Poulan Pro 220 LE User manual

Brand: Poulan Pro

Model: 220 LE

Category: Power chainsaws

Type: User manual

220 LE / 260 LE

WARNING:

Read and follow all Safety Rules and Operating Instructions before

using this product. Failure to do so can result in serious injury.

ADVERTENCIA:

Lea el manual de instrucciones y siga todas las advertencias e en-

strucciones de seguridad. El no hacerlo puede resultar en lesiones

graves.

AVERTISSEMENT:

Lire le manuel d’instructions et bien respecter tous les avertisse-

ments et toutes les instructions de sécurité. Tout défaut de le faire

pourrait entraîner des blessures graves.

Electrolux Home Products, Inc.

250 Bobby Jones Expressway

Augusta, GA 30907

ENGLISH

ESP AÑOL

FRANÇAIS

530163637 11/22/02

Electrolux Canada Corporation

6150 McLaughlin Road

Mississauga, Ontario L5R 4C2

2002 Electrolux Home Products, Inc.

For Occasional Use Only

Instruction Manual

Manual de Instrucciones

Manuel d’Instructions

IDENTIFICATION OF SYMBOLS

W ARNING!

This chain

saw can be dangerous! Care-

less orimproperuse cancause

serious or even fatal injury.

Read and understand the

instruction manual before

using the chain saw.

Always use two hands when operating the chain saw .

WARNING!

Contacting the guide bar tip with any object

should be avoided; tip contact may cause the guide bar to

movesuddenly upward andbackward, whichmay causese-

rious injury.

Always wearappropriate earprotection, eye protection and head protection.

XX_

Measured maximum kickback value without chain brake for the bar

and chain combination on the label.

SAFETY RULES

WARNING:

Always disconnect

spark plug wire and place wire where it can-

not contact spark plug to prevent accidental

starting when setting up, transporting, ad-

justing or making repairs except carburetor

adjustments.

Because a chain saw is a high-speed wood-

cutting tool, special safety precautions must

be observed to reduce the risk of accidents.

Careless or improper use of this tool can

cause serious injury.

PLAN AHEAD

Read this manual carefully until you com-

pletely understand and can follow all safety

rules, precautions, and operating instruc-

tions before attempting to use the unit.

Restrict the use of your saw to adult users

who understand and can follow safety

rules, precautions, and operating instruc-

tions found in this manual.

Wear protective gear. Always use steel-

toed safety footwear with non-slip soles;

snug-fitting clothing; heavy-duty, non-slip

gloves; eye protection such as non-fog-

ging, vented goggles or face screen; an

approved safety hard hat; and sound barri-

ers (ear plugs or mufflers) to protect your

hearing. Regular users should have hear-

ing checked regularly as chain saw noise

can damage hearing. Secure hair above

shoulder length.

Snug

Fitting

Clothing

Safety

Shoes

Safety Chaps

Heavy Duty

Gloves

Eye

Protection

Hearing

Protection

Safety Hat

Keep all parts of your body away from the

chain when the engine is running.

Keep children, bystanders, and animals a

minimum of 30 feet (10meters) away from

the work area. Do not allow other people

or animals to be near the chain saw when

starting or operating the chain saw.

Do not handle or operate a chain saw

whenyouarefatigued, ill, or upset, orif you

have taken alcohol, drugs, or medication.

You must be in good physical condition

and mentally alert. Chain saw work is

strenuous. If you have any condition that

might be aggravated by strenuous work,

check with your doctor before operating a

chain saw.

Carefully planyour sawing operation inad-

vance. Donot start cutting until youhavea

clear workarea, secure footing, and, if you

are felling trees, a planned retreat path.

OPERATE YOUR SAW SAFELY

Donot operate a chain sawwith one hand.

Serious injury to the operator, helpers, by-

standers or any combination of these per-

sons may result from one-handed opera-

tion. A chain saw is intended for

two-handed use.

Operate the chain saw only in a well-venti-

lated outdoor area.

Do not operate saw from a ladder or in a

tree.

Make sure the chain will not make contact

with any object while starting the engine.

Never try to start the saw when the guide

bar is in a cut.

Do not put pressure on the saw at the end

of the cut. Applying pressure can cause

you to lose control when the cut is com-

pleted.

Stop the engine before setting the saw

down.

Do not operate a chain saw that is dam-

aged, improperly adjusted, or not com-

pletely and securely assembled. Always

replace bar, chain, hand guard, or chain

brake immediately if it becomes damaged,

broken or is otherwise removed.

With the engine stopped, hand carry the

chain saw with the muffler away from your

body, and the guide bar and chain to the

rear, preferably covered with a scabbard.

MAINTAIN YOUR SAW IN GOOD

WORKING ORDER

Have all chain sawservice performed by a

qualified service dealer with the exception

of the items listed in the maintenance sec-

tion of this manual. Forexample, if improp-

er tools are used to remove or hold the fly-

wheel when servicing the clutch, structural

damage to the flywheel can occur and

cause the flywheel to burst.

Make certain the saw chain stops moving

when the throttle trigger is released. For

correction, refer to CARBURETOR AD-

JUSTMENTS.

Never modify your saw in any way.

Keep the handles dry,clean, and free of oil

or fuel mixture.

Keep fuel and oil caps, screws, and fas-

teners securely tightened.

Use only Poulan PRO

accessories and

replacement parts as recommended.

HANDLE FUEL WITH CAUTION

Do not smoke while handling fuel or while

operating the saw.

Eliminate all sources of sparks or flame in

the areas where fuel is mixed or poured.

There should benosmoking, open flames,

orworkthat couldcause sparks. Allow en-

gine to cool before refueling.

Mix and pour fuel in an outdoor area on

bare ground; store fuel in a cool, dry, well

ventilated place; and use an approved,

marked container for all fuel purposes.

Wipe up all fuel spills before starting saw.

Move at least 10 feet (3meters) from fuel-

ing site before starting engine.

Turn the engine off and let saw cool in a

non-combustible area, not on dry leaves,

straw, paper, etc. Slowly remove fuel cap

and refuel unit.

Store theunitandfuel inanarea wherefuel

vapors cannot reach sparks or open

flames from water heaters, electric motors

or switches, furnaces, etc.

KICKBACK

WARNING:

Avoid kickback which

can result in serious injury. Kickback is the

backward, upward orsudden forward motion

of the guide bar occurring when the saw

chain near the upper tip of theguide barcon-

tacts any object such as a log or branch, or

when the wood closes in and pinches the

sawchain in thecut. Contacting aforeign ob-

ject in the wood can also result in loss of

chain saw control.

Rotational Kickback canoccur when the

moving chain contacts an object at the up-

per tip of the guide bar . This contact can

cause the chain to dig into the object,

which stops the chain for an instant. The

result is a lightning fast, reverse reaction

which kicks the guide bar up and back to-

ward the operator.

Pinch-Kickback can occur when the the

wood closes in and pinches the moving

saw chain in the cut along the top of the

guide bar and the saw chain is suddenly

stopped. This sudden stopping of the

chain results in a reversal of the chain

force used to cut wood and causes the

sawtomoveintheopposite direction ofthe

chain rotation. The saw is driven straight

back toward the operator.

Pull-In can occur when the moving chain

contacts a foreign object in the wood in the

cut along the bottom of the guide bar and the

sawchain is suddenlystopped. Thissudden

stopping pulls the saw forwar d and away

fromtheoperatorand could easily cause the

operator to lose control of the saw.

A v oid Pinch--Kickback:

Be extremely aware of situations or ob-

structions that can cause material topinch

the top of or otherwise stop the chain.

Do not cut more than one log at a time.

Do not twist the saw as the bar is with-

drawn from an undercut when bucking.

Avoid Pull-- I n:

Always begin cutting with the engine atfull

speed and the saw housing against wood.

Use wedges made of plastic or wood.

Never use metal to hold the cut open.

Kickback Path

Avoid Obstructions

Clear The Working Area

REDUCE THE CHANCE OF

KICKBACK

Recognize that kickback can happen.

With a basic understanding of kickback,

you can reduce the element of surprise

which contributes to accidents.

Never let themoving chain contact anyob-

ject at the tip of the guide bar.

Keep the working area free from obstruc-

tionssuchasothertrees, branches, rocks,

fences, stumps, etc. Eliminate or avoid

any obstruction that your saw chain could

hit while you are cutting. When cutting a

branch, do not let the guide bar contact

branch or other objects around it.

Keep your saw chain sharp and properly

tensioned. A loose or dull chain can in-

crease the chance of kickback occurring.

Follow manufacturer’s chain sharpening

and maintenance instructions. Check ten-

sion at regular intervals with the engine

stopped, never with the engine running.

Make sure the chain brake nuts are se-

curely tightened after tensioning thechain.

Begin and continue cutting at full speed. If

the chain is moving at a slower speed,

there is greater chance of kickback occur-

ring.

Cut one log at a time.

Use extreme caution when re-entering a

previous cut.

Do not attempt cuts starting with the tip of

the bar (plunge cuts).

Watch for shifting logs or other forces that

could close a cut and pinch or fall into

chain.

Use the Reduced--Kickback Guide Bar

and Low--Kickback Chain specified for

your saw.

MAINTAIN CONTROL

Never reverse

hand positions

Stand to the left

of the saw

Thumb on

underside of

handlebar

Thumb on underside of

handlebar

Elbow locked

Keep agood, firm grip on thesawwith both

hands when the engine is running and

don’t let go. Afirmgrip willhelp youreduce

kickback and maintain control of the saw.

Keep the fingers of your left hand encir-

cling and your left thumb under the front

handlebar. Keep your right hand com-

pletely around the rear handle whether

your are right handed orleft handed. Keep

your left arm straight with the elbow

locked.

Position your left hand on the front handle-

bar so it is in a straight line with your right

hand on the rear handle when making

bucking cuts. Never reverse right and left

hand positions for any type of cutting.

Stand with yourweight evenly balanced on

both feet.

Stand slightly to the left side of the saw to

keep your body from being in a direct line

with the cutting chain.

Do not overreach. You could be drawn or

thrown off balance and lose control of the

saw.

Donot cut above shoulder height. Itisdiffi-

cult to maintain control of saw above

shoulder height.

KICKBACK SAFETY FEATURES

WARNING:

The following features

are included on your saw to help reduce the

hazard of kickback; however, such features

will not totally eliminate this danger. As a

chain saw user,do not rely onlyon safety de-

vices. You must follow all safety precau-

tions, instructions, and maintenance in this

manual to help avoid kickback and other

forces which can result in serious injury.

Reduced--Kickback Guide Bar, designed

with a small radius tip which reduces the

size of the kickback danger zone on the

bar tip. A Reduced--Kickback Guide Bar

has been demonstrated to significantly re-

duce the number and seriousness of kick-

backs when tested in accordance with

safety requirements for gasoline powered

chain saws as set by ANSI B175.1.

Small Radius Tip

Reduced Kickback Symmetrical Guide Bar

Symmetrical Guide Bar

Large Radius Tip

Low--Kickback Chain, designed with a

contoured depth gauge and guard link

which deflect kickback force and allow

wood togradually ride intothe cutter.Low--

Kickback Chain has met kickback per-

formance requirements when tested on a

representative sample of chain saws be-

low 3.8 cubic inch displacement specified

in ANSI B175.1.

Low---Kickback

Chain

Not a Low---Kickback Chain

Can Obstruct Material

Contoured Depth Gauge

Elongated Guard Link

Deflects

kickback force

and allows wood

to gradually ride

into cutter

Front Hand Guard, designed to reduce the

chanceof yourleft hand contacting thechain

if your hand slips off the front handlebar.

Position of front and rear handlebars, de-

signed with distance between handles and

“in-line” with each other. The spread and

“in-line” position of the hands provided by

this design work together to give balance

and resistance in controlling the pivot of

the saw back toward the operator if kick-

back occurs.

CHAIN BRAKE AND CKA ANGLE

Chain Brake, designed to stop the chain in

the event of kickback.

WARNING:

WE DO NOT REP-

RESENT AND YOU SHOULD NOT AS-

SUME THAT THE CHAIN BRAKE WILL

PROTECT YOU IN THE EVENT OF A

KICKBACK. Kickback is a lightning fast ac-

tion which throws the bar and rotating chain

back and up toward the operator. Kickback

can be caused by allowing contact of the bar

tip in the danger zone with any hard object.

Kickback canalso becaused bypinching the

sawchain along thetopofthe guide bar. This

action may push the guide bar rapidly back

toward the operator. Either of these events

may cause you to lose control of the saw

which could result in serious injury or even

death. DO NOT RELY UPON ANY OFTHE

DEVICES BUILT INTO YOUR SAW. YOU

SHOULDUSETHESAW PROPERLYAND

CAREFULLY TO AVOID KICKBACK. Re-

duced--kickback guide bars and low--kick-

back saw chains reduce the chance and

magnitude of kickback and are recom-

mended. Your sawhas a low kickback chain

and bar as original equipment. Repairs on a

chain brake should be made by an autho-

rized servicing dealer. Take your unit to the

place of purchase if purchased from a ser-

vicing dealer, or to the nearest authorized

master service dealer.

Tipcontactinsomecasesmaycause alight-

ning fast reverse REACTION, kicking the

guide bar up and back toward the operator.

Pinching the sawchain along the top ofthe

guide bar may push the guide bar rapidly

back toward the operator.

Either of these reactions maycause youto

lose control of the saw which could result

in serious injury.Do not rely exclusively

uponthe safety devices built into yoursaw.

WARNING:

Computed kickback

angle (CKA) listed on your saw and listed in

the CKA table below represents angle of

kickback your bar and chain combinations

will have when tested in accordance with

CSA and ANSI standards. Whenpurchasing

replacement bar and chain, considerations

should be given to the lower CKA values.

Lower CKA values represent safer angles to

the user, higher values indicate more angle

and higher kick energies. Computed angles

represented in the non-activated column in-

dicate total energy and angle associated

without activation of the chain brake during

kickback. Activated angle represents chain

stopping time relative to activation angle of

chain brake and resulting kick angle of saw .

In all cases lower CKA values represent a

safer operating environment for the user .

The following guide bar and chain combina-

tions meet kickback requirements of CSA

Z62.1, Z62.3, & ANSI B175.1 when used on

saws listed in this manual. Use of bar and

chain combinations other than those listed is

not recommended and may not meet the

CKA requirements per standard.

Computed kickback angle (CKA) Table

BAR

P/N

Length

CHAIN P/N

16!

MODEL

530044835 952051481

CKA without chain brake

220 LE

260 LE

18!

530044834 952051480

NOTE:

If this saw is to be used for commer-

cial logging, a chainbrake isrequired and shall

not be removed or otherwise disabled to com-

ply with Federal OSHA Regulations for Com-

mercial Logging.

SAFETY NOTICE:

Exposure to vibrations

through prolonged use of gasoline powered

hand tools could cause blood vessel or nerve

damage in the fingers, hands, and joints of

people prone to circulation disorder s or

abnormal swellings. Prolonged use in cold

weather has been linked to blood vessel

damage in otherw ise healthy people. If

symptoms occur such as numbness, pain,

loss of strength, changein skincolorortexture,

or loss of feeling inthe fingers,hands, or joints,

discontinue the use of this tool and seek

medical attention. An anti-vibr ation system

does not guarantee the avoidance of these

problems. User s who operate power tools on

a continual and regular basis must monitor

closely their physical condition and the

condition of this tool.

SPECIALNOTICE:

Yoursaw isequipped

with a temperature limiting muffler and spark

arresting screen which meets the

requirements of California Codes 4442 and

4443. All U.S. forest land and the states of

California, Idaho, Maine, Minnesota, New

Jersey, Oregon, and Washington require by

law that many internal combustion engines

tobeequipped with aspark arresting screen.

If youoperate achain sawin astate orlocale

where such regulations exist, you arelegally

responsible for maintaining the operating

condition of these parts. Failure to do so is

a violation of the law. Refer to the SERVICE

section for maintenance of the spark

arresting screen.

Failureto follow all SafetyRulesandPrecau-

tions canresult in serious injury. If situations

occur which are not covered in this manual,

use care and good judgement. If you need

assistance, contact your authorized service

dealer or call 1-800--554--6723.

STANDARDS:

Thissawis listedbyUnder-

wr iter’s Laboratories, Inc., and the Canadian

Standards Association in accordance with:

ANSI B175.1-2000 American National

Standard for Powered Tools -- Gasoline

Powered Chain Saw -- Safety Requirements

CSA Z62.1--1995 Chain Saws -- Occupa-

tional Health and Safety

CSA Z62.3--1996 Chain Saw Kickback Oc-

cupational Health and Safety

ASSEMBLY

Protective gloves (not provided) should be

worn during assembly.

ATTACHINGTHEBAR&CHAIN

(If not

already attached)

WARNING:

If received assembled,

repeat all steps to ensure yoursaw isproperly

assembled and all fasteners are secure. Al-

ways wear gloves when handling the chain.

Thechain is sharp and can cutyou even when

it is not moving!

1. Loosen and remove the chain brakenuts

and the chain brake from the saw.

2. Remove the plastic shipping spacer (if

present).

Chain Brake

Nuts

Bar Tool

Location of shipping spacer

3. Turn adjusting screw on bar counter-

clockwise tomovethetensioning rackas

far as it will go toward the front of the bar.

Tensioning Rack

Adjusting

Screw

4. Slide the barbehind clutch drum until bar

stops against clutch drum sprocket.

Mount the Bar

5. Prepar e the chain by checking the proper

direction. Without followingthe illustrationit

is easy toplace thechain on thesaw inthe

wrong dire c tion . Use the illustration of the

chain to determine the proper direction.

CUTTERS MUST FACE IN

DIIRECTION OF ROTATION

Tip of

Bar

Cutters

Depth Gaug

Drive Links

6. Place the chain over and behind the

clutch, fitting the drive links in the clutch

drum sprocket.

Place chain onto the sprocket

7. Fit bottom of drive links between the

teeth in the sprocket in the nose of the

guide bar.

8. Fit chain drive links in to bar groove.

9. Pull the bar forward until the chain is

snug in the groove of the bar. Ensure all

drive links are in the bar groove.

10. Hold guide bar against the saw frame

and install the chain brake.

11. Replace the chain brakenuts andtighten

finger tight. Once the chain istensioned

you will need to tighten chain brake nuts.

CHAIN TENSION

(Including units with

chain already installed)

NOTE:

When adjusting chain tension,

make sure the chain brake nuts are finger

tight only. Attempting to tension the chain

when the chain brake nuts are tight can

cause damage.

Checking the tension:

Use the screwdriver end of the chain adjust-

ment tool (bar tool) to movethe chain around

the bar. If the chain does not rotate, it is too

tight. If tooloose, the chain willsag below the

bar.

Chain Brake Nuts

Chain Adjustment

Tool (Bar Tool)

Adjusting the tension:

Chain tension is very important. Chain

stretches during use. This is especially true

during the first few times you use your saw.

Always check chain tension each time you

use and refuel your saw.

An adjusting screw (located on the guide bar)

is used to adjust the tension of the chain (see

illustr atio n).

1. Turn adjusting screw clockwise until

chain solidly contacts bottom of guide

bar rail.

Adjusting

Screw

Guide bar

2. Using the screwdriver end ofthe bartool,

roll chain around guide bar to ensure all

links are in bar groove.

3. Lift up tip of guide bar to check for sag.

Release tip of guide bar,then turn adjust-

ing screw until sag does not exist.

4. Tighten bar clamp nuts securely with the

bar tool.

Chain Brake

Nuts

5. Use the screwdriver end of the bar tool to

move chain around guide bar.

6. If chain does not rotate, it is too tight.

Slightly loosen bar clamp nuts and loos-

en chain by turning the adjusting screw.

Retighten bar clamp nuts.

7. If chain is too loose, it will sag below the

guide bar. DO NOT operate the saw if

the chain is loose.

WARNING:

If the saw is operated

with a loose chain, the chain could jump off

the guide bar and result in serious injury.

OPERATION

KNOW YOUR SAW

READ THIS INSTRUCTION MANUAL AND SAFETY RULES BEFORE OPERATING YOUR

CHAIN SAW. Compare the illustrations with your unit to familiarize y ourself with the location of

the various controls and adjustments. Save this manual for future reference.

Chain

Adjustment Tool

(Bar Tool)

Primer

Bulb

Fuel Mix Fill Cap

Starter

Housing

Bar Oil Fill Cap

Chain

Front Hand Guard

Front Handle

Starter Rope

ON/STOP

Switch

Muffler

Guide Bar

Chain Brake Nuts

Cylinder Cover

Throttle

Lockout

Rear

Handle

Throttle

Trigger

Choke/

Fast Idle

Lever

Chain

Brake

Chain

Direction

of Travel

Adjusting

Screw

Chain

Catcher

ON/STOP SWITCH

The ON/STOP SWITCH is used to stop the

engine.

THROTTLE TRIGGER

The THROTTLE TRIGGER controls engine

speed.

THROTTLE LOCKOUT

The THR O TTLE LOCKOUT must be press ed

before you can squeeze the throttle trigger.

This feature prevents you from accidentally

squeezing the trigger .

CHOKE/FAST IDLE LEVER

The cho k e and fast idle ar e set by pulling the

CHOKE/FAST IDL E LEVER out fully for cold

or refueled starting. The choke provides addi-

tional fuel to the engine during cold starting.

PRIMER BULB

The PRIMER BULB circulates fuel to the

carburetor to provide quicker starting.

CHAIN BRAKE

The CHAIN BRAKE is a device designed to

stop the chain if kickback occurs. The chain

brake activates automatically in the event of

kickback. The chain brake activates manu-

ally if the front hand guard is pushed forward.

The chain brake is disengaged by pulling the

front hand guard back toward the front han-

dle as far as possible.

CHAIN TENSION

Itisnormalforanewchain tostretch duringfirst

30 minutes of operation. You should check

your chain tension frequently . See CHAIN

TENSION under the ASSEMBLY section.

WARNING:

Muffler is very hot dur-

ing and after use. Donot touch the muffler or

allow combustible material such as dry

grass or fuel to do so.

FUELING & LUBRICATION

WARNING:

Remove fuel cap slow-

ly when refueling.

FUELING ENGINE

This engine is certified to operate on

unleaded gasoline. Before operation,

gasoline must be mixed with a good quality

synthetic 2-cycle air-cooled engine oil

designed to be mixed at a ratio of 40:1.

Poulan/Weed Eater brand synthetic oil is

recommended. A 40:1 ratio is obtained by

mixing 3.2 ounces of oil with 1 gallon of

unleaded gasoline. Includedwith this saw is a

3.2 ounce container of Poulan/Weed Eater

brandsynthetic oil. Pour the entire contentsof

this container into 1 gallon of gasoline to

achieve the proper fuel mixture.

DONOT USE automotive or boat oil. These

oils will cause engine damage. Whenmixing

fuel follow the instructions printed on the

container. Always read and follow the safety

rules listed under HANDLE FUEL WITH

CAUTION.

BAR AND CHAIN LUBRICATION

The bar and chain require continuous lubri-

cation. Lubrication is provided by the auto-

matic oiler system when the oil tank is kept

filled. Lack of oil will quickly ruin the bar and

chain. Too little oil will cause overheating

shown bysmokecoming fromthe chain and/

or discoloration of the bar.

In freezing weather oil will thicken, making it

necessary to thin bar and chain oil with a

small amount (5 to 10%) of #1 Diesel Fuel or

kerosene. Bar and chain oil must be free

flowing for the oil system to pump enough oil

for adequate lubrication.

Genuine Poulan or Poulan PRO

bar and

chain oil is recommended toprotect yourunit

against excessive wear from heat and

friction. Poulan orPoulan PRO

oil resists

high temperature thinning. If Poulan or

Poulan PRO

bar and chain oil is not

available, use a good grade SAE 30 oil.

Never usewaste oil for bar and chainlubri-

cation.

Always stop the engine before removing

the oil cap.

IMPORTANT

Experience indicates that alcohol--blended

fuels (called gasohol or using ethanol or

methanol) can attract moisture which leads

to separation and formation of acids during

storage. Acidic gas can damage the fuel

system of an engine while in storage. To

avoid engine problems, the fuel system

should be emptied before storage for 30

days or longer. Drain the gas tank, start the

engine and let it run until the fuel lines and

carburetor are empty. Use fresh fuel next

season. See STORAGE section for addi-

tional information.

STARTING

WARNING:

The chain must not

move when the engine runs at idle speed. If

the chain moves at idle speed refer to CAR-

BURETOR ADJUSTMENT within this

manual. Avoid contact with the muffler. Ahot

muffler can cause serious burns.

To stop the engine move the ON/STOP

switch to the STOP position.

To start the engine hold the saw firmly on

the ground as illustrated. Make sure the

chain is free to turn without contacting any

object.

Hold saw firmly while pulling starter rop

Use only 15”---18” of rope per pull.

Left hand

on front

handle

Right foot through rear handle

Starter rope handle

IMPORTANTPOINTS TOREMEMBER

When pulling the starter rope, do not use the

full extent of the rope as this can cause the

rope to break. Do not let starter rope snap

back. Holdthe handle and let the roperewind

slowly.

For cold weather starting, start the unit at

FULL CHOKE; allow the engine to warm up

before squeezing the throttle trigger.

NOTE:

Do not cut material with the choke/

fast idle lever at the FULL CHOKE position.

STARTING A COLD ENGINE (or

warm engine after running out of

fuel):

NOTE:

In the following steps, when the

choke/fast idle lever is pulled out to the full

extent, the correct throttle setting forstarting

is set automatically.

1. Move ON/STOP switch to the ON posi-

tion.

2. Pull out choke/fast idle to the full extent.

3. Slowly press primer bulb 6 times.

4. Pull the starter rope quickly with your

right hand 5 times. Then, proceed to the

next step.

NOTE:

If the engine sounds as if it is trying

to start before the 5th pull, stop pulling and

immediately proceed to the next step.

5. Push the choke/fast idle lever in com-

pletely (to the OFF position).

6. Pull the starter rope quickly with your

right hand until the engine starts.

7. Allow the engine to runfor approximately

5 seconds. Then, squeeze and release

throttle trigger to allow engine toreturn to

idle speed.

Primer

Bulb

ON/STOP

Switch

STOP

ON/STOP SWITCH

OFF FULL

CHOKE/FAST IDLE LEVER

Choke/Fast

Idle Lever

(SIDE VIEW)

STARTING A WARM ENGINE:

1. Move ON/STOP switch to the ON posi-

tion.

2. Pull thechoke/fast idlelever out to thefull

extent, then push the lever back in com-

pletely (to the OFF position).

3. Slowly press the primer bulb 6 times.

4. Pull the starter rope quickly with your

right hand until the engine starts.

5. Squeeze and release throttle trigger, al-

lowing engine to idle.

DIFFICULT STARTING (or starting a

flooded engine):

The engine may be flooded with too much

fuel if it has not started after 10 pulls.

Flooded engines can be cleared of excess

fuel by following the warm engine starting

procedure listed above. Insure the ON/

STOP switch is in the ON position.

Starting could require pulling the starter rope

handle many times depending on how badly

theunit isflooded. Ifengine fails to start, refer

to the TROUBLESHOOTING TABLE or call

1-800-554-6723.

CHAIN BRAKE

WARNING:

If the brake band is

worn too thin it may break when the chain

brakeistriggered. With abroken brakeband,

the chain brake will not stop the chain. The

chain brake should be replaced by an autho-

rized service dealer if any part is worn toless

than 0.020

(0.5 mm) thick. Repairs on a

chain brake should be made by an autho-

rized service dealer. Take your unit to the

place of purchase if purchased from a ser-

vicing dealer, or to the nearest authorized

master service dealer.

This saw is equipped with a chain brake.

The brake is designed to stop the chain if

kickback occurs.

The inertia--activated chain brake is

activated if the front hand guard is pushed

forward, either manually (by hand) or

automatically (by sudden movement).

If the brake is already activated, it is

disengaged bypulling thefront hand guard

back toward the front handle as far as

possible.

When cutting with the saw,the chainbrake

must be disengaged.

Disengaged

Engaged

Braking function control

CAUTION:

The chain brake must be

checked several times daily. The engine

must berunning whenperforming thisproce-

dure. This is the only instance when the saw

should be placed on the ground with the en-

gine running.

Place the saw on firm ground. Grip the rear

handle with yourright hand andthe front han-

dle with your left hand. Apply full throttle by

fully depressing the throttle trigger. Activate

the chain brake by turning your left wrist

against the hand guard without releasing

your grip around the front handle. The chain

should stop immediately.

Inertia activating function control

WARNING:

When performing the

following procedure, the engine must be

turned off.

Grip the rear handle with yourright hand and

the front handle with your left hand. Hold the

chain saw approximately 14

(35 cm) above

a stump or other wooden surface. Release

your grip on the front handle and use the

weight of the saw to let the top of the guide

bar fall forward and contact the stump.

When the tip of the bar hits the stump, the

brake should activate.

CUTTING METHODS

IMPORTANT POINTS

Check chain tension before first use and

after 1 minute of operation. See CHAIN

TENSION in the ASSEMBLY section.

Cut wood only. Do not cut metal, plastics,

masonry, non-wood building materials,

etc.

Stop the saw if the chain strikes a foreign

object. Inspect the saw and repair or re-

place parts as necessary.

Keep the chain out of dirt and sand. Even a

small amount of dirt will quickly dull a chain

andthusincre as ethepossib ilityof kickbac k .

Practice cutting a few small logs using the

following techniques to get the “feel” of us-

ing your saw before you begin a major

sawing operation.

Squeeze the throttle trigger and allow

the engine to reach full speed before

cutting.

Begin cutting with the saw frame

against the log.

Keep the engine at full speed the entire

time you are cutting.

Allow thechaintocutforyou. Exertonly

light downward pressure. If you force

the cut, damage tothe bar,chain, oren-

gine can result.

Release the throttle trigger as soon as

the cut is completed, allowing the en-

gine to idle. If you run the saw at full

throttle without acutting load, unneces-

sary wear can occur to the chain, bar,

and engine. It is recommended that

the engine not be operated for lon-

ger than 30 seconds at full throttle.

Toavoid losing control whencut iscom-

plete, donotput pressureonsawatend

of cut.

Stop the engine before setting the saw

down after cutting.

TREE FELLING TECHNIQUES

WARNING:

Check for broken or

dead branches which can fall while cutting

causing serious injury. Donot cutnearbuild-

ings or electrical wires if you do not know the

direction oftree fall, norcut atnight since you

will not be ale to see well, nor during bad

weather such as rain, snow ,or strong winds,

etc.

Carefully planyour sawing operation inad-

vance.

Cleartheworkarea. You needaclear area

all around the tree so you can have secure

footing.

Study the natural conditions that can cause

the tree to fall in a particular direction.

Natural conditions that can cause a tree to

fall in a particular direction include:

The wind direction and speed.

The lean of the tree. The lean of a tree

might not be apparent due to uneven or

sloping terrain. Use aplumb orlevel to de-

termine the direction of tree lean.

Weight and branches on one side.

Surrounding trees and obstacles.

Look for decay and rot. If the trunk is rotted, it

can snap and fall toward the operator. Check

for broken or dead branches which can fall on

you while cutting.

Make sure there is enough room for the treeto

fall. Maintain a distance of

2-1/2

tree lengths

from the nearest person or other objects. En-

gine noise can drown out a war ning call.

Removedirt, stones, loosebark, nails, staples,

and wire from the tree wher e cuts are to be

made.

Plan a clear retreat path to the rear and diag-

onal to the line of fall.

Direction of Fall

Plan a clear retreat path

FELLING LARGE TREES

(6 inches in diameter or larger)

The notch method is used to fell large trees.

Anotch iscut on the side of the tree in thede-

sired direction of fall. After a felling cut is

made on the opposite side of tree, the tree

will tend to fall into the notch.

NOTE:

If the tree has large buttress roots,

remove them before making the notch. If us-

ing saw to remove buttress roots, keep saw

chain from contacting ground to prevent dull-

ing of the chain.

NOTCH CUT AND FELLING THE

TREE

Make notch cut by cutting the top of the

notch first. Cut through

1/3

of the diameter

ofthetree. Nextcomplete the notch bycut-

ting the bottom of the notch. See illustra-

tion. Once the notch is cut remove the

notch of wood from the tree.

Notch

First cut

Second cut

Final (felling) cut here. 2 inches

above center of notch.

Hinge

After removing the cutout of wood, make

the felling cut on the opposite side of the

notch. This is done by making a cut about

two inches higher than the center of the

notch. This will leave enough uncut wood

between the felling cut and the notch to

form a hinge. This hinge will help prevent

the tree from falling in the wrong direction.

Closing of

notch

Hinge holds tree on s tump and helps

control fall

Opening

of felling

cut

NOTE:

Before felling cut is c omplete, use

wedges to open the cut when necessary to

control the direction of fall. Toavoid kickback

and chain damage, use wood or plastic

wedges, but never steel or iron wedges.

Be alert to signs that the tree is ready to fall:

crack ing sounds, widening of the felling cut,

or movement in the upper branches.

As tree starts to fall, stop saw,put it down,

and get away quickly on your planned re-

treat path.

DO NOT cut down a partially fallen tree

with your saw. Beextremely cautious with

partially fallen trees that may be poorly

supported. When a tree doesn’t fall com-

pletely,setthe sawaside and pull down the

tree with a cable winch, block and tackle,

or tractor.

CUTTING A FALLEN TREE

(BUCKING)

Bucking is the term used for cutting a fallen

tree to the desired log size.

WARNING:

Donot stand on the log

being cut. Any portion can roll causing loss

of footing and control. Do not stand downhill

of the log being cut.

IMPORTANT POINTS

Cut only one log at a time.

Cut shattered wood very carefully; sharp

pieces ofwood could beflung toward oper-

ator.

Use a sawhorse to cut small logs. Never

allow another person to hold the log while

cutting and never hold the log with yourleg

or foot.

Do not cut in an area where logs, limbs,

and roots are tangled such as in a blown

down area. Drag the logs into a clear area

before cutting by pulling out exposed and

cleared logs first.

TYPES OF CUTTING USED FOR

BUCKING

WARNING:

If saw becomes

pinched or hung in a log, don’t try to force it

out. Youcan losecontrol ofthe sawresulting

in injury and/or damage to the saw. Stop the

saw,drive awedge ofplastic orwood into the

cut until the saw can be removed easily. Re-

start thesawandcarefully reenter the cut. To

avoid kickback and chain damage, do not

use a metal wedge. Donot attempt to restart

your saw when it is pinched or hung in a log.

Use a wedge to remove pinched saw

Turn saw

OFF

and use a plastic or

wooden wedge t o force cut open.

Overcutting begins on thetop sideof thelog

with the bottom of the saw against the log.

When overcutting use light downward pres-

sure.

Overcutting Undercutting

Undercutting involves cutting on the under-

side of the log with top of sawagainst thelog.

When undercutting use light upward pres-

sure. Hold saw firmly and maintain control.

The saw will tend to push back toward you.

WARNING:

Never turn saw upside

down to undercut. The saw cannot be con-

trolled in this position.

Always make your first cut on the compres-

sion side of the log. Thecompression sideof

the log is where the pressure of the log’s

weight is concentrated.

Second cut

First cut on compression side of log

Second cut

BUCKING WITHOUT A

SUPPORT

Overcut through

1/3

of the diameter of the

log.

Roll the log over and finish with a second

overcut.

Watch for logs with a compression side to

prevent the saw from pinching. See il-

lustrations for cutting logs with acompres-

sion side.

BUCKING USING A LOG OR

SUPPORT STAND

Remember your first cut is always on the

compression side of the log.

(Refer to the illustrations below for your

first and second cut)

Your first cut should extend

1/3

of the

diameter of the log.

Finish with your second cut.

Cut

Usingalogforsupport

Cut

Using a support stand

Cut

LIMBING AND PRUNING

WARNING:

Be alert for and guard

against kickback. Do not allow the moving

chain to contact any other branches or ob-

jects at the nose of the guide bar when limb-

ing orpruning. Allowing suchcontact canre-

sult in serious injury.

WARNING:

Never climb into atree

to limb or prune. Do not stand on ladders,

platforms, a log, or in any position which can

cause you to lose your balance or control of

the saw.

IMPORTANT POINTS

Work slowly, keeping both hands firmly

gripped on the saw . Maintain secure foot-

ing and balance.

Watch out for springpoles. Springpoles

are small size limbs which can catch the

saw chain and whip toward you or pull you

off balance. Use extreme caution when

cutting small size limbs.

Be alert for springback. Watch out for

branches that are bent or under pressure.

Avoid being struck by the branch or the

saw when the tension in the wood fibers is

released.

Keep a clear work area. Frequently clear

branches out of the way to avoid tripping

over them.

LIMBING

Always limbatreeafter itis cutdown. Only

then can limbing be done safely and prop-

erly.

Leave the larger limbs underneath the

felled tree to support the tree as you work.

Start at the base of the felled tree and work

toward the top, cutting branches and

limbs. Remove small limbs with one cut.

Keep the tree between you and the chain.

Cut from the side of the tree opposite the

branch you are cutting.

Remove larger, supporting branches with

thecutting techniques described inBUCK-

ING WITHOUT A SUPPORT.

Always use an overcut to cut small and

freely hanging limbs. Undercutting could

cause limbs to fall and pinch the saw.

PRUNING

WARNING:

Limit pruning to limbs

shoulder height or below. Do not cut if

branches are higher than your shoulder.Get

a professional to do the job.

Make your fist cut

1/3

of the way

through the bottom of the limb.

Next make a 2nd cut all the way

through the lim b. Then cut a third

overcut leaving a 1 to 2 inch collar from

the truck of the tree.

First cut

Second cut

Third cut

Collar

Pruning technique

SERVICE

WARNING:

Disconnect the spark

plug before performing maintenance except

for carburetor adjustments.

We recommend all service and adjustments

not listed in this manual be performed by an

authorized service dealer.

MAINTENANCE SCHEDULE

Check:

Fuel mixture level Before each use....

Bar lubrication Before each use.......

Chain tension Before each use.......

Chain sharpness Before each use....

For damaged parts Before each use..

For loose caps Before each use......

For loose fasteners Before each use...

For loose parts Before each use......

Inspect and Clean:

Bar Before each use................

Complete saw After each use.......

Air filter Every 5 hours*.............

Chain brake Every 5 hours*........

Spark arresting screen

and muffler Every 25 hours*.........

Replace spark plug

Yearly.

Replace fuel filter

Yearly...

* Hours of Operation

AIR FILTER

CAUTION:

Do not clean filter in gasoline

or other flammable solvent to avoid creating

a fire hazard or producing harmful evapora-

tive emissions.

Cleaning the air filter:

A dirty air filter decreases engine perform-

ance and increases fuel consumption and

harmful emissions. Always clean after every

5 hours of operation.

1. Loosen 3 screws on cylinder cover.

2. Remove cylinder cover .

3. Remove air filter.

4. Clean the airfilter using hot soapy water.

Rinse with clean coolwater. Air drycom-

pletely before reinstalling.

5. Lightly oil air filter before installing to im-

prove the efficiency of air filter. Use

2 --cycle engine oil or motor oil (SAE 30).

Squeeze excess oil from filter.

6. Reinstall air filter.

7. Reinstall cylinder cover and 3 screws.

TIghten securely.

Air Filter

Cylinder

Cover

Screws

Cylinder

Cover

INSPECT MUFFLER AND SPARK

ARRESTING SCREEN

WARNING:

The muffler on this

product contains chemicals known to the

State of California to cause cancer.

As the unit is used, carbon deposits build up

on the muffler and spark arresting screen,

and must be removed to avoid creating a fire

hazard or affecting engine performance.

Replace the spark arresting screen if breaks

occur.

CLEANING THE SPARK ARREST-

ING SCREEN

Cleaning is required every 25 hours of op-

eration or annually, whichever comes first.

Muffler

Gasket

Muffler

Bolts

Muffler

Locknut

Outlet

Guide

Bolt Cover

Backplate

1. Loosen and remove the locknut from the

bolt cover.

2. Remove the bolt cover .

3. Loosen and remove the 2 muffler bolts.

Remove the muffler, muffler gasket, out-

let guide and backplate. Notice the ori-

entation of these parts for reassembling.

4. Locate the 2 outlet cover screws on the

muffler. Loosen and remove both

screws.

5. Remove the outlet cover.

BACK VIEW OF

MUFFLER

Muffler

Spark Arresting

Screen

Outlet Cover

Screws

6. Remove spark arresting screen.

7. Clean the spark arresting screen with a

wirebrush.Replacescreenifanywiresare

broken or screen is blocked aftercleaning.

8. Reinstall spark arresting screen.

9. Reinstall outlet cover and 2 screws. En-

sure outlet coverand both screws arere-

installed correctly (see illustrations) to

prevent damage to the saw. The ex-

haust outlet must face the chain brake

(bar side) of the saw.

Exhaust Outlet must face chain

brake (bar side) of chain saw

Outlet Cover

Exhaust

Outlet

10. Inspect the muffler gasket and replace if

damaged.

11. Reinstall backplate, outlet guide, muffler

gasket, and muffler using muffler bolts.

Tighten until secure.

12. Reinstall bolt cover and locknut. Tighten

securely.

CARBURETOR ADJUSTMENT

WARNING:

The chain will be mov-

ing during most of this procedure. Wearyour

protective equipment and observe all safety

precautions. The chain must notmove at idle

speed.

The carburetor has been carefully set at the

factory. Adjustments may be necessary if

you notice any of the following conditions:

Chain moves at idle. See IDLE SPEED--T

adjusting procedure.

Saw will not idle. See IDLE SPEED--T ad-

justing procedure.

Idle Speed--T

Allow engine to idle. If the chain moves, idle

istoo fast. If the engine stalls, idle is tooslow.

Adjust speed until engine runs without chain

movement (idle too fast) or s talling (idle too

slow). The idle speed screw is located inthe

area above the primer bulb and is labeled T.

Turn idle speed screw (T) clockwise to in-

crease engine speed.

Turn idle speed screw (T) counterclock-

wise to decrease engine speed.

If you require further assistance or are unsure

about performing this procedure, contact your

authorized service dealer or call

1--800--554--6723.

BAR MAINTENANCE

If your saw cuts to one side, has to be forced

through the cut, or been run with an improper

amount of bar lubrication it may be necessary

to service your bar . A worn bar will damage

your chain and make cutting difficult.

After each use, ensure ON/STO P switch is in

theST OPposition,thenclean all sawdust from

the guide bar and sprocket hole.

To maintain guide bar:

Move ON/STOP switch to the STO P posi-

tion.

Loosen and remove chain brake nuts and

chain brake. Remove bar and chain from

saw.

Cleanthe oil holes and bargroove aftereach

5 hours of operation.

Remove Sawdust From

Guide Bar Groove

Oil Holes

Burringof guide bar rails isa normalprocess

of rail wear. Remove these burrs with a flat

file.

When rail top is uneven, use a flat file to re-

store square edges and sides.

Correct GrooveWorn Groove

File Rail Edges

and Sides

Square

Replace guide bar when the groove is worn,

the guide barisbent or cracked,or whenexce-

ss heating or burr ing of the rails occurs. If re-

placement is necessary, use onlythe guidebar

specified for your saw in the repair parts list or

on the decal located on the chain saw.

CHAIN SHARPENING

Chain sharpening is a complicated task that

requires special tools. We recommended

you refer chain sharpening to a professional

chain sharpener.

IGNITION TIMING

Ignition timing is fixed and nonadjustable.

SPARK PLUG

The spark plug should be replaced each

year to ensure the engine starts easier and

runs better.

1. Loosen 3 screws on cylinder cover.

2. Remove the cylinder cover.

3. Pull off the spark plug boot.

4. Rem ove spark plug from cylinder and dis-

card.

5. Replace with Champion RCJ--7Y spark

plug and tighten securely with a 3/4 inch

socket wrench. Spark plug gap should

be 0.025 inches.

6. Reinstall the spark plug boot.

7. Reinstall the cylinder cover and 3 screws.

Tighten securely.

Screws

Spark

Plug Boot

Spark

Plug

Cylinder

Cover

STORAGE

WARNING:

Stop engine and allow

to cool, and secure the unit before storing or

transporting in a vehicle. Store unit and fuel

in an area where fuel vapors cannot reach

sparks or open flames from water heaters,

electric motors or switches, furnaces, etc.

Store unitwith all guards inplace. Position so

that any sharp object cannot accidentally

cause injury to passersby. Store the unit out

of reach of children.

Before storing, drain all fuel from the unit.

Start engine and allow to run until it stops.

Clean the unit before storing. Pay particu-

lar attention to the air intake area, keeping

it free of debris. Use a mild detergent and

sponge to clean the plastic surfaces.

Donotstore the unit orfuel ina closed area

where fuel vapors can reach sparks or an

openflamefrom hot water heaters, electric

motors or switches, furnaces, etc.

Store in a dry area out of the reach of chil-

dren.

CAUTION:

It is important to prevent gum

deposits from forming in essential fuel system

parts such as the carburetor, fuel filter, fuel

hose, or fuel tank during storage. Alcohol

blended fuels (called gasohol or using ethanol

or methanol) can attract moisture which leads

to fuel mixture separation and formation of

acids during storage. Acidic gas can damage

the engine.

NEED ASSISTANCE?

Call 1--800--554--6723.

NEED SERVICE PART?

Contact your authorized service dealer.

TROUBLE CAUSE REMEDY

Engine will not

start or will run

only a few

seconds after

starting.

1. Ignition switch off.

2. Engine flooded.

3. Fuel tank empty.

4. Spark plug not firing.

5. Fuel not reaching

carburetor.

1. Move ignition switch to ON.

2. See “Difficult Starting” in

Operation Section.

3. Fill tank with correct fuel mixture.

4. Install new spark plug.

5. Check for dirty fuel filter; replace.

Check for kinked or split fuel line;

repair or replace.

Engine will

not idle

properly.

1. Idle speed requires

adjustment.

2. Carburetor requires

adjustment.

1. See “Carburetor Adjustment” in the

Service and Adjustments Section.

2. Contact an authorized service dealer.

1. Air filter dirty.

2. Spark plug fouled.

3. Chain brake engaged.

4. Carburetor requires

adjustment.

Engine will not

accelerate,

lacks power,

or dies under

a load.

1. Clean or replace air filter.

2. Clean or replace plug and regap.

3. Disengage chain brake.

4. Contact an authorized service dealer.

Engine

smokes

excessively .

1. Too much oil mixed with

gasoline.

1. Empty fuel tank and refill with

correct fuel mixture.

WARNING:

Always stop unit and disconnect spark plug before performing all of

the recommended remedies below except remedies that require operation of the unit.

TROUBLESHOOTING TABLE

Chain moves

at idle speed.

1. Idle speed requires

adjustment.

2. Clutch requires repair.

1. See “Carburetor Adjustment” in the

Service and Adjustments Section.

2. Contact an authorized service dealer.

LIMITED WARRANTY

ELECTROLUX HOME PRODUCTS, INC.,

warrants to the original purchaser that each

new Poulan PRO

brand gasoline chain

saw is free from defects in material and

workmanship andagrees torepair orreplace

under this warranty any defective gasoline

chain saw as follows from the original date of

purchase.

2 YEARS -- Parts and Labor,when used for

Household purposes.

60 DAYS -- Parts and Labor, when used for

Commercial, Professional, or Income Pro-

ducing purposes.

30 DAYS -- Parts andLabor, ifused forrental

purposes.

This warranty is not transferable and does

not cover damage or liability caused by im-

proper handling, improper maintenance, or

the use of accessories and/or attachments

not specifically recommended by ELEC-

TROLUX HOME PRODUCTS, INC., forthis

chain saw. Additionally, this warranty does

not cover damage caused by improper han-

dling, improper maintenance, or if the saw is

altered inany waywhich inourjudgement af-

fects itscondition oroperation. Thiswarranty

does not cover tune--up, spark plugs, filters,

starterropes, starter springs, chain sharpen-

ing, bars, chains, and other parts which wear

and require replacement with reasonable

use during the warranty period. This warran-

ty does not cover predelivery set--up, instal-

lation of guide bar and chain, and normal ad-

justments explained in the instruction

manual such as carburetor adjustments and

chain tension adjustments. This warranty

does not cover transportation costs.

THIS WARRANT Y GIVES YOU SPECIFIC

LEGA L RIGHTS, AND YOU MAY HAVE

OTHER RIGHTS WHICH V AR Y FROM

STATE TO STATE.

NO CLAIMS FOR CONSEQUENTIAL OR

OTHER DAMAGES WILL BE ALLO W ED,

AND TH ERE ARE NO OTHER EXPRESS

W ARRAN TIESEXCEPTTHOSEEXPRESS-

L Y STIPULATED HEREIN.

SOM E STATES DO NO T ALLOW LIMITA-

TIONS ON HOW LONG AN IMPLIED WAR-

RANTY LASTS OR THE EXCLUSION OR

LIMIT A TIONS OF INCIDENTAL OR CONSE-

QUENTIAL DAMAG ES, SO THE ABO VE

LIMIT A TIONS OR EXCLUSION MAY NOT

APPLY TO YOU.

The policy of ELECTROLUX HOME PRO-

DUCTS, INC., is to continuously improve its

products. Therefore, ELECTROLUX HOME

PRODUCTS, INC., reserves the right to

change, modify, or discontinue models, de-

signs, specifications, and accessories of all

products at any time without notice orobliga-

tion to any purchaser.

U.S. EPA/CALIFORNIA/ENVIRONMENT CANADA

EMISSION CONTROL WARRANTY STATEMENT

YOUR W ARRANTY RIGHTS ANDOBLIGA-

TIONS: The U.S. Environmental Protection

Agency, California Air Resources Board, Envi-

ronment Canada and ELECTR O LU X HOME

PRODUCTS, INC., are pleased to explain the

emissions control system warranty on your

year2002--2004small off--road engine. In Cali-

fornia, all new small off--road engines must be

designed, built, and equipped to meet the

State’s stringent anti--smog standards. ELEC-

TROLUX HOME PRODUCTS, INC., must

warr ant the emission control system on your

small off--road engine for the periods of time

listedbelowprovidedtherehasbeen noabuse,

neglect, orimpr opermaintenanceof yoursmall

off--road engine engine. Your emission control

system includes parts such as the carburetor

and the ignition system. Where a warr antable

condition exists, ELECTRO LU X HOME

PRODUCTS, INC., will repair your small off--

road engine engine at no cost to you. Ex-

penses covered under warr anty include diag-

nosis, parts and labor. MANUF ACTURER’S

W ARRANTY COVERAGE: If any emissions

related part on your engine (as listed under

Emissions Control W arr anty Parts List) is de-

fective ora defect inthe materials orworkman-

ship of the engine causesthe failure of suchan

emission related part, the part will be repaired

or replaced by ELECTROLU X HOMEPROD-

UCTS, INC. OWNER’S WARRANTY RE-

SPONSIBILITIES: As the small off--road en-

gine engine owner, you are responsible for the

performance of the required maintenance

listed in your instruction manual. ELECTRO-

LUX HOME PRODUCTS, INC., recommends

that you retain all receipts covering mainte-

nance on your small off--road engine, but

ELECTROLUX HOME PRODUCTS, INC.,

cannot deny warranty solely for the lack of re-

ceipts or for your failure to ensure the perfor-

mance of all scheduled maintenance. As the

small off--road engine engine owner, you

should be aware that ELECTR O LU X HOME

PRODUCTS, INC., may deny you warranty

coverage if your small off--road engine engine

or a part of it has failed due to abuse, neglect,

improper maintenance, unapproved modifica-

tions, ortheuse of parts not made orapproved

by the original equipment manufacturer. You

are responsible for presenting your small off--

road engine to an ELECTROLU X HOME

PRODUCTS, INC.,authorized repair centeras

soon as a problem exists. Warr anty repairs

should be completed in a reasonable amount

of time,not to exceed 30 days. If you haveany

questions regarding your warranty rights and

responsibilities, you should contact your near-

est authorized service center or call ELEC-

TROLUX HOME PRODUCTS, INC., at

1--800--554--6723. W ARRANTY COM-

MENCEMENT DA TE: The warr anty period

begins on the date the small off--road engine is

purchased. LENGTH OF COVERAGE: This

war rantyshall befor a period of two yearsfrom

the initial date of purchase. WHAT IS COV-

ERED: REPAIR OR REPLACEMENT OF

P ARTS. Repair or replacement of any war-

ranted part will be performed at no charge to

the owner at an approved ELECTRO LU X

HOME PRODUCTS, INC., servicing center . If

you have any questions regarding your war-

ranty rights and responsibilities, you should

contact your nearestauthorized servicecenter

or call ELECTROLUX HOME PRODUCTS,

INC., at 1--800--554--6723. W ARRANTY PE-

RIOD: Any war r anted part which is not sched-

uled for replacement as requiredmaintenance,

or which is scheduled only for regular inspec-

tion to the effect of “repair orreplace asneces-

sary” shall be warranted for 2 years. Any war-

rantedpartwhich is scheduledforreplacement

asrequiredmaintenance shallbe warrantedfor

the period of time up to the first scheduled re-

placement point for that part. DIAGNOSIS:

The owner shall not be charged for diagnostic

labor which leads to the determination that a

warr anted part is defective if the diagnostic

wor k is performed at an approved ELECTRO-

LUX HOME PRODUCTS, INC., servicing

center. CONSEQUENTIAL DAMAGES:

ELECTROLUX HOME PRODUCTS, INC.,

may be liable for damages to other engine

components caused by the failure of a war-

ranted part still under warr anty. WHAT IS NOT

COVERED: All failures caused by abuse, ne-

glect, or improper maintenance are not cov-

ered. ADD--ON OR MODIFIED P ARTS: The

use of add--on or modified parts can be

grounds for disallowing a warranty claim.

ELECTROLUX HOME PRODUCTS, INC., is

not liable to cover failures of warr anted parts

causedby the useof add--on ormodifiedparts.

HOW TO FILE A CLAIM: If you have any

questions regarding your warranty rights and

responsibilities, you should contact your near-

est authorized service center or call ELEC-

TROLUX HOME PRODUCTS, INC., at

1--800--554--6723. WHERE TO GET WAR-

RANTY SER VICE: Warr anty services or re-

pairs shall be provided at all ELECTROLUX

HOME PRODUCTS, INC., service centers.

Call: 1--800--554--6723. MAINTENANCE, RE-

PLACEMENT AND REPAIR OF EMISSION

RELA TED PARTS: Any ELECTROLU X

HOME PRODUCTS, INC., approved replace-

ment part used in the performance of any war-

ranty maintenance or repair on emission re-

lated parts will be provided without charge to

the owner if the part is under warranty. EMIS-

SION CONTROL WARRANTY PARTS LIST:

Carbur etor, Ignition System: Spark Plug (cov-

ered up to maintenance schedule), Ignition

Module, Muf fler including catalyst. MAINTE-

NANCE ST ATEMENT:Theownerisresponsi-

ble for the performance of all required main-

tenance as defined inthe instruction manual.

The information on the product label indicates which standard your engine is certified.

Example: (Year) EPA Phase 1 or Phase 2 and/or CALIFORNIA.

This engine is certified to be emissions compliant for the following use:

Moderate (50 hours)

Intermediate (125 hours)

Extended (300 hours)

Poulan Pro 220 LE User manual

Brand: Poulan Pro

Model: 220 LE

Category: Power chainsaws

Type: User manual

Download PDF

report

Poulan Pro 220 LE User manual

Poulan Pro 220 LE User manual

Related papers

Other documents