Kingston Technology K1333D3LD4R9S8G Datasheet

Kingston Technology
Brand
Kingston Technology
Model
K1333D3LD4R9S8G
Category
Memory modules
Type
Datasheet

Kingston Technology K1333D3LD4R9S8G is a reliable memory module designed to enhance the performance of your computer system. It features a 2Rx4 1G x 72-Bit architecture and operates at a speed of PC3-10600, providing fast and efficient data transfer rates. With a capacity of 8GB and a registered design, this memory module is ideal for handling large datasets and demanding applications. Additionally, it supports error correction code (ECC), ensuring data integrity and reducing the risk of errors.

Kingston Technology K1333D3LD4R9S8G is a reliable memory module designed to enhance the performance of your computer system. It features a 2Rx4 1G x 72-Bit architecture and operates at a speed of PC3-10600, providing fast and efficient data transfer rates. With a capacity of 8GB and a registered design, this memory module is ideal for handling large datasets and demanding applications. Additionally, it supports error correction code (ECC), ensuring data integrity and reducing the risk of errors.

KVR1333D3LD4R9S/8G
8GB 2Rx4 1G x 72-Bit PC3-10600
CL9 Registered w/Parity 240-Pin DIMM
DESCRIPTION
This document describes ValueRAM's 1G x 72-bit (8GB)
DDR3L-1333 CL9 SDRAM (Synchronous DRAM), low voltage,
registered w/parity, 2Rx4 ECC memory module, based on
thirty-six 512M x 4-bit DDR3L-1333 FBGA components. The
SPD is programmed to JEDEC standard latency DDR3-1333
timing of 9-9-9 at 1.5V. This 240-pin DIMM uses gold contact
fingers. The electrical and mechanical specifications are as
follows:
Note: This module may include a full-DIMM heat spreader.
FEATURES
• JEDEC standard 1.35V (1.28V ~ 1.45V) and 1.5V (1.425V ~
1.575V) Power Supply
• VDDQ = 1.35V (1.28V ~ 1.45V) and 1.5V (1.425V ~ 1.575V)
• 667MHz fCK for 1333Mb/sec/pin
• 8 independent internal bank
• Programmable CAS Latency: 9, 8, 7, 6
• Programmable Additive Latency: 0, CL - 2, or CL - 1 clock
• Programmable CAS Write Latency(CWL) = 7 (DDR3-1333)
• 8-bit pre-fetch
• Burst Length: 8 (Interleave without any limit, sequential with
starting address “000” only), 4 with tCCD = 4 which does not
allow seamless read or write [either on the fly using A12 or
MRS]
• Bi-directional Differential Data Strobe
• Internal(self) calibration : Internal self calibration through ZQ
pin (RZQ : 240 ohm ± 1%)
• On Die Termination using ODT pin
• On-DIMM thermal sensor (Grade B)
• Average Refresh Period 7.8us at lower than TCASE 85°C,
3.9us at 85°C < TCASE < 95°C
• Asynchronous Reset
• PCB : Height 1.180” (30.00mm), double sided component
Document No. VALUERAM0950-001.B00 07/11/11 Page 1
Memory Module Specifi cations
SPECIFICATIONS
CL(IDD) 9 cycles
Row Cycle Time (tRCmin) 49.5ns (min.)
Refresh to Active/Refresh 160ns (min.)
Command Time (tRFCmin)
Row Active Time (tRASmin) 36ns (min.)
Power (Operating) (1.35V) = TBD*
(1.50V) = TBD*
UL Rating 94 V - 0
Operating Temperature 0
o
C to 85
o
C
Storage Temperature -55
o
C to +100
o
C
*Power will vary depending on the SDRAM and
Register/PLL used.
Continued >>
MODULE DIMENSIONS:
Document No. VALUERAM0950-001.B00 Page 2
(Units = millimeters)
  • Page 1 1
  • Page 2 2

Kingston Technology K1333D3LD4R9S8G Datasheet

Kingston Technology
Brand
Kingston Technology
Model
K1333D3LD4R9S8G
Category
Memory modules
Type
Datasheet

Kingston Technology K1333D3LD4R9S8G is a reliable memory module designed to enhance the performance of your computer system. It features a 2Rx4 1G x 72-Bit architecture and operates at a speed of PC3-10600, providing fast and efficient data transfer rates. With a capacity of 8GB and a registered design, this memory module is ideal for handling large datasets and demanding applications. Additionally, it supports error correction code (ECC), ensuring data integrity and reducing the risk of errors.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents