STIEBEL ELTRON DHC-E 8/10 Installation guide

Brand: STIEBEL ELTRON

Model: DHC-E 8/10

Category: Space heaters

Type: Installation guide

This manual is also suitable for

DHC-E 12

OPERATION AND INSTALLATION

OPERACIÓN E INSTALACIÓN

UTILISATION ET INSTALLATION

ELECTRONICALLY CONTROLLED INSTANTANEOUS WATER HEATER | CALENTADOR INSTANTÁNEO

CON CONTROLADO ELECTRÓNICA | CHAUFFE-EAU INSTANTANÉ À GESTION ÉLECTRONIQUE

»DHC-E 8/10

»DHC-E 11L

»DHC-E 12

The DHC-E series is

tested and certiﬁ ed

by WQA against NSF/

ANSI 372 for lead free

compliance.

STIEBEL ELTRON, Inc.

17 West Street | West Hatﬁ eld, MA 01088

Tel. 413-247-3380 | Fax 413-247-3369

Email info@stiebel-eltron-usa.com

www.stiebel-eltron-usa.com

2 | DHC-E WWW.STIEBEL-ELTRON-USA.COM

CONTENTS | OPERATION

OPERATION

1. General information _________________________________________2

1.1 Safety information _______________________________________________ 2

1.2 Other symbols in this document ______________________________ 3

2. Safety __________________________________________________________3

2.1 Intended use ______________________________________________________ 3

2.2 General Information_____________________________________________ 3

2.3 Safety Precautions _______________________________________________ 3

2.4 Test symbols ______________________________________________________ 3

3. General ________________________________________________________4

4. Troubleshooting ______________________________________________4

INSTALLATION

5. Mounting the appliance _____________________________________5

5.1 Application ________________________________________________________ 5

5.2 Mounting __________________________________________________________ 5

5.3 Water connections _______________________________________________ 5

6. Electrical connection _________________________________________6

6.1 DHC-E 8/10 - Appliance with output power options ______ 6

6.2 Temperature setting/anti-scalding protection ____________ 7

7. Commissioning _______________________________________________7

7.1 Appliance handover _____________________________________________ 7

8. Troubleshooting ______________________________________________7

8.1 Display options LED diagnostic „trafﬁ c lights“ _____________ 7

8.2 Fault table _________________________________________________________ 7

9. Normal maintenance _________________________________________7

10. Technical Data ________________________________________________8

10.1 Dimensioned drawing __________________________________________ 8

10.2 Wiring diagram __________________________________________________ 8

10.3 Maximum temperature increase above ambient water

temperature ______________________________________________________ 9

10.4 Data table ________________________________________________________ 10

11. Spare parts _________________________________________________ 10

12. Warranty ____________________________________________________ 11

OPERATION

1. General information

Note

Read these instructions carefully before using the ap-

pliance and familiarize yourself with its functions. Keep

these instructions safe. Pass on the instructions to a new

user if required.

1.1 Safety information

1.1.1 Structure of safety information

KEYWORD Type of risk

Here, possible consequences are listed that may re-

sult from not observing the safety information.

 Steps to prevent the risk are listed.

1.1.2 Symbols. type of risk

Symbol Type of risk

Injury

Electrocution

Burns or scalding

1.1.3 Keywords

KEYWORD Description

DANGER If this information is not observed, it will result in serious

injury or death.

WARNING If this information is not observed, it can result in serious

injury or death.

CAUTION If this information is not observed, it can lead to medium

or minor injury.

OPERATION

SAFETY

ENGLISH

WWW.STIEBEL-ELTRON-USA.COM DHC-E | 3

1.2 Other symbols in this document

Note

Notes are bordered by horizontal lines above and below

the text. General information is identiﬁ ed by the symbol

shown on the left.

 Read these notes carefully.

Symbol

Damage to the appliance and environment

Appliance disposal

 This symbol indicates that you have to do something. The ac-

tion you need to take is described step by step.

2. Safety

Observe the following safety information and regulations.

Operate the appliance only when fully installed and with all safety

equipment ﬁ tted.

2.1 Intended use

The appliance is intended for heating domestic hot water and can

supply several draw-off points.

Any other use beyond that described shall be deemed inappro-

priate.

Observation of these instructions is also part of the correct use

of this appliance.

2.2 General Information

Read this entire manual. Failure to follow all the guides, instruc-

tions and rules could cause personal injury or property damage.

Improper installation, adjustment, alteration, service and use of

this appliance can result in serious injury.

This appliance must be installed by a licensed electrician and

plumber. The installation must comply with all national, state and

local plumbing and electric codes. Proper installation is the re-

sponsibility of the installer. Failure to comply with the installation

and operating instructions or improper use voids the warranty.

Save these instructions for future reference. Installer should leave

these instructions with the consumer.

If you have any questions regarding the installation, use or opera-

tion of this water heater, or if you need any additional installation

manuals, please call our technical service line, see last side.

2.3 Safety Precautions

DANGER Injury

Please read and follow these instructions.

Failure to follow these instructions could result in seri-

oius personal injury or death.

Damage to the appliance and the environment

The appliance must be installed by a licensed electrician

and plumber. The installation must comply with all nati-

onal, state and local plumbing and electric codes.

Service of the appliance must be performed by qualiﬁ ed

service TECHNICIANS.

DANGER Electrocution

Before proceeding with any installation, adjustment. al-

teration, or service of this appliance all circuit breakers

and disconnect switches servicing the appliance must

be turned off. Failure to do so could result in serious

personal injury or death.

DANGER Electrocution

Never remove the appliance‘s cover unless the electricity

servicing the appliance is turned off. Failure to do so

could result in personal injury or death.

DANGER Electrocution

The appliance must be properly grounded. Failure to

electrically ground the product could result in serious

personal injury or death.

DANGER Burns

Water temperatures over 125°F (52 °C)can cause severe

burns instantly or death from scalding. A hot water scal-

ding potential exists if the thermostat on the appliance

is set too high. Households with small children, disabled

or elderly persons may require that the thermostat be

set at 113°F (45 °C) or lower to prevent possible injury

from hot water.

WARNING Injury

Where children or persons with limited physical, sensory

or mental capabilities are to be allowed to control this

appliance, ensure that this will only happen under su-

pervision or after appropriate instructions by a person

responsible for their safety.

Children should be supervised to ensure that they never

play with the appliance.

2.4 Test symbols

See type plate on the appliance.

OPERATION

GENERAL

4 | DHC-E WWW.STIEBEL-ELTRON-USA.COM

3. General

The tankless water heater differs from conventional storage type

water heaters in several ways. It does not store hot water. Instead,

water is heated instantaneously as it ﬂ ows through the appliance.

Due to the absence of stand-by losses, the appliance offers greater

energy efﬁ ciency than storage type water heaters.

26_02_02_1086

The input of heat into the water is electronically controlled. The

appliance will deliver any water temperature between 86°F (30

°C) and 140 °F (60 °C). Please set the desired temperature using

the knob on the front cover.

Note

For reasons of appliance efﬁ ciency and durability (sca-

ling), the optimum temperature setting lies between 86°F

(30°C) and 120°F (50°C).

In case the “Power” light is ﬂ ashing while the appliance operates,

the water ﬂ ow rate exceeds the heating capacity of the appli-

ance. Reduce the hot water ﬂ ow rate in order to let the appliance

achieve the set point temperature. The maximum temperature is

electronically limited to 140 °F (60 °C). In case you have questions

regarding the way you plan to use the appliance, please call our

technical service line, see last side.

4. Troubleshooting

Symptom Possible Cause  Solution

No hot water not enough flow rate to

activate appliance

clean faucet aerator or shower

head

Water not hot enough water flow too high reduce water flow rate until

light on front cover stops

blinking

If you cannot remedy the fault, notify the contractor who installed

the appliance. To facilitate and speed up your enquiry, please pro-

vide the serial number from the type plate (000000-0000-000000).

ENGLISH

WWW.STIEBEL-ELTRON-USA.COM DHC-E | 5

INSTALLATION

MOUNTING THE APPLIANCE

INSTALLATION

5. Mounting the appliance

5.1 Application

One appliance can be used for the following applications:

one or multiple hand washing sinks

one kitchen sink

cabins with ﬂ ow restriction at shower head.

A combination of two appliance can be used for whole apartment

and house applications. Please contact STIEBEL ELTRON for special

installation instructions.

All areas with a ground water temperature likely to exceed 65°F

(18°C) year round:

Whole apartment or house

CAUTION Electrocution

Unit must be installed in a vertical position with the

water ﬁ ttings pointing downward. In this position the

unit is splashproof, so that no water can soak in.

26_02_02_1082

26_02_02_1081

1 Hot valve (left)

2 Cold valve (right)

3 Sink

4 1/2“ main pipe

5 Water supply line for faucet installation

6 Shut-off valve

7 Electrical junction box

5.2 Mounting

 Install appliance as close as possible to the main hot water

draw-off points.

 Install appliance in a frost free area. If frost may occur, re-

move appliance before freezing temperatures set in.

 Leave a minimum of 5“ of clearance on all sides for servicing.

26_02_02_1083

 Remove plastic cover.

26_02_02_033126_02_02_1090

 Screw the screws into the wall and hang the appliance.

Screws and plastic wall anchors for mounting on masonry or

wood are provided.

 Secure the screws.

5.3 Water connections

Damage to the appliance and the environment

Excessive heat from soldering on copper pipes near the

DHC may cause damage.

6 | DHC-E WWW.STIEBEL-ELTRON-USA.COM

INSTALLATION

ELECTRICAL CONNECTION

 All plumbing work must comply with national and applicable

state and local plumbing codes.

 Notice for Australia / New Zealand:

The installation shall comply with AS/NZS 3500.4.

 A pressure reducing valve must be installed if the cold water

supply pressure exceeds 150 PSI (10 bar).

 Make certain that the cold water supply line has been ﬂ ushed

to remove any scale and dirt.

 Install isolating valve in cold water line as shown in illustra-

tion “Mounting the appliance”. This allows the appliance to

be isolated for maintenance purposes.

 Cold water connection (inlet) is on the right side of the ap-

pliance, hot water connection (outlet) is on the left side of

appliance.

 Tankless water heaters such as the DHC-E are not required to

be equipped with a Pressure and Temperature Relief Valve

(P&T). If the local inspector will not pass the installation

without a P&T, it should be installed on the hot water outlet

side of appliance.

 The appliance is designed for connection to copper tubing,

PEX tubing or a braided stainless steel hose with a ½“ NPT

female tapered thread. If soldering near the appliance is nec-

essary, please direct the ﬂ ame away from the plastic housing

of the appliance in order to avoid damage.

 When all plumbing work is completed, check for leaks and

take corrective action before proceeding.

6. Electrical connection

DANGER Electrocution

Carry out all electrical connection and installation work

in accordance with relevant regulations.

DANGER Electrocution

Only use a permanent connection to the power supply.

The appliance must be able to be separated from the

power supply by an isolator that disconnects all poles

with at least 3mm contact separation.

Damage to the appliance and the environment

Observe the type plate. The speciﬁ ed voltage must match

the mains voltage.

DANGER Electrocution

Before beginning any work on the electric installati-

on, be sure that main breaker panel switch is „off“ to

avoid any danger of electric shock. All mounting and

plumbing must be completed before proceeding with

electrical hook-up. Where required by local, state or

national electrical codes the circuit should be equipped

with a „ground fault interrupter“.

DANGER Electrocution

As with any electric appliance. failure to electrically

ground appliance may result in serious injury or death.

 The appliance should be connected to a properly grounded

dedicated branch circuit of proper voltage rating. In installa-

tions with several appliances, each appliance requires an

independent circuit. Please refer to the technical data table

for the correct wire and circuit breaker size.

26_02_02_1084

 The wire must be fed through the rubber seal located be-

tween the hot and cold water connections. Then feed wires

through strain relief clamp and tighten clamp down on wire.

The „live“ wires must be connected to the slots on the ter-

minal block marked L and L (L and N). The ground wire must

be connected to slot marked with the ground symbol. Strain

relief clamp with screws and rubber seal are provided.

6.1 DHC-E 8/10 - Appliance with output power op-

tions

For the DHC-E 8/10 instantaneous water heater, the output power

is adjustable in 2 stages. In its delivered condition the appliance

is set to 7.2 kW@240 V.

26_02_02_1088

1 coding plug

If the appliance should be installed with a different output power,

take the following steps:

 Insert the coding plug to the desired performance.

Stage 1 208 V 220 V 230 V 240 V

5,4 kW 6,0 kW 6,6 kW 7,2 kW

Stage 2 208 V 220 V 230 V 240 V

7,2 kW 8,1 kW 8,8 kW 9,6 kW

 Mark the selected output power and voltage on the type plate

with a permanent marker.

ENGLISH

WWW.STIEBEL-ELTRON-USA.COM DHC-E | 7

INSTALLATION

COMMISSIONING

6.2 Temperature setting/anti-scalding protection

26_02_02_1089

 Connect the lead of the electronic temperature control to po-

sition „A1“ in order to get the maximum outlet temperature

of 140°F (60°C).

The maximum temperature can be limited to 109°F (43°C):

 Connect the lead of the electronic temperature control to po-

sition „A2“.

 Reinstall the plastic cover.

7. Commissioning

DANGER Electrocution

Commissioning must only be carried out by an authorised

contractor in accordance with safety regulations.

Damage to the appliance and the environment

Open hot water faucet for a few minutes until water ﬂ ow

is continuous and all air is purged from water pipes. The

appliance’s plastic cover must be installed before the cir-

cuit breaker is turned on.

 Turn on circuit breaker to bring electrical power to the

appliance.

 Turn the temperature selector clockwise and anti-clockwise,

to calibrate the temperatur selector.

 Adjust the water temperature to the desired level using the

knob on the front cover of the appliance.

 Turn on hot water and wait twenty seconds until temperature

has stabilized.

 Check the water temperature with your hand and make sure

that it does not feel too hot. Reduce temperature if this is

necessary. A setting of 108°F - 116°F (42 - 47°C) is recom-

mended for most applications.

 Explain to the user how the appliance works and familiarise

him or her with its use.

 Advise the user about possible hazards (hot water tempera-

ture up to 140°F (60°C). Hand over these instructions, to be

kept for future reference.

 A setting of 108°F - 116°F (42 - 47 °C) is recommended for

most applications.

7.1 Appliance handover

Explain the functions of the appliance to the user. Draw special

attention to the safety information. Hand the operating and instal-

lation instructions to the user.

8. Troubleshooting

Danger of electrocution

To test the appliance, it must be supplied with power.

8.1 Display options LED diagnostic „trafﬁ c lights“

Display options

red illuminates in case of faults

yellow illuminates when the appliance is heating water

green flashing: The appliance is supplied with power

26_02_02_1088

1 LED diagnostic „trafﬁ c lights“

8.2 Fault table

Symptom Possible Cause  Solution

No hot water

circuit breaker off

safety thermal cut-out

tripped

turn circuit breaker on

reset thermal cut-out

not enough flow rate to

activate appliance

clean filter screen at appli-

ance

clean faucet aerator or

shower head

Not enough hot water filter screen clogged clean filter screen at appli-

ance

Water not hot enough water flow too high

reduce water flow rate until

light on front cover stops

blinking

supply correct voltage to

appliance

 If you are not able to resolve a problem please contact us,

see last side, before removing the appliance from the wall.

STIEBEL ELTRON is happy to provide technical assistance. In

most instances, we can resolve the problem over the phone.

9. Normal maintenance

STIEBEL ELTRON tankless water heaters are designed for a very

long service life. Actual life expectancy will vary with water qual-

ity and use. The appliance itself does not require any regular

maintenance.

8 | DHC-E WWW.STIEBEL-ELTRON-USA.COM

INSTALLATION

TECHNICAL DATA

However, to ensure consistent water ﬂ ow, it is recommended to

periodically remove scale and dirt that may build up at the aera-

tor of the faucet(s), the ﬁ lter screen in the appliance, or in the

shower head.

10. Technical Data

10.1 Dimensioned drawing

b01

c06 c01

c01

c06

38 (1.5")

360 (14.17")

200 (7.88")

100 (3.94")

110 (4.33")

273 (10.75")75 (2.953")

8 (0.315")

D0000017762

b01 Electrical cable entry

c01 cold water inlet ½"NPT

c06 hot water outlet ½“NPT

10.2 Wiring diagram

DHC-E 8/10

2/GRD ~ 208 / 240 V

1/N/PE ~ 220 / 230 / 240 V

85_02_03_0001

DHC-E 12

2/GRD ~ 208 / 240 V

1/N/PE ~ 220 / 230 / 240 V

85_02_03_0002

ENGLISH

WWW.STIEBEL-ELTRON-USA.COM DHC-E | 9

INSTALLATION

TECHNICAL DATA

10.3 Maximum temperature increase above ambient water temperature

Warm water ﬂ ow rate [ GPM ]

Warm water outlet temperature 104 °F

Cold water inlet temperature °F 39 50 59 68 77 86 95 104 113 122 131

DHC-E 8/10

5.4 kW @ 208 V 0.57 0.68 0.82 1.02 1.36 2.04 4.09 - - - -

7.2 kW @ 240 V 0.76 0.91 1.09 1.36 1.82 2.72 5.45 - - - -

7.2 kW @ 208 V 0.76 0.91 1.09 1.36 1.82 2.72 5.45 - - - -

9.6 kW @ 240 V 1.01 1.21 1.45 1.82 2.42 3.63 6.61 - - - -

DHC-E 12

9 kW @ 208 V 0.95 1.14 1.36 1.70 2.27 3.23 6.47 - - - -

12 kW @ 240 V 1.26 1.51 1.82 2.27 3.03 4.31 6.61 - - - -

Warm water outlet temperature 113 °F

Cold water inlet temperature °F 39 50 59 68 77 86 95 104 113 122 131

DHC-E 8/10

5.4 kW @ 208 V 0.50 0.58 0.68 0.82 1.02 1.36 2.04 4.09 - - -

7.2 kW @ 240 V 0.66 0.78 0.91 1.09 1.36 1.82 2.72 5.45 - - -

7.2 kW @ 208 V 0.66 0.78 0.91 1.09 1.36 1.82 2.72 5.45 - - -

9.6 kW @ 240 V 0.89 1.04 1.21 1.45 1.82 2.42 3.63 6.61 - - -

DHC-E 12

9 kW @ 208 V 0.83 0.97 1.14 1.36 1.70 2.16 3.23 6.47 - - -

12 kW @ 240 V 1.11 1.30 1.51 1.82 2.27 2.88 4.31 6.61 - - -

Warm water outlet temperature 140 °F

Cold water inlet temperature °F 39 50 59 68 77 86 95 104 113 122 131

DHC-E 8/10

5.4 kW @ 208 V 0.36 0.41 0.45 0.51 0.58 0.68 0.82 1.02 1.36 2.04 4.09

7.2 kW @ 240 V 0.49 0.54 0.61 0.68 0.78 0.91 1.09 1.36 1.82 2.72 5.45

7.2 kW @ 208 V 0.49 0.54 0.61 0.68 0.78 0.91 1.09 1.36 1.82 2.72 5.45

9.6 kW @ 240 V 0.65 0.73 0.81 0.91 1.04 1.21 1.45 1.82 2.42 3.63 6.61

DHC-E 12

9 kW @ 208 V 0.61 0.68 0.76 0.85 0.97 1.08 1.29 1.62 2.16 3.23 6.47

12 kW @ 240 V 0.81 0.91 1.01 1.14 1.30 1.44 1.73 2.16 2.88 4.31 6.61

Warm water ﬂ ow rate [ l/min ]

Warm water outlet temperature 40 °C

Cold water inlet temperature °C 4 10 15 20 25 30 35 40 45 50 55

DHC-E 8/10

5.4 kW @ 208 V 2.15 2.58 3.09 3.87 5.16 7.73 15.47 - - - -

7.2 kW @ 240 V 2.86 3.44 4.12 5.16 6.87 10.31 20.62 - - - -

7.2 kW @ 208 V 2.86 3.44 4.12 5.16 6.87 10.31 20.62 - - - -

9.6 kW @ 240 V 3.82 4.58 5.50 6.87 9.16 13.75 25.00 - - - -

DHC-E 12

9 kW @ 208 V 3.58 4.30 5.16 6.44 8.59 12.24 24.49 - - - -

12 kW @ 240 V 4.77 5.73 6.87 8.59 11.46 16.32 25.00 - - - -

Warm water outlet temperature 45 °C

Cold water inlet temperature °C 4 10 1 20 25 30 35 40 45 50 55

DHC-E 8/10

5.4 kW @ 208 V 1.89 2.21 2.58 3.09 3.87 5.16 7.73 15.47 - - -

7.2 kW @ 240 V 2.51 2.95 3.44 4.12 5.16 6.87 10.31 20.62 - - -

7.2 kW @ 208 V 2.51 2.95 3.44 4.12 5.16 6.87 10.31 20.62 - - -

9.6 kW @ 240 V 3.35 3.93 4.58 5.50 6.87 9.16 13.75 25.00 - - -

DHC-E 12

9 kW @ 208 V 3.14 3.68 4.30 5.16 6.44 8.16 12.24 24.49 - - -

12 kW @ 240 V 4.19 4.91 5.73 6.87 8.59 10.88 16.32 25.00 - - -

Warm water outlet temperature 60 °C

Cold water inlet temperature °C 4 10 15 20 25 30 35 40 45 50 55

DHC-E 8/10

5.4 kW @ 208 V 1.38 1.55 1.72 1.93 2.21 2.58 3.09 3.87 5.16 7.73 15.47

7.2 kW @ 240 V 1.84 2.06 2.29 2.58 2.95 3.44 4.12 5.16 6.87 10.31 20.62

7.2 kW @ 208 V 1.84 2.06 2.29 2.58 2.95 3.44 4.12 5.16 6.87 10.31 20.62

9.6 kW @ 240 V 2.45 2.75 3.05 3.44 3.93 4.58 5.50 6.87 9.16 13.75 25.00

DHC-E 12

9 kW @ 208 V 2.30 2.58 2.86 3.22 3.68 4.08 4.90 6.12 8.16 12.24 24.49

12 kW @ 240 V 3.07 3.44 3.82 4.30 4.91 5.44 6.53 8.16 10.88 16.32 25.00

10 | DHC-E WWW.STIEBEL-ELTRON-USA.COM

INSTALLATION

SPARE PARTS

10.4 Data table

DHC-E 8/10

DHC-E 12

Part number 224201 230628

Phase 1 1 1 1 1 1 1 1 1 1 1 1

Coding plug Position 1 1 1 1 2 2 2 2 - - - -

Voltage V 208 220 230 240 208 220 230 240 208 220 230 240

Frequency Hz 50 / 60 50 / 60 50 / 60 50 / 60 50 / 60 50 / 60 50 / 60 50 / 60 50 / 60 50 / 60 50 / 60 50 / 60

Output power kW 5.4 6.0 6.6 7.2 7.2 8.1 8.8 9.6 9 10 11 12

Amperage A 28 30 31 32 35 37 39 40 44 46 48 50

Min. recommended circuit breaker

(DP) A 30 40 40 40 35 40 40 40 50 50 50 50

Min. recommended wire size

(copper) AWG COPPER 8 8 8 8 8 8 8 8 6 6 6 6

Protection level according to IP 24 IP 24

Min. water flow to activate appliance GPM / l/min 0.37 / 1.4 0.37 / 1.4

Max. inlet water temperature °F / °C 131 / 55 131 / 55

Nominal water volume GAL / l 0.13 / 0.5 0.13 / 0.5

Working pressure max. PSI / bar / MPa 150 / 10 / 1 150 / 10 / 1

Tested to pressure PSI / bar / MPa 300 / 20 / 2 300 / 20 / 2

Weight lbs. / kg 5.9 / 2.7 5.9 / 2.7

Water connections 1/2“ NPT 1/2“ NPT

DHC-E 8/10 is a single unit that is switchable at installation via jumper for out put at 7.2 kW (Stage 1) or 9.6 kW (Stage 2).

This is our recommendation for overcurrent protection sized at 100% of load. Check local codes for compliance if necessary.

Tankless water heaters are considered a non-continuous load.

Copper must be used. Conductors should be sized to maintain a voltage drop of less than 3% under load.

11. Spare parts

987

26_02_02_1091

No. No. Spare part DHC-E 8/10 DHC-E 12

1 Heating system 292575 292576

2 Safety thermal cut out 286369 286369

3 Electronic control appliance 291851 291852

4 Coding plug 283455 ---

5 Back panel 292578 292578

6 Flow sensor DFE 286461 286461

7 Cold water connection 291699 291699

8 Filter screen 252430 252430

9 Hot water connection 278634 278634

10 Plastic cover 292577 292577

11 Wiring block 279998 279998

12 Axis connection plug 254312 254312

13 Electronic temperature control 286359 286359

14 Temperature adjustment knob 254307 254307

15 Outlet temperature sensor 280677 280677

WWW.STIEBEL-ELTRON-USA.COM DHC-E | 11

ENGLISH

WARRANTY | ENVIRONMENT AND RECYCLING

TANKLESS ELECTRIC DOMESTIC HOT WATER HEATERS

All Mini

™

, DHC, DHC-E, Tempra®, & Tempra® Plus Models

LIMITED WARRANTY

Subject to the terms and conditions set forth in this limited

warranty, Stiebel Eltron, Inc. (the “Manufacturer”) hereby

warrants to the original purchaser (the “Owner”) that each

Tankless Electric Domestic Hot Water Heater (the “Heater”)

shall not (i) leak due to defects in the Manufacturer’s

materials or workmanship for a period of seven (7) years

from the date of purchase or (ii) fail due to defects in the

Manufacturer’s materials or workmanship for a period of

three (3) years from the date of purchase. As Owner’s sole

and exclusive remedy for breach of the above warranty,

Manufacturer shall, at the Manufacturer’s discretion,

send replacement parts for local repair; retrieve the unit

for factory repair, or replace the defective Heater with a

replacement unit with comparable operating features.

Manufacturer’s maximum liability under all circumstances

shall be limited to the Owner’s purchase price for the

Heater.

This limited warranty shall be the exclusive warranty

made by the Manufacturer and is made in lieu of all other

warranties, express or implied, whether written or oral,

including, but not limited to warranties of merchantability

and ﬁ tness for a particular purpose. Manufacturer shall

not be liable for incidental, consequential or contingent

damages or expenses arising directly or indirectly from any

defect in the Heater or the use of the Heater. Manufacturer

shall not be liable for any water damage or other damage

to property of Owner arising, directly or indirectly,

from any defect in the Heater or the use of the Heater.

Manufacturer alone is authorized to make all warranties

on Manufacturer’s behalf and no statement, warranty or

guarantee made by any other party shall be binding on

Manufacturer.

Manufacturer shall not be liable for any damage

whatsoever relating to or caused by:

1. any misuse or neglect of the Heater, any accident to

the Heater, any alteration of the Heater, or any other

unintended use;

2. acts of God and circumstances over

which Manufacturer has no control;

3. installation of the Heater other than as directed by

Manufacturer and other than in accordance with

applicable building codes;

4. failure to maintain the Heater or to operate the Heater

in accordance with the Manufacturer’s speciﬁ cations;

5. operation of the Heater under ﬂ uctuating water

pressure or in the event the Heater is supplied with

non-potable water, for any duration;

6. improper installation and/or improper materials used

by any installer and not relating to defects in parts or

workmanship of Manufacturer;

7. moving the Heater from its original place of installation;

8. exposure to freezing conditions;

9. water quality issues such as corrosive water, hard water,

and water contaminated with pollutants or additives;

Should owner wish to return the Heater to manufacturer

for repair or replacement under this warranty, Owner

must ﬁ rst secure written authorization from Manufacturer.

Owner shall demonstrate proof of purchase, including a

purchase date, and shall be responsible for all removal

and transportation costs. If Owner cannot demonstrate a

purchase date this warranty shall be limited to the period

beginning from the date of manufacture stamped on the

Heater. Manufacturer reserves the right to deny warranty

coverage upon Manufacturer’s examination of Heater.

This warranty is restricted to the Owner and cannot be

assigned.

Some States and Provinces do not allow the exclusion

or limitation of certain warranties. In such cases, the

limitations set forth herein may not apply to the Owner. In

such cases this warranty shall be limited to the shortest

period and lowest damage amounts allowed by law. This

warranty gives you speciﬁ c legal rights and you may also

have other rights which vary from State to State or Province

to Province.

Owner shall be responsible for all labor and other charges

incurred in the removal or repair of the Heater in the ﬁ eld.

Please also note that the Heater must be installed in such a

manner that if any leak does occur, the ﬂ ow of water from

any leak will not damage the area in which it is installed.

Environment and recycling

Please help us protect the environment. Dispose of the appliance

and its packaging in accordance with national regulations.

12. Warranty

Page is loading ...

20 | DHC-E WWW.STIEBEL-ELTRON.COM

INSTALACIÓN

PIEZAS DE RECAMBIO

10.4 Tabla de especiﬁ caciones

DHC-E 8/10

DHC-E 12

224201 230628

Fase 1 1 1 1 1 1 1 1 1 1 1 1

Tensión V 1 1 1 1 2 2 2 2 - - - -

Frecuencia Hz 208 220 230 240 208 220 230 240 208 220 230 240

Enchufe de codificación Posición 50 / 60 50 / 60 50 / 60 50 / 60 50 / 60 50 / 60 50 / 60 50 / 60 50 / 60 50 / 60 50 / 60 50 / 60

Potencia de funcionamiento kW 5.4 6.0 6.6 7.2 7.2 8.1 8.8 9.6 9 10 11 12

Corriente nominal A 28 30 31 32 35 37 39 40 44 46 48 50

Protección mín. por fusible A 30 40 40 40 35 40 40 40 50 50 50 50

Sección transversal recomendada AWG Cobre 8 8 8 8 8 8 8 8 6 6 6 6

Tipo de protección según 0.37 / 1.4 0.37 / 1.4

Sección transversal recomendada mm² Cobre IP 24 IP 24

Caudal ON GPM / l/min 131 / 55 131 / 55

Capacidad nominal GAL / l 0.13 / 0.5 0.13 / 0.5

Presión máx. admisible PSI / bar / MPa 150 / 10 / 1 150 / 10 / 1

Presión de ensayo PSI / bar / MPa 300 / 20 / 2 300 / 20 / 2

Peso lbs Kg 5.9 / 2.7 5.9 / 2.7

Conexión de agua 1/2“ NPT 1/2“ NPT

DHC-E 8/10 is a single unit that is switchable at installation via jumper for out put at 7.2 kW (Stage 1) or 9.6 kW (Stage 2).

This is our recommendation for overcurrent protection sized at 100% of load. Check local codes for compliance if necessary.

Tankless water heaters are considered a non-continuous load.

Copper must be used. Conductors should be sized to maintain a voltage drop of less than 3% under load.

11. Piezas de recambio

987

26_02_02_1091

Nº Piezas de recambio DHC-E 8/10 DHC-E 12

1 Sistema de calefacción 292275 292276

2 Limitador de temperatura de seguridad 286369 286369

3 Grupo electrónico 291851 291852

4 Enchufe de codificación 283455 283455

5 Pared posterior de la carcasa 292578 292578

6 Caudalímetro (DFE) 286461 286461

7 Racor de conexión del agua fría 291699 291699

8 Filtro 252430 252430

9 Racor de conexión del agua caliente 278634 278634

10 Tapa de la carcasa 292577 292577

11 Terminal de conexión eléctrica 279998 279998

12 Eje de quita y pon 254312 254312

13 Pletina (transmisor de valor de referencia) 286359 286359

14 Botón del regulador de temperatura 254307 254307

15 Sensor de temperatura (NTC) 280677 280677

Page is loading ...

Deutschland

STIEBEL ELTRON GmbH & Co. KG

Dr.-Stiebel-Straße | 37603 Holzminden

Tel. 05531 702-0 | Fax 05531 702-480

[email protected]

www.stiebel-eltron.de

Irrtum und technische Änderungen vorbehalten! | Subject to errors and technical changes! | Sous réserve

d‘erreurs et de modiﬁcations techniques! | Onder voorbehoud van vergissingen en technische wijzigingen! |

Salvo error o modiﬁcación técnica! | Rätt till misstag och tekniska ändringar förbehålls! | Excepto erro ou

alteração técnica | Zastrzeżone zmiany techniczne i ewentualne błędy | Omyly a technické změny jsou

vyhrazeny! | A muszaki változtatások és tévedések jogát fenntartjuk! |

Отсутствие ошибок не

гарантируется. Возможны технические изменения.

| Chyby a technické zmeny sú vyhradené! Stand 8643

Austria

STIEBEL ELTRON Ges.m.b.H.

Eferdinger Str. 73 | 4600 Wels

Tel. 07242 47367-0 | Fax 07242 47367-42

[email protected]

www.stiebel-eltron.at

Belgium

STIEBEL ELTRON bvba/sprl

't Hofveld 6 - D1 | 1702 Groot-Bijgaarden

Tel. 02 42322-22 | Fax 02 42322-12

[email protected]

www.stiebel-eltron.be

Czech Republic

STIEBEL ELTRON spol. s r.o.

K Hájům 946 | 155 00 Praha 5 - Stodůlky

Tel. 251116-111 | Fax 235512-122

[email protected]

www.stiebel-eltron.cz

Denmark

Pettinaroli A/S

Mandal Allé 21 | 5500 Middelfart

Tel. 06341 666-6 | Fax 06341 666-0

[email protected]

www.stiebel-eltron.dk

Finland

Insinööritoimisto Olli Andersson Oy

Kapinakuja 1 | 04600 Mäntsälä

Tel. 020 720-9988 | Fax 020 720-9989

info@stiebel-eltron.ﬁ

www.stiebel-eltron.ﬁ

France

STIEBEL ELTRON SAS

7-9, rue des Selliers

B.P 85107 | 57073 Metz-Cédex 3

Tel. 0387 7438-88 | Fax 0387 7468-26

[email protected]

www.stiebel-eltron.fr

Hungary

STIEBEL ELTRON Kft.

Pacsirtamező u. 41 | 1036 Budapest

Tel. 01 250-6055 | Fax 01 368-8097

[email protected]

www.stiebel-eltron.hu

Japan

NIHON STIEBEL Co. Ltd.

Ebara building 3F

2-9-3 Hamamatsu-cho

Minato-Ku | 105-0013 Tokyo

Tel. 03 34364662 | Fax 03 34594365

[email protected]

www.nihonstiebel.co.jp

Netherlands

STIEBEL ELTRON Nederland B.V.

Daviottenweg 36

5222 BH 's-Hertogenbosch

Tel. 073 623-0000 | Fax 073 623-1141

[email protected]

www.stiebel-eltron.nl

Poland

STIEBEL ELTRON Polska Sp. z o.o.

ul. Instalatorów 9 | 02-237 Warszawa

Tel. 022 60920-30 | Fax 022 60920-29

[email protected]

www.stiebel-eltron.com.pl

Russia

STIEBEL ELTRON LLC RUSSIA

Urzhumskaya street 4,

building 2 | 129343 Moscow

Tel. 0495 7753889 | Fax 0495 7753887

[email protected]

www.stiebel-eltron.ru

Slovakia

TATRAMAT - ohrievače vody, s.r.o.

Hlavná 1 | 058 01 Poprad

Tel. 052 7127-125 | Fax 052 7127-148

[email protected]

www.stiebel-eltron.sk

Sweden

STENERGY

Vasagatan 14 | 545 30 Töreboda

Sales:

Tel. 0506 105-10 | [email protected]

Technique & Service:

Tel. 0150 54200 | [email protected]

www.stiebel-eltron.se

Switzerland

STIEBEL ELTRON AG

Netzibodenstr. 23 c | 4133 Pratteln

Tel. 061 81693-33 | Fax 061 81693-44

[email protected]

www.stiebel-eltron.ch

Thailand

STIEBEL ELTRON Asia Ltd.

469 Moo 2 Tambol Klong-Jik

Amphur Bangpa-In | 13160 Ayutthaya

Tel. 035 220088 | Fax 035 221188

[email protected]

www.stiebeleltronasia.com

United Kingdom and Ireland

STIEBEL ELTRON UK Ltd.

Unit 12 Stadium Court

Stadium Road | CH62 3RP Bromborough

Tel. 0151 346-2300 | Fax 0151 334-2913

[email protected]

www.stiebel-eltron.co.uk

United States of America

STIEBEL ELTRON, Inc.

17 West Street | West Hatﬁeld MA ''

Tel. 0413 247-3380 | Fax 0413 247-3369

Toll-free 800.582.8423

[email protected]

www.stiebel-eltron-usa.com

A 291850-38924-9058

4<AMHCMN=jbifaa>

STIEBEL ELTRON DHC-E 8/10 Installation guide

Brand: STIEBEL ELTRON

Model: DHC-E 8/10

Category: Space heaters

Type: Installation guide

This manual is also suitable for

DHC-E 12

Download PDF

report

in other languages

français: STIEBEL ELTRON DHC-E 8/10 Guide d'installation
español: STIEBEL ELTRON DHC-E 8/10 Guía de instalación

STIEBEL ELTRON DHC-E 8/10 Installation guide

This manual is also suitable for

STIEBEL ELTRON DHC-E 8/10 Installation guide

in other languages

Related papers

Other documents