EMP-S4

Epson EMP-S4, PowerLite S4 User manual

  • Hello! I am an AI chatbot trained to assist you with the Epson EMP-S4 User manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
User’s Guide
Epson PowerLite S4
®
2
Meaning of Symbols
Meaning of Symbols
Copyright Notice
All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying,
recording, or otherwise, without the prior written permission of Seiko Epson Corporation. The information contained herein is designed only for use with this Epson product.
Epson is not responsible for any use of this information as applied to other products.
Neither Seiko Epson Corporation nor its affiliates shall be liable to the purchaser of this product or third parties for damages, losses, costs, or expenses incurred by purchaser or
third parties as a result of: accident, misuse, or abuse of this product or unauthorized modifications, repairs, or alterations to this product, or (excluding the U.S.) failure to strictly
comply with Seiko Epson Corporation’s operating and maintenance instructions.
Seiko Epson Corporation shall not be liable for any damages or problems arising from the use of any options or any consumable products other than those designated as
Original Epson Products or Epson Approved Products by Seiko Epson Corporation.
Trademarks
Epson is a registered trademark of Seiko Epson Corporation.
Epson Connection, Epson Store, and Extra Care are service marks; and PrivateLine, Presenters Club, and PowerLite are registered trademarks of Epson America, Inc.
Pixelworks, DNX, and the DNX logo are trademarks of Pixelworks, Inc.
General Notice: Other product names used herein are for identification purposes only and may be trademarks of their respective owners. Epson disclaims any and all rights in
those marks.
Copyright © 2006 by Epson America, Inc. 2/06
c
Indicates the possibility that people may be injured or the equipment may be damaged if the instructions are not
followed.
p
Indicates tips or additional helpful information.
3
Contents
Meaning of Symbols 2
Copyright Notice 2
Trademarks 2
Projector Features
Setting Up the Projector 6
Part Names and Functions 7
Front/Top 7
Control Panel 8
Rear 9
Base 10
Remote Control 11
Adjusting and Changing the Image
Adjusting the Image Quality 12
Adjusting Computer Images and RGB Video Images 12
Selecting the Projection Quality (Color Mode) 14
Adjusting the Projection Position (Image Shift) 16
Adjusting the Volume 17
Selecting the Image Source 17
Automatically Detecting the Source (Source Search) 17
Selecting the Source from the Remote Control 18
Additional Projector Functions
Functions for Enhancing Projection 19
Muting the Image and Sound (A/V Mute) 19
Freezing the Image 20
Changing the Aspect Ratio 20
Displaying the Pointer 21
Enlarging Part of the Image (E-Zoom) 21
Using the Remote Control as a Mouse 22
Security Functions 24
Preventing theft (Password Protect) 24
Using the Operation Lock 26
Saving a User's Logo 28
Displaying Projected Images on an External Monitor 30
Configuration Menus
Using the Menu System 31
"Image" Menu 32
"Signal" Menu 33
"Settings" Menu 34
"Extended" Menu 35
"Info" Menu 37
"Reset" Menu 38
4
Maintenance
Cleaning 39
Cleaning the Projector 39
Cleaning the Lens 39
Cleaning the Air Filters and Air Intake Vent 39
Replacing Consumables 40
Replacing the Batteries 40
Lamp Replacement Period 40
Replacing the Lamp 41
Resetting the Lamp Operating Time 43
Replacing the Air Filter 44
Troubleshooting
Using the Help Menu 45
Problem Solving 47
Reading the Indicators 47
When the Indicators Provide No Help 50
Where To Get Help 57
Internet Support 57
Speak to a Support Representative 57
Purchase Supplies and Accessories 57
Appendix
Optional Accessories and Consumables 58
Screen Size and Projection Distance 59
Glossary 60
List of ESC/VP21 Commands 62
List of Supported Monitor Displays 63
Specifications 64
Dimensions 66
Declaration of Conformity 67
FCC Compliance Statement 67
Important Safety Instructions 68
5
Projector Features
Direct Power On and Instant Off
Use the Direct Power On function to turn the projector on simply by plugging
the power cable into an electrical outlet. See page 36
.
When you’re done using the projector, just turn it off, unplug it, and place it in
the carrying case. The projector’s Instant Off design means you don’t have to
let it cool down first.
Ease of Use
Lens cover
Temporarily stop projection by closing the lens
cover.
Single foot design
Make height adjustments quickly with one hand.
Easy to use, big button control panel
Automatic source search
Press the Source Search button to automatically detect and display the
connected picture signal.
On-screen Help
Quickly answer questions about common projection problems. See page 45
.
Color Modes
Project movies, photos, presentations, and games in the optimum color tone
by choosing the most suitable mode for your surroundings. See page 14
.
Security Function
Set up a password to restrict use of the projector. See page 24.
Disable all control panel buttons except for the Power button to prevent
your settings being changed when the projector is used in a public place.
See page 26
.
6
Setting Up the Projector
Setting Up the Projector
The projector supports the following four projection methods, allowing you to
choose the best method for displaying your images.
c
For ceiling mount installation (suspending from the ceiling), a special
installation procedure is required. Failure to install correctly may
result in injury or damage if the projector falls.
Do not turn the projector on its side during projection, or malfunctions
may occur.
To prolong the life of the projector, turn it off when not in use.
Front projection (Front projection)
Rear projection using a translucent screen (Rear projection)
p
The optional ceiling mount is required when installing the projector on
a ceiling. See page 58
.
When using ceiling projection or projection using a translucent
screen, set the "Projection" command in the "Extended" menu to
match the installation method. See page 35
.
Front/ceiling projection (Front/Ceiling projection)
Rear/ceiling projection using a translucent screen
(Rear/Ceiling projection)
7
Part Names and Functions
Part Names and Functions
Front/Top
Lamp cover
Open this cover when replacing the
projector's lamp.
Control panel
Remote control light-receiving area
Receives signals from the remote control.
Front adjustable foot
Raises the projector to adjust the projection
angle.
Lens cover
Slide shut when not using the projector to
protect the lens.
If you close it while projecting, the image and
sound are termporarily stopped.
Focus ring
Adjusts the image focus.
Foot release lever
Extends the front foot.
Air exhaust vent
Security lock
8
Part Names and Functions
Control Panel
[Power] button
Turns the projector power on or off.
[Help] button
Displays and closes the help, which shows
solutions if a problem occurs.
[Menu] button
Displays and closes the configuration menu.
[Esc] button
Stops the current function.
Displays the previous screen
or menu while viewing a
configuration menu.
[Source Search] button
The input source is automatically searched for in the
following order, and the input image from the connected
equipment is projected.
Computer port
S-Video port
Video port
[Enter] button
Automatically adjusts analog RGB images from computers
and RGB video images to the optimum images.
If a configuration menu or help screen is displayed, it
accepts and enters the current selection.
[ ] [ ] button
Press to correct keystone distortion.
If a configuration menu or help screen is
displayed, it selects menu items and
setting values.
[Wide] [Tele] button
Adjusts the image size. If a configuration menu or help
screen is displayed, it selects menu items and setting
values.
LED indicators
The color of the
indicators and whether
they are flashing or lit
shows the state of this
projector.
9
Part Names and Functions
Rear
Remote control light-receiving area
Receives signals from the remote control.
Power inlet
Connects to the power cable.
Computer port
Inputs analog RGB video signals from a
computer and RGB video signals and
component video signals from other video
sources.
Video port
Inputs component
video signals to the
projector from other
video sources.
S-Video port
Inputs S-video signals
to the projector from
other video sources.
USB port
Connects the projector to a computer via the
USB cable when using the wireless mouse
function.
Computer images cannot be projected by using
the USB cable to connect the computer.
Monitor Out port
Outputs the projected computer's analog RGB
signals or RGB video signals to an external
monitor from the source that is connected to
the Computer port. This feature is not available
for video equipment signals.
Speaker
Rear adjustable foot
Lets you level the image.
Audio input
Input audio signals from connected external
equipment.
When you are connecting two or more pieces of
external equipment that use the same input port,
you need to disconnect one before connecting the
other, or use an audio selector.
10
Part Names and Functions
Base
Air filter (air intake vent)
This prevents dust and other foreign particles
from getting inside the projector when air is
drawn in. It should be cleaned and replaced
periodically.
Suspension bracket fixing points (3 points)
Attach the optional ceiling mount here when suspending the projector from a ceiling.
Front adjustable footFoot adjust lever
Air intake vent
Clean the air intake vent
periodically.
11
Part Names and Functions
Remote Control
[A/V Mute] button (see page 19)
[E-Zoom] button ( ) ( ) (see page 21
)
[Enter] and [Esc] button (see page 22)
[Auto] button (see p.12)
[Menu] button (see page 31
)
[Power] button (see Quick Setup sheet)
[Color Mode] button (see page 14
)
[ ] button (see page 22
)
[Freeze] button (see page 20)
[Page down] [Page up] buttons (see page 22
)
[Computer] button (see page 18)
[S-Video] button (see page 18
)
[Video] button (see page 18
)
[Resize] button (see page 20
)
[Pointer] button (see p.21)
[Help] button (see page 45
)
[Volume] buttons (see page 17
)
[Num] button and numeric buttons (see page 24
)
[Search] button (see page 17)
12
Adjusting the Image Quality
Adjusting and Changing the Image
Adjusting the Image Quality
Adjusting Computer Images and RGB Video Images
Automatic Setup
Automatic setup detects analog RGB signals coming from a connected
computer, and automatically adjusts these signals so that the optimum
images can be obtained.
Automatic setup involves adjustment of Tracking, Position, and Sync
(synchronization).
If "Auto Setup" in the "Signal" menu is set to "Off", automatic setup is not
carried out. In this case, press the [Auto] button on the remote control or the
[Enter] button on the projector's control panel to make the adjustment while
computer or RGB video images are being projected.
Adjusting the Tracking
If vertical stripes appear in the projected computer
or RGB video images, and this cannot be fixed using
automatic setup, you will need to adjust the Tracking
manually using the following procedure.
1 Select "Signal" from the configuration
menu, and then select "Tracking".
Check the buttons you can use and the operations they perform in the
guide at the bottom of the screen.
Using the remote control
Using the control panel
p
If you try to make the adjustment while other functions such as E-zoom or
Freeze are in use, these functions are canceled and then the adjustment is
made.
Sometimes the signals may not be adjusted correctly depending on the type
of computer or RGB video signals being input. In such cases, use the
configuration menu commands to adjust the tracking and sync settings
manually. See page 33.
Using the remote control
Using the control panel
13
Adjusting the Image Quality
2 Adjust the tracking until the vertical stripes disappear from the
image.
The tracking value increases or decreases each time a button is
pressed.
3 Press the [Menu] button to exit the configuration menu.
Adjusting the Sync
If flickering, fuzziness or interference appear in
computer or RGB video images, and this cannot be
fixed using automatic setup, you will need to adjust
the Sync (synchronization) manually using the
following procedure.
1 Select "Signal" from the configuration
menu, and then select "Sync.".
Check the buttons you can use and the operations they perform in the
guide at the bottom of the screen.
2 Adjust the synchronization until the horizontal noise disappears
from the image.
p
The image will flash when continuous tracking adjustment is carried out,
but this is normal.
Using the remote control
Using the control panel
Using the remote control
Using the control panel
14
Adjusting the Image Quality
The sync value increases or decreases each time a button is pressed.
3 Press the [Menu] button to exit the configuration menu.
Selecting the Projection Quality (Color Mode)
The following seven preset color modes are
available for use depending on the characteristics of
the images that are being projected. You can easily
obtain the optimum image quality simply by
selecting the color mode that corresponds to the
projected images. The brightness of the images will
vary depending on which color mode is selected.
p
If you adjust the sync without adjusting the tracking first, it will not be
possible to get the best adjustment results. Incorrect tracking adjustment
may not be noticeable with some types of images. However, images with
lots of lines and shading will tend to show incorrect tracking adjustments
more clearly, so check the tracking adjustment first.
Flickering and fuzziness may also occur when the brightness, contrast,
sharpness, zoom, and keystone correction settings are adjusted.
Using the remote control
Using the control panel
Mode Application
Photo (When computer and RGB video images are being input)
The images are vivid and contrast is increased. Ideal for projecting
still pictures, such as photos, in a bright room.
Sports (When component video, S-video, or composite video images are
being input)
The images are vivid and brought to life. Ideal for watching TV
programs and so on in a bright room.
Presentation Ideal for giving presentations in a bright room
Theatre Gives images a natural tone. Ideal for watching films in a dark
room.
Game Excels at emphasizing dark gradations. Ideal for playing video
games in a bright room.
sRGB Ideal for images that conform to the sRGB color standard
Blackboard Even if you are projecting onto a blackboard (green board), this
setting gives your images a natural tint, just like when projecting
onto a screen
15
Adjusting the Image Quality
Each time you press the button, the color modes change in the following
order.
The current setting appears in the top-right corner of the screen each time the
color mode is changed. While the color mode name is displayed on the
screen, it does not change to the next color mode setting unless you press the
button.
p
The color mode can also be set using the "Color Mode" command in the
"Image" menu. See page 32.
16
Adjusting the Projection Position (Image Shift)
Adjusting the Projection Position (Image Shift)
When you cannot setup this projector directly in front of the screen, the
projection position can be finely tuned without moving this projector.
1 Using the button on the projector, perform zoom adjustment or
keystone correction. See the Quick Setup sheet.
The Image Shift adjustment screen is displayed after you finish
making adjustments.
2 Adjust projection position.
3 Press the [Esc] button to close the adjustment screen.
The screen closes automatically if no operations are performed for
about 10 seconds.
p
The projection position cannot be adjusted when zoom is set to
maximum "wide".
Even if you turn the power supply off, the "Image Shift" settings you
make are kept. When either the projector position or the angle of the
projector is changed, you can readjust or perform the following
operations.
You can also make adjustments from the configuration menu. See page
33.
Using the Remote Control Using the Control Panel
Press and hold down the
[Wide] and [Tele] buttons
for more than one second.
Control Panel
17
Adjusting the Volume
Adjusting the Volume
The volume of the projector's built-in speaker can be adjusted as follows.
When the button is pressed to the [ ] side, the volume increases, and when
it is pressed to the [ ] side, the volume decreases.
The volume gauge appears on the screen when the volume is being adjusted.
Selecting the Image Source
The image source is the projector port to which your video equipment is
connected. You can select the image source automatically, using Source
Search as described below. Or you can select a source yourself as described
on page 18
.
Automatically Detecting the Source (Source Search)
Source Search automatically detects the picture signal from connected
equipment and projects the image.
1 Turn on your computer or video equipment. If you are viewing a
tape or DVD, start playback.
2 Press the Source Search button.
p
If the value displayed in the gauge on the screen stops changing when the
volume is being adjusted, it indicates that the limit for volume adjustment
has been reached.
The volume can also be adjusted using the configuration menu. See page
34.
Remote control
Using the Remote Control Using the Control Panel
18
Selecting the Image Source
3 The projector searches for an active source and displays the
image.
Unused sources are skipped, as shown below. When two or more
pieces of equipment are connected, press the [Source Search] button
repeatedly to select the desired source.
Selecting the Source from the Remote Control
You can use the remote control to select a specific image source.
p
You see this screen if no picture signal is available. You can use the screen
to choose the input source.
Computer S-Video Video
Skip
Changes to the image
from the Computer port.
Changes to the image
from the S-Video port.
Changes to the image
from the Video port.
Remote Control
19
Functions for Enhancing Projection
Additional Projector Functions
This chapter explains functions used when giving presentations and for using
the projector’s security functions.
Functions for Enhancing Projection
Muting the Image and Sound (A/V Mute)
For example, this can be used if you want to pause the projection for a
moment and focus the audience’s attention on what you are saying. Or if you
are making a computer presentation and you do not want to show details,
such as selecting different files.
You can temporarily turn off the image and sound in two ways:
When you close the lens cover, projection and sound are turned off. Open
the lens cover to restore projection and sound.
When you press the A/V Mute button on the remote control, projection and
sound are turned off. If you saved a user’s logo (see page 28
), you can set
it to display when you press the A/V Mute button (see page 35
). Press the
A/V Mute button again to restore projection and sound.
Using the remote control
Pressing the [A/V Mute] button
stops projection and sound.
Closing the lens cover stops
projection and sound.
Using the projector
p
If you’re watching a moving picture, the video source continues to play
while the screen is dark. You should pause the video if you wish to resume
playback where you stopped it.
The screen display in A/V mute can be chosen from black, blue, or a logo
by using "Extended" -"Display" - "A/V Mute" in the configuration menu.
20
Functions for Enhancing Projection
Freezing the Image
The source image continues to project even when the screen is frozen. You
can still perform operations such as changing files, without projecting any
images.
You can turn this function on or off by pressing the [Freeze] button.
Changing the Aspect Ratio
This function changes the aspect ratio of images from 4:3 to 16:9 when
component video, S-video, or composite video images are being projected.
Images which have been recorded in digital video or onto DVDs can be
viewed in 16:9 wide-screen format.
The display is changed whenever you press the button.
p
Sound does not stop.
Even though the image on the screen is frozen, the image source
continues to project, and so it is not possible to resume projection from
the point where it was paused.
Pressing the [Freeze] button also clears configuration menu displays
and help messages.
The freeze function still works while the E-Zoom function is being used.
Remote control
p
You can also make this setting using the "Resize" command in the
"Signal" menu.
When images in Squeeze
Mode are projected at 16:9
When images in Squeeze
Mode are projected at 4:3
Remote control
/