AOC CU34P2C User manual

Category
TVs & monitors
Type
User manual
1
CU34P2C
www.aoc.com
2022 AOC.All Rights Reserved©
LCD Monitor
User Manual
i
Safety ................................................................................................................................................................................... 1
National Conventions ................................................................................................................................................ 1
Power ........................................................................................................................................................................ 2
Installation ................................................................................................................................................................. 3
Cleaning .................................................................................................................................................................... 4
Other ......................................................................................................................................................................... 5
Setup .................................................................................................................................................................................... 6
Contents in Box ......................................................................................................................................................... 6
Setup Base ................................................................................................................................................................ 7
Adjusting Viewing Angle ............................................................................................................................................ 8
Connecting the Monitor ............................................................................................................................................. 9
Wall Mounting.......................................................................................................................................................... 10
Adaptive sync function .............................................................................................................................................11
Adjusting ............................................................................................................................................................................. 12
Hotkeys ................................................................................................................................................................... 12
OSD Setting ............................................................................................................................................................ 13
Luminance ................................................................................................................................................... 14
Color Setup .................................................................................................................................................. 15
Picture Boost ............................................................................................................................................... 16
OSD Setup ................................................................................................................................................... 17
PIP Setting ................................................................................................................................................... 18
Game Setting ............................................................................................................................................... 19
Extra ............................................................................................................................................................ 20
Exit ............................................................................................................................................................... 21
LED Indicator .......................................................................................................................................................... 22
Troubleshoot ....................................................................................................................................................................... 23
Specication ....................................................................................................................................................................... 24
General Specication .............................................................................................................................................. 24
Preset Display Modes ............................................................................................................................................. 25
Pin Assignments ...................................................................................................................................................... 26
Plug and Play .......................................................................................................................................................... 27
1
Safety
National Conventions
The following subsections describe notational conventions used in this document.
Notes, Cautions, and Warnings
Throughout this guide, blocks of text may be accompanied by an icon and printed in bold type or in italic type. These
blocks are notes, cautions, and warnings, and they are used as follows:
NOTE: A NOTE indicates important information that helps you make better use of your computer system.
CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the
problem.
WARNING: A WARNING indicates the potential for bodily harm and tells you how to avoid the problem. Some warnings
may appear in alternate formats and may be unaccompanied by an icon. In such cases, the specic presentation of the
warning is mandated by regulatory authority.
2
Power
The monitor should be operated only from the type of power source indicated on the label. If you are not sure of the
type of power supplied to your home, consult your dealer or local power company.
The monitor is equipped with a three-pronged grounded plug, a plug with a third (grounding) pin. This plug will t
only into a grounded power outlet as a safety feature. If your outlet does not accommodate the three-wire plug, have an
electrician install the correct outlet, or use an adapter to ground the appliance safely. Do not defeat the safety purpose of
the grounded plug.
Unplug the unit during a lightning storm or when it will not be used for long periods of time. This will protect the
monitor from damage due to power surges.
Do not overload power strips and extension cords. Overloading can result in re or electric shock.
To ensure satisfactory operation, use the monitor only with UL listed computers which have appropriate congured
receptacles marked between 100-240V AC, Min. 5A.
The wall socket shall be installed near the equipment and shall be easily accessible.
3
Installation
Do not place the monitor on an unstable cart, stand, tripod, bracket, or table. If the monitor falls, it can injure a
person and cause serious damage to this product. Use only a cart, stand, tripod, bracket, or table recommended by
the manufacturer or sold with this product. Follow the manufacturers instructions when installing the product and use
mounting accessories recommended by the manufacturer. A product and cart combination should be moved with care.
Never push any object into the slot on the monitor cabinet. It could damage circuit parts causing a re or electric
shock. Never spill liquids on the monitor.
Do not place the front of the product on the oor.
If you mount the monitor on a wall or shelf, use a mounting kit approved by the manufacturer and follow the kit
instructions.
Leave some space around the monitor as shown below. Otherwise, air-circulation may be inadequate hence
overheating may cause a re or damage to the monitor.
To avoid potential damage, for example the panel peeling from the bezel, ensure that the monitor does not tilt
downward by more than -5 degrees. If the -5 degree downward tilt angle maximum is exceeded, the monitor damage will
not be covered under warranty.
See below the recommended ventilation areas around the monitor when the monitor is installed on the wall or on the
stand:
Installed with stand
Installed with stand
12 inches
30cm
4 inches
10cm
4 inches
10cm
4 inches
10cm
Leave at lease this
space around the set
Please purchase a suitable wall mount to avoid the lack of distance between the back signal cable and the wall.
4
Cleaning
Clean the cabinet regularly with cloth.You can use soft-detergent to wipe out the stain, instead of strong-detergent
which will cauterize the product cabinet.
When cleaning, make sure no detergent is leaked into the product. The cleaning cloth should not be too rough as it
will scratch the screen surface.
Please disconnect the power cord before cleaning the product.
5
Other
If the product is emitting a strange smell, sound or smoke, disconnect the power plug IMMEDIATELY and contact a
Service Center.
Make sure that the ventilating openings are not blocked by a table or curtain.
Do not engage the LCD monitor in severe vibration or high impact conditions during operation.
Do not knock or drop the monitor during operation or transportation.
6
Setup
Contents in Box
*
*
*
*
*
Quick Start Warranty card Stand Base
Power Cable USB Cable HDMI Cable DP Cable
Not all signal cables (HDMI/DP/USB/Audio cables) will be provided for all countries and regions. Please check with
the local dealer or AOC branch oce for conrmation.
7
Setup Base
Please setup or remove the base following the steps as below.
Please place the monitor on a soft and at surface to prevent the scratch.
Setup:
4
Remove:
1
4
2
3
8
Adjusting Viewing Angle
For optimal viewing it is recommended to look at the full face of the monitor, then adjust the monitor’s angle to your own
preference.
Hold the stand so you will not topple the monitor when you change the monitors angle.
You are able to adjust the monitor as below:
150 ± 5mm
-5.5° ±1° 22° ±1.5°
NOTE:
Do not touch the LCD screen when you change the angle. It may cause damage or break the LCD screen.
Warning
To avoid potential screen damage, such as panel peeling, ensure that the monitor does no t tilt downward by more
than -5 degrees.
Do not press the screen while adjusting the angle of the monitor. Grasp only the bezel.
9
Connecting the Monitor
Cable Connections In Back of Monitor and Computer:
HDMI USB C
~
123
4
56
7
8
9
1. Power
2. HDMI
3. DisplayPort
4. USB-C
5. USB-PC upstream
6. USB 3.2 Gen 1
7. USB3. 2 Gen1+Quick Charging
8. Earphone out
9. USB 3.2 Gen 1
Connect to PC
1. Connect the power cord to the back of the display rmly.
2. Turn o your computer and unplug its power cable.
3. Connect the display signal cable to the video connector on the back of your computer.
4. Plug the power cord of your computer and your display into a nearby outlet.
5. Turn on your computer and display.
If your monitor displays an image, installation is complete. If it does not display an image, please refer Troubleshooting.
To protect equipment, always turn o the PC and LCD monitor before connecting.
10
Wall Mounting
Preparing to Install An Optional Wall Mounting Arm.
4
HDMI USB C
~
This monitor can be attached to a wall mounting arm you purchase separately. Disconnect power before this procedure.
Follow these steps:
1. Remove the base.
2. Follow the manufacturers instructions to assemble the wall mounting arm.
3. Place the wall mounting arm onto the back of the monitor. Line up the holes of the arm with the holes in the back of the
monitor.
4. Insert the 4 screws into the holes and tighten.
5. Reconnect the cables. Refer to the users manual that came with the optional wall mounting arm for instructions on
attaching it to the wall.
Noted: VESA mounting screw holes are not available for all models, please check with the dealer or ocial department
of AOC.
-5°
0° 90°
* Display design may dier from those illustrated.
WARNING:
1. To avoid potential screen damage, such as panel peeling, ensure that the monitor does not tilt downward by more than
-5 degrees.
2. Do not press the screen while adjusting the angle of the monitor. Grasp only the bezel.
11
Adaptive sync function
1. Adaptive sync function is working with DP/H1MI
2. Compatible Graphics Card: Recommend list is as the below, also could be checked by visiting www.AMD.com
AMD Radeon™ RX 480
AMD Radeon™ RX 470
AMD Radeon™ RX 460
Radeon Pro Duo
AMD Radeon R9 300 Series
AMD Radeon R9 Fury X
AMD Radeon R9 360
AMD Radeon R7 360
AMD Radeon R9 295X2
AMD Radeon R9 290X
AMD Radeon R9 290
AMD Radeon R9 285
AMD Radeon R7 260X
AMD Radeon R7 260
12
Adjusting
Hotkeys
1 2 3 4 5
1 Source/Auto/Exit
2 Clear Vision/<
3 Volume/>
4 Menu/Enter
5 Power
Power
Press the Power button to turn on the monitor.
Menu/Enter
When there is no OSD, Press to display the OSD or conrm the selection. Press about 2 second to turn o the monitor.
Volume/>
Press Volume button to active volume adjustment bar.
Source/Auto/Exit
When the OSD is closed, press Source/Auto/Exit button will be Source hot key function.
When the OSD is closed, press Source/Auto/Exit button continuously about 2 second to do auto congure (Only for the
models with D-Sub).
13
Clear Vision
1. When there is no OSD, Press the “<” button to activate Clear Vision.
2. Use the “<” or “>” buttons to select between weak, medium, strong, or o settings. Default setting is always “o”.
3. Press and hold “<” button for 5 seconds to activate the Clear Vision Demo, and a message of “Clear Vision Demo: on”
will be display on the screen for a duration of 5 seconds. Press Menu or Exit button, the message will disappear. Press
and hold “<” button for 5 seconds again, Clear Vision Demo will be o.
Clear Vision function provides the best image viewing experience by converting low resolution and blurry images into
clear and vivid images.
Clear Vision
O
Adjust the Clear Vision
Weak
Medium
Strong
Clear Vision Demo On or O Disable or Enable Demo
14
OSD Setting
Basic and simple instruction on the control keys.
Luminance Color Setup Picture Boost OSD Setup ExitExtra
Contrast 50
Brightness 90
Eco mode Standard
Gamma Gamma1
DCR Off
HDR Mode Off
PIP Setting
PIP
Game Setting
1. Press the MENU-button to activate the OSD window.
2. Press Left or Right to navigate through the functions. Once the desired function is highlighted, press the
MENU-button to activate it, press Left or Right to navigate through the sub-menu functions. Once the desired
function is highlighted, press MENU-button to activate it.
3. Press Left or to change the settings of the selected function. Press to exit. If you want to adjust any other
function, repeat steps 2-3.
4. OSD Lock Function: To lock the OSD, press and hold the MENU-button while the monitor is o and then press
power button to turn the monitor on. To un-lock the OSD - press and hold the MENU-button while the monitor
is o and then press power button to turn the monitor on.
Notes:
1. If the product has only one signal input, the item of “Input Select” is disable to adjust.
2. If the product screen size is 4:3 or input signal resolution is native resolution, the item of “Image Ratio” is disabled.
3. One of DCR, Color Boost and Picture Boost functions is activated, the other two function s are turned o accordingly.
15
Luminance
Luminance Color Setup Picture Boost OSD Setup ExitExtra
Contrast 50
Brightness 90
Eco mode Standard
Gamma Gamma1
DCR Off
HDR Mode Off
PIP Setting
PIP
Game Setting
Contrast 0-100 Contrast from Digital-register
Brightness 0-100 Backlight Adjustment
Eco mode
Standard Standard Mode
Text Text Mode
Internet Internet Mode
Game Game Mode
Movie Movie Mode
Sports Sports Mode
Reading Reading Mode
Uniformity Uniformity Mode
Gamma
Gamma1 Adjust to Gamma 1
Gamma2 Adjust to Gamma 2
Gamma3 Adjust to Gamma 3
DCR
O Disable dynamic contrast ratio
On Enable dynamic contrast ratio
HDR Mode
O
Adjust HDR Mode
HDR Picture
HDR Movie
HDR Game
16
Color Setup
Luminance
Red 50
Green 50
Blue 50DCB Demo Off
Color Temp. Warm
DCB Mode Off
Color Setup
Picture Boost OSD Setup ExitExtraPIP Setting
PIP
Game Setting
LowBlue Mode Off
Color Temp.
Warm Recall Warm Color Temperature from EEPROM
Normal Recall Normal Color Temperature from EEPROM
Cool Recall Cool Color Temperature from EEPROM
sRGB Recall SRGB Color Temperature from EEPROM
User Restore Color Temperature from EEPROM
DCB Mode
Full Enhance On / O Disable or Enable Full Enhance Mode
Nature Skin On / O Disable or Enable Nature Skin Mode
Green Field On / O Disable or Enable Green Field Mode
Sky-blue On / O Disable or Enable Sky-blue Mode
AutoDetect On / O Disable or Enable AutoDetect Mode
O Disable DCB Mode
DCB Demo On / O Disable or Enable Demo
Red 0-100 Red gain from Digital-register
Green 0-100 Green gain from Digital-register
Blue 0-100 Blue gain from Digital-register
17
Picture Boost
Luminance
Brightness 50
Contrast 50
H. Position 0
V. Position 0
Bright Frame Off
Frame Size 14
Picture Boost Color Setup
OSD Setup ExitExtraPIP Setting
PIP
Game Setting
Bright Frame On / O Disable or Enable Bright Frame
Frame Size 14-100 Adjust Frame Size
Brightness 0-100 Adjust Frame Brightness
Contrast 0-100 Adjust Frame Contrast
H. position 0-100 Adjust Frame horizontal Position
V. position 0-100 Adjust Frame vertical Position
Note:
Adjust the brightness, contrast, and position of the Bright Frame for better viewing experience.
18
OSD Setup
ExitExtra
Luminance Color Setup
H. Position 50
V. Position 0
Transparence 25
Language English
Timeout 10 Break Reminder Off
OSD Setup Picture Boost
DP Capability 1.1 USB
PIP Setting
PIP
Game Setting
2.0 USB Selection Auto
Language Select the OSD language
Timeout 5-120 Adjust the OSD Timeout
DP Capability 1.1 / 1.2
If the DP video content supports DP 1.2, please
seclect DP1.2 for DP Capability , otherwise,
please select DP1.1.
Please be noted that only DP1.2 support Adaptive-
Sync function
H. Position 0-100 Adjust the horizontal position of OSD
V. Position 0-100 Adjust the vertical position of OSD
USB* 3.2Gen1 / 2.0 / O For model need to turn on/o USB power during
power saving.
Transparence 0-100 Adjust the transparence of OSD
Break
Reminder On / OBreak reminder if the user continuously work for
more than 1hrs
USB Selection Auto / USB C / USB up
*AUTO: Switch with display input source
*USB C/USB up: Fix up stream not change with
input source.
Notes:
*USB C(DP Alt) signal input, and “USB” is set to “2.0”, the maximum resolution is 3440x1440@100Hz.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30

AOC CU34P2C User manual

Category
TVs & monitors
Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI