Sanus VMF408 User manual

Customer Service

Americas: 800-359-5520 • 952-225-6013 • info@sanus.com

UK: 0800 056 2853 • [email protected]

Europe, Middle East, and Africa: +31 (0) 495 580 852 • europe[email protected]om

Asia Paci c: 86 755 8996 9226 • sanus.ap@milestone.com

SANUS • 6436 City West Parkway • Eden Prairie, MN 55344 USA

All other brand names or marks are used for identi cation purposes and are trademarks of their respective owners.

We are here

to help!

Please contact

Customer

Service with

any questions.

VMF408

Instruction Manual

Installation

video available at

Sanus.com

sanus.com

2

Before You Begin

WARNING: This product contains a magnet. If an implanted medical device such as a pacemaker or implantable cardioverter

de brillator (ICD) is in use, magnetic  elds may a ect the operation of those devices, resulting in serious injury or death. If you have an

implanted medical device, keep at least 13 cm (5 in.) between your device and the magnet. Please consult with your physician or medical

professional prior to using this product.

CAUTION: Avoid potential personal injuries and property damage!

 Refer to the documentation that came with your TV for additional considerations

 Do not use this product for any purpose not explicitly speci ed by manufacturer

 The wall must be capable of supporting  ve times the weight of the monitor and mount combined

 This product includes directions and hardware for use with wood stud, solid concrete and concrete block walls

 If you do not understand these instructions, or have doubts about the safety of the installation, assembly or use of this product, contact

Customer Service or call a quali ed contractor

 Manufacturer is not responsible for damage or injury caused by incorrect assembly or use

Required Tools

13mm

(1/2 in.)

5.5mm

(7/32 in.)

10mm

(3/8 in.)

Specifications

 Weight capacity-DO NOT EXCEED: 27.22 kg (60 lb) includes TV and any accessories

 Swivel: ±35°

 Tilt: +0° to –10°

 Level: ±1.5°

IMPORTANT SAFETY INSTRUCTIONS – SAVE THESE INSTRUCTIONS – PLEASE READ ENTIRE MANUAL PRIOR TO USE

3

Technical Specifications

15.75

400.0

11.81

300.0

7.87

200.0

15.75

400.0

11.81

300.0

7.87

200.0

12.30

312.4

13.50

342.9

17.00

431.8

25.20

640.1

5.01

127.4

in.

[mm]

4

1.11

[28.3]

in.

[mm]

8.27

[210.1]

10°10°

35°

35

5

Supplied Parts and Hardware

WARNING: This product contains small items that could be a choking hazard if swallowed.

Before starting assembly, verify all parts are included and undamaged. If any parts are missing or damaged, do not return the damaged item to

your dealer; contact Customer Service. Never use damaged parts!

NOTE: M4, M5, M6, or M8 describes the diameter, mm describes the length of screws that are labeled M# X ##mm. Not all hardware included will

be used.

[01] x 1

[02] x 1

[03] x 1

[04] x 1

[05] x 2

M4 x 12mm

[06] x 4

M5 x 12mm

[09] x 4

M4 x 30mm

[07] x 4

M4 x 40mm

[08] x 4

M5 x 30mm

[10] x 4

Page is loading ...

7

1 Select TV Hardware

Hand thread screws into the threaded inserts on the back of your TV to determine the correct screw diameter (M4, M5, M6, or M8). Try using a

screw alone first. If you need more space, try a screw with a spacer.

CAUTION: Avoid potential personal injuries and property damage! Using hardware that is too long may damage your TV. If you

encounter resistance, stop immediately and contact customer service.

OR

8

1-1 Attach bracket to TV

[02]

For TVs with a  at back. Ensure that the bracket is level on the back of the TV. Standard con gurations are shown. If you need extra space to

accommodate cables, recesses, or protrusions, see an installation option (1-2 or 1-3) that uses spacers. For special applications, or if you are

uncertain about your hardware selection, contact Customer Service.

[06, 09,

12, 15]

[20, 21]

[02]

9

[07, 10,

13, 16]

[20, 21]

[22]

[18]

[02]

For TVs with an irregular/obstructed back. Ensure that the bracket is level on the back of the TV. Standard con gurations are shown. For special

applications, or if you are uncertain about your hardware selection, contact Customer Service.

1-2 Attach bracket to TV

[22]

[18]

10

For TVs with an irregular/obstructed back. Ensure that the bracket is level on the back of the TV. Standard con gurations are shown. For special

applications, or if you are uncertain about your hardware selection, contact Customer Service.

1-3 Attach bracket to TV

[19]

[08, 11,

14, 17]

[02]

[22]

[19]

[20, 21]

[22]

11

Slide the arms of the wall plate [03] together and insert the slide lock [26] into place. This will lock the arms into full extension making the wall

plate mounting and TV attachment easier.

Install the locking screws [25] into the sides of the face plate using the M3 hex key [32]. Screw in only until the end of the screw is  ush with the

inside of the plate. This will allow the TV to be mounted without interference.

[26]

[03]

[25]

[32]

[26]

2 Prepare the Wall Plate for Mounting

12

3-1 Locate studs and mark the wall

3 Mount the Wall Plate (Wood stud)

Verify the center of the stud(s) using an awl, a thin nail, or an edge to edge stud finder.

CAUTION: Avoid potential personal injuries and property damage!

 Drywall covering the wall must not exceed 16 mm (5/8 in.)

 Minimum wood stud size: common 51 x 102 mm (2 x 4 in.) nominal 38 x 89 mm (1¹/ x 3¹/ in.)

 Minimum horizontal space between lag bolts: 41 cm (16 in.).

For assistance in determining wall plate location, see Height Finder at sanus.com.

Level the wall plate template, [01] and mark the hole locations.

3-2 Drill pilot holes and tighten lag bolts

CAUTION:

Avoid potential injuries or property damage! Pilot holes MUST be drilled to a depth of 75 mm (3 in.), using a 5.5 mm (7/32 in.)

diameter drill bit.

CAUTION:

Improper use could reduce the holding power of the lag bolt. To avoid potential injuries or property damage:

 DO NOT over-tighten the lag bolts [29].

 Tighten the lag bolts [29] only until the washers [28] are pulled firmly against the wall plate [03].

13

[01]

41 cm

(16 in.)

≤ 16 mm

(5/8 in.)

3-1 Locate studs and mark the wall

3-2 Drill pilot holes and tighten lag bolts

[03]

75 mm

(3 in.)

[29]

[28]

13 mm

(1/2 in.)

5.5 mm

(7/32 in.)

14

3 Mount the Wall Plate (Solid concrete or concrete block)

For assistance in determining wall plate location, see Height Finder at sanus.com.

Level the wall plate template [01] and mark the hole locations.

CAUTION:

Avoid potential injuries or property damage!

 Mount the wall plate [03] directly onto the concrete surface

 Minimum solid concrete thickness: 203mm (8 in.)

 Minimum concrete block size: 203 x 203 x 406 mm (8 x 8 x 16 in.)

 Minimum horizontal space between lag bolts: 41 cm (16 in.).

CAUTION:

Avoid potential injuries or property damage!

 Pilot holes MUST be drilled to a depth of 75 mm (3 in.) using a 10 mm (3/8 in.) diameter drill bit

 Never drill into the mortar between blocks

Insert lag bolt anchors [27]. Then insert lag bolts [29] through the washers [28], the wall plate [03], and into the anchors.

CAUTION:

Improper use could reduce the holding power of the lag bolt. To avoid potential injuries or property damage:

 Be sure the anchors [27] are seated flush with the concrete surface

 Tighten the lag bolts [29] only until the washers [28] are pulled firmly against the wall plate [03]

 DO NOT over-tighten the lag bolts [29]

3-1 Mark the wall and drill pilot holes

3-2 Insert anchors and lag bolts

15

3-1 Mark the wall and drill pilot holes

[01]

75 mm

(3 in.)

[27]

[03]

[29]

[28]

3-2 Insert anchors and lag bolts

13 mm

(1/2 in.)

10 mm

(3/8 in.)

41 cm

(16 in.)

16

1. Mount the upper cover [05] using the ⁄ in. hex key [30] and four screws [24].

2. Mount the lower cover [05] using the ⁄ in. hex key [30] and four screws [24] while (optional)  tting the rear mount of the cable managment

assembly [04] between the cover [05] and the lower horizontal of the wall plate [03].

NOTE: Do not install the rear mount of the cable management assembly [04] unless you intend to install the front mount of the cable

management assembly [04] in Step 6.

[05]

[24]

[30]

[05]

4 Install Wall Plate Covers and Cable Management (Optional)

17

HEAVY! You will need assistance with this step.

1. Hang the TV with mounting bracket [02] onto the face of the wall plate [03]. The lower mounting knobs of the mounting bracket [02] will

 t into the keyhole slots of the face of the wall plate [03] while the upper knobs will drop into the top slots of the face of the wall plate [03].

2. Secure the TV to the face of the wall plate [03] by tightening the locking screws [25] with the 3mm hex key [32] until they capture the upper

knobs of the bracket [03].

[32]

[25]

[02]

[03]

5 Attach TV to Wall Plate

18

Fit the front mount of the cable managment assembly [04] onto the back of the TV bracket [02] using the ⁄ in. hex key [30] to install three screws

[23].

NOTE: Do not install the front mount of the cable management assembly [04] unless you have installed the rear mount of the cable

management assembly [04] in Step 4.

[23]

[04]

[30]

[02]

6 Complete Cable Management Installation (Optional)

19

Plug the required cables into the TV.

1. Slide the three covers of the cable managment assem-

bly [04] o the front (face plate mount), rear (wall plate

mount), and center ( oating).

2. Route the cables through the three sections.

3. Replace the covers.

1

2

3

6-1 Manage Cables (Optional)

[04]

20

Adjust up / down tilt tension by hand or using the M3 hex key [32]. Adjust level with the 5/32 hex key [31].

[32]

7 Adjust Tilt Tensions

[31]

21

After setup is complete:

A. Remove slide lock [26] from the locking position

B. Fit the slide lock [26] into the grooves of one of the slides for storage

A

B

[26]

[01]

[26]

8 Store the Slide Lock

Optional-Remove Your TV

To remove your TV from the mount, see step 5.

Page is loading ...

Sanus VMF408 User manual

Sanus VMF408 User manual

in other languages

Related papers

Other documents