Consew CM-1200A User manual

Brand
Consew
Model
CM-1200A
Type
User manual

Consew CM-1200A is a heavy-duty commercial-grade automatic swatch cutting machine with a compact and convenient format. It features durable steel construction to ensure longevity and reliability. With its pneumatic air gauge and regulating valves, you can precisely adjust the pressure for even and clean cuts. The CM-1200A comes with two cutting boards, three M6 screws, an accessory plate, an Allen wrench, a pneumatic valve, a regulating foot, and a laser pointer for accurate fabric alignment.

Consew CM-1200A is a heavy-duty commercial-grade automatic swatch cutting machine with a compact and convenient format. It features durable steel construction to ensure longevity and reliability. With its pneumatic air gauge and regulating valves, you can precisely adjust the pressure for even and clean cuts. The CM-1200A comes with two cutting boards, three M6 screws, an accessory plate, an Allen wrench, a pneumatic valve, a regulating foot, and a laser pointer for accurate fabric alignment.

CM-1200 A
Automatic Swatch Cutting Machine
Instruction and Parts Manual
Chandler Machine USA, LLC.
Congratulations-
We would like to thank you and congratulate you for purchasing the Chandler
CM-1200A commercial grade swatch cutting machine from Chandler Machine
USA, LLC. With it’s heavy duty steel construction and commercial grade
components, the CM-1200A will allow you to obtain the benefits of commercial
swatch cutting in a compact and convenient format. For your safety and to fully
enjoy the advantages of this product, please take a few minutes to read the
assembly and safety instructions.
Sincerely,
Chandler Machine USA, LLC
Main Machine Fittings:
1.
Operation Table
2.
Cylinders (2)
3.
Pneumatic Air Gauge *
4.
Pneumatic Switch
5.
Main Blade
6.
Main Blade Screws (3)
7.
Pneumatic Valve
8. Regulating Valve
9. Air Hose (orange)
10.
Extra Plate *
11. Regulating Foot (4)
12. Cutting Board
5
12
4
8
2
1
3
6
7
9
10
11
Accessories:
•
2 Cutting Boards
•
1 Allen Wrench
•
3 M6 Screws
•
1 Accessory Plate
11
13.
Laser Pointer
14. Plastic Guard
15. Guide
* Air gauge attaches to right side
of machine.
* Extra plate may be attached
to rear of machine, as needed.
13
14
15
Assembly and Operation Instructions for CM-1200A
1. Remove the CM-1200A from it’s packing and put the swatch cutter on a flat
and solid surface.
2. Use the M6 Allen wrench to install the pneumatic air gauge (3), make sure the
M6 screws are secured tightly.
3. If desired, attach the extra plate on rear of machine.
4. Put cutting board (12) under the main blade (5) .
5. Connect the air hose (9) to the air pump and allow the pressure to increase
until it reaches between 6 and 8 bars.
6. Load the fabric under the cutting blade.
7. With both hands, press the pneumatic switches on each side of the swatch
cutter. * For your safety, never place body parts under the blade and always use
both hands to press the two pneumatic switches.
8. Remove fabric and load for another cutting cycle.
Note: Both cylinders must have the same amount of pressure so that the blade will
come down equally on both sides and fully cut the fabric. To change pressure,
adjust the regulating valves (8) on the back of each cylinder.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Consew CM-1200A User manual

Brand
Consew
Model
CM-1200A
Type
User manual

Consew CM-1200A is a heavy-duty commercial-grade automatic swatch cutting machine with a compact and convenient format. It features durable steel construction to ensure longevity and reliability. With its pneumatic air gauge and regulating valves, you can precisely adjust the pressure for even and clean cuts. The CM-1200A comes with two cutting boards, three M6 screws, an accessory plate, an Allen wrench, a pneumatic valve, a regulating foot, and a laser pointer for accurate fabric alignment.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents