STODDART Culinaire CH.IBGJ.BMC.U.GSB User manual

Type
User manual

This manual is also suitable for

A guide on the use, care and maintenance
of your quality Culinaire product
BAIN MARIE COUNTER LINE
UNDER BENCH / DROP-IN
Models:
CH.BMC.D.GSB / CH.BMC.D.GSF / CH.BMC.U.GSB / CH.BMC.U.GSF / CH.IBGJ.BMC.U.GSB / CH.IBGJ.BMC.U.GSF / CH.IBGS.BMC.U.GSB
CH.IBGS.BMC.U.GSF / CH.IBSJ.BMC.U.GSB / CH.IBSJ.BMC.U.GSF / CH.IBSS.BMC.U.GSB / CH.IBSS.BMC.U.GSF
SPECIFICATION, INSTALLATION
AND OPERATION MANUAL
READ ALL INSTRUCTIONS BEFORE USE
Revision: A - 9/09/2021 - 03
Page Intentionally Left Blank
Page 1
Due to continuous product research and development,
the information contained herein is subject to change without notice.
www.stoddart.com.au
www.stoddart.co.nz
Page 2
Due to continuous product research and development,
the information contained herein is subject to change without notice.
www.stoddart.com.au
www.stoddart.co.nz
Introduction
Your New Culinaire Product � � � � � � � � � � � � � � � � � � 3
Australia and New Zealand Warranty � � � � � � � � � � � � � 4
Warranty Period
Warranty Registration
General Precautions � � � � � � � � � � � � � � � � � � � � � 4
Installation
Product Overview � � � � � � � � � � � � � � � � � � � � � � � 5
Setting Up � � � � � � � � � � � � � � � � � � � � � � � � � � 6
Handling
Unpacking
Positioning
Plumbing Connections � � � � � � � � � � � � � � � � � � � � 7
Information
Electrical Connection � � � � � � � � � � � � � � � � � � � � � 8
Drop-in Bench Top � � � � � � � � � � � � � � � � � � � � � � 9
Cutout Sizes (CH.BMC.D)
Under Counter Bench Tops � � � � � � � � � � � � � � � � � � 9
Bench Tops (CH.BMC.U)
Bain Marie Element Covers & Dividers � � � � � � � � � � � 10
Bain Marie Element Covers
Bain Marie Dividers
Specification
Technical Specifications � � � � � � � � � � � � � � � � � � 11
CH.BMC.D
CH.BMC.U
CH.IBXX.BMC.U.GSF
CH.IBXX.BMC.U.GSF
Operation
Initial Start-up & Operation � � � � � � � � � � � � � � � � � 17
Bain Marie - Using as a Wet Unit
Bain Marie - Using as a Dry Unit
Food Safety � � � � � � � � � � � � � � � � � � � � � � � � � 18
Food Temperature
Loading Bain Marie
After Service � � � � � � � � � � � � � � � � � � � � � � � � 18
Food Storage
Bain Marie
Gastronorm (GN) Pans � � � � � � � � � � � � � � � � � � � 18
Gastronorm Pans
Temperature Adjustment � � � � � � � � � � � � � � � � � � 19
Gantry Operation � � � � � � � � � � � � � � � � � � � � � � 20
Replacing Heat Lamp Bulbs � � � � � � � � � � � � � � � � 20
Cleaning and Maintenance
Cleaning � � � � � � � � � � � � � � � � � � � � � � � � � � 21
Cleaning and Maintenance Schedule
Materials Required
General Information
Corrosion Protection
Surface Finish
Bain Marie (Daily)
Element Protection (Daily)
Descaling the Unit (Monthly)
External Surfaces (Daily)
Glass (Daily)
Troubleshooting � � � � � � � � � � � � � � � � � � � � � � 23
Disposal � � � � � � � � � � � � � � � � � � � � � � � � � � 24
Page 3
Due to continuous product research and development,
the information contained herein is subject to change without notice.
www.stoddart.com.au
www.stoddart.co.nz
Introduction
Thank you for choosing this quality Culinaire product�
All Culinaire products are designed and manufactured to meet the needs of food service professionals� By caring for and maintaining your
new Culinaire product in accordance with these instructions, will provide many years of reliable service�
Stoddart is a wholly Australian owned company, which manufactures and/or distributes a comprehensive range of food service equipment for
kitchens, food preparation and presentation� Stoddart products are manufactured and/or engineered in Australia to provide excellent results
whilst offering value-for-money, ease-of-use and reliability
Carefully read this instruction booklet, as it contains important advice for safe installation, operation and maintenance�
Keep this booklet on hand in a safe place for future reference by other operators or users�
Stoddart design, manufacture & distribute Food Service Equipment (appliances) exclusively for the commercial market.
This appliance is not designed nor intended for household or domestic use and must not be used for this purpose.
This product is intended for commercial use, and in line with Australian electrical safety standards the following warnings are provided:
This product is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of
experience and knowledge, unless they have been given supervision or instruction concerning the use of the product by a person
responsible for their safety Children should be supervised to ensure that they do not play with the product
If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualifi ed persons in order to avoid
a hazard
The manufacturer and distributor cannot be held responsible or liable for any injuries or damages of any kind that occur
to persons, units or others, due to abuse and misuse of this unit in regards to installation, removal, operation, servicing or
maintenance, or lack of conformity with the instructions indicated in this documentation�
Disclaimer
All units made by the manufacturer are delivered assembled, where possible, and ready to install� Any installation, removal,
servicing, maintenance and access or removal of any parts, panels or safety barriers that is not permitted, does not comply
in accordance to this documentation, or not performed by a TRAINED AND AUTHORISED SPECIALIST will result in the
IMMEDIATE LOSS OF THE WARRANTY.
The manufacturer cannot be held responsible or liable for any unauthorised modifi cations or repairs� All modifi cations or
repairs must be approved by the manufacturer in writing before initiating� All modifi cations or repairs performed to this unit
must be performed at all times by a TRAINED AND AUTHORISED SPECIALIST.
Your New Culinaire Product
To register your new product, Follow the below Link/QR code�
www�stoddart�com�au/warranty-information
All Stoddart manufactured and distributed products are covered by Stoddart’s standard Australia and New Zealand Product Warranty (minimum
12 month on-site parts and labour, terms and conditions apply)� Further to this standard warranty, certain products have access to an extended
warranty Full terms, conditions and exclusions can be found using the below Link/QR code�
Warranty & Registration
Page 4
Due to continuous product research and development,
the information contained herein is subject to change without notice.
www.stoddart.com.au
www.stoddart.co.nz
Introduction
Thank you for choosing this quality Culinaire product�
All Culinaire products are designed and manufactured to meet the needs of food service professionals� By caring for and maintaining your
new Culinaire product in accordance with these instructions, will provide many years of reliable service�
Stoddart is a wholly Australian owned company, which manufactures and/or distributes a comprehensive range of food service equipment for
kitchens, food preparation and presentation� Stoddart products are manufactured and/or engineered in Australia to provide excellent results
whilst offering value-for-money, ease-of-use and reliability
Carefully read this instruction booklet, as it contains important advice for safe installation, operation and maintenance�
Keep this booklet on hand in a safe place for future reference by other operators or users�
Stoddart design, manufacture & distribute Food Service Equipment (appliances) exclusively for the commercial market.
This appliance is not designed nor intended for household or domestic use and must not be used for this purpose.
This product is intended for commercial use, and in line with Australian electrical safety standards the following warnings are provided:
This product is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of
experience and knowledge, unless they have been given supervision or instruction concerning the use of the product by a person
responsible for their safety Children should be supervised to ensure that they do not play with the product
If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualifi ed persons in order to avoid
a hazard
The manufacturer and distributor cannot be held responsible or liable for any injuries or damages of any kind that occur
to persons, units or others, due to abuse and misuse of this unit in regards to installation, removal, operation, servicing or
maintenance, or lack of conformity with the instructions indicated in this documentation�
Disclaimer
All units made by the manufacturer are delivered assembled, where possible, and ready to install� Any installation, removal,
servicing, maintenance and access or removal of any parts, panels or safety barriers that is not permitted, does not comply
in accordance to this documentation, or not performed by a TRAINED AND AUTHORISED SPECIALIST will result in the
IMMEDIATE LOSS OF THE WARRANTY.
The manufacturer cannot be held responsible or liable for any unauthorised modifi cations or repairs� All modifi cations or
repairs must be approved by the manufacturer in writing before initiating� All modifi cations or repairs performed to this unit
must be performed at all times by a TRAINED AND AUTHORISED SPECIALIST.
All units MUST be installed according to the procedures stated in the installation section of this manual
In the case of new personnel, training is to be provided before operating the equipment
DO NOT use this unit for any other purpose than its intended use
DO NOT store explosive substances such as aerosol cans with a fl ammable propellant in or near this unit
Keep fi ngers out of “pinch point” areas
Unit is not waterproof DO NOT use jet sprays, hoses or pour water over/on the exterior of the unit
Only use this unit with voltage specifi ed on the rating label
DO NOT remove any cover panels that may be on the unit
DO NOT use sharp objects to activate controls
If any fault is detected, refer to troubleshooting
The manufacturer declines any liability for damages to persons and/or things due to an improper/wrong and/or unreasonable use of the
machine
When using any electrical unit, safety precautions must always be observed�
Our units have been designed for high performance� Therefore, the unit must be used exclusively for the purpose for which it has been designed�
General Precautions
To register your new product, Follow the below Link/QR code�
www�stoddart�com�au/warranty-information
All Stoddart manufactured and distributed products are covered by Stoddart’s standard Australia and New Zealand Product Warranty (minimum
12 month on-site parts and labour, terms and conditions apply)� Further to this standard warranty, certain products have access to an extended
warranty Full terms, conditions and exclusions can be found using the below Link/QR code�
Warranty & Registration
Warranty Registration
Warranty Period
Australia and New Zealand Warranty
Page 5
Due to continuous product research and development,
the information contained herein is subject to change without notice.
www.stoddart.com.au
www.stoddart.co.nz
Control Panel
Bain Marie - Drop-in
CH�BMC�D
Bain Marie - Under Bench
CH�BMC�D
Gantry
Drain Valve
Code Explanation
CH = Culinaire Heated
IBSS = Island Buffet - Stainless Steel Top and Stainless Steel Panels
IBSJ = Island Buffet - Stainless Steel Top and Joinery Panels
IBGS = Island Buffet - Stone Top and Stainless Steel Panels
IBGJ = Island Buffet - Stone Top and Joinery Panels
BMC = Bain Marie Counter Line
D = Drop-in
U = Under Bench
GSF = Flat Glass Gantry
GSB = Flat Glass Gantry - Black Painted Centre Section
3 to 8 = 3 to 8 Module
Installation
Product Overview
CAUTION
Surface is HOT!
Page 6
Due to continuous product research and development,
the information contained herein is subject to change without notice.
www.stoddart.com.au
www.stoddart.co.nz
Installation
Setting Up
Handling
Unpacking
Positioning
Use suitable means to move the unit;
- For smaller items use two people
- For large items a fork lift, pallet trolley or similar (the forks should reach completely beneath the pallet)
Check the unit for damage before and after unpacking� If unit is damaged, contact the distributor and manufacturer
Should any item have physical damage, report the details to the freight company and to the agent responsible for the dispatch within
seven (7) days of receipt� No claims will be accepted or processed after this period
The unit is supplied fully assembled
Remove all protective plastic film, tapes, ties and packers before installing and operating
Clean off any remaining residue from the interior/exterior of the unit using a clean cloth dampened with warm soapy water
Please consult national and local standards to ensure that your unit is positioned in accordance with any existing requirement
WARNING
Improper installation, adjustments, alterations, service or
maintenance can cause property damage, injury or death.
100mm
APPLIANCE
100mm
100mm
Front
Choose an area that is well ventilated and provides access for future maintenance
Place the unit on a level stable work surface capable of supporting its weight
Do not position the unit in:
- Wet areas
- Near heat and/or steam sources
- Near flammable substances
Allow an air gap between the unit and other objects or surfaces� A minimum gap of 100mm from all sides is recommend for normal
operational use (if the unit is near any heat sensitive material we suggest you allow additional space)
Page 7
Due to continuous product research and development,
the information contained herein is subject to change without notice.
www.stoddart.com.au
www.stoddart.co.nz
Plumbing Connections
Information
Installation
The unit is supplied with a G 1½” BSP drainage connection
The wastewater connection screws into the drainage connection� The wastewater MUST be tested for leakages after being installed
The unit MUST be on a level surface for the water to drain properly
The Bain Marie is fitted with an overflow which maintains the correct water level in the well
Before use, the water purity needs be checked; high mineral water can corrode the elements and taint the water/food� If needed, a
filtration system should be installed
The unit is supplied with a G ½” BSP Water Connection for filling the well� The water valve MUST be tested for leakages after being
installed
It is recommended that the Bain Marie is connected to the water mains and drained to a tundish
The unit must be connected to a drain and either a hot or cold water supply (hot produces quicker start up times) with an isolation tap
Waste Connection
Water Connection
Overflow Connection
Electrical Connection
IMPORTANT
This unit must be operated on potable water. If the water has a
high mineral content, pretreatment may be necessary or your
warranty could be voided.
IMPORTANT
This unit must be installed in accordance with AS/NZ 3500.1
Page 8
Due to continuous product research and development,
the information contained herein is subject to change without notice.
www.stoddart.com.au
www.stoddart.co.nz
Installation
Single Phase Units:
Supplied and fi tted with an appropriately rated plug and lead, indicated as:
- 10A plug & lead fi tted
- 15A plug & lead fi tted
- 20A plug & lead fi tted
A terminal block for on-site connection, by a licensed electrician will be supplied inside the unit service compartment, indicated as:
- 1Ø+N+E
This unit must be installed in accordance with AS/NZS 60335.1
Some procedures in this manual require the power to the equipment to be turned off and
isolated. Turn the power OFF at the power point and unplug the power supply lead by the plug
body. If the power point is not readily accessible turn the equipment off at the isolation switch
or the circuit breaker in the switchboard. Attach a yellow “CAUTION-DO NOT OPERATE” tag.
This must be performed where relevant unless the procedures specify otherwise.
FAILURE TO DO SO MAY RESULT IN ELECTRIC SHOCK.
WARNING
Three Phase Units:
Supplied and fi tted with an appropriately rated plug and lead, indicated as:
- 32A plug & lead fi tted
A terminal block for on-site connection, by a licensed electrician will be supplied inside the unit service compartment, indicated as:
- 3Ø + N + E
Notes:
If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualifi ed persons in order to avoid a
hazard� Please contact Stoddart for parts and we will advise how to do this in order to avoid any electrical hazard
The power cable should be dry and/or isolated from moisture or water
Electrical Connection
Page 9
Due to continuous product research and development,
the information contained herein is subject to change without notice.
www.stoddart.com.au
www.stoddart.co.nz
Bench Tops (CH.BMC.U)
Under Counter Bench Tops
Finished opening sizes to bench top should be 5mm smaller than the well opening sizes shown below
As an example, the finished opening size in the bench for a 3 module Bain Marie will be 1052mm x 543mm
Ensure sufficient support to provided to the Bain Marie to support the weight of the unit when filled with water
Well sizes may vary slightly due to the manufacture process� It is recommended that measurements be taken on the actual unit being
fitted
WELL OPENING SIZES TO BAIN MARIE
Module Width Depth
3 1057 548mm
4 1397 548mm
5 1737 548mm
6 2077 548mm
7 2417 548mm
8 2757 548mm
Stainless Steel Benchtop Stone Benchtop
Installation
Cutout Sizes (CH.BMC.D)
Drop-in Bench Top
Drop-in Counter Line Bain Maries are designed to be installed into a cutout in a new or existing bench top
Take care to allow for the electrical, water and waste connections (refer to general drawing above)
Ensure sufficient support to provided to the Bain Marie to support the weight of the unit when filled with water
Sizes may vary slightly due to the manufacture process� It is recommended that measurements be taken on the actual unit being fitted
BENCH TOP CUTOUT SIZES
Module Width Depth
3 1180 805mm
4 1520 805mm
5 1860 805mm
6 2200 805mm
7 2540 805mm
8 2880 805mm
Page 10
Due to continuous product research and development,
the information contained herein is subject to change without notice.
www.stoddart.com.au
www.stoddart.co.nz
Install as shown when 1/1 module dividers are provided
½ dividers are sold separately
Element covers are placed over the top of the elements for protection
Without Element Cover With Element Cover
Without Divider With Divider
Bain Marie Element Covers & Dividers
Bain Marie Element Covers
Bain Marie Dividers
Installation
Page 11
Due to continuous product research and development,
the information contained herein is subject to change without notice.
www.stoddart.com.au
www.stoddart.co.nz
Technical Specifications
CH.BMC.D
SPECIFICATIONS
Model CH.BMC.D.GSF.3 / CH.BMC.D.GSB.3 CH.BMC.D.GSF.4 / CH.BMC.D.GSB.4 CH.BMC.D.GSF.5 / CH.BMC.D.GSB.5
Width 1197mm 1537mm 1877mm
Depth 825mm 825mm 825mm
Height 661mm 661mm 661mm
Bain Marie Capacity 3 x 1/1 Gastronorm Pans 4 x 1/1 Gastronorm Pans 5 x 1/1 Gastronorm Pans
Voltage 220-240V, 50Hz 220-240V, 50Hz 220-240V, 50Hz
Power (kW) 2.85kW 3.9kW 4.95kW
Current (average)
Connection 1 Phase, Neutral, Earth 3 Phase, Neutral, Earth
Temperature Range 65-90°C
Water Connection 15mm Diameter
Waste Connection 50mm Diameter
SPECIFICATIONS
Model CH.BMC.D.GSF.6 / CH.BMC.D.GSB.6 CH.BMC.D.GSF.7 / CH.BMC.D.GSB.7 CH.BMC.D.GSF.8 / CH.BMC.D.GSB.8
Width 2217mm 2557mm 2897mm
Depth 825mm 825mm 825mm
Height 661mm 661mm 661mm
Bain Marie Capacity 6 x 1/1 Gastronorm Pans 7 x 1/1 Gastronorm Pans 8 x 1/1 Gastronorm Pans
Voltage 220-240V, 50Hz 220-240V, 50Hz 220-240V, 50Hz
Power (kW) 5.7kW 6.75kW 7.5kW
Current (average)
Connection 3 Phase, Neutral, Earth
Temperature Range 65-90°C
Water Connection 15mm Diameter
Waste Connection 50mm Diameter
Specification
Page 12
Due to continuous product research and development,
the information contained herein is subject to change without notice.
www.stoddart.com.au
www.stoddart.co.nz
Specification
Page 13
Due to continuous product research and development,
the information contained herein is subject to change without notice.
www.stoddart.com.au
www.stoddart.co.nz
CH.BMC.U
SPECIFICATIONS
Model CH.BMC.U.GSF.3 / CH.BMC.U.GSB.3 CH.BMC.U.GSF.4 / CH.BMC.U.GSB.4 CH.BMC.U.GSF.5 / CH.BMC.U.GSB.5
Width 1203mm 1543mm 1883mm
Depth 691mm 691mm 691mm
Height 661mm 661mm 661mm
Bain Marie Capacity 3 x 1/1 Gastronorm Pans 4 x 1/1 Gastronorm Pans 5 x 1/1 Gastronorm Pans
Voltage 220-240V, 50Hz 220-240V, 50Hz 220-240V, 50Hz
Power (kW) 2.85kW 3.9kW 4.95kW
Current (average)
Connection 1 Phase, Neutral, Earth 3 Phase, Neutral, Earth
Temperature Range 65-90°C
Water Connection 15mm Diameter
Waste Connection 50mm Diameter
SPECIFICATIONS
Model CH.BMC.U.GSF.6 / CH.BMC.U.GSB.6 CH.BMC.U.GSF.7 / CH.BMC.U.GSB.7 CH.BMC.U.GSF.8 / CH.BMC.U.GSB.8
Width 2223mm 2563mm 2903mm
Depth 691mm 691mm 691mm
Height 661mm 661mm 661mm
Bain Marie Capacity 6 x 1/1 Gastronorm Pans 7 x 1/1 Gastronorm Pans 8 x 1/1 Gastronorm Pans
Voltage 220-240V, 50Hz 220-240V, 50Hz 220-240V, 50Hz
Power (kW) 5.7kW 6.75kW 7.5kW
Current (average)
Connection 3 Phase, Neutral, Earth
Temperature Range 65-90°C
Water Connection 15mm Diameter
Waste Connection 50mm Diameter
Specification
Page 14
Due to continuous product research and development,
the information contained herein is subject to change without notice.
www.stoddart.com.au
www.stoddart.co.nz
Specification
Page 15
Due to continuous product research and development,
the information contained herein is subject to change without notice.
www.stoddart.com.au
www.stoddart.co.nz
SPECIFICATIONS
Model CH.IBXX.BMC.U.GSX.3 CH.IBXX.BMC.U.GSX.4 CH.IBXX.BMC.U.GSX.5
Width 1380mm 1720mm 2060mm
Depth 1000mm 1000mm 1000mm
Height 1260mm 1260mm 1260mm
Bain Marie Capacity 3 x 1/1 Gastronorm Pans 4 x 1/1 Gastronorm Pans 5 x 1/1 Gastronorm Pans
Voltage 220-240V, 50Hz 220-240V, 50Hz 220-240V, 50Hz
Power (kW) 2.85kW 3.9kW 4.95kW
Current (average)
Connection 1 Phase, Neutral, Earth 3 Phase, Neutral, Earth
Temperature Range 65-90°C
Water Connection 15mm Diameter
Waste Connection 50mm Diameter
SPECIFICATIONS
Model CH.IBXX.BMC.U.GSX.6 CH.IBXX.BMC.U.GSX.7 CH.IBXX.BMC.U.GSX.8
Width 2400mm 2740mm 3080mm
Depth 1000mm 1000mm 1000mm
Height 1260mm 1260mm 1260mm
Bain Marie Capacity 6 x 1/1 Gastronorm Pans 7 x 1/1 Gastronorm Pans 8 x 1/1 Gastronorm Pans
Voltage 220-240V, 50Hz 220-240V, 50Hz 220-240V, 50Hz
Power (kW) 5.7kW 6.75kW 7.5kW
Current (average)
Connection 3 Phase, Neutral, Earth
Temperature Range 65-90°C
Water Connection 15mm Diameter
Waste Connection 50mm Diameter
CH.IBXX.BMC.U.GSF
CH.IBXX.BMC.U.GSF
Specification
Page 16
Due to continuous product research and development,
the information contained herein is subject to change without notice.
www.stoddart.com.au
www.stoddart.co.nz
10001260
900 360
1380
1720
2060
2400
2740
3080
Plan View
Front Elevation End Elevation
Specification
Page 17
Due to continuous product research and development,
the information contained herein is subject to change without notice.
www.stoddart.com.au
www.stoddart.co.nz
Operation
50
40 60
30 70
20 80
10 90
0%100
Initial Start-up & Operation
Bain Marie - Using as a Wet Unit
Before switching ON the unit - The element covers, dividers and shelves need to be placed in the unit
Fill unit with water using the ball valve provided or manually fill with a suitable container submerging the elements (minimum of 10mm
over the elements is required)� Hot or cold water can be used� Hot water will save on heating time and power consumption
A lemon slice or a few drops of lemon juice should be added to the water daily to reduce the build-up of scale in the unit
Place all pans and/or lids onto the bain marie
Turn on lights (if installed)
Turn the electronic controller ON and set to the required temperature (allow approximately 45mins to heat from room temperature)
Check water levels while the unit is in use, top up the water level as required ensuring elements remain submerged
Ensure the benches around the well are cleaned continuously to prevent contaminants entering the pans
When operating, the surfaces may be hot� Signage should be displayed for personal and customers to ensure no one will burn
themselves
This unit MUST be completely emptied/drained and re-filled with fresh water daily
Water MUST not be recycled� After being in the unit, all water MUST be treated as waste water Do NOT drink and/or serve to persons
WARNING
The water in the unit and the surfaces of this unit are
HOT when operating. Take caution and do NOT place
any part of the body in the water.
IMPORTANT
Water with a low chloride levels must be used!
Water with high chloride levels will cause corrosion to the unit.
For areas with a high chloride content (i.e. SA, WA or country
areas) demineralised water should be used in all cases.
Bain Marie - Using as a Dry Unit
Note: The Bain Marie is designed and recommended for wet operation, running the Bain Marie as a dry unit can create a wider range of
temperature variations�
Place all pans and/or lids onto the Bain Mare
Turn on lights (if installed)
Turn the electronic controller ON and set to the required temperature
Ensure the benches around the well are cleaned continuously to prevent contaminants entering the pans
When operating, the surfaces may be hot
Signage should be displayed for personal and customers to ensure no one will burn themselves
Page 18
Due to continuous product research and development,
the information contained herein is subject to change without notice.
www.stoddart.com.au
www.stoddart.co.nz
Operation
Note: The thermometer is meant as guide only It indicates the temperature of the water (when used as a wet unit) or the temperature under the
food pans (when used as a dry unit)� It does not indicate the temperature of the food� Do not use the top of the unit as a serving area�
Loading Bain Marie
All food MUST be pre-heated/cooked above the regulated 65°C serving temperature before placing in the unit� Attempting to cook food
with this unit can lead to food poisoning
The temperature reached on the temperature gauge is the water/air temperature, NOT the food temperature
It is important to regularly monitor the food temperature with a temperature probe to ensure it is above the regulated 65°C serving
temperature
Food Temperature
All storage of food should comply with local health standards and regulations
All pans should be cleaned and placed in night storage� No pans should be left in the unit
This unit is NOT designed to store product after hours� The unit MUST be switched OFF
If the unit is moved for night storage, ensure the castors are locked (mobile units only)
Food Storage
This unit MUST be completely emptied/drained and re-filled with fresh water daily
Water MUST not be recycled� After being in the unit, all water MUST be treated as waste water Do NOT drink and/or serve to persons
Bain Marie
Food Safety
After Service
Gastronorm (GN) Pans
All Gastronorm pans and extra dividers are sold separately
Each module can hold one 1/1 pan, two 1/2 pans, three 1/3 pans, four 1/4 pans, six 1/6 pans and nine 1/9 pans� Pan depths are 25mm,
65mm, 100mm and 150mm� Contact your distributor about the best possible depth for the product you intent to display
For 1/6 and 1/9 Gastronorm pans, extra dividers are required
Gastronorm Pans
IMPORTANT
This unit is not designed to cook products, it only maintains
them above the regulated 65°C serving temperature.
Ensure that the Bain Marie is switched ON and has reached operating temperature before placing any food in the unit
All food MUST be pre-heated/cooked above the regulated 65°C serving temperature before placing in the unit
Only Gastronorm pans are to be placed in the well
All food products must sit below top edge of the GN pan in order for the food to stay hot
Food should be left in the unit no longer than 2 hours
Page 19
Due to continuous product research and development,
the information contained herein is subject to change without notice.
www.stoddart.com.au
www.stoddart.co.nz
Temperature Adjustment
To display target set point; in programming mode it selects a parameter or confirm an operation.
To start a manual defrost.
To see the maximum stored temperature; in programming mode it browses the parameter codes or
increases the displayed value.
To see the minimum stored temperature; in programming mode it browses the parameter codes or
increases the displayed value.
To switch the instrument OFF, if onF = oFF.
Not enabled.
(DEF)
KEY FUNCTIONS:
(UP)
(DOWN)
To lock and unlock the keyboard.
To return to the room temperature display.
KEY COMBINATIONS:
1. Push and immediately release the SET key, the display will show the set point value
2. Push and immediately release the SET key or wait 5 seconds to display the probe value again
HOW TO SEE THE SET POINT:
1. Push the SET key for more than 2 seconds to change the set point value
2. The value of the set point will be displayed and the “°C” LED starts blinking
4. To memorise the new set point value push the SET key again or wait 10 seconds
HOW TO CHANGE THE SET POINT:
3. To change the set point value push the or arrows within 10 seconds
To enter in programming mode. (Contact the Stoddart Service Department)Note:
The temperature can be set between 65°C and 95°C� How to set the temperature is shown below
Different modes require different temperatures
The temperature probe only measures the temperature of the water/air, NOT the food temperature
Operation
Power
Heat Lamps can be switched ON or OFF with the GANTRY button on the unit
Lamps MUST be switched ON when the unit is in operation� Steam from operating as a wet unit and/or steam from foods can pool on
the lamps and damage the wiring
Surfaces
Nothing should be stored on the top of the gantry
When operating, the surfaces may be hot� Signage should be displayed for personal and customers to ensure no one will burn
themselves
Rear Sliding Doors
As glass can be HOT, ensure the rear door slide are OPENED and CLOSED with the glass pulls
IMPORTANT
Where a gantry is fi tted over the bain marie, ensure that the
lamps are always on when operating as a wet unit.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28

STODDART Culinaire CH.IBGJ.BMC.U.GSB User manual

Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI