Digimerge ACCP2SATA User manual

Digimerge
Brand
Digimerge
Model
ACCP2SATA
Type
User manual

Digimerge ACCP2SATA is a PATA-to-SATA converter that allows you to connect a SATA hard drive to a PATA interface. This can be useful if you want to upgrade your DVR system to a SATA hard drive, or if you need to connect a SATA hard drive to an older system that only has PATA interfaces.

The ACCP2SATA converter is compatible with the following systems:

  • DVR: DHU500R Series, D17800 Series
  • LCD DVR: L500 Series, SG17LD800 Series, SG19LD800 Series

To use the ACCP2SATA converter, simply attach it to the SATA hard drive and then connect the PATA data and power cables to the converter. The converter will then allow the SATA hard drive to be used with the PATA interface.

Digimerge ACCP2SATA is a PATA-to-SATA converter that allows you to connect a SATA hard drive to a PATA interface. This can be useful if you want to upgrade your DVR system to a SATA hard drive, or if you need to connect a SATA hard drive to an older system that only has PATA interfaces.

The ACCP2SATA converter is compatible with the following systems:

  • DVR: DHU500R Series, D17800 Series
  • LCD DVR: L500 Series, SG17LD800 Series, SG19LD800 Series

To use the ACCP2SATA converter, simply attach it to the SATA hard drive and then connect the PATA data and power cables to the converter. The converter will then allow the SATA hard drive to be used with the PATA interface.

Copyright © 2009 Lorex Technology Inc.
Figure 1.0 Attach the PATA-to-SATA
converter to the new SATA HDD
Use the PATA-to-SATA converter to convert your existing PATA DVR to a SATA interface.
Use the PATA-to-SATA Converter is compatible with the following systems:
DVR: LCD DVR:
ACCP2SATA ACCP2SATA-SG19
DHU500R Series D17800 Series
L500 Series SG17LD800 Series
SG19LD800 Series
Using the PATA to SATA Converter
ACCP2SATA
NOTE: If your system uses two hard drives, you will need an additional PATA-to-SATA Converter.
1. Power off your DVR system.
2. Carefully remove the SATA hard drive and mounting bracket
according the steps outlined in your system’s instruction
manual.
3. Attach the PATA to SATA Converter to the new SATA hard drive
(not included) (see figure 1.0).
NOTE: The PATA to SATA Converter can only connect one way.
Make sure the converter is firmly connected to the SATA hard
drive.
4. Insert the SATA HDD with converter into the mounting bracket.
PATA-TO-SATA
CONVERTER
Instruction Manual
English Version 1.0
CONTENTS
1. PATA-to-SATA Converter (x1)
2. Fastening Screws (x 2)
PATA-TO-SATA CONVERTER
FASTENING
SCREWS
MOUNTING PLATE FOR LCD DVR
(Included with ACCP2SATA-SG19 only)
Using the PATA to SATA Converter
2
Figure 1.1 Fasten the PATA-to-SATA
Converter to the bracket using the
included screws
Figure 1.2 Complete HDD with PATA-to-SATA Converter
(ACCP2SATA)
Figure 1.3 Complete HDD with PATA-to-
SATA Converter (ACCP2SATA—SG19)
The converter will slide over the bracket.
5. Secure the PATA to SATA Converter to the mounting bracket and HDD using the included screws (see
figure 1.1).
NOTE: The included screws are longer than the screws used in your DVR system. This allows the PATA-to-
SATA converter to be fastened securely to the mounting plate.
6. Connect the PATA data and power cables to the converter.
7. Replace the hard drive and mounting bracket to your system.
8. Power on your system and format the new hard drive.
NOTE: If using two hard drives, first format HDD 1, then format
HDD 2.
ACCP2SATA—SG19
1. Power off your DVR system.
2. Carefully remove the mounting plate from the rear panel of the system.
3. Disconnect the power and data cables from the hard drive.
4. Attach the PATA to SATA Converter to the new SATA hard drive (not included) (see figure 1.0).
NOTE: The PATA to SATA Converter can only connect one way. Make sure the converter is firmly connected
to the SATA hard drive.
5. Insert the SATA HDD with converter into the included mounting
plate. The converter will slide over the plate.
6. Secure the PATA to SATA Converter to the mounting bracket
and HDD using the included screws. Carefully line up the
converter and HDD with the mounting plate.
NOTE: The included screws are longer than the screws used in
your DVR system. This allows the PATA-to-SATA converter to be
fastened securely to the mounting plate.
7. Connect the PATA data and power cables to the converter.
8. Replace the hard drive and mounting plate to the rear panel of the system.
9. Power on your system and format the new hard drive.
  • Page 1 1
  • Page 2 2

Digimerge ACCP2SATA User manual

Digimerge
Brand
Digimerge
Model
ACCP2SATA
Type
User manual

Digimerge ACCP2SATA is a PATA-to-SATA converter that allows you to connect a SATA hard drive to a PATA interface. This can be useful if you want to upgrade your DVR system to a SATA hard drive, or if you need to connect a SATA hard drive to an older system that only has PATA interfaces.

The ACCP2SATA converter is compatible with the following systems:

  • DVR: DHU500R Series, D17800 Series
  • LCD DVR: L500 Series, SG17LD800 Series, SG19LD800 Series

To use the ACCP2SATA converter, simply attach it to the SATA hard drive and then connect the PATA data and power cables to the converter. The converter will then allow the SATA hard drive to be used with the PATA interface.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents