Pyle PSIB27X2 Owner's manual

Pyle
Brand
Pyle
Model
PSIB27X2
Type
Owner's manual

Pyle PSIB27X2 is a portable sound booth designed to provide soundproofing and reduce sound reflection. Its compact design makes it easy to set up and store, and it can be placed on a table or other flat surface.

The sound booth is made of high-density noise-absorbing acoustic foam, which helps to minimize unwanted noise and improve sound quality. It also features a zippered back panel that allows you to run cables through, so you can easily connect your microphone, headphones, or other audio equipment.

The Pyle PSIB27X2 is perfect for recording vocals, instruments, or podcasts.

Pyle PSIB27X2 is a portable sound booth designed to provide soundproofing and reduce sound reflection. Its compact design makes it easy to set up and store, and it can be placed on a table or other flat surface.

The sound booth is made of high-density noise-absorbing acoustic foam, which helps to minimize unwanted noise and improve sound quality. It also features a zippered back panel that allows you to run cables through, so you can easily connect your microphone, headphones, or other audio equipment.

The Pyle PSIB27X2 is perfect for recording vocals, instruments, or podcasts.

Handle: This side should be the top side
www.PyleUSA.com
PSIB27X2
2 Pcs. Sound Recording Booth Box
Studio Soundproofing Foam Shield Isolation Filter Cube
Note: Microphone and tripod are not included in the list
of contents.
The portable sound booth is used to provide sound
protection and to reduce sound reection. The booth can
be open and assembled in a short time. It could be placed
on the table. It is suitable for various kind of microphone
including vocal microphone, instrument microphone and
other recording microphone, etc.
Note: Please read this user’s manual carefully before using the sound booth. Any
mishandling of the product due to misunderstand of negligence of this manual may
lead to malfunction.
Installation Guide
1. Take all the contents from the package and make them properly placed
2. Pull the handle of the booth frame and make it properly structured, the side with
the handle should be in the top when you set up your booth.
3. Zip the back side of the frame.
This zip gap can be also used for the mic cable, add the
mic cable rstly if you want to let you mic cable go from
the back,the XLR female end should go inside normally
around 2ft.
www.PyleUSA.com
4. Put down the exible board and make it support the back side of the frame.
In order to make sure each foam to stay on the inner side well please follow the
below steps
5. Take out one of foam and insert it, aligning it with the top surface.
6. take out a second foam and insert it, aligning it with the right side surface.
7. Take out the third foam and insert it, aligning it with the left side surface
8. Take our the fourth foam and lay it against the back side surface.
This products can expose you to a chemical or group of checmicals, which
may include ”Di (2-ethylhexyl) phthalate (DEHP)” which is known in the
state of California to cause cancer, birth defects, or other reproductive
harm. For more info, go to https://www.p65warnings.ca.gov/.
www.PyleUSA.com
If you nd the top foam can’t stay well, you can use the double side glue sticker to
stick the top foam with the top side.
9. Then you can place your microphone with tripod base or round mic base inside,
connect your mic cable with microphone,install your pop lter on the stand then
start to record.
Features:
• Versatile Mic Recording & Sound Isolation Ability
• Portable and Compact Cube Design
• Ready to Record: Quick & Easy Setup
• Soundproong Studio Foam 'Wedgie' Acoustic Tiles
• Box-Style Engineered for Maximum Absorption/Isolation
• High-Density Noise-Absorbing Acoustic Foam
• Perfect for Studio Recording, Podcasts, Vocals, Singing, etc.
• Run Cables Through Rear Panel Zipper
• *Tripod Mount & Microphone not included
What's in the Box:
• (2) Sound Recording Booth Box • (8) Studio Foam
Technical Specs:
• Construction Material: Polyester
• Opened Dimensions (L x W x H): 12.2'' x 13.0'' x 13.3'' -inches
• Folded Dimensions (L x W x H): 25.2'' x 13.2'' x 2.4'' -inches
www.PyleUSA.com
Questions? Issues?
We are here to help!
Phone: (1) 718-535-1800
Email: suppor[email protected]om
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Pyle PSIB27X2 Owner's manual

Pyle
Brand
Pyle
Model
PSIB27X2
Type
Owner's manual

Pyle PSIB27X2 is a portable sound booth designed to provide soundproofing and reduce sound reflection. Its compact design makes it easy to set up and store, and it can be placed on a table or other flat surface.

The sound booth is made of high-density noise-absorbing acoustic foam, which helps to minimize unwanted noise and improve sound quality. It also features a zippered back panel that allows you to run cables through, so you can easily connect your microphone, headphones, or other audio equipment.

The Pyle PSIB27X2 is perfect for recording vocals, instruments, or podcasts.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents