Page is loading ...
Assembly Instructions - IMPORTANT! Keep for future reference
459/1467
Dimensions
Width - 72cm
Depth - 62cm
Height - 52.5cm
Important – Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400 800
BABY BY CHAD VALLEY RAINBOW WALKER
WARNING
IMPORTANT! – KEEP FOR FUTURE REFERENCE
Safety and Care Advice
MAINTENANCE
Read the instructions carefully before use and keep them for future reference. The child may be
hurt if you do not follow these instructions.
WARNING---Never leave the child unattended.
WARNING
---The child will be able to reach further and move rapidly when in the baby walking
Read the instructions carefully before use and keep them for future reference. The child
may be hurt if you do not follow these instructions.
1) Prevent access to stairs, steps and uneven surfaces;
2) Guard all fires, heating and cooking appliances;
3) Remove hot liquids, electrical flexes and other potential hazards from reach;
4) Prevent collisions with glass in doors, windows and furniture;
5) Do not use the baby walking frame if any components are broken or missing;
6) This baby walking frame should be used only for short periods of time(e.g.20min);
7) This baby walking frame is intended to be used by children who can sit unaided,
approximately from 6 months. It is not intended for children weighing more than 12kg;
8) Do not use replacement parts other than those approved by the manufacturer or distributor;
9) Follow instructions for routine maintenance and cleaning or washing.
Please check and maintain your walker regularly to prevent injury.
Inspect the parts regularly if some parts are broken.
Wash the plastic parts with warm soapy water.
1.Parts List
Please check you have all the parts listed below
If you have damaged or missing components,
call the
Customer Helpline:
03456 400 800
Phillips Screwdriver
T
Tools requirednot included
Toy
Frame
Seat
Tray
Bottom Base
Stopper
Wheel
2.
Assembly
Step1
Ste 2
Step3
p
4
directional
wheel
universal
wheel
1. Reverse the bottom base,
and insert the front levers
from the bottom slide hole.
2. Slide the front levers backward
3. Insert the rear levers into the
“8” shaped hole on the rear
bottom base.
4. Press the rear levers down.
Pull the upper tray to the
right position, make sure
the adjusting mechanism
is locked. Never put your
hands between the bottom
base and the upper tray to
avoid clamping
Insert the directional wheels
and universal wheels into
their corresponding holes.
rear lever
front lever
4
3
2
1
3
Step4
S
Step6
tep5
6
Locate the seat back. Insert
the seat back into the slots
on the back rim of the table
surface.
Locate the fabric seat. Insert
the fabric seat into the opening
as shown. Locate the eight
plastic tabs attached to the
perimeter of the seat. Insert
each of the eight plastic tabs
through the slots located around
the perimeter of the seat
assembly through the slot and
fasten into place.
Locate the bead chaser. Lower
each end of the toy into the
sockets at the front of the tray,
aligning the side of the socket.
Push down until the toy clicks
into place
Step7
Click
Locate the other toys. Align
the key at the base of each
toys with the notch in the side
of the socket. Puch each toy
down until it clicks into place.
3. User guide
1.
2.
adjusting button
adjusting
mechanism
adjusting button
adjusting
mechanism
To unfold the walker, please
pull the tray upward.
WARNING: Make sure the
adjusting mechanism is locked.
To fold the walker, turn the
adjusting button upword to
release the lock, then push the
tray downward to the folding
position and release the button
Your walker has 3 height
positions. To adjust the tray to
the desired height, simply pull
the tray up.
WARNING: Ensure locking
device is engaged.
To lower the tray, turn the
adjusting button to 90 degree
and press the lock, then adjust
the tray to desired position
Argos
Avebury, 489-499 Avebury Boulevard, Milton Keynes, MK9 2NW
www.argos.co.uk
Customer Helpline: 03456 400 800
/
