Parkside 113362 Operation and Safety Notes

IAN 113362

MODELLING & ENGRAVING SET PMGS 12 C3

MODELLBAU- UND GRAVIERSET

Bedienungs- und Sicherheitshinweise

Originalbetriebsanleitung

MODELLING & ENGRAVING SET

Operation and Safety Notes

Translation of the original instructions

MINI OUTIL ÉLECTRIQUE MULTIFONCTION

POUR MODÉLISME ET GRAVURE

Instructions d‘utilisation et consignes de sécurité

Traduction des instructions d‘origine

MODELLBYGGE- OCH GRAVERINGSSET

Bruksanvisning och säkerhetsanvisningar

Översättning av bruksanvisning i original

PIENOISMALLIEN RAKENNUS-

JA KAIVERRUSSARJA

Käyttö- ja turvaohjeet

Alkuperäisen käyttöohjeen käännös

MODELBOUW- EN GRAVEERSET

Bedienings- en veiligheidsinstructies

Vertaling van de originele gebruiksaanwijzing

GB / IE Operation and Safety Notes Page 5

FI Käyttö- ja turvaohjeet Sivu 19

SE Bruksanvisning och säkerhetsanvisningar Sidan 33

FR / BE Instructions d‘utilisation et consignes de sécurité Page 47

NL / BE Bedienings- en veiligheidsinstructies Pagina 63

DE / AT / CH Bedienungs- und Sicherheitshinweise Seite 77

Before reading, unfold the page containing the illustrations and familiarise yourself with all functions of the

device.

Käännä ennen lukemista kuvallinen sivu esiin ja tutustu seuraavaksi laitteen kaikkiin toimintoihin.

Vik ut bildsidan och ha den till hands när du läser igenom anvisningarna och gör dig bekant med

apparatens / maskinens funktioner.

Avant de lire le mode d‘emploi, ouvrez la page contenant les illustrations et familiarisez-vous ensuite avec

toutes les fonctions de l‘appareil.

Vouw vóór het lezen de pagina met de afbeeldingen open en maak u vertrouwd met alle functies van het

apparaat.

Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und machen Sie sich anschließend mit allen

Funktionen des Gerätes vertraut.

A

11

8 9

C

B

16

14

15

18

22

20

21

13

12

23

10

D

F

E

G

17

19

1

2

3

5 4

7

4

24

6

5 GB/IE

Table of contents

Introduction

Proper use ............................................................................................................................................Page 6

Features and equipment .....................................................................................................................Page 6

Included items .....................................................................................................................................Page 6

Technical information .......................................................................................................................... Page 6

General safety advice for electrical power tools

1. Workplace safety ...........................................................................................................................Page 7

2. Electrical safety ............................................................................................................................... Page 7

3. Personal safety ................................................................................................................................Page 8

4. Careful handling and use of electrical power tools .....................................................................Page 8

5. Use and handling of the cordless electrical power tool ..............................................................Page 9

6. Service .............................................................................................................................................Page 9

Safety instructions for all operations .................................................................................................. Page 9

Further safety instructions for all operations ......................................................................................Page 10

Additional safety instructions for grinding and cutting-off operations .............................................Page 11

Additional safety instructions for wire brushing operations ..............................................................Page 12

Safety notices for power drills ............................................................................................................ Page 12

Safety instructions for LED lights ......................................................................................................... Page 12

Device-specific safety instructions for small drill PMGS 12 C3 and mains

adapter-PMGS 12 C3-1 .....................................................................................................................Page 12

Operation

Changing the battery .......................................................................................................................... Page 13

Inserting or replacing a tool / collet ...................................................................................................Page 13

Switching on and off / Setting the speed range ................................................................................Page 14

Using the grip collar with LED light ....................................................................................................Page 14

Advice on working with materials / Tools / Speed ranges ...............................................................Page 14

Tips and tricks ...................................................................................................................................... Page 15

Maintenance and cleaning ............................................................................................... Page 15

Service ...............................................................................................................................................Page 16

Warranty .........................................................................................................................................Page 16

Disposal ............................................................................................................................................Page 16

Translation of the original declaration of conformity /

Manufacturer ............................................................................................................................... Page 17

6 GB/IE

Introduction

Modelling & engraving set

PMGS 12 C3

Q

Introduction

We congratulate you on the purchase of your new

device. You have chosen a high quality product. The

instructions for use are part of the product. They

contain important information concerning safety,

use and disposal. Before using the product, please

familiarise yourself with all of the safety information

and instructions for use. Only use the unit as de

scribed

and for the speciﬁed applications. If you pass the

product on to anyone else, please ensure that you

also pass on all the documentation with it.

Q

Proper use

The small drill is to be used for drilling, milling, en-

graving, polishing, cleaning up, grinding, separating

and sawing of wood, metal, plastic, ceramic or stone

in dry rooms. Any other use or modiﬁcation to the

drill / grinder shall be considered as improper use

and could give rise to considerable dangers. The

manufacturer will not accept liability for loss or

damage arising from improper use. Not intended

for commercial use.

Q

Features and equipment

Modelling & engraving set:

1

ON / OFF switch / speed control

2

Plug for power supply

3

Metal bracket

4

Grip collar

5

Clamping nut

6

Grip collar with LED light

7

Spindle lock

Mains adapter (see Fig. A):

8

Plug-in device for plug

2

9

Tray

10

Mains adapter

11

Power cable (with mains plug)

Accessories (see Fig. B):

12

6 HSS drills

13

2 Mandrels for mounting tools

14

3 Polishing wheels

15

4 Grinding wheels

16

1 Metal brush

17

16 Cutting wheels

18

5 Collets

19

2 Plastic brushes

20

3 Milling bits

21

2 Engraving bits

22

5 Grinding bits

23

1 Combination tool

24

LED light ON / OFF switch

Q

Included items

1 Modelling & engraving set

1 Mains adapter

1 Plastic case

1 Accessory kit (50-piece)

1 Handle ring incl. batteries

1 Operating instructions

Q

Technical information

Modelling & engraving set PMGS 12 C3:

Nominal voltage: 12 V

Nominal input

power: 22 W

Idle-running speed: n 5000–20000 min

-1

Drill bit

diameter

: max. ø 3.2 mm

Disc: max. ø 25 mm

Certiﬁed acc. to:

EN60745-1:2009/A11:2010,

EN60745-2-1:2010,

EN60745-2-23:2013

Noise and vibration data:

Measured values for noise are determined in accor-

dance with EN 60745. The A-weighted noise level

of the electrical power tool are typically:

Sound pressure level: 57.3 dB(A)

Sound power level: 68.3 dB(A)

Uncertainty K: 3 dB

Introduction / General safety advice for electrical power tools

7 GB/IE

Introduction / General safety advice for electrical power tools

Evaluated acceleration, typical:

Hand / arm vibration: 0.817 m / s

2

Uncertainty K = 1.5 m / s

2

Note: The vibration level speciﬁed in these instruc-

tions was measured in accordance with an EN 60745

standardised measurement process and can be used

to compare equipment. The vibration emission value

speciﬁed can also serve as a preliminary assessment

of the exposure.

The vibration level will change according to the

application of the electrical tool and in some cases

may exceed the value speciﬁed in these instructions.

Regularly using the electric tool in such a way may

make it easy to underestimate the vibration.

Try to keep the vibration loads

as low as possible. Measures to reduce the vibration

load are, e.g. wearing gloves and limiting the work-

ing time. Wherein all states of operation must be in-

cluded (e.g. times when the power tool is switched

oﬀ and times where the power tool is switched on but

running without load).

Mains adapter PMGS 12 C3-1:

INPUT:

Rated voltage: 230 V∼ 50 Hz

OUTPUT:

Nominal voltage: 12 V

Nominal current: 1 A

Protection class: II /

Protection type: IP20

Certiﬁed acc. to: EN 61558-1:2006 / A1:2009,

EN 61558-2-6:2009

General safety advice for

electrical power tools

Read

all safety warnings

and all instructions.

Failure to follow the warnings and instructions may

result in electric shock, ﬁre and / or serious injury.

Keep all the safety advice and instructions

in a safe place for future reference!

The term “electrical tool” used in the safety advice

refers to electrical tools powered by mains electricity

(by means of a mains lead) and electrical tools pow-

ered by rechargeable batteries (without a mains lead).

1. Workplace safety

a) K

eep your working area clean and wel

l

lit. Untidy or poorly lit working areas can lead

to accidents.

b) Do not work with the device in poten-

tially explosive environments in which

there are inflammable liquids, gases o

r

dusts. Electrical power tools create sparks,

which can ignite dusts or fumes.

c) Keep children and other people away

while you are operating the electrical

tool. Distractions can cause you to lose con-

trol of the device.

2. Electrical safety

a) The mains plug on the power tool (or

on the power supply) must ﬁt the

mains

socket. Never modify the plug in any

way. Never use adapter plugs with

earthed power tools. Unmodiﬁed plugs

and the correct sockets reduce the risk of elec-

tric shock.

b) Avoid touching earthed surfaces such

as pipes, radiators, ovens and refrig-

erators with any part of your body.

There is an increased risk of electric shock if

your body is earthed.

c) Keep the device away from rain or

moisture. Water entering an electrical device

increases the risk of electric shock.

d) Do not use the mains lead for any pur-

pose for which it was not intended, e.

g.

to carry the device, to hang up the de-

vice or to pull the mains plug out of

the mains socket. Keep the mains lead

away from heat, oil, sharp edges or

moving parts of the device. Damaged or

tangled mains leads increase the risk of elec-

tric shock.

8 GB/IE

General safety advice for electrical power tools

e) When working outdoors with an elec-

trical power tool always use extension

cables that are also approved for use

outdoors. The use of an extension cable suit-

able for outdoor use reduces the risk of elec-

tric shock.

f) Use a residual current device (RCD) for

protection if operating the electrical

power tool in a moist environment is

unavoidable. The use of an RCD reduces

the risk of electric shock.

3. Personal safety

a) Remain alert at all times, watch what

you are doing and always proceed

with caution. Do not use the device if

you are tired or under the influence of

drugs, alcohol or medication. One mo

ment

of carelessness when using the device can lead

to serious injury.

b) Wear personal protective equipment

and always wear safety glasses. The

wearing of personal protective equipment such

as dust masks, non-slip safety shoes, safety hel-

mets or ear protectors, appropriate to the type

of electrical power tool used and work under-

taken, reduces the risk of injury.

c) Avoid accidental starting. Verify the po-

wer tool is switched oﬀ before connec-

ting it to the mains and / or connecting

the battery, picking it up, or carrying it.

Accidents can happen if you carry the device

with your ﬁnger on the ON / OFF switch or with

the device switched on.

d) Remove any setting tools or spanners

before you switch the device on. A tool

or spanner left attached to a rotating part of a

device can lead to injury.

e) Avoid placing your body in an unnat-

ural position. Keep proper footing and

balance at all times. By doing this you will

be in a better position to control the device in

unforeseen circumstances.

f) Wear suitable clothing. Do not wear

loose clothing or jewellery. Keep your

hair, clothing and gloves clear of mov-

ing parts. Loose clothing, jewellery or long

hair can become trapped in moving parts.

g) If vacuum dust extraction and collection

devices are fitted do not forget to

check

that they are properly connected and

correctly used. The use of these devices

reduces the hazard presented by dust.

4. Careful handling and use

of electrical power tools

a) Do not overload the device. Always

use an electrical power tool that is

intended for the task you are under-

taking. By using the right electrical power

tool for the job you will work more safely and

achieve a better result.

b) Do not use an electrical power tool if

its switch is defective. An electrical power

tool that can no longer be switched on and oﬀ

is dangerous and must be repaired.

c) Pull the mains plug out of the socket

and / or remove the rechargeable bat-

tery before you make any adjustments

to the device, change accessories or

when the device is put away. This pre-

caution is intended to prevent the device from

unintentionally starting.

d) When not in use always ensure that

electrical power tools are kept out of

reach of children. Do not let anyone

use

the device if he or she is not familiar

with it or has not read the instructions

and advice. Electrical power tools are dan-

gerous when they are used by inexperienced

people.

e) Look after the device carefully. Check

that moving parts are working prop-

erly and move freely. Check for any

parts that are broken or damaged

enough to detrimentally affect the

functioning of the device. Have dam-

aged parts repaired before you use

the device. Many accidents have their origins

in poorly maintained electrical power tools.

f) Keep cutting tools clean and sharp.

Carefully maintained cutting tools with sharp

General safety advice for electrical power tools

9 GB/IE

General safety advice for electrical power tools

cutting edges are less likely to jam and are

easier to control.

g) Use the electrical power tool, accesso-

ries, inserted tools etc. in accordance

with these instructions and advice, and

the stipulations drawn up for this par-

ticular type of device. In doing this, take

into account the working conditions

and the task in hand. The use of electrical

power tools for purposes other than those in-

tended can lead to dangerous situations.

5. Use and handling of the

cordless electrical power tool

a) Charge a rechargeable battery unit

using only the charger recommended

by the manufacturer. Chargers are often

designed for a particular type of rechargeable

battery unit. There is the danger of ﬁre if other

types of rechargeable battery units are used.

b) Only the rechargeable battery units

supplied are to be used with an elec-

trical power tool. The use of other recharge-

able battery units may lead to the danger of

injury or ﬁre.

c) When they are not being used, store

rechargeable battery units away from

paperclips, coins, keys. nails, screws

or other small metal objects that could

cause the contacts to be bridged. Short-

circuiting the contacts of a rechargeable battery

unit may result in heat damage or ﬁre.

d) Fluids may leak out of rechargeable

battery units if they are misused. If this

happens, avoid contact with the ﬂuid.

If contact occurs, ﬂush the aﬀected area

with water. Seek additional medical

help if any of the ﬂuid gets into your

eyes. Escaping battery ﬂuid may cause skin

irritation or burns.

CAUTION! DANGER OF EXPLOSION!

The batteries must never be recharged!

6. Service

a) Have your device repaired at the ser-

vice centre or by qualified specialist

personnel using original manufacturer

parts only. This will ensure that your device

remains safe to use.

Safety instructions for all

operations

Safety warnings common for grinding,

sanding, wire brushing, polishing, carving

or abrasive cutting-off operations:

a) This power tool is intended to function

as a grinder, sander, wire brush, pol-

isher, carving or cut-off tool. Read all

safety warnings, instructions, illustra-

tions and specifications provided with

this power tool. Failure to follow all instruc-

tions listed below may result in electric shock,

fire and / or serious injury.

b) Do not use accessories which are not

specifically designed and recommend-

ed by the tool manufacturer. Just because

the accessory can be attached to your power

tool, it does not assure safe operation.

c) The rated speed of the grinding acces-

sories must be at least equal to the

max-

imum speed marked on the power

tool.

Grinding accessories running faster than their

rated speed can break and fly apart.

d) The outside diameter and the thickness

of your accessory must be within the

capacity rating of your power tool. In-

correctly sized accessories cannot be ade

quately

controlled.

e) The arbour size of wheels, sanding

drums or any other accessory must

properly fit the spindle or collet of the

power tool. Accessories that do not match

the mounting hardware of the power tool will

run out of balance, vibrate excessively and may

cause loss of control.

f) Mandrel mounted wheels, sanding

drums, cutters or other accessories

must be fully inserted into the collet

10 GB/IE

General safety advice for electrical power tools

or chuck. If the mandrel is insufficiently held

and / or the overhang of the wheel is too long,

the mounted wheel may become loose and be

ejected at high velocity.

g) Do not use a damaged accessory. Be-

fore each use inspect the accessory

such

as abrasive wheels for chips and cra

cks,

sanding drum for cracks, tear or excess

wear, wire brush for loose or cracked

wires. If power tool or accessory is

dropped, inspect for damage or install

an undamaged accessory. After in

spect-

ing and installing an accessory, position

yourself and bystanders away from

the plane of the rotating accessory

and

run the power tool at maximum no-

load

speed for one minute. Damaged accesso-

ries will normally break apart during this test time.

h) Wear personal protective equipment.

Depending on application, use face

shield, safety goggles or safety glass-

es. As appropriate, wear dust mask,

hearing protectors, gloves and work-

shop apron capable of stopping small

abrasive or workpiece fragments. The

eye protection must be capable of stopping

flying debris generated by various operations.

The dust mask or respirator must be capable of

filtrating particles generated by your operation.

Prolonged exposure to high intensity noise may

cause hearing loss.

i) Keep bystanders a safe distance away

from work area. Anyone entering the

work area must wear personal protec-

tive equipment. Fragments of workpiece or

of a broken accessory may fly away and cause

injury beyond immediate area of operation.

j) Hold power tool by insulated gripping

surfaces only, when performing an

op-

eration where the cutting accessory may

contact hidden wiring or its own cord.

Cutting accessory contacting a «live» wire may

make exposed metal parts of the power tool

«live» and could give the operator an electric shock.

k) Always hold the tool firmly in your

hand(s) during the start-up. The reaction

torque of the motor, as it accelerates to full

speed,

can cause the tool to twist.

l) U

se clamps to support workpiece wh

en-

ever practical. Never hold a small

work-

piece in one hand and the tool in the

other hand while in use. Clamping a small

workpiece allows you to use your hand(s) to

control the tool. Round material such as dowel

rods, pipes or tubing have a tendency to roll

while being cut, and may cause the bit to bind

or jump toward you.

m) Position the cord clear of the spinning

accessory. If you lose control, the cord may

be cut or snagged and your hand or arm may

be pulled into the spinning accessory.

n) Never lay the power tool down until

the accessory has come to a complete

stop. The spinning accessory may grab the

surface and pull the power tool out of your control.

o) After changing the bits or making any

adjustments, make sure the collet nut,

chuck or any other adjustment devices

are securely tightened. Loose adjustment

devices can unexpectedly shift, causing loss of

control, loose rotating components will be vio-

lently thrown.

p) Do not run the power tool while car-

rying it at your side. Accidental contact

with the spinning accessory could snag your

clothing, pulling the accessory into your body.

q) Regularly clean the power tool’s air

vents. The motor’s fan will draw the dust inside

the housing and excessive accumulation of pow-

dered metal may cause electrical hazards.

r) Do not operate the power tool near

flammable materials. Sparks could ignite

these materials.

s) Do not use accessories that require

liquid coolants. Using water or other liquid

coolants may result in electrocution or shock.

Further safety instructions

for all operations

Kickback and related warnings

Kickback is a sudden reaction to a pinched or sn

agged

rotating wheel, sanding band, brush or any other

accessory. Pinching or snagging causes rapid stalling

of the rotating accessory which in turn causes the

General safety advice for electrical power tools

11 GB/IE

General safety advice for electrical power tools

uncontrolled power tool to be forced in the direction

opposite of the accessory’s rotation.

For example, if an abrasive wheel is snagged or

pinched by the workpiece, the edge of the wheel

that is entering into the pinch point can dig into the

surface of the material causing the wheel to climb

out or kick out. The wheel may either jump toward

or away from the operator, depending on direction

of the wheel’s movement at the point of pinching.

Abrasive wheels may also break under these con-

ditions.

Kickback is the result of power tool misuse and / or

incorrect operating procedures or conditions and

can be avoided by taking proper precautions as

given below.

a) Maintain a firm grip on the power tool

and position your body and arm to al-

low you to resist kickback forces. The

operator can control kickback forces, if proper

precautions are taken.

b) U

se special care when working corne

rs,

sharp edges etc. Avoid bouncing and

snagging the accessory. Corners, sharp

edges or bouncing have a tendency to snag the

rotating accessory and cause loss of control or

kickback.

c)

Do not attach a toothed saw blade. S

uch

blades create frequent kickback and loss of

control.

d) Always feed the bit into the material

in the same direction as the cutting

edge is exiting from the material

(which

is the same direction as the chips are

thrown). Feeding the tool in the wrong direc-

tion causes the cutting edge of the bit to climb

out of the work and pull the tool in the direction

of this feed.

e) When using rotary files, cut-off wheels,

high-speed cutters or tungsten carbide

cutters, always have the work securely

clamped. These wheels will grab if they be-

come slightly canted in the groove, and can

kickback. When a cut-off wheel grabs, the

wheel itself usually breaks. When a rotary file,

high-speed cutter or tungsten carbide cutter

grabs, it may jump from the groove and you

could lose control of the tool.

Additional safety instructions

for grinding and cutting-oﬀ

operations

Safety warnings specific for grinding and

abrasive cutting-off operations:

a) Use only wheel types that are recom-

mended for your power tool and only

for recommended applications.

For example: do not grind with the

side of a cut-off wheel. Abrasive cut-off

wheels are intended for peripheral grinding,

side forces applied to these wheels may cause

them to shatter.

b) For threaded abrasive cones and plugs

use only undamaged wheel mandrels

with an unrelieved shoulder flange that

are of correct size and length. Proper

man-

drels will reduce the possibility of breakage.

c) Do not “jam” a cut-off wheel or apply

excessive pressure. Do not attempt to

make an excessive depth of cut. Over-

stressing the wheel increases the loading and

susceptibility to twisting or snagging of the wheel

in the cut and the possibility of kickback or w

heel

breakage.

d) Do not position your hand in line with

and behind the rotating wheel. When

the wheel, at the point of operation, is moving

away from your hand, the possible kickback m

ay

propel the spinning wheel and the power tool

directly at you.

e) When wheel is pinched, snagged or

when interrupting a cut for any reason,

switch off the power tool and hold the

power tool motionless until the wheel

comes to a complete stop. Never att

empt

to remove the cut-off wheel from the

cut while the wheel is in motion other-

wise kickback may occur. Investigate and

take corrective action to eliminate the cause of

wheel pinching or snagging.

12 GB/IE

General safety advice for electrical power tools

f) Do not restart the cutting operation in

the workpiece. Let the wheel reach full

speed and carefully re-enter the cut.

The wheel may bind, walk up or kickback if

the power tool is restarted in the workpiece.

g) Support panels or any oversized work-

piece to minimize the risk of wheel

pinching and kickback. Large workpieces

tend to sag under their own weight. Supports

must be placed under the workpiece near the

line of cut and near the edge of the workpiece

on both sides of the wheel.

h) Use extra caution when making a

“pocket cut” into existing walls or

other blind areas. The protruding wheel

may cut gas or water pipes, electrical wiring

or objects that can cause kickback.

Additional safety instructions

for wire brushing operations

Safety warnings specific for wire brushing

operations:

a) Be aware that wire bristles are thrown

by the brush even during ordinary op-

eration. Do not overstress the wires

by applying excessive load to the

brush.

The wire bristles can easily penetrate light cloth-

ing and / or skin.

b)

Allow brushes to run at operating spe

ed

for at least one minute before using

them. During this time no one is to

stand

in front or in line with the brush. Loose

bristles or wires will be discharged during the

run-in time.

c) D

irect the discharge of the spinning wir

e

brush away from you. Small particles and

tiny wire fragments may be discharged at high

velocity during the use of these brushes and

may become imbedded in your skin.

Safety notices for power drills

Losing control can result in injury.

Hold the tool by the insulated handles when

performing work where there is a potential risk

of the tool striking electric lines or its own power

cable. Contact with a live wire can also charge

metal parts of the device, resulting in electric shock.

Safety instructions for LED lights

ATTENTION! RISK OF EYE INJURY! Never

aim the light beam directly at people or animals,

and never look directly into the light beam of

LED lights.

Q

D

evice-speciﬁc safety instructi

ons

for small drill PMGS 12 C3 and

mains adapter-PMGS 12 C3-1

When you use the drill /

grinder wear the following

protective equipment: safety glasses

and protective gloves.

For indoor use only!

CAUTION! The tool continues to rotate

after it has been switched off! Avoid

contact with rapidly rotating drill / grinder com-

ponents.

Securely support the

workpiece. Use clamps or a vice to grip the

workpiece ﬁrmly. This is much safer than holding

it in your hand.

Never support your-

self by placing your hands near or in

front of the device or the workpiece

surface. A slip can result in injury.

Avoid contact with moving sanding or

grinding tools.

DANGER OF FIRE FROM FLYING

SPARKS!

Abrading metal creates ﬂying sparks. For this

reason, always make sure that nobody is placed

in any danger and that there are no inﬂamma

ble

materials near the working area.

DUST HAZARD! Any

harmful / noxious dusts generated from machin-

ing represent a risk to the health of the person

operating the device and to anyone near the

work area.

General safety advice for electrical power tools / Operation

13 GB/IE

General safety advice for electrical power tools / Operation

Wear a dust mask!

NOXIOUS FUMES!

Ensure that there is adequate ventilation when

machining surfaces containing plastic or cov-

ered with paint, varnish etc.

Do not soak the materials or the sur-

face you are about to work on with

liquids containing solvents.

Avoid abrading paints containing lead

or other substances hazardous to

health.

Do not machine materials containing

asbestos. Asbestos is a known carcinogen.

Do not machine moist materials or

damp surfaces.

NOTE! Do not allow the tool to come to a

standstill by overloading it!

Switch the device off

and allow it to come to a standstill be-

fore you put it down.

Always keep the de

vice

clean, dry and free of oil or grease.

This device is not intended to be used by per-

sons (including children) with impaired physi-

cal, sensory or mental capacity or lacking the

experience and / or knowledge. Always super-

vise children to ensure they do not play with

the tool.

If the external connection wire / cable(s)

for this transformer is / are damaged, it / they

must be replaced by the manufacturer or its cus-

tomer service, or a similarly qualiﬁed person to

avoid hazards.

Safety isolating transformer

fail-safe

Fusible cut-out

Q

Operation

Never use the device for a purpose

for which it was not intended or with

non-original parts / accessories. The use

of tools or accessories other than those recom-

mended in the operating instructions could lead

to you suﬀering an injury.

Changing the battery

ATTENTION!

Do not leave drained battery in the device, as

even leak-proof batteries can corrode, releasing

chemicals which could be harmful to your health

or ruin the device.

Do not leave batteries lying about carelessly.

Children or pets could swallow them. If acciden-

tally swallowed seek immediate medical attention

.

Remove the batteries from the device when it

will not be used for extended periods to prevent

leaks.

Touching leaked or damaged batteries may

cause chemical burns. Therefore wear suitable

protective gloves in this event.

Ensure batteries are not short-circuited. Never

throw batteries into ﬁre.

Do not recharge batteries. Explosion hazard!

Ensure the LED light is switched oﬀ. Remove the

three battery cover screws at the back of the

grip collar with LED

6

.

Remove the drained battery and replace with a

new battery (button cell LR41). Please note the

correct polarity when inserting the batteries.

Close the battery compartment by fastening the

three screws.

Q

Inserting or replacing

a tool / collet

Press the spindle lock

7

and keep it pressed.

Rotate the clamping nut

5

until the lock

engages.

Loosen the clamping nut

5

with the combina-

tion key

23

.

If a tool is already inserted, remove it.

First insert the tool you wish to use through the

clamping nut

5

before you insert it into the

collet

18

suitable for the tool shaft.

Press the spindle lock

7

and keep it pressed.

Insert the collet

18

into the threaded insert and

tighten the clamping nut

5

on the thread using

the combination key

23

.

14 GB/IE

Operation

Using the Insertion tool with mandrel

13

:

NOTE: Use the screwdriver end of the combi-

nation key

23

to release or tighten the screw of

the mandrels

13

.

Insert the mandrel

13

into the electrical tool as

described.

With the aid of the combination wrench

23

,

unscrew the screw from the mandrel

13

.

Place the insertion tool you wish to have onto

the screw between the two washers.

With the aid of the combination wrench

23

,

tighten the screw on the mandrel

13

.

Q

Switching on and oﬀ /

Setting the speed range

Switching on / Setting the speed range:

Connect the plug

2

to the power supply unit

10

by inserting it into the plug-in device

8

provided

for such purposes (see Fig. A).

Connect the device to the power supply by

inserting the mains plug into the socket.

Slide the ON / OFF switch

1

to a position

between “5000“ and “20000“.

Switching off:

Slide the ON / OFF switch

1

to the “OFF“

position.

Using the grip collar

with LED light

Hold the spindle lock

7

and unscrew the

clamping nut

5

from the thread, turning coun-

ter-clockwise.

Release the spindle lock

7

.

Then unscrew the grip collar

4

from the

thread, turning counter-clockwise.

Screw the grip collar with LED light

6

onto the

thread, turning clockwise.

Hold the spindle lock

7

and screw the clamp-

ing nut

5

onto the thread, turning clockwise.

Release the spindle lock

7

.

Set the ON / OFF switch of the LED light

24

to

position “I“ to switch it on.

Set the ON / OFF switch of the LED light

24

to

position “0“ to switch it oﬀ again.

Repeat the steps in reverse order to reattach the

grip collar

4

.

Q

Advice on working with

materials / Tools / Speed ranges

Use the highest speed when working on steel

or iron with the milling bits

20

.

Use a short trial on a test piece to determine the

optimum rotational speed range for working on

zinc, zinc alloy, aluminium, copper and lead.

Use the low speed range for working on plastics

and low-melting point materials.

Use high speeds on wood.

Use the medium speed range for cleaning,

polishing and buﬃng.

The following information shall be considered as

recommendatory only. Learn by practical experience

which tools and settings are the best for the materi-

als you work with.

Setting the appropriate speed:

Numeral on the

rotational speed

control

1

Material to be

worked on

5000

Plastics and low melting

point materials

9000

Stone, Ceramics

13000

Softwood, metal

17000

Hardwood

20000

Steel

Operation / Maintenance and cleaning

15 GB/IE

Operation / Maintenance and cleaning

Examples of appropriate tool selection Function:

Function Accessory Application Projection

(min–max) mm

Drilling

HSS drill

12

Drilling wood 18–25 when us-

ing the smallest

drill the projection

is 10 mm

Milling

Milling bits

20

Various tasks, e.g. hollowing out, goug-

ing, shaping, grooving or slotting

18–25

Engraving Engraving

bits

21

Making marks, craft projects

(see Fig. D)

18–25

Polishing, derusting

CAUTION!

Use only the lightest

contact pressure of

the tool on the

workpiece.

Metal brush

16

Derusting

9–15

Polishing wheel

14

Working on various metals and plastics,

in particular noble metals like gold or

silver (see Fig. E)

12–18

Cleaning

Plastic brush

19

E.g. cleaning complex plastic housings

or the area around a door lock

9–15

Grinding Grinding

wheels

15

Grinding work on stone, wood; ﬁne

work on hard materials such as ceramic

or alloyed steel (see Figs. F, G)

12–18

Grinding bits

22

10

Cutting and sawing

Cutting discs

17

Cutting metal,

plastic or wood

12–18

Be sure not to exceed the maximum diameter of

composite abrasive wheels and grinding cones

and cylinders with 55 mm thread insert, and

the 80 mm maximum diameter of sandpaper

grinding accessories.

Note: The max. permissible mandrel length is

33 mm.

Store accessories inside the original box or oth-

erwise protect the accessories from damage.

Store accessories dry and away from aggres-

sive media.

Tips and tricks

Applying excessive pressure can cause the in-

stalled tool to break and / or damage the work

piece. Optimal results can be achieved by ap-

plying the tool to the work piece at a steady

speed range and little pressure.

Hold the device with both hands whilst cutting.

Please note the data and information in the

chart to prevent the spindle end touching the

perforated plate of the grinding tool.

Q

Maintenance and cleaning

The device is maintenance-free.

Clean all the dirt oﬀ the drill / grinder. Use a

dry cloth for cleaning.

16 GB/IE

Service / Warranty / Disposal

Q

Service

Have your device

repaired at the service centre or by

qualified specialist personnel using

original manufacturer parts only. This

will ensure that your device remains safe to use.

If the plug or lead

needs to be replaced, always have

the replacement carried out by the

manufacturer or its service centre. This

will ensure that your device remains safe to use.

Note: Spare parts not listed (e.g. carbon brushes,

switches) can be ordered through our call centre.

Q

Warranty

The warranty for this appliance is for 3

years from the date of purchase. The ap-

pliance has been manufactured with care

and meticulously examined before deliv-

ery. Please retain your receipt as proof of

purchase. In the event of a warranty claim,

please make contact by telephone with our

Service Department. Only in this way can a

p

ost-free despatch for your goods be assured.

The warranty covers only claims for material and

maufacturing defects, but not for transport damage,

for wearing parts or for damage to fragile compo-

nents, e.g. buttons or batteries. This product is for pri-

vate use only and is not intended for commercial use.

The warranty is void in the case of abusive and im-

proper handling, use of force and internal tamper-

ing not carried out by our authorized service branch.

Your statutory rights are not restricted in any way

by this warranty.

The warranty period will not be extended by repairs

made unter warranty. This applies also to replaced

and repaired parts. Any damage and defects extant

on purchase must be reported immediately after

unpacking the appliance, at the latest, two days after

the purchase date. Repairs made after the expiration

of the warranty period are subject to payment.

GB

Service Great Britain

Tel.: 0871 5000 720

(0.10 GBP / Min.)

e-mail: k[email protected]

IAN 113362

IE

Service Ireland

Tel: 1890 930 034

(0.08 EUR / Min. (peak)

0.06 EUR / Min. (off peak))

e-mail: k[email protected]

IAN 113362

Q

Disposal

The packaging is wholly composed of

environmentally-friendly materials that can

be disposed of at a local recycling centre.

Do not dispose of electric tools

in the household waste!

In accordance with European Directive

2012 / 19 / EU

about waste electrical and electronic equipment

and its transposition into national legislation, worn

out electric tools must be collected separately and

taken for environmentally compatible recycling.

Please contact your municipal or city council to ask

about how to dispose of old electrical tools.

Batteries may not be disposed

of in household waste!

Every consumer is legally obligated to return batter-

ies to a municipal collection site or a retail store.

This duty is to ensure batteries are disposed of in

an environmentally friendly manner. Only return

drained batteries.

Translation of the original declaration of conformity / Manufacturer

17 GB/IE

Translation of the original declaration of conformity / Manufacturer

Translation of the original

declaration of conformity /

Manufacturer

We, KOMPERNASS HANDELS GMBH, the person

responsible for documents: Mr Semi Uguzlu, BURG-

STRASSE 21, 44867 BOCHUM, GERMANY, hereby

declare that this product complies with the following

standards, normative documents and EU directives:

Machinery Directive

(2006 / 42 / EC)

EU Low Voltage Directive

(2006 / 95 / EC)

Electromagnetic Compatibility

(2014 / 30 / EU)

RoHS Directive

(2011 / 65 / EU)

Applicable harmonized standards

EN 60745-1:2009/A11:2010

EN 60745-2-1:2010

EN 60745-2-23:2013

EN 55014-1:2006/A2:2011

EN 55014-2:1997/A2:2008

EN 61000-3-2:2014

EN 61000-3-3:2013

EN 61558-1:2006/A1:2009

EN 61558-2-6:2009

Type / Device description:

Modelling & engraving set PMGS 12 C3

Date of manufacture (DOM): 07–2015

Serial number: IAN 113362

Bochum, 31.07.2015

Semi Uguzlu

- Quality Manager -

We reserve the right to make technical modiﬁcations

in the course of further development.

18

Sisällysluettelo

19 FI

Yleistä

Määräystenmukainen käyttö ............................................................................................................... Sivu 20

Varusteet ............................................................................................................................................... Sivu 20

Toimituslaajuus ..................................................................................................................................... Sivu 20

Tekniset tiedot ....................................................................................................................................... Sivu 20

Sähkötyökaluja koskevat yleiset turvaohjeet

1. Työpaikkaturvallisuus....................................................................................................................... Sivu 21

2. Sähköturvallisuus ............................................................................................................................. Sivu 21

3. Henkilöiden turvallisuus ................................................................................................................... Sivu 22

4. Sähkötyökalujen huolellinen käsittely ja käyttö ............................................................................. Sivu 22

5. Akkutyökalun käyttö ja käsittely ..................................................................................................... Sivu 22

6. Huolto ............................................................................................................................................... Sivu 23

Kaikkia käyttötapoja koskevat turvallisuusohjeet ............................................................................... Sivu 23

Kaikkia käyttötapoja koskevat lisäturvallisuusohjeet ......................................................................... Sivu 24

Hiontaa ja katkaisuhiontaa koskevat lisäturvallisuusohjeet ............................................................... Sivu 25

Teräsharjan käyttöä koskevat lisäturvallisuusohjeet ........................................................................... Sivu 26

Porakoneita koskevat turvallisuusohjeet ............................................................................................. Sivu 26

LED-valaisimia koskevat turvallisuusohjeet .......................................................................................... Sivu 26

Pienoisporakoneen PMGS 12 C3 ja verkkolaitteen PMGS 12 C3-1 laitekohtaiset turvaohjeet ... Sivu 26

Käyttöönotto

Paristojen vaihto ................................................................................................................................... Sivu 27

Työkalun / kiinnitysholkin kiinnittäminen / vaihtaminen ...................................................................... Sivu 27

Päälle- ja poiskytkeminen / Pyörimisnopeusalueen asettaminen ....................................................... Sivu 28

LED-valolla varustetun kiinnitysrenkaan käyttö ................................................................................... Sivu 28

Ohje materiaalin työstöön / Työkalu / Pyörimisnopeusalue .............................................................. Sivu 28

Vihjeet ja vinkit ..................................................................................................................................... Sivu 29

Huolto ja puhdistus .................................................................................................................. Sivu 29

Huolto.................................................................................................................................................. Sivu 30

Takuu ................................................................................................................................................... Sivu 30

Hävittäminen ................................................................................................................................ Sivu 30

Käännös alkuperäisestä EY-

vaatimustenmukaisuusvakuutuksesta / Valmistajan ................................ Sivu 31

Sisällysluettelo

20 FI

Yleistä

Pienoismallien rakennus- ja

kaiverrussarja PMGS 12 C3

Q

Yleistä

Onnittelemme sinua hyvästä valinnastasi! Valitsit erit-

täin korkealaatuisen tuotteen. Käyttöohje on osa tätä

tuotetta. Se sisältää tärkeitä turvallisuusohjeita sekä

käyttöä ja hävitystä koskevia ohjeita. Tutustu ennen

tuotteen käyttöä huolellisesti kaikkiin käyttöja turval-

lisuusohjeisiin. Käytä tuotetta ainoastaan ohjeen

mukaan ja siinä mainittuihin tarkoituksiin. Anna kaikki

ohjeet mukaan, jos luovutat tuotteen edelleen.

Q

Määräystenmukainen käyttö

Pienporakonetta voidaan käyttää puun, metallin, muo-

vin, keramiikan tai kiven poraamiseen, jyrsimiseen,

kaivertamiseen, siistimiseen, hiomiseen, katkaisemi-

seen ja sahaamiseen kuivissa tiloissa. Jokaista muuta

käyttöä tai laitteen muutamista pidetään ei-määräys-

tenmukaisena ja sisältää huomattavia onnettomuus-

vaaroja. Määräystenvastaisesta käytöstä syntyneistä

vahingoista valmistaja ei ota mitään vastuuta.

Q

Varusteet

Pienoismallien rakennus- ja kaiverrussarja:

1

VirtakytKIN / KIERRosluvun säädin

2

Verkkolaitteen pistoke

3

Metallisanka

4

Kiinnitysrengas

5

Kiristysmutteri

6

Kiinnitysrengas LED-valolla

7

Karalukitus

Verkkolaite (katso kuva A):

8

Pistorasia pistotulpalle

2

9

Syvennys

10

Verkkolaite

11

Virtajohto (ja pistotulppa)

Tarvikkeet (katso kuva B):

12

6 HSS-poranterää

13

2 Kiristystuurnaa työkalun kiinnitykseen

14

3 Kiillotuslaikkaa

15

4 Hiomalaikkaa

16

1 Metalliharja

17

16 Erotuslaikkaa

18

5 Kiristyspihtiä

19

2 Muoviharjaa

20

3 Jyrsintäterää

21

2 Kaiverrusterää

22

5 Hiontaterää

23

1 Monitoimiavaimen

24

LED-valon virtakytkin

Q

Toimituslaajuus

1 Pienoismallien rakennus- ja kaiverrussarja

1 Verkkolaite

1 Muovilaukku

1 Tarvikesarja (50 osaa)

1 Kiinnitysrengas sis. paristot

1 Käyttöohje

Q

Tekniset tiedot

Pienoismallien rakennus- ja kaiverrussarja

PMGS 12 C3:

Nimellisjännite: 12 V

Nimellisottoteho: 22 W

Joutokäynnin kierrosluku: n 5000–20000 min

-1

Poran : maks. ø 3,2 mm

Levyhalkaisija: maks. ø 25 mm

Tarkastettu (mukaisesti): EN60745-1:2009/

A11:2010,

EN60745-2-1:2010,

EN60745-2-23:2013

Melu- ja tärinätiedot:

Melun mittausarvo laskettu EN 60745 standardin

mukaisesti. Sähkötyökalun A-mitattu melutaso on

tyypillisesti:

Äänenpainetaso: 57,3 dB(A)

Äänitehotaso: 68,3 dB(A)

Epävarmuus K: 3 dB

Arvioitu kiihtyvyys, tyypillisesti:

Käteen ja käsivarteen kohdistuva värinä: 0,817 m / s

2

Epävarmuus K = 1,5 m / s

2

Yleistä / Sähkötyökaluja koskevat yleiset turvaohjeet

Page is loading ...

Parkside 113362 Operation and Safety Notes

This manual is also suitable for

Parkside 113362 Operation and Safety Notes

in other languages

Related papers

Other documents