SWITCHING AC ADAPTER (12VDC)
PWA-65AWD1 User’s Guide
CONTEC CO., LTD.
Thank you for purchasing this product.
This product is the AC adapter for input: 100 - 240VAC and output: +12VDC 5.417A (Max.).
With the manual of your
product supplied by Contec, confirm that this adapter supports your model. (It is not possible to use it excluding the target
model.)
Package Contents
- AC adapter …1 - Warranty Certificate …1
- AC power cable (100VAC, 3pin) *1*2 …1 - Serial Number Label…1
- User’s Guide (this booklet) …1
*1 Do not use the AC power cable other than in Japan as it is only available with the 100VAC.
In the case that the voltage that this cable uses do not match you need to prepare other cable particularly.
*2 Do not use this AC power cable with any devices except for a bundled AC adapter.
Usage environment
It is expected that you will use this product in a comparatively good environment.
If you will use it in a harsh environment or if you require a long service life from it, we ask that you separately prepare a
power supply that fits your application.
If the AC adapter fails, CONTEC will replace it with an equivalent product (a charge may be applied to the
replacement).
Also, note that we cannot provide analyses of failure causes.
Disposal
When disposing of the product, follow the disposal procedures stipulated under the relevant laws and municipal
ordinances.
Storage
When storing this product, keep it in its original packing form.
(1) Wrap it in the packing material, and then put it in the box.
(2) Store the package at room temperature at a place free from direct sunlight, moisture, shock, vibration, magnetism, and
static electricity.
Safety Information
This document provides safety information using the following symbols to prevent accidents resulting in injury or death
and the destruction of equipment and resources. Understand the meanings of these labels to operate the equipment
safely.
DANGER indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
WARNING indicates a potentially hazardous situation which, if not avoided, could result in death or seriou s injury.
CAUTION indicates a pot enti all y hazardou s situatio n which, if not avo ided, may result in minor or mo derat e injury or
in pro pert y damage.
Handling Precautions
Indicates dos and don'ts that are assumed to result in possible death or serious injury if they are inappropriately handled
ignoring this icon.
- Do not use the product in locations exposed to a flammable or corrosive gas. It may cause explosion, fire, electrical
shock, or malfunction.
- If you sense abnormality (smoke, odor, or noise), immediately unplug the power cord from the wall outlet and
contact the CONTEC sales representative or sales office.
- To avoid electrocution do not use the product with a wet hand.
- Be sure to connect the product to the stipulated power supply voltage. Connecting to a different voltage might cause a
fire or electrical shock.
- Do not use the product with the other power device. It may cause fire or malfunction.
- When the cable or main body is damaged, stop using and repair it immediately. Using it as it is may cause fire,
electrical shock or malfunction.
- Never disassemble or modify the product or replace its parts in order to prevent electrical shock, fire, or malfunction.
CONTEC reserves the right to refuse servicing the product modified by the user. When any part of the product needs
to be replaced at the expiration of its life or due to breakdown, please contact the CONTEC sales representative or
sales office.
- Use the product with the specified models by the CONTEC. Not doing so may cause fire or malfunction.
- Use the product in the specified operating condition (temperature and humidity)
Indicates dos and don'ts that are assumed to result in possible injury or property damage if they are inappropriately
handled ignoring this icon.
- Do not use or store the product in a location exposed to extremely high or low temperature or susceptible to a rapid
temperature change. Example:
- Exposure to direct sun - In the vicinity of a heat source
- When unplugging the cable, hold the plug. Holding and pulling the cable itself can cause a failure such as
discontinuity.
- To clean the product, wipe it gently with soft cloth damp with either water or mild detergent.
Do not use chemicals or a volatile solvent, such as benzene and thinner, to prevent peeling or discoloration of the
paint.
- When transporting the product, provide adequate measures to protect it from vibration or shock.
- No part of this document may be copied or reproduced in any form by any means without prior written consent of
CONTEC CO., LTD.
- The information in this document is subject to change without notice.
- All relevant issues have been considered in the preparation of this document. Should you notice an omission or any
questionable item in this document, please feel free to notify CONTEC CO., LTD.
- Regardless of the foregoing statement, CONTEC assumes no responsibility for any errors that may appear in this
document or for results obtained by the user as a result of using this product.
Using method
- Make sure that the AC power cable is not plugged into a wall outlet.
- Connect the AC power cable to the main body of AC adapter connector (CN1).
- Connect the DC cable of AC adaptor with the DC power supply connector.
- Plug the AC power cable into a wall outlet.
* This product has no power switch. When turning off, unplug the AC power cable from the wall outlet.
Specifications
Requirement
Description
Power supply space
Rated input voltage
100VAC to 240VAC (continuous input), 50 to 60Hz
Permissible input voltage 90 - 264VAC (continuous input, Power consumption 60W or less)
Input current
2.0A RMS Max. (AC IN 100VAC)
Rated output voltage
+12VDC±5%
Rated output current
5.417A (Max.)
Hold up time 6ms or less (115VAC)
Dielectric strength
(between Input P and S)
3.0kVAC fo r six second
Insulation resistance
(between P and S)
Greater than 50MΩ (500VDC)
Environmental specs
Surrounding temperature
Operating: 0 to +40 ºC
Storage: -25 to +60 ºC
Surrounding humidity
Operating: 10 - 85%RH (No condensation)
Storage: 10 - 95%RH (No condensation)
Floating dust particles
Not to be excessive
Corrosive gases None
Standard
(Excluding AC power cable)
PSE, FCC, UL/cUL, CE, TUV-GS, CCC, BSMI, KC, RCM, CB,
RoHS, China RoHS
Others
Cable length
AC power cable: 2m, DC cable: 1.5m
External dimensions (mm)
68(W) x 153(D) x 35(H) (not include projection of cable)
Weight
Main body: 650g, AC power cable: 180g
MTBF *1*2 100,000H (temperature 25 ºC)
Life *1*2
6.3year (temperature 40°C, At load 2.55A, when connected BX-825 series)
17.8year (temperature 25°C, At load 2.55A, when connected BX-825 series)
*1 Note that MTBF and life is only referential value, not guaranteed value.
*2 Referential value when used with a specified PC.
Physical dimensions
AC power cable
(100VAC
, 3pin)
AC
adapter User'
s
Guide
(this
document)
Warrant
y
Certificate
Serial Number Label
DANGER
WARNING
CAUTION
WAR NING
CAUTION
0.8±0.3
115±0.5
30.5±0.5
CN1
[mm]
1200±30
13.9±0.5
51.5±0.5
[mm]
CONTEC CO., LTD.
3-9-31, Himesato, Nishiyodogawa-ku, Osaka 555-0025, Japan
https://www.contec.com/
No part of this document may be copied or reproduced in any form by any means
without prior written consent of CONTEC CO., LTD.
NA06038 (LYVS934) 10152019_rev4 [01262018] October 2019 Edition
With an optional bracket
Optional products
Bracket
- BX-BKT-PWA-02: AC adapter bracket for the box computer
(for setting the bracket to the side of the specified device)
- Specified product : BX-956SD-DCxxxxxx
How to set the AC adapter
Refer to the figure below when setting the AC adapter to the box computer.
- Make sure that the power of the computer is turned off when setting the adapter.
- Screw holes may be damaged if screws are tightened with a torque greater than the specified torque.
The specified tightening torque is 6 kgf⋅cm.
[mm]
16.2
53
(37)
150
140
121.4
Attachment bracket
Cable Tie
(to secure the AC adapter)
AC adapter
Washer assembled
screws (M3×10)
CAUTI
ON
-
1
-
2
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Contec PWA-84AWD1 Owner's manual
-
-
-
-
-
-
-
Contec POA200-20-2 Owner's manual
-
-