Pro-Form GT 120 User manual

GT 120
Pro-Form
Brand
Pro-Form
Model
GT 120
Category
Fitness, gymnastics & weight training
Type
User manual
USER'S MANUAL
CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. Keep this manual
for future reference.
Serial
Number
Decal
QUESTIONS?
As a manufacturer, we are com-
mitted to providing complete
customer satisfaction. If you
have questions, or if there are
missing parts, we will guarantee
complete satisfaction through
direct assistance from our factory.
TO AVOID DELAYS, PLEASE
CALL DIRECT TO OUR TOLL-
FREE CUSTOMER HOT LINE.
The trained technicians on our
customer hot line will provide
immediate assistance, free of
charge to you.
CUSTOMER HOT LINE:
1-877-994-4999
Mon.–Fri., 6 a.m.–6 p.m. MST
Model No. RBEX69740
Serial No.
Visit our website at
www.reebokhomefitness.com
new products, prizes,
fitness tips, and much more!
V
Patent Pending
2
I
MPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
A
SSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
EXERCISE CYCLE OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
MAINTENANCE AND TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
EXERCISE GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
PART LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
EXPLODED DRAWING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
ORDERING REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
TABLE OF CONTENTS
IMPORTANT PRECAUTIONS
WARNING: To reduce the risk of serious injury, read the following important precau-
tions before using the exercise cycle.
WARNING: Before beginning this or any exercise program, consult your physician.
This is especially important for persons over the age of 35 or persons with pre-existing health prob-
lems. Read all instructions before using. ICON assumes no responsibility for personal injury or
property damage sustained by or through the use of this product.
1. Read all instructions in this manual before
using the exercise cycle.
2. Use the exercise cycle only as described in
this manual.
3. It is the responsibility of the owner to ensure
that all users of the exercise cycle are ade-
quately informed of all precautions.
4. The exercise cycle is intended for in-home
use only. Do not use the exercise cycle in a
commercial, rental, or institutional setting.
5. Use the exercise cycle indoors on a level
surface. Keep the exercise cycle away from
moisture and dust. Place a mat under the
exercise cycle to protect the floor or carpet.
6. Inspect and properly tighten all parts regular-
ly. Replace any worn parts immediately.
7. Keep children under the age of 12 and pets
away from the exercise cycle at all times.
8.
The exercise cycle should not be used by
persons weighing more than 250 pounds.
9. Always keep your back straight when using
the exercise cycle. Do not arch your back.
10. Wear appropriate clothes when exercising;
do not wear loose clothes that could become
caught on the exercise cycle. Always wear
athletic shoes.
11. The pulse sensor is not a medical device.
Various factors, including the user's move-
ment, may affect the accuracy of heart rate
readings. The pulse sensor is intended only
as an exercise aid in determining heart rate
trends in general.
12. If you feel pain or dizziness while exercising,
stop immediately and cool down.
13.
The decal shown at the
right has been placed on
the exercise cycle in the
location shown on page
3. If the decal is missing
or illegible, call toll-free
1-877-994-4999, Monday
through Friday, 6 a.m.
until 6 p.m. Mountain
Time, and order a free
replacement decal. Apply
the replacement decal in
the location shown.
3
BEFORE YOU BEGIN
Congratulations for selecting the new REEBOK
®
RB
345 exercise cycle. Cycling is one of the most effec-
tive exercises for increasing cardiovascular fitness,
b
uilding endurance, and toning the entire body. The
R
B 345 exercise cycle offers an impressive array of
features designed to let you enjoy this healthful exer-
cise in the comfort and privacy of your home.
For your benefit, read this manual carefully before
you use the exercise cycle.
If you have questions
after reading this manual, please call our Customer
Service Department toll-free at 1-877-994-4999,
Monday through Friday, 6 a.m. until 6 p.m. Mountain
Time (excluding holidays). To help us assist you,
p
lease mention the product model number and serial
n
umber when calling. The model number is
RBEX69740. The serial number can be found on a
decal attached to the exercise cycle (see the front
cover of this manual for the location of the decal).
Before reading further, please familiarize yourself with
the parts that are labeled in the drawing below.
Console
Fan
Handlebar
BACK
Backrest
Seat Handle
Leveling Pad
Wheel
Pedal with Strap
Water Bottle Holder*
WARNING DECAL
*No water bottle is included
Handgrip Pulse Sensor
Bookrack
Seat
RIGHT SIDE
4
P
lace all parts of the exercise cycle in a cleared area and remove the packing materials.
D
o not dispose of the
packing materials until assembly is completed.
Assembly requires your own adjustable wrench and phillips screwdriver .
U
se the part drawings below to identify the small parts used in assembly. The number in parenthesis below
each drawing refers to the key number of the part, from the PART LIST on page 22. The second number refers
to the quantity used in assembly. Note: Some small parts may have been pre-assembled for shipping. If a
part is not in the parts bag, check to see if it has been pre-assembled.
M10 x 92mm Carriage Bolt (77)–2
M10 Nylon
Locknut (63)–4
M10 x 105mm Carriage Bolt (74)–2
M8 Split
Washer (65)–4
M8 Flat
Washer (18)–4
M8 Nylon
Locknut (56)–4
M6 Washer
(25)–6
M8 x 19mm Button
Bolt (43)–4
M4 x 16mm
Screw (21)–4
M6 x 16mm Screw
(70)–2
M4 x 25mm
Screw (66)–2
M6 x 38mm Hex
Screw (68)–4
M6 x 16mm Hex
Screw (29)–4
M4 x 22mm
Screw (75)–2
M8 x 25mm Button
Screw (27)–4
ASSEMBLY
1. Identify the Front Stabilizer (2), which has Wheels
(59) attached to one side. Attach the Front Stabilizer
to the front of the Frame (1) with two M10 x 92mm
Carriage Bolts (77) and two M10 Nylon Locknuts
(63).
2
59
77
1
63
1
5
2. Attach the Rear Stabilizer (3) to the rear of the
Frame (1) with two M10 x 105mm Carriage Bolts
(
74) and two M10 Nylon Locknuts (63).
3. While a second person holds the Handlebar Post (6)
near the Frame (1) as shown, connect the Upper
Wire Harness (16) to the Lower Wire Harness (58).
Carefully slide the Handlebar Post (6) onto the
Frame (1);
be careful to avoid pinching the W
ire
Harnesses (16, 58). Attach the Handlebar Post to
the Frame with four M8 x 25mm Button Screws (27)
and four M8 Split Washers (65).
2
3
3
6
27
27
65
65
1
16
58
65
65
5.
Insert the Bookrack (55) into the slots in the Console
(9). Attach the Bookrack to the Console with two M4
x 25mm Screws (66). Be careful not to pinch the
wires in the Console.
5
55
66
9
63
6
3
74
1
4. The Console (9) requires four “D” batteries (not
included); alkaline batteries are recommended.
Press the indicated tab on the battery cover and
remove the cover. Press four batteries into the bat-
tery clips; make sure that the batteries are orient-
ed as shown by the markings inside of the bat-
tery clips. Then, reattach the battery cover.
9
Battery
Cover
Batteries
4
6
8. Attach the Seat (12) to the Seat Carriage (11) with
four M6 x 16mm Hex Screws (29) and four M8 Flat
Washers (18).
9.
Identify the Right Seat Handle (79), which is marked
with an “R” sticker.
Attach the Right Seat Handle (79) to the Seat
Carriage (11) with two M8 x 19mm Button Bolts (43)
and two M8 Nylon Locknuts (56) as shown.
Attach the Left Seat Handle (14) to the Seat
Carriage (11) in the same way.
79
14
56
1
1
8
9
12
11
29
29
18
6. Connect the Pulse Wire (60) to the wire extending
from the Console (9). Next, connect the Upper Wire
H
arness (16) to the wire harness on the Console.
Insert all wires into the Handlebar Post (6).
Attach the Console (9) to the Handlebar Post (6)
with four M4 x 16mm Screws (21).
Be careful to
avoid pinching the wires.
9
60
16
Console
Wires
6
21
6
7. Attach the Water Bottle Holder (62) to the Handlebar
Post (6) with two M4 x 22mm Screws (75). Note:
The Water Bottle Holder is designed to be used with
your own water bottle.
75
62
7
6
43
7
12. Firmly tighten the four M8 x 31mm Button Screws
(69) in the Seat Carriage (11). Note: There are two
Button Screws in each side.
Pull the seat knob and slide the Seat Carriage (11)
to the desired position. Release the seat knob and
slide the Seat Carriage back and forth slightly
until it locks into position. Make sure to regularly
tighten the four M8 x 31mm Button Screws (69).
13. Identify the Right Pedal (37), which is marked with
an “R.” Using an adjustable wrench, firmly tighten
the Right Pedal
clockwise
into the Pulley/Crank (19).
Tighten the Left Pedal (not shown)
counterclockwise
into the Pulley/Crank on the left side. After using
the exercise cycle for one week, retighten the
Pedals.
Attach the Right Pedal Strap (38) to the Right Pedal
(37), and press the end of the Right Pedal Strap
onto the tab on the Right Pedal.
Attach the Left
Pedal Strap (not shown) in the same way.
11
69
19
38
37
Tab
12
13
14. Make sure that all parts are properly tightened before you use the exercise cycle. Place a mat
beneath the exercise cycle to protect the floor
.
11. Pull the seat knob and slide the Seat Carriage (11)
onto the Seat Rail (7).
See the inset drawing. Hold the Bumper Axle (50)
inside of the Seat Rail (7). Attach the two Bumpers
(47) to the ends of the Bumper Axle with two M6 x
16mm Screws (70) and two M6 Washers (25) as
shown. Press the Seat Rail Endcap (23) into the
end of the Seat Rail.
11
Knob
7
11
23
50
70
47
25
25
7
10. Attach the Backrest (13) to the Seat Carriage (11)
with four M6 x 38mm Hex Screws (68) and four M6
W
ashers (25).
1
3
25
1
1
25
68
1
0
47
70
Knob
8
HOW TO ADJUST THE POSITION OF THE SEAT
For ef
fective exercise, the seat should be in the proper
position. As you pedal, there should be a slight bend
in your knees when the pedals are in the farthest
position.
T
o adjust
the seat, pull the
seat knob and
slide the seat car-
riage to the desired
position. Release
the seat knob and
slide the seat car
-
riage back and
forth slightly until
it locks into posi
-
tion.
HOW TO ADJUST THE PEDAL STRAPS
T
o adjust the pedal
straps, first pull the
ends of the straps
of
f the tabs on the
pedals. Adjust the
straps to the
desired positions
and press the ends
of the straps back
onto the tabs.
Strap
T
ab
EXERCISE CYCLE OPERATION
HOW TO INSTALL THE RECEIVER FOR THE OPTIONAL CHEST PULSE SENSOR
I
f you purchase the optional chest pulse sensor (
see page 19), follow the steps below to install the receiver
included with the chest pulse sensor.
1. See assembly step 4 on page 5, and remove the two
M4 x 25mm Screws (not shown) and the Bookrack
(55).
Next, look under the console and locate the three indi-
cated screws (not shown). Remove the three screws.
Do not remove the screws attaching the Console to
the Handlebar Post (6).
2. Carefully lift the top of the Console (9) as shown. Using
the two small screws included with the chest pulse sen-
sor, attach the receiver to the indicated plastic posts on
the Console. Make sure that the receiver is turned
exactly as shown.
Connect the wire on the receiver to
the indicated wire on the Console.
See step 1 above. Lower the top of the Console (9).
Make sure that no wires are pinched. Reattach the
top of the Console with the three screws removed in
step 1. See assembly step 4 on page 5, and reattach
the Bookrack (55) with the two M4 x 25mm Screws (not
shown). Note: The remaining wires included with the
chest pulse sensor may be discarded.
Posts
Wire
55
6
9
9
1
Receiver
2
Screws
Screws
Seat
Carriage
Seat
Knob
9
FEATURES OF THE CONSOLE
The advanced console offers a selection of features
designed to make your workouts more enjoyable and
effective. When the manual mode of the console is
selected, the resistance of the pedals can be changed
with the touch of a button. As you exercise, the con-
sole will provide continuous exercise feedback. You
can even measure your heart rate using the handgrip
pulse sensor. Note: See page 19 for information
about an optional chest pulse sensor.
The console also offers six preset programs. Each pro-
gram automatically changes the resistance of the ped-
als and prompts you to increase or decrease
your pace
as it guides you through an effective workout.
In addition, the console features two heart rate pro
-
grams that automatically change the resistance of the
pedals and prompt you to vary your pace to keep your
heart rate near a target heart rate as you exercise.
The console also features iFIT.com interactive technol-
ogy. Having iFIT.com interactive technology is like hav-
ing a personal trainer in your home. Using the included
audio cable, you can connect the exercise cycle to your
home stereo, portable stereo, computer, or VCR and
play special iFIT.com CD and video programs (iFIT.com
CDs and videocassettes are available separately).
iFIT.com CD and video programs automatically control
the resistance of the pedals and prompt you to vary
your pace as a personal trainer coaches you through
every step of your workout. High-energy music pro-
vides added motivation.
To purchase iFIT.com CDs
and videocassettes, call toll-free 1-877-994-4999.
With the exercise cycle connected to your computer,
you can also go to our Web site at www.iFIT
.com and
access programs directly from the internet.
Explore
www.iFIT.com for more information.
T
o use the manual mode of the console,
see page
10. T
o use a preset program,
see page 12. T
o use a
heart rate program,
see page 13. To use an
iFIT.com CD or videocassette, see page 18. T
o use
a program directly from our W
eb site,
see page 19.
Note: If there is a sheet of clear plastic on
the face of the console, remove the plastic.
10
H
OW TO USE THE MANUAL MODE
B
egin pedaling to activate the console.
To activate the console, begin pedaling. After a
few seconds, the console displays will light. A
tone will then sound and the console will be
r
eady for use.
Select the manual mode.
When the power is
turned on, the
manual mode will
be selected. If you
have selected a
program or the
iFIT.com mode,
select the manual mode by pressing the Program
Select button repeatedly until a track appears in
the matrix.
Begin pedaling and change the resistance of
the pedals as desired.
As you pedal,
change the resis-
tance of the ped-
als by pressing the
Resistance but-
tons. There are
ten resistance lev-
els. Note: After the buttons are pressed, it will
take a moment for the pedals to reach the select-
ed resistance level.
Monitor your progress with the matrix and the
two displays.
The matrix
—
When the manual
mode or the
iFIT.com mode is
selected, the
matrix will show a
track representing
1/4 mile. As you exercise, the indicators around
the track will light, one at a time, until the entire
track is lit. The track will then darken and a new
lap will begin.
The upper dis-
play—The upper
display will show
the elapsed time,
the distance you
have pedaled, and
your pedaling pace, in revolutions per minute
(RPM). The display will change from one number
t
o the next every few seconds, as shown by the
indicators in the display. Note: When a program is
s
elected, the display will show the time
r
emaining
in the program instead of the elapsed time. Each
time the resistance of the pedals changes, the
display will show the resistance level.
If desired, you can
select a single
mode for continu-
ous display. Press
the left Mode button
repeatedly until the
desired mode indi-
cator is lit; make sure that the Scan indicator is
not lit.
The lower
display
—The lower
display will show
the approximate
number of calories
you have burned
and your pedaling
speed. The display will change from one number
to the next every few seconds, as shown by the
indicators in the display. The display will also
show your heart rate (pulse) when you use the
handgrip pulse sensor or the optional chest pulse
sensor.
Note: The console
can show speed
and distance in
either miles or
kilometers. The let-
ters MPH or KPH
will appear in the
lower display to show which unit of measurement
is selected. To change the unit of measurement,
first hold down the Program Select button for a few
seconds.
An E (for English) or an M (for metric) will
appear in the lower display. Press the Resistance
+ button to change the unit of measurement. Then,
press the Cooling Fan button. Note: When the bat
-
teries are replaced, it may be necessary to rese-
lect the desired unit of measurement.
If desired, you can select a single mode for con-
tinuous display. Press the right Mode button
repeatedly until the desired mode indicator is lit;
make sure that the Scan indicator is not lit.
4
3
2
1
11
M
easure your heart rate if desired.
You can measure your heart rate using either the
handgrip pulse sensor or the optional chest pulse
sensor. Note: If you hold the handgrip pulse
sensor and wear the chest pulse sensor at the
same time, the console will not display your
h
eart rate accurately.
If there are
thin sheets of
plastic on the
metal con-
tacts on the
handgrip
pulse sensor,
peel off the
plastic.
To
measure your
heart rate, hold the contacts; your palms must be
resting on the contacts closest to you, and your
fingers must be touching the opposite contacts.
Avoid moving your hands.
When your pulse
is detected, the
heart-shaped indi-
cator in the lower
display will flash
each time your
heart beats, and
your heart rate will be shown. For the most accu-
rate heart rate reading, hold the contacts for at
least 15 seconds.
Note: If you continue to hold the pulse sensor, the
lower display will show your heart rate for up to
3
0 seconds. The display will then show your heart
rate along with the other modes.
If your heart rate is not shown, make sure that
your hands are positioned as described. Avoid
moving your hands excessively or squeezing the
metal contacts too tightly. For optimal performance,
periodically clean the metal contacts using a soft
cloth; never use alcohol, abrasives, or chemicals.
Turn on the fan if desired.
To turn on the fan at low speed, press the Cooling
Fan button. To turn on the fan at high speed,
press the button a second time. To turn off the
fan, press the button a third time. Note: If the fan
is turned on but the pedals are not moved for thir-
ty seconds, the fan will automatically turn off.
When you are finished exercising, the console
will automatically turn off.
If the pedals are not moved for a few seconds, a
tone will sound, the console will pause, and the
upper display will begin to flash.
If the pedals are not moved for about five min-
utes, the console will turn off and the displays will
be reset.
7
6
5
Contacts
12
H
OW TO USE PRESET PROGRAMS
B
egin pedaling to activate the console.
See step 1 on page 10.
Select one of the six preset programs.
When the power is
turned on, the
manual mode will
be selected. To
select a preset
program, press the
Program Select
button repeatedly until “P1,” “P2,” “P3,” “P4,”
“P5,” or “P6” appears in the lower display.
When a preset program is selected, the matrix
will show the first six resistance settings of the
program.
Press the Program Start button or begin
pedaling to start the program.
Each program is divided into several time seg-
ments of different lengths. One resistance setting
is programmed for each segment. (The same
resistance setting may be programmed for two or
more consecutive segments.)
The resistance
setting for the first
segment will be
shown in the flash-
ing Current
Segment column
of the matrix. The
resistance settings
for the next five
segments
will be shown in the columns to the
right.
When only three seconds remain in the first seg-
ment of the program,
a series of tones will sound;
all resistance settings will then move one column
to the left.
The resistance setting for the second
segment will then be shown in the flashing
Current Segment column and the resistance of
the pedals will automatically change to the resis-
tance setting for the second segment.
The program will continue until the resistance set-
ting for the last segment is shown in the Current
S
egment column of the matrix and no time
remains in the program.
Note: During the program, you can override the
resistance setting for the current segment by
pressing the Resistance buttons. However, when
the next segment begins, the resistance will auto-
matically change if a different resistance setting is
programmed for the next segment. If you stop
pedaling for several seconds, a tone will sound
and the program will pause. To restart the pro-
gram, simply resume pedaling.
Use the pace (RPM) guide.
During preset pro-
grams, the pace
guide will prompt
you to increase or
decrease your ped-
aling pace. When
one of the indica-
tors on the left side
of the pace guide
lights, increase
your pace; when
one of the indica-
tors on the right side lights, decrease your pace.
When the center indicator lights, maintain your
current pace.
Important: The pace settings of
the program are intended only to provide a
goal. Make sure to pedal at a pace that is
comfortable for you.
Monitor your progress with the two displays.
See step 4 on page 10.
Measure your heart rate if desired.
See step 5 on page 1
1.
Turn on the fan if desired.
See step 6 on page 1
1.
When you are finished exercising, the console
will automatically turn off.
See step 7 on page 11.
8
7
6
5
4
3
2
1
Current Segment
13
H
OW TO USE HEART RATE PROGRAMS
Heart rate program 1 is designed to keep your heart
rate between 60% and 85% of your
estimated maxi-
mum heart rate
while you exercise. Note: Your maxi-
m
um heart rate is estimated by subtracting your age
from 220. For example, if you are 30 years old, your
estimated maximum heart rate is 190 (220 – 30 =
190).
Heart rate program 2 will keep your heart rate near a
target heart rate that you select.
Follow the steps below to use a heart rate program.
Begin pedaling to activate the console.
See step 1 on page 10.
Select one of the heart rate programs.
To select a heart
rate program,
press the Program
Select button
repeatedly until
“H1” or “H2”
appears in the
lower display.
If you selected
heart rate program
1, the matrix will
show the first six
target heart rate
settings of the pro-
gram.
If you selected
heart rate program
2, a heart symbol
will appear in the
matrix.
If you selected heart rate program 1, go to
step 3. If you selected heart rate program 2,
go to step 4.
E
nter your age.
When heart rate
program 1 is
selected, you must
enter your age. If
you have already
e
ntered your age,
press the Enter
(Program Start)
button and go to
step 5. If you have
not entered your
age, press the + or
– button repeatedly to enter your age, and then
press the Enter button. Note: Once you have
entered your age, it will be saved in memory.
Enter a target heart rate.
When heart rate
program 2 is
selected, you must
enter a target heart
rate. (See the heart
rate chart on page
21 for heart rate
guidelines.) To
enter a target heart
rate, press the + or
– button repeated-
ly, and then press
the Enter (Program Start) button.
Hold the handgrip pulse sensor or wear the
optional chest pulse sensor.
To use a heart rate program, you must hold the
handgrip pulse sensor or wear the optional chest
pulse sensor. If you use the handgrip pulse sen-
sor, it is not necessary to hold the handgrips con-
tinuously during the program. However, you
should hold the handgrips frequently for the pro-
gram to operate properly.
Each time you hold
the handgrips, keep your hands on the metal
contacts for at least 30 seconds.
Note: When
you are not holding the handgrips, the letters
“PLS” will appear in the lower display instead of
your heart rate.
5
4
3
2
1
14
Begin pedaling.
E
ach heart rate program is divided into 30 one-
minute segments. One target heart rate is pro-
g
rammed for each segment. Note: The same tar-
get heart rate may be programmed for two or
more consecutive segments. If heart rate pro-
gram 2 is selected, the same target heart rate is
programmed for all segments.
If heart rate pro-
gram 1 is select-
ed,
the target
heart rate setting
for the first seg-
ment will be
shown in the
flashing Current
Segment column
of the matrix. The target heart rate settings for the
next five segments will be shown in the columns
to the right. When only three seconds remain in
the first segment of the program, a series of
tones will sound;
all target heart rate settings will
then move one column to the left.
The target
heart rate setting for the second segment will
then be shown in the flashing Current Segment
column.
If heart rate program 2 is selected, the same
target heart rate is programmed for all segments;
therefore, the target heart rate settings will not be
shown in the matrix. When only three seconds
remain in the first segment of the program,a
series of tones will sound and the time will flash
in the right display.
As you pedal, the console will regularly compare
your heart rate to the target heart rate. If your
heart rate is too far below or above the target
heart rate, the resistance of the pedals will auto-
matically increase or decrease to being your heart
rate closer to the target heart rate.
The pace guide
will help you to
m
aintain a con-
stant pace during
t
he program. When
one of the indica-
tors on the left side
of the pace guide
lights, increase
your pace; when
one of the indica-
tors on the right
side lights, decrease your pace. When the center
indicator lights, maintain your current pace.
Important: The pace settings of the program
are intended only to provide a goal. Make
sure to pedal at a pace that is comfortable for
you.
The program will continue until the target heart
rate setting for the last segment is shown in the
Current Segment column of the matrix and no
time remains in the program.
Note: During the program, you can manually
change the resistance setting, if desired, by
pressing the Resistance buttons. However, when
the console compares your heart rate to the tar-
get heart rate, the resistance may automatically
change. If you stop pedaling for several seconds,
a tone will sound and the program will pause. To
restart the program, simply resume pedaling.
Monitor your progress with the two displays.
See step 4 on page 10.
Turn on the fan if desired.
See step 6 on page 11.
When you are finished exercising, the con-
sole will automatically turn off.
See step 7 on page 11.
9
8
7
6
Current Segment
15
HOW TO CONNECT YOUR CD PLAYER, VCR,
OR COMPUTER
T
o use iFIT.com CDs
,
the exercise cycle must be con-
nected to your portable CD player, portable stereo,
home stereo, or computer with CD player. See pages
15 and 16 for connecting instructions. To use iFIT.com
videocassettes, the exercise cycle must be connected
to your VCR. See page 17 for connecting instructions.
To use iFIT.com programs directly from our Web
site, the exercise cycle must be connected to your
home computer. See page 16 for connecting instruc-
tions.
HOW TO CONNECT YOUR PORTABLE CD PLAYER
Note: If your CD player has separate LINE OUT and
PHONES jacks, see instruction A below. If your CD
player has only one jack, see instruction B.
A. Plug one end of the audio cable into the jack
beneath the console. Plug the other end of the
cable into the LINE OUT jack on your CD player.
Plug your headphones into the PHONES jack.
B. Plug one end of the audio cable into the jack
beneath the console. Plug the other end of the
cable into a 1/8”
Y-adapter (available at electronics
stores). Plug the Y-adapter into the PHONES jack
on your CD player. Plug your headphones into the
other side of the Y-adapter.
HOW TO CONNECT YOUR PORTABLE STEREO
N
ote: If your stereo has an RCA-type AUDIO OUT
jack, see instruction A below. If your stereo has a
1
/8” LINE OUT jack, see instruction B. If your
stereo has only a PHONES jack, see instruction C.
A. Plug one end of the audio cable into the jack
beneath the console. Plug the other end of the cable
into the adapter. Plug the adapter into an AUDIO
OUT jack on your stereo.
B. Plug one end of the audio cable into the jack
beneath the console. Plug the other end of the
cable into the LINE OUT jack on your stereo. Do
not use the adapter.
C. Plug one end of the audio cable into the jack
beneath the console. Plug the other end of the
cable into a 1/8” Y-adapter (available at electronics
stores). Plug the Y-adapter into the PHONES jack
on your stereo. Plug your headphones into the
other side of the Y-adapter.
LINE OUT
PHONES
L
INE OUT
PHONES
Audio
Cable
Head-
phones
A
P
HONES
PHONES
Audio
Cable
1/8”
Y-adapter
Headphones
B
AUDIO OUT
RIGHT
LEFT
PHONES
Audio
Cable
C
1/8”
Y-adapter
Headphones
Audio Cable
Adapter
A, B
16
HOW TO CONNECT YOUR HOME STEREO
N
ote: If your stereo has an unused LINE OUT jack,
see instruction A below. If the LINE OUT jack is
b
eing used, see instruction B.
A. Plug one end of the audio cable into the jack
beneath the console. Plug the other end of the
cable into the adapter. Plug the adapter into the
LINE OUT jack on your stereo.
B. Plug one end of the audio cable into the jack
beneath the console. Plug the other end of the
cable into the adapter. Plug the adapter into an
RCA Y-adapter (available at electronics stores).
Next, remove the wire that is currently plugged into
the LINE OUT jack on your stereo and plug the
wire into the unused side of the Y-adapter. Plug the
Y-adapter into the LINE OUT jack on your stereo.
HOW TO CONNECT YOUR COMPUTER
N
ote: If your computer has a 1/8” LINE OUT jack,
see instruction A. If your computer has only a
P
HONES jack, see instruction B.
A. Plug one end of the audio cable into the jack
beneath the console. Plug the other end of the
cable into the LINE OUT jack on your computer.
B. Plug one end of the audio cable into the jack
beneath the console. Plug the other end of the
cable into a 1/8” Y-adapter (available at electronics
stores). Plug the Y-adapter into the PHONES jack
on your computer. Plug your headphones or speak-
ers into the other side of the Y-adapter.
CD
VCR
Amp
L
INE OUT
LINE OUT
Audio Cable
Adapter
A
CD
VCR
Amp
LINE OUT
Audio
Cable
RCA
Y-adapter
W
ire removed from
LINE OUT
jack
B
Adapter
LINE OUT
Audio
Cable
A
PHONES
Audio Cable
B
1/8”
Y-adapter
Headphones/Speakers
17
HOW TO CONNECT YOUR VCR
N
ote: If your VCR has an unused AUDIO OUT jack,
see instruction A below. If the AUDIO OUT jack is
b
eing used, see instruction B. If you have a TV
with a built-in VCR, see instruction B. If your VCR
is connected to your home stereo, see HOW TO
CONNECT YOUR HOME STEREO on page 16.
A. Plug one end of the audio cable into the jack
beneath the console. Plug the other end of the
cable into the adapter. Plug the adapter into the
AUDIO OUT jack on your VCR.
B. Plug one end of the audio cable into the jack
beneath the console. Plug the other end of the
c
able into the adapter. Plug the adapter into an
RCA Y-adapter (available at electronics stores).
N
ext, remove the wire that is currently plugged into
the AUDIO OUT jack on your VCR and plug the
wire into the unused side of the Y-adapter. Plug the
Y-adapter into the AUDIO OUT jack on your VCR.
AUDIO OUT
RIGHT
LEFT
VIDEO AUDIO
A
NT. IN
RF OUT
IN
O
UT
CH
3
4
Audio Cable
Adapter
A
VIDEO AUDIO
A
NT. IN
R
F OUT
I
N
OUT
CH
34
A
Audio Cable
Adapter
B
Wire removed from
AUDIO OUT jack
RCA Y-adapter
18
To use iFIT.com CDs or videocassettes, the exercise
cycle must be connected to your portable CD player,
portable stereo, home stereo, computer with CD play-
er, or VCR. See HOW TO CONNECT YOUR CD
P
LAYER, VCR, OR COMPUTER on pages 15 to 17.
To purchase iFIT.com CDs and videocassettes, call
toll-free 1-877-994-4999.
Follow the steps below to use an iFIT.com CD or
video program.
Begin pedaling to activate the console.
See step 1 on page 10.
Select the iFIT.com mode.
When the console is
turned on, the man-
ual mode will be
selected. To select
the iFIT.com mode,
press the iFIT.com
button. The indicator
on the button will light.
Insert the iFIT.com CD or videocassette.
If you are using an iFIT.com CD, insert the CD
into your CD player. If you are using an iFIT.com
videocassette, insert the videocassette into your
VCR.
Press the play button on your CD player or
VCR.
A
moment after the play button is pressed, your
personal trainer will begin guiding you through
your workout. Simply follow your personal trainer’s
instructions.
T
he program will function in almost the same way
as a preset program (see steps 3 and 4 on page
12). However, an electronic “chirping” sound will
alert you when the resistance of the pedals and/or
t
he target pace is about to change.
Note: If the resistance of the pedals and/or the
target pace does not change when a “chirp” is
heard:
• Make sure that the indicator above the
iFIT.com button is lit.
• Adjust the volume of your CD player or VCR.
If the volume is too high or too low, the con-
sole may not detect the program signals.
• Make sure that the audio cable is properly
connected and that it is fully plugged in.
Monitor your progress with the two displays.
See step 4 on page 10.
Measure your heart rate if desired.
See step 5 on page 11.
Turn on the fan if desired.
See step 6 on page 11.
When you are finished exercising, the console
will automatically turn off.
See step 7 on page 11.
8
7
6
5
4
3
2
1
HOW TO USE IFIT.COM CD AND VIDEO
PROGRAMS
19
HOW TO USE PROGRAMS DIRECTLY FROM
OUR WEB SITE
Our Web site at www.iFIT.com allows you to play
iFIT.com programs directly from the internet. To use
programs from our Web site, the exercise cycle must
be connected to your home computer. See HOW TO
CONNECT YOUR COMPUTER on page 16. In addi-
tion, you must have an internet connection and an
internet service provider. A list of specific system
requirements is found on our Web site.
Follow the steps below to use a program from our
Web site.
Begin pedaling to activate the console.
See step 1 on page 10.
Select the iFIT.com mode.
When the console is
turned on, the manu-
al mode will be
selected. To select
the iFIT.com mode,
press the iFIT.com
button. The indicator
on the button will light.
Go to your computer and start an internet
connection.
Start your Web browser, if necessary, and go
to our Web site at www.iFIT.com.
Follow the desired links on our W
eb site to
select a program.
Read and follow the on-line instructions for using
a program.
Follow the on-line instructions to start the
program.
When you start the program, an on-screen count-
down will begin.
Return to the exercise cycle and begin
pedaling.
When the on-screen countdown ends, the pro-
gram will begin. The program will function in
a
lmost the same way as a preset program (see
steps 3 and 4 on page 12). However, an electronic
“chirping” sound will alert you when the resistance
of the pedals and/or the target pace is about to
change.
Monitor your progress with the two displays.
See step 4 on page 10.
Measure your heart rate if desired.
See step 5 on page 11.
Turn on the fan if desired.
See step 6 on page 11.
When you are finished exercising, the console
will automatically turn off.
See step 7 on page 11.
THE OPTIONAL CHEST PULSE SENSOR
The optional chest pulse sensor provides hands-free
operation and continuously monitors your heart rate
during your workouts. To purchase the optional
chest pulse sensor, call toll-free 1-877-994-4999.
11
10
9
8
7
6
5
4
3
2
1
20
I
nspect and properly tighten all parts of the exercise
cycle regularly. The exercise cycle can be cleaned
with a soft, damp cloth. To prevent damage to the
console, keep liquids away from the console and keep
t
he console out of direct sunlight.
TIGHTENING THE PEDALS
For best performance, regularly tighten both pedals.
CONSOLE TROUBLESHOOTING
If the console display becomes dim, the batteries
should be replaced. See assembly step 4 on page 5
for replacement instructions. If the console does not
display your heart rate when you use the handgrip
pulse sensor, see step 5 on page 13.
HOW T
O LEVEL THE EXERCISE CYCLE
If the exercise
cycle does not sit
flat on the floor,
turn one or both
of the leveling
pads until the
exercise cycle is
level.
HOW TO ADJUST THE REED SWITCH
If the console does not display correct feedback, the
reed switch should be adjusted. To adjust the reed
switch, remove the indicated M4 x 48mm Screws (20)
and M4 x 16mm Screws (21) from the Left Side
Shield (4). Using an adjustable wrench, turn the Left
Pedal (40) clockwise and remove it. Turn the left side
o
f the Crank (19) so that it is pointing toward the front
of the exercise cycle, and then slide off the Left Side
Shield.
L
ocate the
Reed Switch
(44). Turn the
Crank (19)
until the
Magnet (54) is
aligned with
the Reed
Switch.
Loosen, but
do not
remove, the
indicated M4
x 16mm Screw (21). Slide the Reed Switch slightly
closer to or away from the Magnet.
Then, retighten
the Screw. Turn the Left Crank Arm for a moment.
Repeat until the console displays correct feedback.
When the Reed Switch is correctly adjusted, reattach
the left side shield and the left pedal.
HOW TO ADJUST THE DRIVE BELT
If you can feel the pedals slip while you are pedaling,
even when the resistance is at the highest level, the
Drive Belt (64) may need to be adjusted. See HOW
TO ADJUST THE REED SWITCH at the left. To adjust
the Drive Belt, the Right Side Shield (5) must first be
removed. Remove the indicated M4 x 48mm Screws
(20) from the Left Side Shield (4) and the M4 x 16mm
Screws (not shown) from the Right Side Shield. Using
an adjustable wrench, turn the Right Pedal (not
shown) counterclockwise and remove it. Next, turn the
right side of the Crank (19) so that it is pointing
toward the front of the exercise cycle, and then slide
off the Right Side Shield.
Next, turn the
indicated M8 x
35mm Screw
(72) until the
Drive Belt (64)
is properly
tightened.
Then, reattach
the right side
shield and the
right pedal.
MAINTENANCE AND TROUBLESHOOTING
Leveling
Pads
20
21
5
4
40
72
19
64
44
21
54
19
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24

Pro-Form GT 120 User manual

GT 120
Pro-Form
Brand
Pro-Form
Model
GT 120
Category
Fitness, gymnastics & weight training
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents