Medtronic INVOS 5100C User manual

Type
User manual

This manual is also suitable for

INVOS
®
Cerebral / Somatic Oximeter
GCX Mounting Solutions
The following describes the options available to mount the INVOS 5100C to anesthesia
machines, perfusion pumps and portable stands using a GCX Mounting System.
GCX Mounting System options available from Covidien:
INVOS 5100C Adapter Plate (Covidien P/N 5100C-GCX)
The Adapter Plate consists of a 4.80” x 5.0” steel adapter plate. The Adapter Plate is
for use with GCX Mounting Systems accommodating a bottom mounted device and
slide-in mounting plate.
INVOS 5100C Swivel Arm (Covidien P/N 5100C-SA)
The Swivel Arm consists of a GCX M-Series 8 Inch Articulating Arm with Slide-in
Mounting Plate, V-Block Mounting System with Socket Head Cap Screws (SHCS),
Hex Key and INVOS 5100C Adapter Plate. The Swivel Arm is for use to pole mount
(up to 2 inch diameter) instruments up to 25 lbs. (11.3 kg).
Adapter Plate Assembly Instructions
Tools required: Medium Phillips Screwdriver
1. Place the INVOS monitor on a clean padded surface with the display face down.
2. Remove all four screws (#8-32x1/2”, SS, CSHCS, Phillips, Flat Head, Nylok) from the
INVOS monitor’s round base plate.
3. Remove the round base plate from the mounting cylinder.
4. Secure the Adapter Plate to the mounting cylinder using the same four screws
(#8-32x1/2”, SS, CSHCS, Phillips, Flat Head, Nylok). Be careful not to overtighten the
screws.
#8-32x1/2”, SS, CSHCS,
Phillips, Flat Head, Nylok
Adapter Plate
Mounting Cylinder
Swivel Arm Assembly Instructions
1. Assemble the Adapter Plate to the INVOS monitor.
2. Attach the Swivel Arm to pole using enclosed Hex Key and V-Block mounting
system with socket head cap screws.
3. Adjust the Swivel Arm Mounting Plate. Evenly tighten or loosen the Adjustment
Screws with the Hex Key provided.
4. Align the Adapter Plate at the bottom of the INVOS monitor to the Swivel Arm
Mounting Plate. Slide the INVOS monitor into the plate until it stops at the
Spring Plunger (located below the Mounting Plate). Pull the Spring Plunger
and continue to slide the INVOS monitor until the mounting adapter engages
the Spring Plunger. Tighten the Locking Screws located on the underside of the
Mounting Plate.
Covidien llc, 15 Hampshire Street Manseld, MA 02048 Phone: 800-635-5267 www.covidien.com
©2010 Covidien. All rights reserved.
“Reecting the color of life” is a trademark of a Covidien company. Somanetics, INVOS and SomaSensor are registered trademarks of a Covidien company. GCX is a registered trademark of GCX Corporation. (www.gcx.com)
P/N 313407 Rev. B
Socket Head
Cap Screws (4)
Spring Plunger
Mounting Plate
Adjustment Screws
Locking Screws
Cable
Management
with Flexible
Covers
V-Block Mounting System
V-Block mounting for V-Block mounting for
3/4”-1” Diameter Poles 1-1/2” - 2” Diameter Poles
  • Page 1 1
  • Page 2 2

Medtronic INVOS 5100C User manual

Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI