D72
• Fitting: CNC cut Aluminium.
• Lamp type: 1 x GU5.3 Maximum 50W MR16 12V
• Voltage: 12V ~ 50Hz.
• Protection against electric shock: Class 3. Requires earthing.
• IP Rating: IP20. Protected against solid foreign objects of 12.5mm Ø and greater.
• Commercial / domestic use.
• Not suitable for outdoor use.
• Excluding Transformer - (Eurolux code: CO76 or CO79)
• Maximum Ambient temperature range: 20ºC - 40ºC.
• Dimensions: (Ø) 90mm x (D) 32mm
• Cut-out: (Ø) 80mm
D73
• Fitting: CNC cut Aluminium.
• Lamp type: 1 x GU5.3 Maximum 50W MR16 12V
• Voltage: 12V ~ 50Hz.
• Protection against electric shock: Class 3. Requires earthing.
• IP Rating: IP20. Protected against solid foreign objects of 12.5mm Ø and greater.
• Commercial / domestic use.
• Not suitable for outdoor use.
• Excluding Transformer - (Eurolux code: CO76 or CO79)
• Maximum Ambient temperature range: 20ºC - 40ºC.
• Dimensions: (L) 90mm x (W) 90mm x (D) 32mm
• Cut-out: (Ø) 80mm
D71
• Fitting: CNC cut Aluminium.
• Lamp type: 1 x GU5.3 Maximum 50W MR16 12V
• Voltage: 12V ~ 50Hz.
• Protection against electric shock: Class 3. Requires earthing.
• IP Rating: IP20. Protected against solid foreign objects of 12.5mm Ø and greater.
• Commercial / domestic use.
• Not suitable for outdoor use.
• Excluding Transformer - (Eurolux code: CO76 or CO79)
• Maximum Ambient temperature range: 20ºC - 40ºC.
• Dimensions: (Ø) 82mm x (D) 23mm
• Cut-out: (Ø) 70mm
SPECIFICATIONS
D71, D72, D73 - attachments:
If the external exible cable or cord of this luminaire is damaged, it should be exclusively
replaced by the manufacturer or his service agent or a similar qualied person in order to
avoid a hazard.
To ensure that you get maximum longevity and maximum use out of your luminaire, please
observe the following safety instructions.
Electrical products can cause death, injury, or damage to property.
Installation of the luminaire must be carried out by a qualied electrician, in accordance with
IMPORTANT SAFEGUARDS
Before installation always ensure the power supply is turned off.
1. Cut a hole in the ceiling as per “cut out”.
2. Connect to electrical supply.
3. Hold both clips on either side of downlight upwards and insert downlight into ceiling hole
ensuring the mains lead is not trapped.
4. Push tting upwards to snap rmly into position, ush with ceiling.
5. Insert the lamp by locating the pin connection holes within the lamp
holder, gently pushing the lamp into the holder and twisting into place.
6. Reconnect power.
NOTE: Always allow the lamp to cool sufciently before changing.
NOTE: To avoid heat transfer from downlight, allow a minimum gap of
about 200mm in height from downlight to ceiling / any materials above the downlight and
50mm all around the sides of the downlight.
Failure to do so could result in re.
INSTALLATION
CLEANING
• Before cleaning always ensure the power supply is turned off.
• Do not immerse the luminaire in water.
• No abrasive products, solvents, detergent may be used to clean this luminaire.
• Ensure that the tting does not come in contact with corrosive chemicals, etc.
• Use a soft cloth to clean.
SANS 10142. On completion of installation, ensure that the Certicate of Compliance
is updated.
• Before connecting the luminaire, ensure that voltage indicated on the rating label
corresponds with the mains voltage in your home.
• When changing the lamp, ensure that the power is turned off.
• Ensure that the correct lamp type and wattage is tted.
• This luminaire is checked in full for conformity to the quality standards and
safety requirements.
• The manufacturer / supplier is not responsible for any damage of properties and persons,
caused by the incorrect use or installation of the luminaire.
• Should you be unsure of how to install this luminaire correctly, please consult a professional
electrician or your supplier for assistance.
• Ensure all items/ components, threads and screws are tightly secured.
IMPORTANT:
• Tampering with this luminaire, I.E. Using silicon sealers or incorrect cabling, will invalidate
your warranty.
• When the protection glass is damaged, it should be replaced immediately. The luminaire
must not be used without the protection glass.
• Please check whether the connection of the power cord is safe and reliable
before installation.
• If your mains wiring differs in any way from diagram, consult a qualied electrician.
• Always ensure that the mains supply voltage is correct.
• Always replace the lamp with one of an identical rating and wattage.
• Choking hazard: May contain small parts. Keep away from children.
• Do not insert your ngers or any part of your body into the electrical contact and sockets of
this product whilst it is connected to the electrical supply.
• Item may vary slightly from the picture on the carton.
• Coastal humidity may effect the longevity of the luminaire.
1
2
Eglo W109SC Owner's manual
Verbatim 52606 User manual
Toshiba LEDEUS00091C Datasheet
Cooper Lighting 70 - 200W User manual
LG D8A0375EDF0 Datasheet