Linksys EZXS55W - EtherFast 10/100 Workgroup Switch User manual

Instant EtherFast

®

Series

Use this Guide to install the following:

EZXS55W ver. 3

EZXS88W ver. 3

EZXS16W ver. 2

EtherFast

®

10/100

Workgroup Switches

Quick Installation

Guide

Table of Contents

English 2

French 6

German 10

Italian 14

Portuguese 18

Spanish 22

Table of Contents

Installing the 10/100 Workgroup Switches 4

Overview 4

Installation 4

Uplinking to Other Switches and Hubs 4

2 3

COPYRIGHT & TRADEMARKS

mark of Linksys. Microsoft, Windows, and the Windows logo are registered trademarks of

Microsoft Corporation. All other trademarks and brand names are the property of their

respective proprietors.

FCC STATEMENT

The Instant EtherFast 10/100 Workgroup Switches have been tested and found to comply

with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful interference in a resi-

dential installation. This equipment generates, uses, and can radiate radio frequency ener-

gy and, if not installed and used according to the instructions, may cause harmful interfer-

ence to radio communications. However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does cause harmful interference to radio

or television reception, which is found by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment or device

• Connect the equipment to an outlet other than the receiver’s

• Consult a dealer or an experienced radio/TV technician for assistance

QIG-Ezxs55w/88w/16w-EU 20619C TE

For product support, contact us at the addresses below:

Email [email protected]

Web http://www.linksys.com/international

10/100 Workgroup Switches

EZXS16W only:

The 10/100 16-Port Switch is equipped with a crossover button (labeled

MDI/MDIX) that enables port 16 to be used as the switch’s uplink port. To uti-

lize the port’s uplink capability, the MDI/MDIX button must be pressed in. If

the button is not depressed, port 16 will function as a normal 10/100 port and

cannot be utilized as an Uplink port.

54

Instant EtherFast

®

Series

Installing the 10/100 Workgroup

Switches

Follow these instructions when installing the EtherFast

®

Switch. If at any time

during the installation you encounter problems, contact Linksys Technical

Support.

If you run into any problems with this installation or need any further infor-

mation, visit us on the World Wide Web at http:\\www.linksys.com. Also, for

the most current technical information and up-to-date specifications, refer to

the Linksys web site at http:\\www.linksys.com.

Your Switch’s rear panel has either 5, 8, or 16 standard RJ-45 ports (depending

on the model). Each port automatically detects the speed and duplex of the

attached cabling to a network card, switch, hub, or other networking peripher-

al. The ports operate in either full or half duplex, which lets you run at speeds

of 10Mbps, 20Mbps, 100Mbps or 200Mbps.

Each port on your Switch can connect to workstations, file servers, hubs,

switches, bridges, routers or other network peripheral. Connections to the

switch require UTP Category 5 network cabling with RJ-45 connectors, not

to exceed 100 meters (328 feet) in length.

To connect a computer directly to the switch, plug one end of the cable into the

switch, then plug the other end of the cable into the computer's network adapter.

EZXS55W ver. 3 & EZXS88W ver. 3 only:

If the Uplink port is in use (connected to another switch, etc.), the 10/100

Workgroup Switch’s port next to the Uplink port must remain empty and

unused. As with most switches, the 10/100 Workgroup Switch’s Uplink port

and the port adjacent to it are joined together inside the switch, and one cannot

be used while the other is in use.

Installation

Uplinking to Other Switches and Hubs

Overview

Page is loading ...

Printed in the USA.

www.linksys.com

Linksys EZXS55W - EtherFast 10/100 Workgroup Switch User manual

This manual is also suitable for

Linksys EZXS55W - EtherFast 10/100 Workgroup Switch User manual

in other languages

Related papers

Other documents