DFI PB64-BX User manual

PB64-BX/ZX

Rev. A+

System Board

Users Manual

39300911

Copyright

This publication contains information that is protected by copyright. No

part of it may be reproduced in any form or by any means or used to

make any transformation/adaptation without the prior written permission

from the copyright holders.

This publication is provided for informational purposes only. The

manufacturer makes no representations or warranties with respect to

the contents or use of this manual and specifically disclaims any express

or implied warranties of merchantability or fitness for any particular purpose.

The user will assume the entire risk of the use or the results of the use of

this document. Further, the manufacturer reserves the right to revise this

publication and make changes to its contents at any time, without obligation

to notify any person or entity of such revisions or changes.

Trademarks

Microsoft

®

MS-DOS

®

, Windows

TM

, Windows

®

95 and Windows

®

98 are

registered trademarks of Microsoft Corporation. Intel

®

, Pentium

®

II,

Pentium

®

III and Celeron

TM

are registered trademarks of Intel Corporation.

Award is a registered trademark of Award Software, Inc. Other trademarks

and registered trademarks of products appearing in this manual are the

properties of their respective holders.

Caution:

Danger of explosion if battery incorrectly replaced.

Replace only with the same or equivalent type recommended by the

manufacturer.

Dispose of used batteries according to the battery manufacturers

instructions.

FCC and DOC Statement on Class B

This equipment has been tested and found to comply with the limits

for a Class B digital device, pursuant to Part 15 of the FCC rules.

These limits are designed to provide reasonable protection against

harmful interference when the equipment is operated in a residential

installation. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with

the instruction manual, may cause harmful interference to radio

communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the

following measures:

 Reorient or relocate the receiving antenna.

 Increase the separation between the equipment and the receiver.

 Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

 Consult the dealer or an experienced radio TV technician for

help.

Notice:

1. The changes or modifications not expressly approved by the

party responsible for compliance could void the user's authority

to operate the equipment.

2. Shielded interface cables must be used in order to comply with

the emission limits.

Table of Contents

Chapter 1 - Introduction

1.1 Features and Specifications..................................................................................

1.2 Package Checklist.........................................................................................................

Chapter 2 - Hardware Installation

2.1 System Board Layout .............................................................................................

2.2 System Memory.............................................................................................................

2.3 DIP Switch Settings for Processors............................................................

2.4 Jumper Settings for the CPUs Front Side Bus................................

2.5 Jumper Settings for Clearing CMOS Data..........................................

2.6 Jumper Settings for Wake-On-Keyboard/Wake-On-Mouse......

2.7 Connecting the Ribbon Cables and Wires of the Ports

and Connectors.............................................................................................................

Chapter 3 - Award BIOS Setup Utility

3.1 The Basic Input/Output System.....................................................................

3.1.1 Standard CMOS Setup....................................................................

3.1.2 BIOS Features Setup..........................................................................

3.1.3 Chipset Features Setup....................................................................

3.1.4 Power Management Setup............................................................

3.1.5 PNP/PCI Configuration....................................................................

3.1.6 Load Fail-Safe Settings......................................................................

3.1.7 Load Optimal Settings......................................................................

3.1.8 Integrated Peripherals.........................................................................

3.1.9 Supervisor Password..........................................................................

3.1.10 User Password.........................................................................................

3.1.11 IDE HDD Auto Detection...........................................................

3.1.12 Save & Exit Setup.................................................................................

3.1.13 Exit Without Saving..............................................................................

Chapter 4 - Supported Softwares

4.1 Desktop Management Interface.....................................................................

4.2 Hardware Doctor Utility........................................................................................

4.3 Patch Utility and drivers........................................................................................

6

11

33

36

39

43

48

50

51

55

56

57

12

14

15

16

17

18

19

58

61

63

64

66

Appendix A - System Error Messages

A.1 POST Beep.......................................................................................................................

A.2 Error Messages..............................................................................................................

Appendix B - Troubleshooting

B.1 Troubleshooting Checklist....................................................................................

6

1.1 Features and Specifications

1.1.1 Features

Chipset

PB64-BX

 Intel



440BX AGPset

 ESS Solo-1 PCI AudioDrive

PB64-ZX

 Intel



440ZX-100 AGPset

 ESS Solo-1 PCI AudioDrive

Processor

The system board is equipped with a 242-pin Slot 1 processor slot

for installing an Intel Pentium



II/Pentium



III processor that is

packaged in an SECC/SECC 2 or an Intel Celeron

TM

processor

(SEPP). It is also equipped with a switching voltage regulator that

automatically detects 1.30V to 3.5V.

 450/100MHz or 500/100MHz Pentium



III processor

 233/66MHz, 266/66MHz, 300/66MHz, 333/66MHz,

350/100MHz, 400/100MHz or 450/100MHz Pentium



II

processor

 266/300/300A/333/366/400/433MHz Celeron

TM

processor

(SEPP for Slot 1)

System Memory

 PB64-BX

- 16MB to 384MB memory using unbuffered DIMMs

- 32MB to 768MB memory using registered DIMMs

- Three 168-pin DIMM sockets

- Uses x64 or x72 PC SDRAM, 3.3V

: PC-66 SDRAM DIMM for 66MHz FSB processors

: PC-100 SDRAM DIMM for 100MHz FSB processors

- ECC supported (uses x72 PC SDRAM DIMM)

Chapter 1 - Introduction

1

Introduction

7

Expansion Slots

The system board is equipped with 1 dedicated AGP slot. AGP is an

interface designed to support high performance 3D graphics cards. It

utilizes a dedicated pipeline to access system memory for texturing,

z-buffering and alpha blending; delivering up to 533MB/sec.

bandwidth for 3D graphics applications. AGP in this system board

will deliver faster and better graphics with your PC.

The system board is also equipped with 4 dedicated PCI slots, 2

dedicated 16-bit ISA slots. All PCI and ISA slots are bus masters

except PCI 4 in the PB64-ZX which is slave only.

Onboard Audio Features

 Sound Blaster, Sound Blaster Pro and WSS compatible

 Supports PC games and applications

 Sample rates from 4KHz up to 48KHz

 Full duplex operation for simultaneous record and playback

 ESS proprietary AudioRack application

* Supported only when PB64-BX

uses registered DIMMs.

DIMMs

2MBx64/x72

4MBx64/x72

8MBx64/x72

16MBx64/x72

32MBx64/x72

Memory Size

16MB

32MB

64MB

128MB

256MB*

DIMMs

2MBx64

4MBx64

8MBx64

16MBx64

Memory Size

16MB

32MB

64MB

128MB

PB64-ZXPB64-BX

 PB64-ZX

- 16MB to 256MB memory using unbuffered DIMMs

- Two 168-pin DIMM sockets

- Uses x64 PC SDRAM, 3.3V

: PC-66 SDRAM DIMM for 66MHz FSB processors

: PC-100 SDRAM DIMM for 100MHz FSB processors

Introduction

1

8

Desktop Management Interface (DMI)

The system board comes with a DMI 2.0 built into the BIOS. The

DMI utility in the BIOS automatically records various information

about your system configuration and stores these information in the

DMI pool, which is a part of the system board's Plug and Play

BIOS. DMI, along with the appropriately networked software, is

designed to make inventory, maintenance and troubleshooting of

computer systems easier. Refer to Chapter 4 for instructions on

using the DMI utility.

ATX double deck ports

 2 USB ports

 2 DB-9 serial ports

 1 DB-25 parallel port

 1 mini-DIN-6 PS/2 keyboard port

 1 mini-DIN-6 PS/2 mouse port

 1 game/MIDI port

 3 audio jacks: line-out, line-in and mic-in

Connectors

 1 connector for IrDA interface

 2 IDE connectors

 1 floppy connector

 1 20-pin ATX power supply connector

 1 3-pin WOL (Wake-On-LAN) connector

 3 CD audio-in connectors

 3 fan connectors for CPU, chassis and AGP fans

PCI Bus Master IDE Controller

 Two PCI IDE interfaces support up to four IDE devices

 Ultra DMA/33 supported (Synchronous Ultra DMA mode -

data transfer rate up to a maximum of 33MB/sec.)

 PIO Mode 3 and Mode 4 Enhanced IDE (data transfer rate up

to 16.6MB/sec.)

 Bus mastering reduces CPU utilization during disk transfer

 Supports ATAPI CD-ROM, LS-120 and ZIP and SCSI sequential

boot-up

1

Introduction

9

IrDA Interface

The system board is equipped with an IrDA connector for wireless

connectivity between your computer and peripheral devices. It

supports peripheral devices that meet the IrDA or ASKIR standard.

USB Ports

The system board is equipped with two USB ports. USB allows

data exchange between your computer and a wide range of

simultaneously accessible external Plug and Play peripherals.

BIOS

 Award BIOS, Windows



95/98 Plug and Play compatible

 Flash EPROM for easy BIOS upgrades

 Includes NCR 810 SCSI BIOS

 2MB flash memory

1.1.2 System Health Monitor Functions

The system board is capable of monitoring the following system

health conditions.

 Monitors processor/system temperature and processor overheat

alarm

 Monitors 1.5V/3.3V/±5V/±12V/VCORE voltages and failure

alarm

 Monitors processor/chassis fan speed and failure alarm

 Automatic processor/chassis fan control

 Read back capability that displays accurate temperature, voltage

and fan speed

Introduction

1

10

1.1.3 Intelligence

Automatic CPU/Chassis Fan Off

The CPU and chassis fans will automatically turn off once the system

enters the Suspend mode.

Dual Function Power Button

Depending on the setting in the BIOS setup, this switch will allow

the system to enter the Soft-Off or Suspend mode.

External Modem Ring-on

The Modem Ring-on feature allows the system that is in the

Suspend mode or Soft Power Off mode to wake-up/power-on to

respond to incoming calls.

Note:

This feature supports external modem only.

RTC Timer to Power-on the System

The RTC installed on the system board allows your system to

automatically power-on on the set date and time.

Wake-On-LAN Ready

The Wake-On-LAN function allows the network to remotely wake

up a Soft Power Down (Soft-Off) PC. Your LAN card must support

the remote wakeup function.

Important:

The 5VSB power source of your power supply must support

≥

720mA (minimum).

Wake-On-Keyboard/Wake-On-Mouse

This function allows you to use the keyboard or mouse to power-on

the system. Refer to Jumper Settings for Wake-On-Keyboard/Wake-

On-Mouse in Chapter 2 and Keyboard/Mouse Power On in the

1

Introduction

11

Integrated Peripherals setup of the Award BIOS in Chapter 3 for

more information.

Important:

 The power button will not function once a keyboard

password has been set in the KB Power On Password

field of the Integrated Peripherals setup. You must type the

correct password to power-on the system.

 The 5VSB power source of your power supply must

support

≥

720mA (minimum).

ACPI

The system board is designed to meet the ACPI (Advanced

Configuration and Power Interface) specification. ACPI has energy

saving features that enables PCs to implement Power Management

and Plug-and-Play with operating systems that support OS Direct

Power Management.

Virus Protection

Most viruses today destroy data stored in hard drives. The system

board is designed to protect the boot sector and partition table of

your hard disk drive.

1.2 Package Checklist

The system board package contains the following items:

þ The system board

þ A users manual

þ One 40-pin IDE hard disk cable

þ One 34-pin floppy disk drive cable

þ One CD

If any of these items are missing or damaged, please contact your

dealer or sales representative for assistance.

12

2.1 System Board Layout

Chapter 2 - Hardware Installation

PB64-BX

2

Hardware Installation

13

PB64-ZX

Note:

The illustrations on the following pages are based on the PB64-BX

system board, which is the board equipped with three DIMM sockets.

Warning:

Electrostatic discharge (ESD) can damage your system board, processor, disk

drives, add-in boards, and other components. Perform the upgrade instruction

procedures described at an ESD workstation only. If such a station is not

available, you can provide some ESD protection by wearing an antistatic wrist

strap and attaching it to a metal part of the system chassis. If a wrist strap is

unavailable, establish and maintain contact with the system chassis throughout

any procedures requiring ESD protection.

2

14

Hardware Installation

2.2 System Memory

The PB64-BX system board is

equipped with three 168-pin DIMM

(Dual In-line Memory Module)

sockets that support x64/x72

unbuffered or registered PC

SDRAM DIMM, 3.3V.

The PB64-ZX system board is

equipped with two 168-pin DIMM

(Dual In-line Memory Module)

sockets that support x64 unbuffered

PC SDRAM DIMM, 3.3V.

PC SDRAM (Synchronous Dynamic

Random Access Memory) uses a fast memory interface technology

that includes using the clock on the chip to synchronize with the

CPU clock so that the timing of the memory chips and the timing of

the CPU are synchronized. This saves time during transmission of

data, subsequently increasing system performance.

Pin 1

Notch

Key

Tab

2.2.1 Installing the DIM Module

A DIM module simply snaps into a DIMM socket on the system

board. Pin 1 of the DIM module must correspond with Pin 1 of the

socket.

2

Hardware Installation

15

2.3 DIP Switch Settings for Processors

The table on the next page shows the supported processors and

their corresponding DIP switch settings (SW1). There are 4 switches

on SW1. The black rectangle in the diagram denotes the part that is

protruding, the adjustable switch. Make sure SW1 is set correctly

before applying power, otherwise you will not be able to power-on

the system.

1. Pull the tabs which are at the ends of the socket to the side.

2. Position the DIMM above the socket with the notches in the

module aligned with the keys on the socket.

3. Seat the module vertically into the socket. Make sure it is

completely seated. The tabs will hold the DIMM in place.

In the example above:

Switch 1: Off

Switch 2: Off

Switch 3: On

Switch 4: On

2

16

Hardware Installation

2.4 Jumper Settings for the CPUs Front Side Bus

Jumper JP3

CPUs Front Side Bus Select

The default setting of jumper JP3 is

Auto - the system will automatically

run according to the FSB of the

processor. If you wish to overclock a

66MHz FSB processor to 100MHz,

set pins 1, 2 and 3 to Off. If you

want a 100MHz FSB processor to

run at 66MHz, set pins 2 and 3 to

On. Refer to the figure on the next

page.

Warning:

Overclocking a 66MHz FSB

processor to 100MHz will

provide better system performance. However, not all 66MHz

FSB processors are capable of running at 100MHz bus speed.

Therefore, if you are unable to boot your system when set at

100MHz, make sure to set JP3 back to its default setting.

Note:

Intel Pentium



II, Intel Pentium



III processors and Intel Celeron

TM

processors support VID (Voltage Identification). The switching voltage

regulator on the system board will automatically set the voltage regulator

according to the voltage of the processor.

233MHz 350MHz 3.5x

266MHz 400MHz

4x

300MHz 450MHz 4.5x

333MHz 5x

Processor

SW1

66MHz 100MHz

Frequency

Ratio

Future

processor

5.5x

Processor

SW1

66MHz 100MHz

Frequency

Ratio

400MHz

Future

processor

433MHz

Future

processor

Future

processor

Future

processor

Future

processor

Future

processor

6x

6.5x

7x

7.5x

8x

Future

processor

Future

processor

500MHz

366MHz

2

Hardware Installation

17

2.5 Jumper Settings for Clearing CMOS Data

Jumper JP4

Clear CMOS Data

If, for some reason, the CMOS data

becomes corrupted or you forgot the

supervisor/user/keyboard password,

the system can be reconfigured with

the default values stored in the ROM

BIOS. To load the default values,

power off your system and unplug

the power cord. Set JP4 pins 2 and

3 to On. Wait for a few seconds and

set JP4 back to its default setting,

pins 1 and 2 On. You may now plug

the power cord and power-on your

system.

Jumper JP3s settings are shown below.

1

2

3

1

2

3

1

2

3

2-3 On: 66MHz

1-2 On: Auto

(default)

1-2-3 Off: 100MHz

2-3 On:

Clear CMOS Data

1-2 On: Normal

(default)

1

23

1

23

2

18

Hardware Installation

2.6 Jumper Settings for Wake-On-Keyboard/

Wake-On-Mouse

Jumper JP1

Wake-On-Keyboard/Wake-On-Mouse

The system board supports the

Wake-On-Keyboard/Wake-On-Mouse

function. This function allows you to use

the keyboard or mouse to power-on

the system. By default, JP1 is disabled.

To use this function, set JP1 to 2-3

On. Keyboard/Mouse Power On in

the Integrated Peripherals setup of the

Award BIOS must be set accordingly.

Refer to chapter 3 for details.

Warning:

1. If JP1 was previously enabled

with a password set in the

KB Power On Password field, and now you wish to disable

the Wake-On-Keyboard (password) function, make sure to

set the Keyboard/Mouse Power On field to Disabled prior

to setting JP1 to disabled. You will not be able to boot up

the system if you fail to do so.

2. The power button will not function once a keyboard

password has been set in the KB Power On Password

field of the Integrated Peripherals setup. You must type the

correct password to power-on the system.

3. The 5VSB power source of your power supply must

support

≥

720mA (minimum).

2-3 On: Enable1-2 On: Disable

(default)

1

23

1

23

2

Hardware Installation

19

2.7.2 PS/2 Mouse and Keyboard Ports

The PS/2 mouse port uses IRQ12. If a

mouse is not connected to this port,

the system will reserve IRQ12 for other

expansion cards.

Warning:

Make sure to turn off your

computer prior to connecting or

disconnecting a mouse or

keyboard. Failure to do so may

damage the system board.

2.7 Connecting the Ribbon Cables and Wires of

the Ports and Connectors

2.7.1 Serial Ports

The built-in serial ports are RS-232C

asynchronous communication ports with

16C550A-compatible UARTs that can

be used with modems, serial printers,

remote display terminals, and other

serial devices. You can set the serial

ports I/O address in the Integrated Pe-

ripherals setup of the Award BIOS.

2

20

Hardware Installation

2.7.3 Parallel Ports

The system board has a standard

printer port for interfacing your PC to a

parallel printer. It supports SPP, ECP and

EPP modes. You can set the ports

mode in the Integrated Peripherals

setup of the Award BIOS.

Setting

SPP

(Standard Parallel Port)

ECP

(Extended Capabilities Port)

EPP

(Enhanced Parallel Port)

Function

Allows normal speed operation but

in one direction only.

Allows parallel port to operate in

bidirectional mode and at a speed

faster than the SPPs data transfer

rate.

Allows bidirectional parallel port op-

eration at maximum speed.

Page is loading ...

DFI PB64-BX User manual

This manual is also suitable for

DFI PB64-BX User manual

Related papers

Other documents