 
◆ Screen Description ....................... 38 
◆ Comparing Images and Videos ..... 39 
◆ Pasting to ELMO Note   
 (whiteboard) .................................. 39 
3.4 Using a USB Camera ..................... 40 
◆ Startup .......................................... 40 
◆ Screen Description ....................... 40 
◆ USB Camera Settings Screen ....... 41 
3.5 Viewing Web Page (E Browser) .... 42 
◆ Startup .......................................... 42 
◆ Screen Description ....................... 42 
◆ Popup Display Settings ................. 44 
3.6 Using ELMO Timer Function ......... 45 
◆ Startup .......................................... 45 
◆ Basic Operations (Timer) .............. 45 
◆ Basic Operations (Stopwatch) ...... 45 
◆ Creating Tasks using Timer ........... 46 
◆ Timer List Screen .......................... 48 
◆ Task List Screen ........................... 49 
◆ Timer Settings Screen .................. 49 
◆ Minimizing the Screen .................. 50 
◆ Stopwatch Screen ......................... 50 
3.7 Using Wireless Casting Function 
 󲼅Transcreen󲼆 .................................. 51 
◆ Preparation ................................... 51 
◆ Using on Windows OS .................. 52 
◆ Using on iOS or MacOS ................ 52 
◆ Using on Chrome OS .................... 53 
◆ Using on Android OS .................... 53 
◆ Mirroring Screen ........................... 53 
 

 
3 
3.8 Using Anti-Virus Function   
 (Avira Security) .............................. 54 
◆ Startup .......................................... 54 
◆ Initial Startup ................................ 54 
◆ Basic Operations .......................... 54 
3.9 Using ELMO Play ........................... 55 
◆ Startup .......................................... 55 
3.10 Using File Manger Function .......... 56 
◆ Startup .......................................... 56 
◆ Screen Description ....................... 56 
◆ Cloud Account Settings ................. 58 
◆ Uploading Files to Cloud ............... 60 
3.11 Using Utilities Function ................ 61 
◆ Startup .......................................... 61 
◆ Screen Description ....................... 61 
4 Using with External Devices.......... 62 
4.1 Connecting Devices ...................... 62 
◆ Displaying the Computer Screen   
 (Video and Audio) ......................... 62 
◆ Controlling the Product from a   
 Computer (Serial Control) ............. 65 
◆ Displaying the Screen of the   
 Connected Device   
 (Video and Audio) ......................... 66 
◆ Playing the Audio of the Product   
 through Other Devices .................. 66 
◆ Operation ...................................... 67 
◆ Configuring the Source Settings ... 68 
5 Configuring the Settings ............... 70 
◆ Startup .......................................... 70 
◆ Before Configuring the Settings .... 70 
◆ Network and Connection ............... 70 
◆ System Settings ............................ 75 
6 Optional Item .................................. 80 
6.1 Easy Controller .............................. 80 
◆ Easy Controller Buttons ................ 81 
7 Troubleshooting and Maintenance 82 
7.1 Troubleshooting ............................. 82 
◆ The product does not operate   
 properly. ........................................ 82 
◆ The image of the input source   
 cannot be output correctly............. 82 
◆ No audio is output from the   
 speaker. ........................................ 83 
◆ Touch operations do not work   
 properly. ........................................ 83 
◆ Cannot connect to the network. .... 83 
7.2 Maintenance ................................... 84 
◆ Cleaning of the LCD display ......... 84 
8 Specifications ................................ 85 
8.1 Product Specifications .................. 85 
9 After-Sales Service ........................ 87 
9.1 Product Warranty ........................... 87 
9.2 Repair Procedure ........................... 87 
 

4

Make sure to read the “SAFETY INSTRUCTIONS” in this guide before using this product.

WARNING

・Failure to follow the installation instructions included with the display could result in injury and product damage

which may not be covered by the warranty.

・Do not open or disassemble the display.

You risk electrical shock from the high voltage inside the casing. Opening the casing also voids the warranty.

・Do not stand (or allow children to stand) on a chair to touch the surface of the display.

Rather, mount the product at the appropriate height.

・To reduce the risk of fire or electric shock, do not expose the display to rain or moisture.

・If the display requires replacement parts, make sure the service technician uses replacement parts specified

by ELMO or parts with the same characteristics as the original.

・Ensure that any cables that cross the floor to the display are properly bundled and marked to avoid a trip hazard.

・Do not insert objects inside the cabinet ventilation holes,because they could touch dangerous voltage points

andcause electric shock, fire or product damage which may not be covered by the warranty.

・Do not place heavy objects on the power cable. Damage to the cable could cause shock,

fire or product damage which may not be covered by the warranty.

・Use only extension cords and outlets that can fully accommodate the display’s polarized plug.

・Use the power cable provided with the display. If a power cable is not supplied, contact your supplier.

Use only power cables that match the AC voltage of the power outlet and that comply

with your country’s safety standards.

・If the glass is broken, do not touch the liquid crystal.

To prevent injury, handle glass fragments with care when disposing of them.

・Do not move or mount the display by connecting rope or wire to its handles.

The display is heavy, and failure of the rope, wire or handle could lead to injury.

・Use only VESA®-approved mounts if using a mount other than the one supplied with the display.

・Disconnect all of the display’s power cables from the wall outlet and seek assistance

from qualified service personnel if any of the following occur:

* The power cable or plug is damaged. * Liquid is spilled into the display. * Objects fall into the display.

* The display is dropped. * Structural damage, such as cracking, occurs

* The display behaves unexpectedly when you follow operating instructions

CAUTION

・Turn off the display before cleaning its screen.

Otherwise, you may scramble the desktop icons or inadvertently activate applications when you wipe the screen.

・Avoid setting up and using the display in an area with excessive levels of dust, humidity, and smoke.

・Make sure an electrical socket is near the display and remains easily accessible during use.

・The display should be used only with European TN and TT power distri bution systems.

It is not suitable for older, IT-type power distribution systems found in some European countries.

This system (IT-type) is widely used isolated from earth, in some installations in France,

with impedance to earth, at 230/400V, and in Norway, with voltage limiter, neutral not distributed, at 230V line -to-line.

Contact qualified personnel if you’re uncertain of the type of power system available where you’re installing the display.

・You must connect the USB cable that came with the display to a computer that has a USB compliant interface

and that bears the USB logo.

In addition, the USB source computer must be compliant with IEC 60950-1 and/or IEC 62368-1.

The source computer must be CE marked and carry safety certification marks for Canada and USA.

This is for operating safety and to avoid damage to the display.

・Read Instructions - All the safety and operating instructions should be read before the appliance is operated.

・Retain Instructions - The safety and operating instructions should be retained for future reference.

・Heed Warnings - All warnings on the product and in the operating instructions sh ould be adhered to.

・Follow Instructions - All operating and use instructions should be followed.

・Cleaning - Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners.

Use a damp cloth for cleaning.

・Attachments - Do not use attachments not recommended by the product manufacturer as they may cause hazards.

・Water and Moisture -Do not use this product near water - for example, near a bath tub, wash bowl, kitchen sink,

or laundry tub, in a wet basement, or near a swimming pool, and the like.

・Placement - Do not place this product on an unstable cart, stand, tripod, bracket, or table.

The product may fall, causing serious injury to a child or adult, and serious damage to the product.

Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer,

or sold with the product. Any mounting of the product should follow the manufacturer’s instructions,

and should use a mounting accessory recommended by the manufacturer.

・Ventilation - Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation

of the product and to protect it from overheating, and these openings must not be blocked or covered.

The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface.

This product should not be placed in a built-in installation such as a bookcase or rack unless proper

ventilation is provided or the manufacturer’s instructio ns have been adhered to.

・Lightning - For added protection for this product during a lightning storm, or when it is left unattended and

unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable

system. This will prevent damage to the product due to lightning and power -line surges.

・Overloading -Do not overload wall outlets, extension cords, or integral convenience receptacles

as this can result in a risk of fire or electric shock.

SAFETY INSTRUCTIONS

5

・A product and cart combination should be moved with care.

Quick stops, excessive force, and uneven surfaces may cause

the product and cart combination to overturn.

・Servicing - Do not attempt to service this product yourself as opening or removing covers may expose you

to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

・Safety Check - Upon completion of any service or repairs to this product, ask the service technician

to perform safety checks to determine that The product is in proper operating condition.

・Heat - The product should be situated away from heat sources such as radiators, heat registers, stoves,

or other products (including amplifiers) that produce heat.

IMPORTANT

The following are the normal operating requirements for the display (not including OPS):

MODEL Power requirements

EL55R2 AC100V～240V 300W max

EL65R2 AC100V～240V 300W max

EL75R2 AC100V～240V 330W max

EL86R2 AC100V～240V 450W max

For additional requirements and other information, refer to the display’s specifications.

Federal Communication Commission interference statement

FCC

Suppliers Declaration of Conformity

47 CFR § 2.1077 Compliance Information

Unique Identifier: EL55R2, EL65R2, EL75R2, EL86R2

Responsible Party – U.S. Contact Information

ELMO USA CORP.

6851 Jericho Turnpike, Suite 145

Syosset, NY 11791

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received, including interference that may cause undesired operation.

NOTE

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the

FCC Rules.These limits are designed to provide reasonable protection against harmful interference when the equipment is

operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be

required to correct the interference at his own expense.

CAUTION

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s

authority to operate this equipment.

Restriction

Operations in the 5.15-5.25GHz band are restricted to indoor usage only.

IEEE 802.11b or 802.11g operation of this product in the USA is firmware limited to channels 1 through 13.

CAUTION

i. the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference

to co-channel mobile satellite systems;

ii. the maximum antenna gain permitted for devices in the bands 5250 -5350 MHz and 5470-5725 MHz shall comply with the

e.i.r.p. limit; and

iii. the maximum antenna gain permitted for devices in the band 5725 -5825 MHz shall comply with the e.i.r.p. limits

specified for point-to-point and non point-to-point operation as appropriate.

iv. Users should also be advised that high-power radars are allocated as primary users (i.e., priority users) of the bands

5250-5350 MHz and 5650-5850 MHz and that these radars could cause interference and/or damage to LE -LAN devices.

Radiation exposure statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.

This equipment should be installed and operated with minimum distance of 20 cm between the antenna of this device and

all nearby persons.

This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.

EU declaration of conformity

Hereby TECHNO HORIZON CO., LTD. declares that the radio equipment type Interactive displays model EL55R 2, EL65R2,

EL75R2, EL86R2 are in compliance with directive 2014/53/EU.

WARNING

Operation of this equipment in a residential environment this equipment may could cause radio interference.

The frequency band and the maximum transmitted power in EU are listed below:

Transmitting Band (MHz) 2402-2483.5 5150-5350 5470-5725

Maximum Transmit Power EIRP (dBm) 19 23 23

6

Restrictions in

AT/BE/BG/CZ/DK/EE/FR/DE/IS/IE/IT/EL/ES/CY/LV/LI/LT/LU/HU/MTNL/NO/PL/PT/RO/SI/SK /TR/FI/SE/CH/UK/HR—5150M

Hz-5350MHZ is for indoor use only

CAUTION: EXPOSURE TO RADIO FREQUENCY RADIATION

This equipment complies with EU radiation exposure limits set forth for an uncontrolled environment.

This equipment should be installed and operated with minimum distance 20 cm between the radiator and your body.

The lightning flash with arrowhead symbol, within an equilateral

triangle, is intended to alert the user to the presence of uninsulated

“dangerous voltage” within the product’s enclosure that may be of

sufficient magnitude to constitute a risk of electric shock to

persons.

The exclamation point within an equilateral triangle is intended to

alert the user to the presence of important operating and

maintenance (servicing) instructions in the lit erature

accompanying the product.

This symbol [crossed-out wheeled bin WEEE Annex IV] indicates separate collection of waste electrical and

electronic equipment in the EU countries. Please do not throw the equipment into the domestic refuse.

Please use the return and collection systems available in your country for the disposal of this product.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.

The connection of a non-shielded equipment interface cable to this equipment will invalidate the FCC Certification or

Declaration of this device and may cause interference levels which exceed the limits established by the FCC for this

equipment. It is the responsibility of the user to obtain and use a s hielded equipment interface cable with this device. If this

equipment has more than one interface connector, do not leave cables connected to unused interfaces.

Changes or modifications not expressly approved by the manufacturer could void the user’s autho rity to operate the

equipment.

USER-INSTALLER

CAUTION:

Your authority to operate this FCC verified equipment could be voided if you make changes or modifications not expressly

approved by the party responsible for compliance to Part 15 of the FCC rules.

・Be sure to use the cable supplied with the product.

・The supplied power cord are designed for exclusive use with this product.

Do not use them with other products.

・Do not strongly press the touchscreen or press it with sharp objects.

This may result in damage or malfunction to the touchscreen.

・Be sure to use the power cord applicable to your local power specifications. It may be discolored, deformed, or damaged.

・Do not place this product in any humid, dusty, salt bearing wind, or vibrating locations.

Use it under the following environmental conditions:

Temperature：0℃～ 40℃

Humidity：30％～ 85％(No condensation)

・Use a soft, dry cloth for cleaning. Do not use any volatile solvent such as thinner or benzene.

・If this product is used for longer than the warranty period, its performance and quality may deteriorate due

to the lifetime of its parts. For parts replacement (on chargeable basis), consult the dealer from whom you

purchased this product or our branch/office near your location.

・Copyright

Unless used for personal use, it is prohibited strictly under copyright law to use any photo files

without the prior consent of the copyright holder.

・It is prohibited under copyright law to use or copy any part or the whole of this document without our prior written consent.

・ELMO shall not be liable for any claim for damage or loss of earnings or any claim raised

by a third person due to the use, malfunction or repair of this product.

is registered trademarks of TECHONO HORIZON CO., LTD.

All other company/product names described in this manual are trademarks or registered trademarks of their respective

companies.

BEFORE YOU USE

7

1 Before Use

1.1 Package Contents

The items below are included with this product. If any item is missing, contact the dealer from

whom you purchased this product.

Display monitor

Remote control

Touch pen x2

Power cord x3 (3m)

(TypeA/TypeC/TypeBF)

USB cable

󲤝TypeB-TypeA (3m)

HDMI cable (3m)

Quick Start Guide

Important Safeguards

Eraser

8

1.2 Part Names and Functions

1 Front

Operating panel

No.

Mark

Name

Function

1

IR receiver

IR receiver for the remote control.

Power LED

To indicate the power status. On: Green Off: Red

2

Power

Long press: To turn on or off the power.

Short press: To enter or cancel the standby mode.

3

Home

To display the Home screen.󲼅󲧼P. 20󲼆

4

Return

To go back to the previous screen.

5

Input select

To display the Source Settings screen.󲼅󲧼P. 67󲼆

6

Freeze

To pause the input video (HDMI / Display Port / USB

Type-C / VGA). Press this button again to restart.

7

Screenshot

To capture the currently displayed screen and save it.

The captured image will be saved in the CameraRoll

folder.

8

Volume down

To decrease the volume.

9

Volume up

To increase the volume.

Front I/O ports

No.

Name

Function

10

Type-C

󲼅USB Type-C󲼆

To connect to a USB Type-C device to input video and audio into the

product. It is possible to charge some devices.

When connected to a computer, you can control the computer from the

product by touching the screen of the display monitor.

11

HDMI in

󲼅HDMI Type-A󲼆

To connect the supplied HDMI cable to input video and audio into the

product.

12

TOUCH-USB

󲼅USB Type-B󲼆

To connect the supplied USB cable to control the computer from the

product by touching the screen of the display monitor.

13

USB3.0

󲼅USB Type-A󲼆

To connect a device (such as a USB flash drive, USB mouse, USB

keyboard, or USB camera) that supports USB3.0 and USB2.0.

Front I/O ports

Operating panel

10

11

12

13

1

2

3

4

5

6

7

8

9

2 Side and Bottom

Side I/O ports

No.

Name

Function

1

LAN󲼅RJ-45󲼆

To connect to the network using a LAN cable.

2

HDMI in

󲼅HDMI Type-A󲼆

To connect the supplied HDMI cable to input video and audio into the

product.

3

TOUCH-USB

󲼅USB Type-B󲼆

To connect the supplied USB cable to perform touch operation for the

connected computer on the display monitor of the product.

4

USB2.0

󲼅Type-A󲼆

To connect a USB device (such as a USB flash drive, USB mouse, USB

keyboard, or USB camera) that supports USB2.0.

5

Display Port in

To input video and audio into the product.

6

USB3.0

󲼅USB Type-A󲼆

To connect a device (such as a USB flash drive, USB mouse, USB

keyboard, or USB camera) that supports USB3.0 and USB2.0.

Bottom I/O ports

No.

Name

Function

7

RS-232C

To control the product from a computer via RS-232C.

8

VGA in

To connect a video source device using a VGA cable to input video into

the product.

9

AUDIO in

To connect an audio source device to input audio into the product.

󲼸󲟦3.5mm jack (monaural)󲼺

10

SPDIF out

To connect an optical digital cable to output audio of the product.

11

AUDIO out

To connect an audio output device such as a headphone or active

speaker to output audio of the product. 󲼸󲟦3.5mm jack (monaural)󲼺

12

MIC in

To connect an external microphone to input audio into the product.

󲼸󲟦3.5mm jack (monaural)󲼺

13

HDMI out

To connect the supplied HDMI cable to output video and audio of the

product.

※ KL55R2󲼅HOL󲼆,KL65R2(HOL),KL75(HOL),KL86(HOL) is a model without HDMI-out.

13

OPS slot

connection

position

Side I/O ports

Bottom I/O ports

Handle

Power supply

socket

Main power switch

EL55R2󲺊EL65R2󲼗Located to the

side of the power supply socket

EL75R2

󲺊EL86R2󲼗Located in the

bottom

Handle

AC-IN

12

11

10

9

8

7

1

2

3

4

5

2

6

10

3 Touch pen and Eraser

You can perform touch operations using the supplied Touch pen.

With ELMO Note, it is possible to make different settings for the thick pen nib and the thin pen

nib and draw different lines. Drawn lines can be deleted with the Eraser. 󲼅󲧼P. 28󲼆

The Touch pen and the Eraser are equipped with magnets and can be attached to the

attachment surface under the display monitor.

⚫ If you place your finger near the nib of the Touch pen, it may malfunction.

⚫ If you use the thick pen nib away from the touchscreen, it may be recognized

as a thin pen nib.

⚫ Do not press the pen nib anywhere other than the screen. It may not work

properly.

⚫ When using multiple Touch pens, touch positions and pen information may be

swapped, and line breaks may occur.

⚫ If the pen nib becomes worn or damaged, replace the Touch pen.

For purchasing a Touch pen, contact the dealer where you purchased the

product.

⚫ Do not attach anything other than the supplied Touch pen to the attachment

surface.

⚫ There are two attachment surfaces for EL65R2, EL75R2, and EL86R2, and

one for EL55R2. Not all included Touch pens or Erasers can be attached.

⚫ The supplied Touch pen has a built-in magnet. Keep the pen away from

watches and magnetic cards.

Note

Thick pen nib

Thin pen nib

Touch pen

Eraser

11

4 Remote Control

No.

Name

Function

1

Power button

Long press: To turn on or off the power.

Short press: To enter or cancel the standby mode.

2

Enter button

To decide the selection in a dialog box.

3

Home button

To display the Home screen.󲼅󲧼P. 20󲼆

4

Freeze button

To pause the input video (HDMI / Display Port / USB Type -C /

VGA). Press this button again to restart.

5

OPS button

To display the screen of the PC unit (Windows).

󲤝Optional

6

Input select button

To display the Source Settings screen.󲼅󲧼P. 67󲼆

7

Direction buttons

To move the selection item up, down, left, and right.

8

Return button

To go back to the previous screen.

9

Whiteboard button

To start the whiteboard app (ELMO Note).󲼅󲧼P. 25󲼆

10

Screenshot button

To capture the currently displayed screen and save it.

11

Volume down button

To decrease the volume.

12

Volume up button

To increase the volume.

13

Mute button

To mute the audio output.

Press this button again to release the mute.

Save destination of the image captured by the Screenshot button:

Local > CameraRoll

Note

1

2

3

4

5

11

6

7

8

9

10

12

13

12

◆ Preparation

◼ Inserting batteries

1. Slide and open the cover in the back of the remote control.

2. Insert 2pcs of AAA batteries.

Pay attention to the polarity, which is printed inside the remote control.

3. Firmly close the cover.

⚫ Use manganese AAA batteries for the batteries.

⚫ When battery power becomes low, replace them with new batteries as soon as

possible.

⚫ If you do not use the remote control for a long time, remove the batteries from the

remote control.

◼ Operable Range of the Remote Control

If there is no obstruction between the IR receiver of the display monitor and the remote control,

the operable range of the remote control is as follows:

Distance: within 5m

Angle: within 30° up, down, left, and right

Note

5m

30 degrees

13

1.3 Installation

1 Installation Conditions

󲺊Use the product in the following conditions.

Temperature

0󲽛40󲥞

Humidity

20󲽛80󲼃

󲺊To prevent internal heat buildup, install the display monitor in a well-ventilated place, keeping the

distance as specified in the following figure from the surrounding area.

Use the following screws to attach the VESA brackets.

For EL65R2󲺊EL75R2󲺊EL86R2: M8 screws with a length of 20 mm

For EL55R2: M6 screws with a length of 20 mm

Caution

⚫ Since the display monitor is heavy, consult the dealer from whom you purchased

this product when installing, removing or moving it.

⚫ Installation must be done by professional service engineers. Otherwise, injury may

occur by improper installation.

⚫ If you want to mount the display monitor on a wall or suspend it from the ceiling,

ask a specialist for installation work.

ELMO is not responsible for any accident or damage caused by improper installation.

⚫ If you need to move the display monitor after it is attached to the stand, always

move the product with 2 or more people.

⚫ Be careful not to block the ventilation holes when installing. The heat will be

trapped inside and may cause a malfunction or a fire.

⚫ Do not install the display monitor in a place where it may be exposed to rain or

spray, or in a place with high humidity.

⚫ Do not install the display monitor near the air outlet of the air conditioner.

Condensation may form due to sudden temperature changes, which may corrode the inside

and cause a malfunction.

30cm

Wall

30cm

10cm

14

◆ Attachment of the Display Monitor to the Stand

You can attach the display monitor to the stand.

The positions of the screw holes are as shown in the following figure.

For the assembly of the stand, refer to the instruction manual of the stand.

55 inch󲼗VESA 400x400

65 inch

󲼗

VESA 600x400

75 inch

󲼗

VESA 800x400

86 inch

󲼗

VESA 800x600

15

1.4 Turning On or Off the Power

1 Connecting the Power Cord

Connect the supplied power cord to the power supply socket on the side and plug the power

plug into an outlet.

Caution

⚫ Always use the supplied power cord.

⚫ Use the power cord usable in your country.

2 Turning On the Power

1 Press “-“ on the Main power switch on the bottom.

Location of the Main power switch:

For EL55R2 and EL65R2: Side

For EL75R2 and EL86R2: Bottom

2 Long-press the Power button on the front.

The power can also be turned on by long-pressing the Power button on the remote

control.

Supplied power cord

AC-IN

Main power switch

Main power

ON

Main power

OFF

EL55R2󲺊EL65R2

EL75R2󲺊EL86R2

16

◆ Initial Startup

At initial startup, the Settings screen will appear in the order of "Language setting", "Date and

time setting", and "Network setting".

Settings after "Language setting" can be skipped by tapping "Skip and start immediately" or

“Next".

1 Language setting

2 Date and Time setting

To skip all subsequent steps and

complete the settings

To go to the next page

To go back to the

previous screen

Tap the language

The date and time are automatically set

according to the time zone.

ON: To display the time in 24-hour format

OFF: To display the time in 12-hour format

To set the time zone

To configure the date and time setting

manually when “Automatically update date and

time” setting is OFF

17

3 Network setting

⚫ For the Network setting, set either Wireless network or Ethernet.

⚫ If you want to set the proxy in the Wireless network settings, or if yo u want to

connect to a stealth access point, set them after displaying the Home screen.

It is not possible to set them from the initial startup screen. 󲼅󲧼P. 70󲼆

⚫ Language setting, Date and time setting, and Network setting can be reset.

4 Home screen

The Home screen will appear after completing all the settings.

3 Turning Off the Power

1 Long-press the Power button on the front

The power can also be turned off by long-pressing the Power button on the remote

control.

Note

To configure the wireless network (wireless

LAN) settings

To configure the wired network settings

18

2 Select “Sure” in the Shutdown confirmation dialog.

Select “Cancel” if you want to cancel the shutdown.

3 Press 󲣿󲶾󲣿 on the Main power switch on the bottom.

⚫ If there is no operation after the Shutdown confirmation dialog is displayed

and the countdown timer reaches zero, the product will automatically shut

down.

⚫ Do not press 󲣿󲶾󲣿 on the Main power switch on the back before shutting

down the product. By doing so may cause a malfunction.

⚫ If you do not use the product, shut it down.

⚫ If the product freezes or is unstable, try shutting it down.

4 Standby Mode

Press the Power button on the front while the product is turned on to enter the Standby mode.

To cancel the Standby mode, press the Power button again.

⚫ The Power LED turns green in the Standby mode.

⚫ The Power LED turns red when the product is shutdown.

Note

19

2 Basic Operations

2.1 Touch Operations

You can perform touch operations with your finger or the supplied Touch pen.

For details on Windows touch operations, refer to Windows Help.

Name

Function

Finger movements

Single tap

󲼅Tap󲼆

Touch once briefly.

⚫ Works as the left click of a

mouse.

Double tap

Touch same place twice

quickly.

⚫ Works as the double click

of a mouse.

Long-press

Touch and hold.

⚫ Works as the right click of

a mouse.

Drag and drop

Touch and hold the icon or slide

and move it. Then release the

finger at the specified position.

⚫ Works as the drag and

drop of a mouse.

Swipe / Flick

Swipe: Move the finger while

touching the screen.

Flick: Touch the screen and

brush the finger quickly across

the screen.

2-finger press

Touch and hold with two

fingers.

The distance between two

points should be 2-5 cm.

Zoom in

󲼅Enlarge󲼆

Touch two points at the same

time and move fingers away

from each other.

⚫ To be used in the screen

where zooming operation

is possible.

Zoom out

󲼅Shrink󲼆

Touch two points at the same

time and move fingers closer to

each other.

⚫ To be used in the screen

where zooming operation

is possible.

20

2.2 Basic Screen Operations

◆ Home Screen

The Home screen will appear when the power is turned on.

Tap the List of apps icon at the bottom right of the screen to display a list apps installed on the

product.

Main Apps

Icon

Name

Function

ELMO Note

To start ELMO Note (whiteboard). 󲼅󲧼P. 25󲼆

Camera Roll

To start Camera Roll. 󲼅󲧼P. 38󲼆

ELMO Camera

To start a USB camera. 󲼅󲧼P. 40󲼆

E-Browser

To start E Browser. 󲼅󲧼P. 42󲼆

File Manager

To start File Manager. 󲼅󲧼P. 56󲼆

Timer

To start ELMO timer. 󲼅󲧼P. 45󲼆

Screen Mirror

󲼅Transcreen󲼆

To share the screen of other device such as a tablet.

󲼅󲧼P. 51󲼆

Avira Security

To perform a virus scan or cleanup of internal memory.

󲼅󲧼P. 54󲼆

ELMO Play

To start ELMO Play. 󲼅󲧼P. 55󲼆

Menu

To configure the Source Settings. 󲼅󲧼P. 67󲼆

Settings

To configure the settings of the product. 󲼅󲧼P. 70󲼆

Advanced Setting

To set the proxy settings or connection settings to the stealth

access point when connecting to the wireless network.

󲼅󲧼P. 71󲼆

WPS Office

To create/view/edit/save Office documents or browse PDF

files.

Cloud

To start Cloud.

You can select between “Google Drive” and “One Drive”.

Page is loading ...

Elmo EL86R2-KIT Owner's manual

This manual is also suitable for

Elmo EL86R2-KIT Owner's manual

Related papers

Other documents