Black & Decker KFBES500 User manual

Brand: Black & Decker

Model: KFBES500

Category: Power tools

Type: User manual

This manual is also suitable for

www.blackanddecker.co.uk

KFBES410

KFBES500

KFBES410

KFBES500

D E

KFBES500

Intended use

Your BLACK+DECKER jig saw KFBES410, KFBES500 has

been designed for sawing wood, plastics and metal. This tool

is intended for consumer use only.

Safety instructions

General power tool safety warnings

Warning! Read all safety warnings and all

instructions. Failure to follow the warnings and

instructions listed below may result in electric

shock, re and/or serious injury.

Save all warnings and instructions for future reference.

The term "power tool" in all of the warnings listed below

refers to your mains operated (corded) power tool or battery

operated (cordless) power tool.

1. Work area safety

a. Keep work area clean and well lit. Cluttered or dark

areas invite accidents.

b. Do not operate power tools in explosive atmospheres,

such as in the presence of ammable liquids, gases

or dust. Power tools create sparks which may ignite the

dust or fumes.

c. Keep children and bystanders away while operating a

power tool. Distractions can cause you to lose control.

2. Electrical safety

a. Power tool plugs must match the outlet. Never modify

the plug in any way. Do not use any adapter plugs

with earthed (grounded) power tools. Unmodied plugs

and matching outlets will reduce risk of electric shock.

ENGLISH

(Original instructions)

b. Avoid body contact with earthed or grounded

surfaces such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric shock

if your body is earthed or grounded.

c. Do not expose power tools to rain or wet conditions.

Water entering a power tool will increase the risk of

electric shock.

d. Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool. Keep

cord away from heat, oil, sharp edges or moving

parts. Damaged or entangled cords increase the risk of

electric shock.

e. When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use of a cord

suitable for outdoor use reduces the risk of electric shock.

f. If operating a power tool in a damp location is

unavoidable, use a residual current device (RCD)

protected supply. Use of an RCD reduces the risk of

electric shock.

3. Personal safety

a. Stay alert, watch what you are doing and use common

sense when operating a power tool. Do not use a

power tool while you are tired or under the inuence

of drugs, alcohol or medication. A moment of inattention

while operating power tools may result in serious personal

injury.

b. Use personal protective equipment. Always wear eye

protection. Protective equipment such as dust mask,

non-skid safety shoes, hard hat, or hearing protection

used for appropriate conditions will reduce personal

injuries.

c. Prevent unintentional starting. Ensure the switch is in

the off-position before connecting to power source

and/or battery pack, picking up or carrying the tool.

Carrying power tools with your nger on the switch or

energising power tools that have the switch on invites

accidents.

d. Remove any adjusting key or wrench before turning

the power tool on. A wrench or a key left attached to a

rotating part of the power tool may result in personal injury.

e. Do not overreach. Keep proper footing and balance at

all times. This enables better control of the power tool in

unexpected situations.

f. Dress properly. Do not wear loose clothing or

jewellery. Keep your hair, clothing and gloves away

from moving parts. Loose clothes, jewellery or long hair

can be caught in moving parts.

g. If devices are provided for the connection of dust

extraction and collection facilities, ensure these are

connected and properly used. Use of dust collection can

reduce dust-related hazards.

4. Power tool use and care

a. Do not force the power tool. Use the correct power

tool for your application. The correct power tool will do

the job better and safer at the rate for which it was

designed.

b. Do not use the power tool if the switch does not turn it

on and off. Any power tool that cannot be controlled with

the switch is dangerous and must be repaired.

c. Disconnect the plug from the power source and/or the

battery pack from the power tool before making any

adjustments, changing accessories, or storing power

tools. Such preventive safety measures reduce the risk of

starting the power tool accidentally.

d. Store idle power tools out of the reach of children and

do not allow persons unfamiliar with the power tool or

these instructions to operate the power tool. Power

tools are dangerous in the hands of untrained users.

e. Maintain power tools. Check for misalignment or

binding of moving parts, breakage of parts and any

other condition that may affect the power tools

operation. If damaged, have the power tool repaired

before use. Many accidents are caused by poorly

maintained power tools.

f. Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges are less

likely to bind and are easier to control.

g. Use the power tool, accessories and tool bits etc. in

accordance with these instructions, taking into

account the working conditions and the work to be

performed. Use of the power tool for operations different

from those intended could result in a hazardous situation.

5. Service

a. Have your power tool serviced by a qualied repair

person using only identical replacement parts. This

will ensure that the safety of the power tool is maintained.

Additional power tool safety warnings

Warning! Additional safety warnings for jigsaws

and reciprocating saws

u Hold power tool by insulated gripping surfaces, when

performing an operation where the cutting accessory

may contact hidden wiring or its own cord. Cutting

accessory contacting a “live” wire may make exposed

metal parts of the power tool “live” and could give the

operator an electric shock.

u Use clamps or another practical way to secure and

support the workpiece to a stable platform. Holding the

work by hand or against your body leaves it unstable and

may lead to loss of control.

ENGLISH

(Original instructions)

u Keep hands away from cutting area. Never reach

underneath the work piece any reason. Do not insert

ngers or thumb into the vicinity of the reciprocating blade

and blade clamp. Do not stabilize the saw by gripping the

shoe.

u Keep blades sharp. Dull or damaged blades may cause

the saw to swerve or stall under pressure. Always use the

appropriate type of saw blade for the workpiece material

and type of cut.

u When cutting pipe or conduit, make sure that they are

free from water, electrical wiring, etc.

u Do not touch the workpiece or the blade immediately

after operating the tool. They can become very hot.

u Be aware of hidden hazards, before cutting into walls,

oors or ceilings, check for the location of wiring and

pipes.

u The blade will continue to move after releasing the

switch. Always switch the tool off and wait for the saw

blade to come to a complete standstill before putting the

tool down.

Warning! Contact with, or inhalation of dusts arising from

cutting applications may endanger the health of the operator

and possible bystanders. Wear a dust mask specically

designed for protection against dust and fumes and ensure

that persons within or entering the work area are also

protected.

u The intended use is described in this instruction manual.

The use of any accessory or attachment or performance

of any operation with this tool other than those

recommended in this instruction manual may present a

risk of personal injury and/or damage to property.

Safety of others

u This appliance is not intended for use by persons

(including children) with reduced physical, sensory or

mental capabilities, or lack of experience and knowledge,

unless they have been given supervision or instruction

concerning use of the appliance by a person responsible

for their safety.

u Children should be supervised to ensure that they do not

play with the appliance.

Residual risks.

Additional residual risks may arise when using the tool which

may not be included in the enclosed safety warnings. These

risks can arise from misuse, prolonged use etc.

Even with the application of the relevant safety regulations

and the implementation of safety devices, certain residual

risks can not be avoided. These include:

u Injuries caused by touching any rotating/moving parts.

u Injuries caused when changing any parts, blades or

accessories.

u Injuries caused by prolonged use of a tool. When using

any tool for prolonged periods ensure you take regular

breaks.

u Impairment of hearing.

u Health hazards caused by breathing dust developed when

using your tool (example:- working with wood, especially

oak, beech and MDF.)

Vibration

The declared vibration emission values stated in the technical

data and the declaration of conformity have been measured

in accordance with a standard test method provided by

EN 60745 and may be used for comparing one tool with

another. The declared vibration emission value may also be

used in a preliminary assessment of exposure.

Warning! The vibration emission value during actual use of

the power tool can differ from the declared value depending

on the ways in which the tool is used. The vibration level may

increase above the level stated.

When assessing vibration exposure to determine safety

measures required by 2002/44/EC to protect persons regularly

using power tools in employment, an estimation of vibration

exposure should consider, the actual conditions of use and the

way the tool is used, including taking account of all parts of the

operating cycle such as the times when the tool is switched off

and when it is running idle in addition to the trigger time.

Labels on tool

The following pictograms are shown on the tool along with the

date code:

Warning! To reduce the risk of injury, the user

must read the instruction manual.

Electrical safety

This tool is double insulated; therefore no earth

wire is required. Always check that the power

supply corresponds to the voltage on the rating

plate.

u If the supply cord is damaged, it must be replaced by the

manufacturer or an authorised BLACK+DECKER Service

Centre in order to avoid a hazard.

Features

This tool includes some or all of the following features.

1. Variable speed switch (KFBES500) or On/Off switch

(KFBES410)

2. Lock-on button

3. Saw blade locking lever

ENGLISH

(Original instructions)

4. Shoe plate

5. Dust extraction outlet (KFBES500)

6. Pendulum stroke (KFBES500)

Assembly

Warning! Before attempting any of the following operations,

make sure that the tool is switched off and unplugged and that

the saw blade has stopped. Used saw blades may be hot.

Fitting the saw blade (g. A - KFBES500)

u Hold the saw blade (7) as shown, with the teeth facing

forward.

u Push the locking lever (3) away from the shoe plate (4).

u Insert the shank of the saw blade into the blade holder (8)

as far as it will go.

u Adjust the saw blade support roller (17) as described

above.

u Release the locking lever (3).

Fitting the saw blade (g. A - KFBES410)

u Before tting or removing the saw blade (7) the saw blade

support roller (17) must be adjusted to the rear position so

that it does not contact the blade.

u Loosen (do not remove) the two screws (18).

u Hold the saw blade (7) with the teeth facing forward.

u Insert the shank of the saw blade (7) into the blade holder

(8) as far as it will go.

u Slightly tighten the two screws (18) alternately to position

the blade, then fully tighten the two screws (18).

u Adjust the saw blade support roller (17) as described

above.

u To remove the saw blade (7), turn both screws (18) one

turn counterclockwise.

Connecting a vacuum cleaner to the tool (g. B -

KFBES500)

u Slide the vacuum nozzle (9) into the dust extration

outlet (5).

Use

Adjusting the shoe plate for bevel cuts (g. C)

Warning! Never use the tool when the saw shoe plate is loose

or removed.

The shoe plate (4) can be set to a left or right bevel angle

of 45°.

u Loosen the screws (10). Some models have one screw.

u Pull the shoe (4) forward, rotate the shoe to the left or right

and push it back into the 45° location. (KFBES500).

u Push the shoe (4) back, rotate to the right and pull it back

into the 45° location. (KFBES410 only).

u Tighten the screw.

To reset the shoe plate (4) for 90° cuts:

u Loosen the screw (10).

u Pull the shoe (4) forward, rotate to the centre and push it

back into the 0° location.

u Tighten the screw.

Variable speed control (KFBES500)

u Use a high speed for wood, medium speed for aluminium

and PVC and low speed for metals other than aluminium.

Switching on and off

u To switch the tool on, press the variable speed switch

(KFBES500) or the On/Off switch (KBES410) (1). On

KFBES500 units the speed depends on how far you

depress the switch.

u For continuous operation, press the lock-on button (2) and

press the variable speed switch. This option is available

only at full speed.

u To switch the tool off, release the variable speed switch. To

switch the tool off, when in continuous operation, press the

variable speed switch once more and release it.

How to Use the Sightline

Feature (g. D)

u Use a pencil to mark the cutting line.

u Position the jig saw over the line (11).

Viewing from directly above the jig saw, the line of cut can be

followed easily.

Cutting mode (KFBES500 only)

Pendulum stroke or action provides a more aggressive blade

motion and is designed for cutting soft materials such as wood

or plastic. It provides a faster cut, but with a less smooth cut

across the material. Your jig saw has a Pendulum Stroke dial.

Use of this dial is explained in the next section.

Note: Never use pendulum action to cut metal.

Pendulum Stroke dial (g. E - KFBES500 only)

The KS701PE has these four cutting modes with increasing

amounts of pendulum action:

u Position 0: metal and aluminium and sheet metal (no

pendulum action).

u Position 1: for laminates, hard wood, work tops.

u Position 2: for plywood and PVC/Plastics.

u Position 3: for soft wood and fast cutting.

To adjust the pendulum action:

u Rotate the Pendulum Stroke dial (6) to the required

position.

Sawing

Hold the tool rmly with both hands while cutting.

The shoe plate (4) should be held rmly against the material

being cut.

ENGLISH

(Original instructions)

This will help prevent the saw from jumping, reduce vibration

and minimise blade breakage.

u Let the blade run freely for a few seconds before starting

the cut.

u Apply only a gentle pressure to the tool while performing

the cut.

Hints for optimum use

Sawing laminates

When cutting laminates, splintering may occur which can

damage the presentation surface. The most common saw

blades cut on the upward stroke, therefore if the shoe plate is

sitting on the presentation surface either use a saw blade that

cuts on the downward stroke or:

u Use a ne-tooth saw blade.

u Saw from the back surface of the workpiece.

u To minimise splintering, clamp a piece of scrap wood or

hardboard to both sides of the workpiece and saw through

this sandwich.

Sawing metal

Warning! Do not use a vacuum when cutting metal. Metal

lings will be hot and may cause re.

Be aware that sawing metal takes much more time than

sawing wood.

u Use a saw blade suitable for sawing metal.

u When cutting thin sheet metal, clamp a piece of scrap

wood to the back surface of the workpiece and cut through

this sandwich.

u Spread a lm of oil along the intended line of cut.

Rip Fence (KFBES500)

Ripping and circle cutting without a pencil line are easily done

with a rip fence and circle guide (available as an optional extra

- part number X43005-XJ).

Attaching Rip Fence (gs. F & G)

u Insert rip fence (14) into the shoe plate slots with the cross

bar facing down as shown in gure F.

u Place screw (15) into hole in bottom of shoe plate.

u Align clamp bar (16) over screw with lipped edge facing

down and pointing towards the rear of the saw.

u Using a phillips screwdriver, run the screw into the

threaded hole in the bar clamp as shown in gure G.

u Adjust to width of cut and tighten screw.

Circle Cutting (g. H - KFBES500)

u Insert rip fence into slot on the right side of shoe plate with

cross bar facing up.

u Adjust rip fence so that distance from blade to hole in

cross bar is the desired radius and tighten screw.

u Place saw so that centre of hole in cross bar is over

centre of circle to be cut (make plunge cut, drill hole for

blade or cut inward from edge of material to get blade into

position).

u When saw is properly positioned, drive a small nail

through hole in cross bar into exact centre of circle to be

cut.

u Using rip fence as a pivot arm, begin cutting circle.

Plunge Cutting (g. I)

A plunge cut is an easy method of making an inside cut. The

saw can be inserted directly into a panel or board without

rst drilling a lead or pilot hole. In plunge cutting, measure

the surface to be cut and mark clearly with a pencil. Next tip

the saw forward until the front end of the shoe sits rmly on

the work surface and the blade clears the work through its

full stroke. Switch the tool on and allow it to attain maximum

speed. Grip the saw rmly and lower the back edge of tool

slowly until the blade reaches its complete depth. Hold the

shoe at against the wood and begin cutting. Do not remove

blade from cut while it is still moving. Blade must come to a

complete stop.

Maintenance

Your BLACK+DECKER tool has been designed to operate

over a long period of time with a minimum of maintenance.

Continuous satisfactory operation depends upon proper tool

care and regular cleaning.

u Regularly clean the ventilation slots in your tool using a

soft brush or dry cloth.

u Regularly clean the motor housing using a damp cloth. Do

not use any abrasive or solvent-based cleaner. Never let

any liquid get inside the tool and never immerse any part

of the tool into liquid.

Mains plug replacement (U.K. & Ireland only)

If a new mains plug needs to be tted:

u Safely dispose of the old plug.

u Connect the brown lead to the live terminal in the new

plug.

u Connect the blue lead to the neutral terminal.

Warning! No connection is to be made to the earth terminal.

Follow the tting instructions supplied with good quality plugs.

Recommended fuse: 5 A.

Protecting the environment

Separate collection. Products and batteries

marked with this symbol must not be disposed of

with normal household waste.

Products and batteries contain materials that can be

recovered or recycled reducing the demand for raw materials.

ENGLISH

(Original instructions)

Please recycle electrical products and batteries according to

local provisions. Further information is available at

www.2helpU.com

Technical data

KFBES410

(Type 1)

KFBES500

(Type 1)

Rated input power W

410 500

Input voltage

230 230

No-load speed

min

-1

3,000 0-3,000

Max depth of cut

Wood mm

65 70

Steel mm

5 5

Aluminium mm

10 15

Weight kg 1.3 1.7

KFBES410 Level of sound pressure according to EN 60745:

(sound pressure) 85 dB(A), Uncertainty (K) 3 dB(A)

(sound power) 96 dB(A), Uncertainty (K) 3 dB(A)

Vibration total values (triax vector sum) according to EN 60745:

Cutting boards (a

h, B

) 15.7 m/s

, uncertainty (K) 1.5 m/s

Cutting sheet metal (a

h, M

) 16.2 m/s

, uncertainty (K) 1.5 m/s

KFBES500 Level of sound pressure according to EN 60745:

(sound pressure) 89 dB(A), Uncertainty (K) 3 dB(A)

(sound power) 100 dB(A), Uncertainty (K) 3 dB(A)

Vibration total values (triax vector sum) according to EN 60745:

Cutting boards (a

h, B

) 12.5 m/s

, uncertainty (K) 1.5 m/s

Cutting sheet metal (a

h, M

) 9.9 m/s

, uncertainty (K) 1.5 m/s

EC declaration of conformity

MACHINERY DIRECTIVE

KFBES410, KFBES500 - Jig Saw

Black & Decker declares that these products described under

"technical data" are in compliance with:

2006/42/EC, EN60745-1:2009+A11:2010,

EN 60745-2-11:2010

These products also comply with Directive 2014/30/EU (from

20/04/2016) and 2011/65/EU. For more information, please

contact Black & Decker at the following address or refer to the

back of the manual.

The undersigned is responsible for compilation of the technical

le and makes this declaration on behalf of Black & Decker.

R. Laverick

Engineering Manager

Black & Decker Europe, 210 Bath Road, Slough,

Berkshire, SL1 3YD

United Kingdom

01/06/2018

Guarantee

Black & Decker is condent of the quality of its products and

offers consumers a 24 month guarantee from the date

of purchase. This guarantee is in addition to and in no way

prejudices your statutory rights. The guarantee is valid within

the territories of the Member States of the European Union

and the European Free Trade Area.

To claim on the guarantee, the claim must be in accordance

with Black & Decker Terms and Conditions and you will need

to submit proof of purchase to the seller or an authorised

repair agent. Terms and conditions of the Black & Decker 2

year guarantee and the location of your nearest authorised

repair agent can be obtained on the Internet at www.2helpU.

com, or by contacting your local Black & Decker ofce at the

address indicated in this manual.

Please visit our website www.blackanddecker.co.uk to register

your new Black & Decker product and receive updates on new

products and special offers.

ENGLISH

(Original instructions)

N602892 REV-0 06/2018

Australia Black & Decker (Australia) Pty. Ltd. Tel. 03-8720 5100

20 Fletcher Road, Mooroolbark, Fax 03-9727 5940

Victoria, 3138

New Zealand Black & Decker Tel. +64 9 259 1133

5 Te Apunga Place Fax +64 9 259 1122

Mt Wellington

Aukland 1060

United Kingdom & Black & Decker Tel. 01753 511234

Republic Of Ireland 210 Bath Road Fax 01753 512365

www.blackanddecker.co.uk Slough, Berkshire SL1 3YD

[email protected]

Black & Decker KFBES500 User manual

Brand: Black & Decker

Model: KFBES500

Category: Power tools

Type: User manual

This manual is also suitable for

Download PDF

report

Black & Decker KFBES500 User manual

This manual is also suitable for

Black & Decker KFBES500 User manual

Related papers

Other documents