Worx WG712 Owner's manual

Brand: Worx

Model: WG712

Category: Lawnmowers

Type: Owner's manual

Page is loading ...

t. SWilTCH LEVER

2. SAFETY BUTTON

3. UPPER HANDLE

4. UPPER HANDLE KNOB

5. MOTOR COVER

G. HEIIGHT OF CUT LEVER

7. BLADE BOLT (See L)

S. GRASS BOX

9. SAFETY FLAP

10. GRASS BOX HANDLE

111. MnDDLE CARRY HANDLE

12. FRONT CARRY HANDLE

113. RUtDE (See K )

t 4. CABLE CLIPS

15. LOWER HANDLE

16. LOW HANDLE KNOBS

t 7. LOWER HANDLE BRACKET

8. HNSPECTaON WIlNDOW

19. MULCHONG INSERT

TECHNKCAL U TA

Rated Voltages: 120V-60Hz

Rated Power: 13,0A

Rated No load Speed: 3500/min

Cutting Diameter: 16"

Cut Height: 3/4" - 2-3/4"

Cut Height Adjustment : 6

Grass Collection Capacity: 1.4 Bushels

MachineWei ht: 43.6 Ibs (19.8Kg)

#ARXI (} LIST

Grassbox (2 halues) 11PC Grassbox handle screws 4PC

Handle knobs 2PC Mulching insert 1PC

erasshox handle I PC Cable clips 2PC

We recommend that you buy all your accessories from the store where you purchased the tool,

Use good quality accessories with a well known brand name,, Store personnel can also help and

advise°

NA-WG712-M-070115, indd 6

2007-1-15 16:52:57

SAFE IN$TRUCTHON$

WARNBNG! Read All Instructions when

using electric gardening appliances.

Basic safety precautions should always be

followed to reduce the risk of fire, electric shock,

and personal injury, including the following:

FOR ALL DOUBLE-nNSULATED

APPILL41NCES

Replacement pa_s. When servicing use

only identical replacement parts°

Polarized Appliance Connections

To reduce the risk of electric shock, this

appliance has a polarized plug (one blade

is wider than the other) and will require

the use of a polarized extension cord°

The appliance plug wilt fit into a polarized

extension cord only one way. If the plug

does not fit fully into the extension cord,

reverse the plug.. If the plug still does not fit,

obtain a correct polarized extension cord. A

polarized extension cord will require the use

of a polarized wall outlet,. This plug will fit

into the polarized wall outlet only one way. If

the plug does not fit fully into the wall outlet,

reverse the plug. If the plug still does not

fit, contact a qualified electrician to install

the proper wall outlet Do not change the

equipment plug, extension cord receptacle,

or extension cord plug in any way,

2. FOR ALL APPLEANCES

a) Avoid dangerous environment. Don't

use appliances in damp or wet locations_

b} Don't use in rain.

c) Keep chi|dren away. All visitors should be

kept at a distance from work area_

d) Dress proper_. Do not wear loose

clothing or jewelry.. They can be caught in

moving parts.. Use of protective gloves and

substantial footwear is recommended when

working outdoors.. Wear protective hair

covering to contain long hair.,

e) Use safety glasses. Always use face or

dust mask if operation is dusty.

f) Use right appl_iance. Do not use appliance for

any job except that for which it is intended,,

g) Ground Fauk Circuit Pnterrupter (GFCg)

protection should be provided on the

circuit(s) or outmet(s) to be used for

the gardening applia.ce. Receptacles

are available having built-in GFCt protection

and may be used for an added measure of

h )_ IJtIARNING! To

reduce the risk of

electric shock, use only with an extension

cord intended for outdoor use, such as an

extension cord of cord type SW-A, SOW-A,

STW-A, STOW-A, SJW-A, SJOW-A, SJTW-A_

or SJTOW-A_

i) _xtension cord! Make sure your extension

cord is in good condition,, When using an

extension cord, be sure to use one heavy

enough to carry the current your product

will draw_ An undersized extension cord will

cause a drop in line voltage resulting in loss

of power and overheating.Table I shows the

correct size to use depending on cord length

and nameplate ampere rating. If in doubt,

use the next heavier gage.The smaller the

gage number, the heavier the cordoTo reduce

the risk of disconnection of appliance cord

from the extension cord during operating:

i) Make a knot as shown in Figure 2; or

ii) Use one of the plug-receptacle retaining straps

or connectors described in this manual.

Table 1 Minimuna gauge for extension

cords

Ampere Rating

More than Not

more than

. 0-6

6-10

, 10-12 .......

12-16

Volts Total length of cord in feet

120V I 2s t 501i001 is0

_ 240V ....... 50 I i001 }00 I 300-

AmericanWrie Gauge

. 1# .... !6 16 f !2

18 16 14 12

16 16 : 14 12

Not recom-

14 12

mended

Figure I

Uethod of securing extension cord

Tie cord as shown

(B) connect p!ug and

j) Avoid unintentional starting. Don't carry

plugged-in appliance with finger on switch,

Be sure switch is off when plugging in..

l() Don't abuse cord. Never carry appliance

by cord or yank it to disconnect from

receptacle.. Keep cord from heat, oil, and

NA-WG712-M-070115 indd 7 2007q-15 16:52:58

sharp edges.

H) Don't grasp the exposed cutting blades

or cutting edges when picking up or

holding the appliance,

re|Don't force appJia.ce. It witl do the job

better and with less risk of injury at the rate

for which it was designed.

n) Dou't overreach. Keep proper footing and

balance at all times°

o) Stay alert. Watch what you are doing.

Use common sense. Do not operate

appliance when you are tire&

p} Disconnect appliance. Disconnect the

appliance from the power supply when not

in use, before servicing, when changing

accessories such as blades, and the like..

q) Store idle appliances indoors. When not

in use, appliances should be stored indoors

in dry, and high or locked-up place, out of

reach of children.

r) _aintaln appliance with care. Keep

cutting edge sharp and clean for best

performance and to reduce the risk of injury.

Follow instructions for lubricating and

changing accessories, Inspect appliance cord

periodically, and if damaged, have it repaired

by an authorized service facility. Inspect

extension cords periodically and replace if

damage& Keep handles dry, clean, and free

from oil and grease.

s) Check damaged parts. Before further use

of the appliance, a guard or other part that

is damaged should be carefully checked

to determine that it will operate properly

and perform its intended function. Check

for alignment of moving parts, binding of

moving parts, breakage of parts, mounting,

and any other condition that may affect

its operation. A guard or" other part that is

damaged should be properly repaired or

replaced by an authorized service center

unless indicated elsewhere in this manual..

t) Keep guards in place and in working

order.

u) Keep blades sharp.

v) Keep hands and feet away from cutting

area.

w)Objects struck by the lawn mower blade

can cause serve injuries to persons,

The lawn should always be carefully

examined and cleared of all objects prior to

each mowing_

x) Hf lawn mower strikes a foreign objectx

follow these steps:

i)Stop lawn mower. Release the switch.,

ii)Unplug power cord°

iii)lnspect for damage°

iv)Repair any damage before restarting and

operating the lawn mower,

y) Use identical replacement blades onHy.

z) Under norma! usage, the catcher

assembly is subject to deterioration

and wear and should, therefore, be

frequendy checked for replacement.

Any replacement assemhl V should be

checked for compliance with the original

manufacturer's recommendatio,s or

spot.canons.

/_ WARNHNG! Some dust created when

using lawn and garden power tools

contains chemicals known to cause cancer,

birth defects and other reproductive harm,

Some examples of these chemicals are:

crystalline silica from sand, bricks and other

masonry dust, arsenic and chromium from

chemically treated lumber (CCA), compounds

in fertilizer compounds, in insecticides,

herbicides and pesticides. Health risk from

these chemical exposures varies, depending on

the environment in which you are working and

how often you do this type of work.

When using lawn and garden power tools,

wear safety equipment such as gloves and dust

masks which are especially designed to filter

out microscopic particles.

V .Volts

A Amperes

Hz....................................... Hertz

no no load speed

.alternating current

[_ .... Class If construction / Double insulation

SYMBOLS

Warning

Read the instructions

(_ Wear eye protection

(_ o avoid possibility of electric

shock, do not expose to rain

/_ Remove plug from the power

supply immediately if cable is

damaged or cut

NA-WG712-M-O7O115indd 8 2007-1-t5 t6:52:59

AS$EMBLY

//_ impoi'_nt w.

Before you assemble the lawn mower,

check the packing fist on page 5, Make sure a!l

parts are included.

FJITTgNG THE LO_R HANDLE

(See A, B, C, D)

When removed from the box, the mower should

now look like fig AmFix the lower ha ndle brackets

(17) to the deck as fig B and align the handle as

fig C, Make sure that they are located properly

before inserting the lower handle knobs and

tighten clockwise.(See D) Lift the Upper handle

into position as shown in E,,Align handle and

tighten handle knob clockwise. Check that the

upper and lower handles are firmly secure,,

Ensure the cables do not become stuck when

foldinglunfolding Lower Handle

Note: Ensure that the cable clips (14)(See E)

supplied are used to fix the cable to the Lower

Handle (15)o(See B) Attach the cable clips and

make sure there is enough cable slack,,

G_u_SSBOX ASSEMBLY

(See F.t )

DO NOT OVERTIGHTENTHE SCREWS°

First connect the grass box handle (10) to the box

top using the four provided screws

Grassbox ASSEMBLY (See E2 and G )

Next, snap together the top and bottom grass

box halves by pushing all the "snap fits" together

around the edges; start from the rear and work

towards the front°

GRASSBOX

Fitting

Lift the safety flap (9) and insert grass box

(8)o(See H)

As the grassbox fills up, grass will be clearly

visible through the inspection window(18)(See

When the window is futl it its time to empty the

grassbox,

Removing/Emptying

Lift the safety flap (9) and hold up. Remove

grass box (8)°

MULCHING FEATURE

The mower is designed to mulch the grass

depending on whether mulching insert

(t9) is inserted (mulching) or the mulching

insert is out and the grassbox is in place ,,No

further assembly steps are required if you are

mulching_

1, Unplug mower, and wait for blade to come

to a complete stop,,

2., Raise the safety flap (9) and hold it up (See

H2)

3,, Lift and push in the mulching insert

completely(See H,3)

For non-grass collection, the mower can be

used without the grass box (8) in position, with

the safety flap (9) in the down position,,

'W'X_W'arning: Always check the safety flap

can close the discharge outlet tightly

before using, Never lift the safety flap (9) when

the lawn mower is being used without fitted

grass box°

8P :RATISN

STARTING AND STOPPRNG (See J)

STARTING

Connect the extension cord to the pigtail (See

J),Connect the plug to the power outlet and

switch ON_

The switchbox is provided with a lock-off button

to prevent accidental starting.

Press and hold the safety button (2)_ with

the other hand, squeeze the switch lever (1)

towards the handle,and release the safety lock

off buttonoThe machine is now started. Wait

until the blade is at full speed before cutting the

grass.

Use both hands to hold the switch lever to keep

the mower running°

STOPPING

Release the switch lever (1).

ADJUSTgNG THE CUTTING HEIGHT

(See iO

_ Warnlng: Before adjusting the

mower height, wait for the mower to

completely stop. Mower blades continue

to rotate after the machine is switched

off and a rotating blade can cause injury.

Wait until all machine components haue

NAoWG712_M_070115, indd 9 2007-1q5 16:53:00

completely stopped before touching

them.

Before your first cut, adjust the mower cutting

height to the desired position., The mower

can be set to one of six cutting heights, with

cutting heights between 3/4" and 2-3/4': To

adjust the cutting height, press the top of cut

lever (6) outwards, at the same time lift or

push down the mower until required height

is selected..

11o

It_OWIING

For' cutting convenience, it may be best to start

mowing at a point close to the power supply

and to work your way away from the supply.

Mow the lawn at a right angle from the power'

supply and place the power cable to side which

has already been cut.

_ Warning:When mowing do not allow

the motor to labor, particularly in

heaw conditions. When the motor labors,

the speed of the motor cJrops and you

will hear a change in the motor sound.

VJt_e, this occurs, stop mowiug. Release

the switch lever and raise the height of

cut. Failure to do so could damage the

machine.

Position

Height of cutting

3/4"

1-1/8"

1-9/16"

3 2"

2 2-3/8"

1 2-3/4"

MAINTENANCE

_ Warni, g: Stop mower aud remove

plug from the power supply before

removing the grass box.

Note:To ensure long and reliable service, carry

out the following maintenance procedures

regularly, Check for obvious defects such as

a loose, dislodged or damaged blade, loose

fittings, and worn or damaged components,

Check that the covers and guards are all

undamaged and are correctly attached to

mower. Carry out any necessary maintenance

or repairs before operating mower° If the

mower should happen to fail despite regular

maintenance, please call our customer helpline

for advice_

BLADE MJZ_gNTENANC= [See L]

Never cam/out any assembly operations

or adjustments w_th the power connected

to the mower. Airways ensure that the

power button is in the off position and

that the power plug is disconnected from

the supply. JUways handle the bgade with

care-sharp edges could cause injury. Use

gloves.

Follow these procedures to remove and replace

the blade. You will need protective gloves (not

provided) and a spanner wrench (not provided)

to remove the blade, Hold the blade (13) and

unscrew the blade bolt (7)anti clockwise using

a spanner wrench. Remove blade and attach

a new one to the blade bolt_ Ensure that the

blade is properly positioned as seen in Fig. K,

then firmly tighten the bolt. DO &lOT OVER

TIGHTEN.

Renew your metal blade after" 50hrs mowing or

2 years ,which ever is the sooner-regardless of

condition.

gf the blade is cracked or damaged replace

it with a new one.

STORAGE:

Rotate _dl=eUpper Handle knob to release

the upper handle.

Always ensure that the power button is in

the off position and that the power plug is

disconnnected from the supply.

Clean the exterior of the machine thoroughly

using a soft brush and cloth. Do not use water,

solvents or polishes. Remove all grass and

debris, especially from the ventilation slots.

Turn the machine on its side and clean the blade

area° If grass cuttings are compacted in the

blade area, remove with a wooden or plastic

implement°

Store the machine in a dry place, Do not place

other' objects on lop of the machine.

Rotate the Upper Handle knob (4) to release

the handle joint, it can be folded.You can carry

the mover by middle carry handle(l!} and front

carry handle{12).(See M.1,M.2)

To aid storage, loosen the lower handle knobs

(16} and fold the handles..

Ensure cables are not stuck or entangled when

NA-WG712-M-070115,indd 10 2007-1-15 I6:53:01

folding or unfolding handles_ Do not deep the

handles.

MAINTENANCE

After use, disconnect the machine from the

power supply and check for damage. Your

power tool requires no additional lubrication

or maintenance.There are no user serviceable

parts in your power tool. Electric mowers should

only be repaired by an authorized repairer. Use

only manufacturers recommended replacement

parts and accessories,.

Never use water or chemical cleaners to clean

your power tool Wipe clean with a dr,/cloth,

Always store your power tool in a dry place

out of the reach of children. Keep the motor

ventilation slots clean. Keep all working controls

free of dust. If you see some sparks flashing in

the ventilation slots, this is normal and will not

damage your power tool,.

ENVIROnMEnTAL

PROTECTISN

Waste electrical products must not be

disposed of with household waste,

Please recycle where facilities exist..

Check with your local authorities or retailer for

recycling advice,

WARRanTY STATEMENT

30 DAY Satisfaction Guarantee

If for any reason you are dissatisfied with any

WORX product, you can return the product

along with proof of purchase ,within 30 days for

a full refund°

If your WORX product becomes defective due

to faulty materials or workmanship within the

specified warranty period of;

24 months for DIY and light trade use, from the

date of purchase.

We guarantee to repair or replace all defective

parts free of charge, repair products subject

to fair wear and tear, free of charge, or at our

discretion, replace the unit free of charge

to ensure minimum inconvenience to the

customer_ Your warranty is subject to the

following conditions:

Proof of purchase date and a valid receipt is

produced.

The product has not been misused°

The product has not been used for Professional

purposes,,

Unauthorized persons have not attempted

repairs..

The product has not been used for hire

purposes°

The product has not sustained damage through

foreign objects, substances or accidents_

Damage is not a result of fitting non-approved

accessories.

To claim the guarantee, you will need to submit

proof of purchase to the seller or an authorized

repair agent..

You can check the location of your nearest

authorized repair agent by contacting us at:

Positec USA, lnco t t

Charlotte, NC 28216 USA

PHONE: 1-866-354-WORX (9679) (._

This warranty does not apply to accessories°

This warranty applies only to the original

purchaser and may not be transferred.

All repairs and replacement tools will be

covered by the limited warranty for the balance

of the warranty period from the date of the

original purchase.

All repairs must use genuine spare parts.

NA-WG712-M-070115,indd 11 2007_1_15 t 6:63:01

Page is loading ...

it's your nature

Printed in China

NA_WG712-M,,070115 fndd 28

2607-1-15 16:53:12

Worx WG712 Owner's manual

Brand: Worx

Model: WG712

Category: Lawnmowers

Type: Owner's manual

Download PDF

report

in other languages

français: Worx WG712 Le manuel du propriétaire
español: Worx WG712 El manual del propietario

Worx WG712 Owner's manual

Worx WG712 Owner's manual

in other languages

Related papers

Other documents