Cutout Dimensions (in inches)
Built-In Downdraft Cooktops Dimensions (in inches)
Receptacle Location
Install an approved junction box within shaded area
shown in diagram. Junction box must be at least
10-1/2" below top of cabinet.
Cabinet Dimensions (in inches)
40
Long
20
9
4
10-1/2
16
C
L
Cabinet Dimensions (in inches)
Wall Installation
Wall installations require 25" countertop depth. When cabinet
is
flush
against the wall, the fan housing can be rotated to the
horizontal
position for direct venting through rear wall. Make a
countertop
cutout in the range cabinet according to unit dimensions
and installatio
n
type. Duct hole is positioned in back of cabinet for
through-the-wall ducting. Requires special offset adapter JXRW89.
Peninsula or Island Installation
For peninsula/islands a minimum 26" countertop depth is suggested.
Blower should be in vertical position. Island or peninsula cabinets
may require adjustment in cutout depth and/or location within the
width dimensions. Duct hole is positioned in bottom of cabinet for
island or peninsula installation.
Slab Installation
For peninsula or island installation and rear wall ducting,
6" PVC
duct or locally approved piping should be used if installing
under a poured concrete slab.
Installation Information:
Before installing, consult installation
instructions packed with product for current dimensional data.
Note:
Electrical cable is not supplied with unit.
These cooktops are U.L. approved for indoor use only.
For answers to your Monogram
,
®
GE Profi le
™
or
GE
®
appliance questions, visit our website at
GEAppliances.com or call GE Answer Center
®
service, 800.626.2000.
R
Listed by
Underwriters
Laboratories
KW Rating
240V
8.8
208V
6.7
21-7/8
6
22
6"
Dia.
20-1/2 28-3/4
29-7/8
6
Cooktop Dimensions (in inches)
25
1-7/8"
MIN. Required*
20-5/8
Cut-out Dimensions (in inches)
28-7/8
*U.L. Requirement.
Note: A 6" minimum spacing to adjacent side wall is required
JP989SD – GE Profile
™
30" Downdraft Electric Cooktop
Specification Revised 11/04
220973
Venting Options
Inside Wall
Through Roof
Direct to Outside
Straight Duct
Between the Floor Joists
Through the Cabinet Toe Space
Note:
Ductwork must be vented to outside. Do not vent into a wall, ceiling, crawlspace, attic or
any concealed space. Always use an appropriate roof or wall cap with damper.
Laundry-type
wall caps should never be used.
For maximum efficiency use the shortest and straightest
duct run possible, with as few fittings as possible. For satis factory performance the duct run
should not exceed 100 feet equivalent length. Refer to the table of equivalent lengths (shown
in installation instructions) for various duct configurations.
Downward Venting (in inches)
Rear Wall Venting (in inches)
Installing the Ductwork
Use galvanized or aluminum duct in 6" round or 3-1/4" x 10" size, or combination of both.
PVC
duct or locally approved piping should be used if installing under a poured concrete
slab.
Local building code must be followed in specifying type and schedule of all duct used.
Venting Options
For answers to your Monogram
,
®
GE Profi le
™
or
GE
®
appliance questions, visit our website at
GEAppliances.com or call GE Answer Center
®
service, 800.626.2000.
R
Listed by
Underwriters
Laboratories
Venting Options
Inside Wall
Through Roof
Direct to Outside
Straight Duct
Between the Floor Joists
Through the Cabinet Toe Space
Venting Options
Inside Wall
Through Roof
Direct to Outside
Straight Duct
Between the Floor Joists
Through the Cabinet Toe Space
9-1/8
10-1/8
18-3/4
6-1/8
Rear wall venting (in inches)
Downward venting
(in inches)
9-1/8
10-1/8
18-3/4
6-1/8
Rear wall venting (in inches)
Downward venting
(in inches)
Specification Revised 11/04
220973
JP989SD – GE Profile
™
30" Downdraft Electric Cooktop
Features and Benefits
• Downdraft exhaust – Powerful exhaust system effectively pulls smoke and steam out
of the kitchen
• Ceramic glass cooktop – A smooth cooktop surface makes cleaning quick and easy
• Ribbon heating elements – Provides powerful heat beneath the smooth glass surface
to ensure even heat and fast warm-up times
• Bridge-element – Combines three of the cooktop elements into one large cooking area,
ideal for oversized cooking pans
• Dual size ribbon element – Offers a convenient choice of using a 6" or 9" heating
element, depending on the size of the pan
• Three speed downdraft fan – Powerful three speed exhaust system effectively pulls
smoke and vapors out of the kitchen
• Frameless design – A smooth and seamless cooktop surface makes cleaning quick
and easy
• Model JP989SDSS – Stainless steel
L
O
O
F
F
H
I
1
2
3
4
5
6
7
8
9
L
O
O
F
F
H
I
1
2
3
4
5
6
7
8
9
B
R
I
D
G
E
L
O
O
F
F
H
I
1
2
3
4
5
6
7
8
9
C
O
I
L
S
I
Z
E
L
O
O
F
F
H
I
1
2
3
4
5
6
7
8
9
U
N
I
T
O
N
H
O
T
H
O
T
JP989SD.EPS
L
O
O
F
F
M
E
D
Specification Revised 11/04
220973
JP989SD – GE Profile
™
30" Downdraft Electric Cooktop
/
