Hunter Fan 24267 Owner's manual

Brand: Hunter Fan

Model: 24267

Type: Owner's manual

This manual is also suitable for

24967

42716-01 • 01/29/07

For Your Records and Warranty

Assistance

Model Name: _____________________

Catalog/Model No.: ________________

Serial No.: ________________________

Date Purchased: ___________________

Where Purchased: _________________

For reference also attach your receipt or a

copy of your receipt to the manual.

Table of Contents

1 • Getting Ready .....................................................4

2 • Assembling the Skirt .......................................5

3 • Assembling the Base .......................................6

4 • Assembling the Fan .........................................8

5 • Completing Assembly .................................10

6 • Operating and Cleaning Your Fan ........11

7 • Troubleshooting .............................................12

Welcome

Considering Optional Accessories

Hunter provides unique accessories speciﬁcally for use with this fan. An

accessory table and light kit are available from your local Hunter dealer

to further enhance your outdoor living environment.

is fan is intended for use ONLY with the following accessory models:

28493 Accessory Table

READ AND SAVE THESE INSTRUCTIONS.

Your new Hunter

fan is an addition to your

outdoor living environment that will provide

comfort and performance for many years.

is installation and operation manual gives

you complete instructions for assembling

and operating your fan.

We are proud of our work. We appreciate the

opportunity to supply you with the best fan

available anywhere in the world.

Before assembling your fan, for your records

and warranty assistance, record information

from the carton and Hunter nameplate

label (located on the top of the fan motor

housing) on the front cover of this manual.

Fan shown with Accessory Table 28493

(sold separately)

Hunter Fan Company 42716-01 • 01/29/07

Important Information

General & Location:

• Use ONLY Hunter replacement parts.

• is fan is intended for outdoor use ONLY. is fan is

suitable for wet locations. If the fan has been subjected

to extreme weather conditions, inspect before use.

• NEVER place a switch where it can be reached from a

wet surface.

• is fan MUST be assembled by two or more people.

Do NOT attempt to assemble this fan without

assistance.

• Make sure the installation site you choose allows the

fan blades to rotate without any obstructions within

6 feet (1.83 m ) of end of fan blades. A minimum

clearance of 7 feet (2.13 m ) from the ﬁnished surface

to the bottom edge of the fan blade is required.

• is fan is NOT to be used on, or within 6 feet (1.83 m)

of stairs.

Warnings:

• All wiring must be in accordance with national and local electrical

codes. If you are unfamiliar with wiring, you should use a qualiﬁed

electrician and not attempt to install the fan.

• Be sure to read this manual carefully before beginning installation and

save these instructions for later reference or warranty assistance.

• e appliance is not intended for use by young children or inﬁrm

persons without supervision. Young children should be supervised to

ensure that they do not play with the appliance.

• To reduce the risk of personal injury, assemble the fan according to

these instructions, and use only the hardware supplied.

• To reduce the risk of personal injury, do NOT bend the blade

attachment system when installing, balancing, or cleaning the fan.

NEVER insert foreign objects between rotating fan blades.

• To avoid possible electrical shock, before relocating your fan,

disconnect the power by unplugging the power cord from the

electrical outlet.

• To reduce the risk of electrical shock, keep fan at least 16 feet away

from pools and spas. NEVER place the fan where it can fall or (4.88 m)

be pulled into a pool or hot tub.

• ALWAYS keep power cord dry and out of water (puddles, pools,

fountains).

Cautions:

• Do NOT climb on pole or table (if applicable).

• Do NOT use an extension cord with this fan.

• Do NOT place objects on power cord.

• Do NOT operate if: a) the power cord or plug is damaged; b) the appliance malfunctions; or c) the unit has been damaged in any

manner. Contact your Hunter Fan retailer or national distributor or visit our website at http://www.hunterfanglobal.com.

• Do NOT assemble or operate this fan on unlevel ground. is fan may ONLY be placed on level decks, level patios, level ground or

similar ﬂat, level surfaces.

• Before each use, inspect the power cord for cuts, wear and/or abrasion marks. If any are found, or any wires are exposed, the

appliance should be serviced and the power cord replaced. Please contact Hunter® Fan Company’s Service Department. Do not

return to the retailer.

Read this entire manual

carefully before beginning

installation. Save these

instructions.

42716-01 • 01/29/07 Hunter Fan Company

1 • Getting Ready

To assemble this fan, be sure each person can do the following:

• Identify and connect electrical wires.

• Lift 50 pounds [22 kgs].

If you need help installing the fan, your Hunter fan dealer can direct

you to a licensed installer or electrician.

Gathering the Tools

You will need the following tools for assembling the fan:

• Standard screwdriver

• Phillips-head screwdriver

• Allen Wrench (included)

• 7/16” Wrench or pliers

Checking Your Fan Parts

Carefully unpack your fan to avoid damage to the fan parts. Check

for any shipping damage to the motor or fan blades. If any parts

are missing or damaged, contact your Hunter retailer or national

distributor.

Assembling Multiple Fans?

If you are assembling more than

one fan, keep the fan blades and

blade irons in sets, as they were

shipped.

ATTENTION:

is fan must be assembled by

two or more people. Do not

attempt to assemble this fan

without assistance.

is fan weighs approximately

100 lbs [45 kgs].

Hunter Fan Company 42716-01 • 01/29/07

2 • Assembling the Skirt

Note: is fan should be assembled in an open,

level area with a solid ground surface large

enough for the assembled fan.

2-1. Locate the base stand and place it on the ground at the location

where the fan will be operated.

2-2. Identify the skirt section with the 4

small screw holes around the power

cord channel and a notch in the inner

edge. Align the four holes in the skirt

section with the holes in the base

stand where the power cord is located,

then align the notch in the skirt

section with the raised tab on the base

stand. Partially install four base bolts

to attach the skirt section to the base stand. To ensure proper

spacing, do not tighten the bolts until all have been partially

installed.

Note: e remaining three skirt sections are identical and may be

installed in any order.

2-3. Align the four holes in the next skirt section with four holes in the base

stand. Partially install four base bolts. Repeat for the remaining skirt

sections.

CAUTION: Do not attempt to assemble fan without all four skirt sections. e fan may fall if a skirt section is not installed.

Skirt

Section

Base Stand

Power Cord

Channel

Base

Bolt

4 Small Screw Holes

Base Bolt

64193-02-247

(x 16)

Hardware Needed:

Steps 2-1 - 2-3:

Skirt Bolt

Skirt

Section

Skirt Bolt

06548-01-247

(x 16)

Hardware Needed:

Step 2-4:

2-4. Align the holes in each skirt bracket with the

adjoining skirt section and partially install

two skirt bolts. Repeat for all skirt sections.

2-5. After all skirt sections are properly aligned,

securely tighten all skirt bolts and base bolts.

Skirt

Bracket

42716-01 • 01/29/07 Hunter Fan Company

3 • Assembling the Base

3-1. Guide the power cord through the channel

and install the cover plate over the power cord

using four screws. Be sure the power cord is not

pinched between the channel and the cover plate.

Tab

Screw

Lower

Pole

Section

Lower

Pole

Bolt

Lower

Pole

Nut

Cover Plate

Screw

74506-59-247

(x 4)

Hardware Needed:

Lower Pole Bolt

06551-10-247

(x 2)

Hardware Needed:

Lower Pole Nut

06552-02-247

(x 2)

3-2. read the power cord through the lower pole section

and slide the lower pole onto the base stand. Align the

holes in the lower pole segment with the holes in the

base stand and securely install two lower pole bolts

with nuts to stabilize.

3-3. Being careful to not damage the fan ﬁnish, slide the

base cover onto the lower pole and let it rest on the

base stand.

3-4. Holding both the base stand and base cover,

carefully tilt the base assembly and rest the

assembly on its side to access the bottom of the

base. Align the two tabs on the base cover with the

two holes in the base stand. Install two screws to

secure the base cover to the base stand.

Steps 3-3 - 3-4:

Tab Screw

74513-54-247

(x 2)

Hardware Needed:

Step 3-1:

Step 3-2:

Power

Cord

Cover

Plate

Screw

Channel

Hunter Fan Company 42716-01 • 01/29/07

Middle

Pole

Section

Power

Cord

Base

Cover

Spindle

Cover

Base

Stand

Grommet

3 • Assembling the Base

Step 3-7:

Pole Screw

06549-01-247

(x 3)

Hardware Needed:

3-6. Holding the grommet in place, slide the spindle and spindle cover

onto the lower pole. Lower the spindle and spindle cover to rest on

the base cover.

Step 3-6:

3-7. read the power cord through the middle pole

section. Attach the middle pole section to the lower

pole section. Align the holes and securely install three

screws to stabilize.

3-5. With the assembly still on its side, install the

third foot into the base with the provided

screw. (e ﬁrst two have been preinstalled.)

When the ﬁnal foot has been installed, tilt the

assembly back to its upright position.

Step 3-5:

Foot Screw

74510-27-247

(x 1)

Hardware Needed:

Foot

Screw

Foot

Preinstalled feet

42716-01 • 01/29/07 Hunter Fan Company

4 • Assembling the Fan

Note: You may rest the fan body in the

carton for protection and stability during

this time.

4-1. Remove the blade iron screws and shipping

blocks from the fan motor. Save the screws

and discard the shipping blocks.

4-2. Install three grommets into the holes in

each blade. Align the holes in the blade with

the holes in the blade iron and attach with

three blade screws. Securely tighten the

screws.

Note: e blades may appear loose when

fully attached. is is normal.

Blade

Iron

Screw

Upper

Switch

Housing

Blade Screw

63730-08-247

(x 15)

Hardware Needed:

Blade Iron

Screw

63755-06-247

(x 10)

Hardware Needed:

Upper Switch

Housing Screw

74514-60-247

(x 2)

Hardware Needed:

Steps 4-1 - 4-2:

Step 4-3:

4-3. Partially attach each blade assembly to the fan with

two blade iron screws. When all blades are attached

and properly spaced, securely tighten all screws.

4-4. Unbundle the wires from the fan. read

the wires from the fan through the hole

in the upper switch housing. Attach the

upper switch housing to the fan using two

screws.

Step 4-4:

Blade

Screw

Blade

Grommet

Blade

Iron

Hunter Fan Company 42716-01 • 01/29/07

Screw

Boss

Upper Pole

Segment

Lower

Switch

Housing

Screw

Grommet

Upper Pole

Screw

74506-54-247

(x 4)

Hardware Needed:

Switch Housing

Screw

64555-05-247

(x 3)

Hardware Needed:

4-5. read the power cord with the 3-pin plug connector

from the fan through the upper pole segment.

4 • Assembling the Fan

4-6. Pull the 9-pin plug connector through the side

of the upper pole segment. Align the holes in the

upper pole segment with the bosses in the upper

switch housing. Install four screws to secure the

upper pole segment to the fan.

Note: If you are installing an accessory light kit,

refer to the manual included with the light kit for

assembly instructions at this time.

Step 4-5:

Step 4-6:

4-7. Being careful not to damage the fan ﬁnish, slide

the lower switch housing onto the upper pole

segment holding the grommet in place. Connect

the 9-pin plug connector from the fan to the

9-pin plug connector from the lower switch

housing.

4-8. Align the holes in the side of the lower switch

housing with the holes in the upper switch

housing and securely install three switch housing

screws.

Steps 4-7 - 4-8:

9-Pin

Plug

Con-

nector

42716-01 • 01/29/07 Hunter Fan Company

5 • Completing Assembly

Note: Be sure there are no obstructions before lifting

the fan to complete assembly.

5-1. Being careful to not pinch any wires, lift the fan and

upper pole assembly and place it onto the middle pole

segment to align the window in the upper pole with the

window in the middle pole.

5-2. Connect the 3-pin plug connector from the fan to the

3-pin plug connector from the base. Push the wires into

the pole.

CAUTION: Do not attempt to assemble fan without all three pole

segments.

Window

Open

Screw

Upper

Pole

Segment

Logo

Coverplate

Screw

Window

Closed

Pole Screw

06549-01-247

(x 1)

Hardware Needed:

Pole Screw

06549-01-247

(x 2)

Hardware Needed:

5-3. Be sure no wires are pinched before

closing the window. Rotate the upper pole

segment 180

to align the screw holes and

close the window.

5-4. Align the holes with the logo coverplate

and securely install two screws.

Steps 5-1 - 5-2:

Steps 5-3 - 5-4:

5-5. Install the remaining screw behind the logo coverplate.

Securely tighten all screws.

Step 5-5:

Hunter Fan Company 42716-01 • 01/29/07

6 • Operating and Cleaning Your Fan

6-1. Plug the fan into an electrical outlet.

6-2. e fan pull chain controls power to the fan.

e pull chain has four settings in sequence: High,

Medium, Low and Oﬀ.

• Pull the chain slowly to change settings.

• Release slowly to prevent the chain from

recoiling into the blades.

6-3. Install the included plugs into the remaining holes in the

poles. e holes are for an accessory table, which may be

purchased separately.

6-4. is fan operates in a downdraft direction only by blowing

air downward (counterclockwise blade rotation) to cool the area

with a direct breeze.

Note: Do not use a water hose or pressure washer to clean

this fan.

6-5. For cleaning ﬁnishes, use a soft brush or lint-free cloth to prevent

scratching. A vacuum cleaner brush nozzle can remove heavier

dust. Remove surface smudges or accumulated dirt and dust

using a mild detergent and a slightly dampened cloth. You may

use an artistic agent, but never abrasive cleaning agents as they

will damage the ﬁnish.

Completed Assembly

93” (2.3 m)

42716-01 • 01/29/07 Hunter Fan Company

7 • Troubleshooting

Problem: Nothing happens; fan does not move.

1. Turn power on, replace fuse, or reset breaker.

2. Check the plug connections in the switch housing.

3. Pull the pull chain to ensure it is on.

4. Remove the shipping bumpers.

5. Ensure that the fan is plugged into a suitable GFCI outlet.

Problem: Noisy operation.

1. Tighten the blade iron screws until snug.

2. Tighten the blade screws until snug.

3. Check to see if the blade is cracked. If so, replace all the blades.

4. Check and tighten the screws in the switch housing mounting

plate and in the upper and lower switch housing.

Problem: Excessive wobbling.

1. If your fan wobbles when operating, use the enclosed balancing

kit and instructions to balance the fan.

2. Tighten all blade and/or blade iron screws.

3. Tighten all skirt and base screws.

4. Make sure all three rubber feet are installed under the base.

If you need parts or service assistance, please visit

http://www.hunterfanglobal.com or contact your

national distributor.

Hunter Fan Company

2500 Frisco Avenue

Memphis, Tennessee 38114

Hunter Fan Company 42716-01 • 01/29/07

Hunter Fan 24267 Owner's manual

Brand: Hunter Fan

Model: 24267

Type: Owner's manual

This manual is also suitable for

24967

Download PDF

report

Hunter Fan 24267 Owner's manual

This manual is also suitable for

Hunter Fan 24267 Owner's manual

Related papers

Other documents