PAC BKHONK840 User manual

Brand: PAC

Model: BKHONK840

Category: Car kits

Type: User manual

This manual is also suitable for

HONK840

PAC BKHONK840 is a mounting kit designed for seamless integration of aftermarket stereos into 2013-2015 Honda Civics. It facilitates the removal of the factory radio/climate control panel, allowing for the installation of a new head unit. The kit includes a main frame, trim pieces, metal retaining clips, and screws for a secure and professional-looking finish. Whether you prefer single or double DIN installations, the PAC BKHONK840 provides a tailored solution to enhance your in-car audio experience.

HONK840 Mounting Kit

Honda

2013-15 CIVIC

VEHICLE APPLICATIONS

TECH Ver. 6/16 PRINT Ver. 8/13

www.aampglobal.com www.aius.net

2500 East Francis Street Ontario, CA 91761, U.S.A.

Sales: (800) 477-2267

Intl: (727) 572-9255

Support: 888-228-5560

iHONK840

2 7

KIT PREPARATION

Fig A

REMOVE ALL

4 SHADED BRACKETS

NOTES:

DASH DISASSEMBLY INSTRUCTIONS

1. Open pocket below radio and remove (2) Phillips/8mm screws. Remove pocket.

2. Remove (2) Phillips screws located below the HVAC.

3. Remove the (2) screws holding the factory radio mounting brackets to the sub dash.

4. Carefully remove the factory radio/climate control panel including the hazard button

and air vent.

5. Unplug all harnesses and remove.

013 HONDA CIVIC

BEZEL ASSEMBLY INSTRUCTIONS

1. Remove the (3) Phillips screws securing the air vent to the rear of the factory

radio/climate control assembly and attach to the same location on the rear of the

HONK840 main frame (Do Not Overtighten).

2. Remove the (2) Phillips screws securing the hazard light switch to the rear of the

factory radio/climate control assembly and attach to the same location on the rear of

the HONK840 main frame (Do Not Overtighten).

3. Remove the (4) Phillips screws securing the climate control module to the rear of the

factory radio/climate control assembly and attach to the same location on the rear of

the HONK840 main frame (Do Not Overtighten).

4. Remove the (3) Phillips screws securing the lower trim panel to the rear of the bottom

of factory radio/climate control assembly and attach to the same location on the rear

of the HONK840 main frame (Do Not Overtighten).

5. Install the (6) Metal retaining clips supplied, to the posts on the HONK840 main frame.

6. Remove (4) Phillips screws holding the radio to the OEM panel,

save for radio kit assembly.

Important instructions on HONK840 main frame installation.

When installing the HONK840 mainframe into the dash you must first line-up

and guide the driver side dash clip locator post into its location.

Then you can snap in the other sides if the dash kit.

6 3

INSTALL CLIPS HERE ON BOTH

LEFT & RIGHT BRACKETS

(flat side of the clip on the bottom)

INSTALL CLIPS HERE ON BOTH

LEFT & RIGHT BRACKETS

(flat side of the clip on the bottom)

4 5

SINGLE ISO INSTALLATIONS DOUBLE DIN INSTALLATIONS

Fig B

Fig C

1. This kit is an (ISO) mounting kit only.

2. The mounting sleeve of your new radio and trim ring cannot be used when

ISO mounting an aftermarket radio. Your radio must have a removable trim ring.

3. Insert pocket into lower section of kit from rear & lock into slots of mounting brackets.

4. Insert trim into the main frame.

5. Install using 4 screws left over from the OEM panel mount the left and right mounting

brackets to rear of main frame (Do Not Overtighten).

6. Insert ISO mountable radio between ISO mount brackets and loosely attach to sides

of radio using screws provided with radio when possible or screws supplied with kit.

7. Slide radio forward or backward for desired look and tighten screws.

8. Install clips provided with kit to lower bracket location. Once kit is installed use the

5/8 screws also provided with the kit to securely mount the brackets to the sub-dash.

1. Insert trim into main frame.

2. Install using 4 screws left over from the OEM panel mount the brackets L&R into

rear of the main frame (Do Not Overtighten).

3. Insert ISO mountable radio between ISO mount brackets and loosely attach to sides

of radio using screws provided with radio when possible or hardware included with kit.

4. Slide radio component forward or backward for desired look and tighten screws.

5. Install clips provided with kit to lower bracket location. Once kit is installed use the

5/8 screws also provided with the kit to securely mount the brackets to the sub-dash.

REMOVE SHADED TABS

ON BOTH LEFT

& RGHT BRACKETS

PAC BKHONK840 User manual

Brand: PAC

Model: BKHONK840

Category: Car kits

Type: User manual

This manual is also suitable for

HONK840

Download PDF

report

PAC BKHONK840 User manual

This manual is also suitable for

PAC BKHONK840 User manual

Related papers

Other documents