ESAB All Cutmaster True Troubleshooting instruction

All Cutmaster True
ESAB
Brand
ESAB
Model
All Cutmaster True
Type
Troubleshooting instruction

This manual is also suitable for

ESAB All Cutmaster True is a versatile plasma cutter designed for precise and clean cutting of various metals. With its advanced inverter technology, it delivers exceptional performance, allowing users to make quick and accurate cuts on mild steel, stainless steel, and aluminum up to 1/2 inch thick. It features simple controls, a user-friendly interface, and a built-in air compressor, making it easy to set up and operate. Its compact and portable design ensures easy maneuverability and storage.

ESAB All Cutmaster True is a versatile plasma cutter designed for precise and clean cutting of various metals. With its advanced inverter technology, it delivers exceptional performance, allowing users to make quick and accurate cuts on mild steel, stainless steel, and aluminum up to 1/2 inch thick. It features simple controls, a user-friendly interface, and a built-in air compressor, making it easy to set up and operate. Its compact and portable design ensures easy maneuverability and storage.

TECHNICAL
BULLETIN
Date: 8/1/2009
Product: All Cutmaster TRUE (except CM 39 and CM 10) By: John Brasseur
Subject: Input pressure upgrade
Summary: Input supply pressure to the True series caused faults below 55psi
1 of 2
THERMAL DYNAMICS TECHNICAL SUPPORT
Phone: 1-800-752-7622
Fax: 1-603-298-7402
tdc-tech@thermadyne.com
www.thermadyne.com
Form 0022
82 Benning Street
West Lebanon, NH 03784
1-603-298-5711
Fax: 1-800-221-4401
“Exceeding Customer Expectations Through Performance Excellence"
Valued Thermadyne Service Provider,
Thermal Dynamics is proud to introduce a pressure requirement upgrade to the Cutmaster True Series.
The old model of machines would initiate a fault condition if the input supply drops below 55 psi. Earlier series of
Cutmaster and PakMaster plasma systems had the trigger mechanism set at 45 psi. To remain consistent,
the firmware of the True Series has been modified to allow operation with input pressures down to 45 psi,
additionally the pressure is sampled and averaged over a longer period of time to prevent pressure faults
that occur while a compressor is regenerating.
The functionality is included in firmware version REV: 3.2.
Red error light
Low gas pressure light
TECHNICAL
BULLETIN
Date: 8/1/2009
Product: All Cutmaster TRUE (except CM 39 and CM 10) By: John Brasseur
Subject: Input pressure sensitivity
Summary: Input supply pressure to the True series caused faults below 55psi
2 of 2
THERMAL DYNAMICS TECHNICAL SUPPORT
Phone: 1-800-752-7622
Fax: 1-603-298-7402
tdc-tech@thermadyne.com
www.thermadyne.com
Form 0022
82 Benning Street
West Lebanon, NH 03784
1-603-298-5711
Fax: 1-800-221-4401
“Exceeding Customer Expectations Through Performance Excellence"
If you have a customer that is having issues with a machine operating at low line pressure, please contact
Thermal Dynamics for a up graded Logic PCB (part number 9-0107). While this impacts a small percentage of
applications, our intention is to add consistency and flexibility across the manual plasma product line.
Contact Thermadyne Technical Support at 1-800-752-7622 to request a replacement board and an RGA#.
We estimate that it will take a service person approximately 1 hour to remove the old logic board and replace
with the new one.
At initial power up, two lights will temporarily
illuminate for 2-3 seconds to show the version
of software used.
To determine the first digit, count the function
Indicators left to right, “1 through 5”.
To determine the second digit count the
pressure indicators, reading from bottom to top,
“0 through 7”.
Example of the front display indicating the 3.2 firmware
version
  • Page 1 1
  • Page 2 2

ESAB All Cutmaster True Troubleshooting instruction

All Cutmaster True
ESAB
Brand
ESAB
Model
All Cutmaster True
Type
Troubleshooting instruction
This manual is also suitable for

ESAB All Cutmaster True is a versatile plasma cutter designed for precise and clean cutting of various metals. With its advanced inverter technology, it delivers exceptional performance, allowing users to make quick and accurate cuts on mild steel, stainless steel, and aluminum up to 1/2 inch thick. It features simple controls, a user-friendly interface, and a built-in air compressor, making it easy to set up and operate. Its compact and portable design ensures easy maneuverability and storage.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents