Special Instructions for
DS1100 SH2347 and DS2200 SH2348
10 - 30 Vdc
Electrical Connections
The scanner cable is equipped with a 25-pin female D-sub connector for
connection with the power supply and input/output signals:
Figure 1 – 25-pin female D-sub connector
25-pin D-sub connector pinout
Pin Name Function
9,13 VS Power supply input voltage +
25 GND Power supply input voltage -
1 * CHASSIS Chassis Ground
2, 21 TXAUX TX RS232 Aux. Interface
3, 20 RXAUX RX RS232 Aux. Interface
4 RTX485 - RTX- RS485 Main Interface
5 RTX485 + RTX+ RS485 Main Interface
7 SGND Signal Ground
8 OUT1 + Output 1 +
11 OUT2 + Output 2 +
18 EXT TRIG + External trigger +
19 EXT TRIG - External trigger -
10, 12, 22 I/O REF Input/Output reference
17 IN1 - Input 1 -
6, 14, 15, 16, 23, 24 N.C. Not Connected
* Pins 1 and 25 are connected together internally.
851000292 (Rev. B)
Power Supply
Power can be supplied to the scanner through the pins provided on the
25-pin connector used for communication with the host.
The power must be between 10 and 30 Vdc only.
13/9
25
1
VS
GND
CHASSIS
USER INTERFACE
GND
V+ (10 - 30 Vdc)
SCANNER
Inputs
The yellow LED is on when the External Trigger forces a current flow
through the EXT TRIG+ and EXT TRIG- pins.
This input is optocoupled and can be driven by both an NPN or PNP type
command. The connections are indicated in the following diagrams:
EXT TRIG+
18
19
+ 5V
SCANNER
EXTERNAL TRIGGER
Signal
V
30 Vdc max.
Vext
EXT TRIG-
Figure 2 - Input NPN command using external power
EXTERNAL TRIGGERSCANNER
Signal
18
19
+ 5V
VS
9
25
GND
Ground
V
EXT TRIG+
EXT TRIG-
Figure 3 - Input NPN command using scanner power
18
19
+ 5V
SCANNER
EXTERNAL TRIGGE
R
30 Vdc max.
V
ext
V
Signal
Ground
EXT TRIG+
EXT TRIG-
Figure 4 - Input PNP command using external power
EXTERNAL TRIGGERSCANNER
18
19
+ 5V
VS9
25
GND
Ground
V
Signal
EXT TRIG+
EXT TRIG-
Figure 5 - Input PNP command using scanner power
For DS1100, the general purpose input IN1 is used in the Standard
Application Program to store the code verifier (see “Store Verifier HW” in the
WinHost Help On Line). Use the input connections indicated in the figure
below. For DS2200, this input is not used.
13/9
17
VS
IN1 -
22
I/O REF
USER INTERFACE
Ground
V
SCANNER
47 K
Figure 6 - IN1 - Input command
-
1
-
2
Datalogic DS2200 SH2348 User manual
- Type
- User manual
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Datalogic DS1100-2101 HI-RES User manual
-
Datalogic Scanning DS2200 User manual
-
Datalogic Scanning DS1100 User manual
-
Datalogic DS4300 Installation guide
-
Datalogic Scanning C-BOX 150 User manual
-
Datalogic DS2400N Reference guide
-
-
Datalogic Scanning Barcode Reader DS4300 User manual
-
-