Bogen ASTB4 User manual

ASTB4
Bogen
Brand
Bogen
Model
ASTB4
Type
User manual

This manual is also suitable for

Bogen ASTB4 terminal boots offer added protection against weather effects on wires and connections of NEAR A-Series speaker models A2, A6, and A8. The package includes 4 boots designed to fit snugly over wire bundles. Installation involves trimming the boot sleeve to accommodate the wire size, securing wires to terminals, and sliding the boot over the terminals for a secure fit. Note that the boot fits only in one orientation and may require adjustment for the A2 model. While the boot minimizes weather impact, it doesn't provide a watertight seal.

Bogen ASTB4 terminal boots offer added protection against weather effects on wires and connections of NEAR A-Series speaker models A2, A6, and A8. The package includes 4 boots designed to fit snugly over wire bundles. Installation involves trimming the boot sleeve to accommodate the wire size, securing wires to terminals, and sliding the boot over the terminals for a secure fit. Note that the boot fits only in one orientation and may require adjustment for the A2 model. While the boot minimizes weather impact, it doesn't provide a watertight seal.

Description
The A-Series Terminal Boot is designed to offer added protection against the effects of
weather on wires and connections made to NEAR A-Series speaker model types A2, A6,
and A8. The ASTB4 package contains 4 terminal boots.
Note: The ASTB4 will not fit the NEAR A12 model.
Installation
1. If necessary, trim the tapering boot sleeve to accommodate the size of the wire bundle
to be attached to the speaker (adjust for a snug fit).
2. Slide the narrow end of the boot sleeve over the wires. Crimp any lugs onto the wires
after inserting the wires through the boot sleeve.
3. Secure the wires to the terminals and then slide the terminal boot into place over the
terminals, pressing it firmly against the terminal strip for a secure fit. The boot only fits
properly in one orientation.
Additional Protection
The terminal boot does not provide a water tight seal for the terminal strip. It is only
designed to minimize the direct effects of weather on the wires and connections.
Silicone-based caulks can be used to improve the seal of the boot to the speaker terminal
area. If desired, apply a bead to the base of the boot before pressing it onto the terminal.
Silicone sealents with adhesive properties adhere better than pure silicone products. The
boot sleeve exit can also be sealed, however, be certain to caulk it so that the caulk can
be removed later in case the boot needs to be removed.
Specifications subject to change without notice.
© 2002 Bogen Communications, Inc.
54-2085-01B 1104
50 Spring Street, Ramsey, NJ 07446, U.S.A.
Tel. 201-934-8500 • Fax: 201-934-9832
www.bogen.com
Model ASTB4
A-SERIES SPEAKER
TERMINAL BOOT
Note: The A2 speaker model does not allow enough space between the housing and the
bracket for the boot sleeve to pass between them. Therefore, it is important to install
the boot while the speaker is in its approximate final tilt position.
Description
The A-Series Terminal Boot is designed to offer added protection against the effects of
weather on wires and connections made to NEAR A-Series speaker model types A2, A6,
and A8. The ASTB4 package contains 4 terminal boots.
Note: The ASTB4 will not fit the NEAR A12 model.
Installation
1. If necessary, trim the tapering boot sleeve to accommodate the size of the wire bundle
to be attached to the speaker (adjust for a snug fit).
2. Slide the narrow end of the boot sleeve over the wires. Crimp any lugs onto the wires
after inserting the wires through the boot sleeve.
3. Secure the wires to the terminals and then slide the terminal boot into place over the
terminals, pressing it firmly against the terminal strip for a secure fit. The boot only fits
properly in one orientation.
Additional Protection
The terminal boot does not provide a water tight seal for the terminal strip. It is only
designed to minimize the direct effects of weather on the wires and connections.
Silicone-based caulks can be used to improve the seal of the boot to the speaker terminal
area. If desired, apply a bead to the base of the boot before pressing it onto the terminal.
Silicone sealents with adhesive properties adhere better than pure silicone products. The
boot sleeve exit can also be sealed, however, be certain to caulk it so that the caulk can
be removed later in case the boot needs to be removed.
Specifications subject to change without notice.
© 2002 Bogen Communications, Inc.
54-2085-01B 1104
50 Spring Street, Ramsey, NJ 07446, U.S.A.
Tel. 201-934-8500 • Fax: 201-934-9832
www.bogen.com
Model ASTB4
A-SERIES SPEAKER
TERMINAL BOOT
Note: The A2 speaker model does not allow enough space between the housing and the
bracket for the boot sleeve to pass between them. Therefore, it is important to install
the boot while the speaker is in its approximate final tilt position.
  • Page 1 1

Bogen ASTB4 User manual

ASTB4
Bogen
Brand
Bogen
Model
ASTB4
Type
User manual
This manual is also suitable for

Bogen ASTB4 terminal boots offer added protection against weather effects on wires and connections of NEAR A-Series speaker models A2, A6, and A8. The package includes 4 boots designed to fit snugly over wire bundles. Installation involves trimming the boot sleeve to accommodate the wire size, securing wires to terminals, and sliding the boot over the terminals for a secure fit. Note that the boot fits only in one orientation and may require adjustment for the A2 model. While the boot minimizes weather impact, it doesn't provide a watertight seal.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents