Craftsman 580752271 Owner's manual

Brand: Craftsman

Model: 580752271

Category: High-pressure cleaners

Type: Owner's manual

This manual is also suitable for

Operator'sManual

3000 PSI MAX

2.7 GPIViMAX

PRESSUREWASHER

ModelNo. 580.752271

HOURS: IVlon.- Fri. 8 a.m. to5 p.m. (CT)

WARNING

Beforeusing this product, readthis

manualand follow all Safety Rules

and OperatingInstructions.

ADVERTENCIA

Antes deutilizar el producto, lea este

manualy siga todas las Reglasde

Seguridad e Instrucciones de Uso.

• Safety

• Assembly

• Operation

• Maintenance

• Parts

• Espafiol,p. 36

This pressure washer is rated in accordance to the Pressure Washer Manufacturers Association

(PWMA) standard PW101 (Testing and Rating Performance of Pressure Washers).

Esta iimpiadora a presi6n est_ ciasificada conforme a la norma PW101 (comprobaci6n y ciasificaci6n de rendimiento de limpiadoras

a presi6n) de la Asociaci6n defabricantes de bombas a presi6n (Pressure Washer Manufacturers Association, PWMA).

Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.

Visit ourCraftsmanwebsite: www.craftsman.com

Part No. 208818GS Draft A (03/04/2009)

WARRANTY.......................................... 2

REPAIRPROTECTIONAGREEMENT........................ 2

SAFETYRULES...................................... 3-5

FEATURESANDCONTROLS.............................. 6

ASSEMBLY........................................ 7-10

OPERATION....................................... 11-15

SPECIFICATIONS..................................... 16

MAINTENANCE.................................... 17-20

STORAGE........................................... 21

TROUBLESHOOTING.................................. 22

REPLACEMENTPARTS.............................. 23-33

EMISSIONCONTROLWARRANTY..................... 34-35

ESPAKIOL......................................... 36-59

HOWTO ORDERPARTS........................ BACKPAGE

CRAFTSMANFULLWARRANTY

If this Craftsmanproduct fails due to a defect in material or workmanship within two years from the date of purchase, return it

to anySearsstore, Sears Parts & RepairService Center,or other Craftsmanoutlet in the United Statesfor free repair (or

replacementif repair proves impossible).

This warranty appliesfor only 90 days from the dateof purchase if this product is ever usedfor commercial or rental

purposes.

Thiswarranty coversONLYdefectsin material andworkmanship.Searswill NOTpayfor:

• Expendableitems that canwear out from normal usewithin the warranty period, such as spray guns, hoses, nozzle

extensions, nozzles,filters and spark plugs.

• Repairsnecessarybecauseof accident, or failure to operateor maintain the product according to all supplied instructions.

• Preventivemaintenance,or repairs necessarydue to improper fuel mixture, contaminated or stalefuel.

This warranty givesyou specific legal rights, and you may also haveother rights which vary from stateto state.

Sears, Roebuck and Co., Hoffman Estates, IL 60179

Congratulations on making a smart purchase.

Your new Craftsman® product is designed and manufactured

for years of dependableoperation. But like all products, it

may require repair from time to time. That's when havinga

Repair ProtectionAgreement can saveyou money and

aggravation.

Here'swhat the RepairProtectionAgreement*includes:

• Expertservice by our 10,000 professional repair

specialists

• Unlimited serviceand no chargefor parts and labor on

all covered repairs

• Product replacement up to $1500 if your covered

product can't befixed

• Discountof10% from regular priceof serviceand related

installed parts not covered by the agreement;also, 10%

off regular price of preventivemaintenancecheck

• Fasthelp byphone-we call it Rapid Resolution- phone

support from a Sears representative.Think of us as a

"talking owner's manual".

Onceyou purchasethe RepairProtection Agreement,a

simple phone call is all it takes for you to schedule service.

You cancall anytimeday or night, or schedule a service

appointment online.

The Repair ProtectionAgreement is a risk-free purchase. If

you cancelfor any reasonduring the product warranty

period,we will provide a full refund. Or, a prorated refund

anytime after the product warranty period expires. Purchase

your RepairProtectionAgreement today!

Somelimitations and exclusionsapply. Forpricesand

additionalinformationin the U.S.A. call 1-800-827-6655.

* Coveragein Canadavaries onsome items. Forfull

details, call SearsCanadaat 1-800-361-6665.

SearsInstallation Service

ForSearsprofessional installation of home appliances,

garagedoor openers, water heaters,and other major home

items, in the U.S.A.or Canadacall 1-800-4-MY-HOME®.

@2009

Readthis manualcarefully and becomefamiliar

with yourpressurewasher. Knowitsapplications,

itslimitations, and anyhazardsinvolved.

Important Safety Information

Safety Symbolsand Meanings

ToxicFumes Kickback

2 %

SlipperySurface Fall

ElectricalShock

FluidInjection

Fire

Explosion Operator'sManual

MovingParts

FlyingObjects Hot Surface

,A Thesafety alertsymbol indicatesa potential personal

injury hazard.A signalword (DANGER,WARNING,or

CAUTION)is usedwith thealert symbol to designatea degree

or levelof hazardseriousness.A safety symbol may be used

to representthe type of hazard.Thesignal word NOTICEis

usedto addresspractices not relatedto personalinjury.

A, DANGERindicatesa hazardwhich, if not avoided, will

result in deathor serious injury.

A, WARNINGindicates a hazardwhich, if not avoided, could

result in deathor serious injury.

A, CAUTIONindicates a hazardwhich, if not avoided, could

result in minor or moderate injury.

NOTICEaddresspractices not relatedto personal injury.

A, WARNING Theengine exhaustfrom this product

contains chemicals known to the Stateof California to

cause cancer,birth defects,or other reproductive harm.

A, WARNING This product contains lead and lead

compounds, known to the State of Californiato cause

birth defects or other reproductive harm. Washyour

handsafter handling this product.

A, WARNING Runningengine gives off carbon

monoxide, an odorless, colorless, poison gas.

_ Breathingcarbon monoxide headache,

can cause

fatigue, dizziness,vomiting, confusion, seizures,

nausea,fainting or death.

Some chemicals or detergentsmay be harmful if inhaled

or ingested, causing severenausea,fainting, or

poisoning.

• OperatepressurewasherONLYoutdoors.

• Keepexhaustgasfromenteringa confinedareathrough

windows,doors,ventilationintakes,or otheropenings.

• DONOTstartor run engineindoorsor in anenclosedarea,

evenifwindowsanddoorsareopen.

• Usea respiratoror maskwheneverthereisa chancethat

vaporsmaybeinhaled.

• Readall instructionswith masksoyouarecertainthemaskwill

providethenecessaryprotectionagainstinhalingharmful

vapors.

_k WARNING Starter cord kickback(rapid retraction)can

result in bodily injury. Kickbackwill pull hand and

,_arm toward enginefaster thanyou can let go.

Broken bones,fractures, bruises, or sprains

could result.

• NEVERpullstarter cord without first relieving spraygun

pressure.

• When starting engine, pull cord slowly until resistanceisfelt

andthen pull rapidly to avoid kickback.

• After eachstarting attempt, where enginefails to run, always

point spray gun in safe direction, pressred button and squeeze

spray gun trigger to releasehigh pressure.

• Firmly grasp spray gun with both hands when using high

pressure sprayto avoid injury when spraygun kicks back.

A, WARNING Riskof electrocution.

"_,dh Contactwith power source can causeelectric

shock or burn.

• NEVERspraynearpowersource.

_k WARNING The high pressure stream of water that

this equipment produces can cut through skin

and its underlying tissues, leading to serious

injury and possible amputation.

Spray gun traps high water pressure, even when engine is

stopped and water is disconnected, which can cause

injury.

• DONOTallow CHILDRENto operate pressurewasher.

• NEVERrepairhigh pressure hose.Replaceit.

• NEVERrepairleakingconnections with sealantof any kind.

Replaceo-ring or seal.

• NEVERconnect high pressure hoseto nozzleextension.

• Keephigh pressure hoseconnectedto pump and spraygun

while system is pressurized.

• ALWAYS point spray gun in safedirection, pressred button

andsqueezespray gun trigger to releasehigh pressure,every

time you stop engine.

• NEVERaim spray gun at people,animals, or plants.

• DO NOTsecure spraygun in open position.

• DO NOTleavespray gun unattendedwhile machine is running.

• NEVERuseaspray gun which does not havea trigger lock or

trigger guardin placeand in working order.

• Always be certain spray gun, nozzlesand accessoriesare

correctly attached.

_k WARNING Fuel and its vapors are extremely

flammable and explosive.

Fire or explosion can cause severe burns

or death.

WHENADDING OR DRAININGFUEL

• Turn pressurewasher OFFand let it cool at least 2 minutes

before removing fuel cap. Loosencapslowly to relievepressure

in tank.

• Fill or drain fuel tank outdoors.

• DONOToverfill tank. Allow spacefor fuel expansion.

• If fuel spills, wait until it evaporatesbeforestarting engine.

• Keepfuel awayfrom sparks, open flames, pilot lights, heat,and

other ignition sources.

• DONOTlight a cigaretteor smoke.

WHENSTARTINGEQUIPMENT

• Ensurespark plug, muffler,fuel cap,and air cleanerarein place.

• DO NOTcrank enginewith spark plug removed.

WHENOPERATINGEQUIPMENT

• DONOTtip engine or equipmentat anglewhich causes fuel to

spill.

• DONOTsprayflammable liquids.

WHENTRANSPORTINGOR REPAIRINGEQUIPMENT

• Transport/repair with fuel tank EMPTYor with fuel shutoff valve

OFF.

• Disconnectspark plug wire.

WHENSTORINGFUELOR EQUIPMENTWITH FUELIN TANK

• Store awayfrom furnaces, stoves,water heaters,clothes

dryers, or other appliancesthat have pilot light or other ignition

source becausethey can ignitefuel vapors.

_k WARNING Contact with muffler area can result in

serious burns.

_ _ Exhaust heat/gases can ignite

combustibles, structures or damage

fuel tank causing a fire.

• DO NOTtouch hot parts and AVOIDhot exhaust gases.

• Allow equipmentto cool beforetouching.

• Keepat least5 feet (152 cm) of clearanceon all sides of

pressure washer including overhead.

• It is aviolation of California Public Resource Code,Section

4442, to use or operate the engine on any forest-covered,

brush-covered, or grass-covered land unless the exhaust

system is equipped with aspark arrester, as defined in Section

4442, maintained in effective working order. Other statesor

federaljurisdictions mayhave similar laws.

Contactthe original equipment manufacturer, retailer, or dealer

to obtain a spark arrester designed for the exhaust system

installed on this engine.

• Replacement parts must bethe sameand installed in the same

position asthe original parts.

_i, WARNING Use of pressure washer can create

puddles and slippery surfaces.

,_ Kickback from spray gun can cause you

to fall.

• Operatepressurewasher from a stable surface.

• Thecleaning areashould have adequateslopes and drainageto

reducethe possibility of a fall due to slippery surfaces.

• Beextremely careful if you must usethe pressurewasherfrom

a ladder,scaffolding, or any other similar location.

• Firmly grasp spray gun with both hands when using high

pressure sprayto avoid injury when spraygun kicks back.

_i, WARNING Unintentional sparking can result in fire or

_¢ electric shock.

WHENADJUSTINGOR MAKINGREPAIRSTO YOURPRESSURE

WASHER

• Disconnectthe spark plug wire from the spark plug and place

the wire where it cannot contact spark plug.

WHENTESTINGFORENGINESPARK

• Use approvedspark plug tester.

• DONOTcheckfor sparkwith spark plug removed.

_i, WARNING Starter and other rotating parts can

entangle hands, hair, clothing, or accessories.

• NEVERoperate pressurewasherwithout protective housing or

covers.

• DO NOTwear looseclothing, jewelry or anything that may be

caught in the starter or other rotating parts.

• Tie up long hair and removejewelry.

A WARNING Riskof eyeinjury.

Spray cansplash back or propel objects.

• Always wear indirect vented (chemical splash) safety goggles

markedto comply with ANSIZ87.1 when using or in vicinity of

this equipment.

• NEVERsubstitute safety glasses or dry-condition goggles for

indirect vented safetygoggles.

NOTICE High pressure spray may damagefragile items

including glass.

• DONOTpointspraygunatglasswhenusingMAX(0°) nozzle.

• NEVERaimspraygunatplants.

NOTICE Improper treatment of pressure washer can

damage it and shorten its life.

• If you have questions about intended use,ask dealer or contact

Sears.

• NEVERoperate units with broken or missing parts, or without

protective housing or covers.

• DO NOTby-pass any safetydevice on this machine.

• DONOTtamper with governed speed.

• DONOToperate pressure washer above rated pressure.

• DONOTmodify pressure washer inany way.

• Beforestarting pressure washer in cold weather,check all parts

of the equipment to besure ice has not formed there.

• NEVERmove machine by pulling on hoses. Use handle provided

on unit.

• Checkfuel system for leaksor signs of deterioration, such as

chafed or spongy hose,loose or missing clamps, or damaged

tank or cap. Correct all defects before operating pressure washer.

• This equipmentis designedto be usedwith Searsauthorized parts

ONLY.If equipmentis used with parts that DONOTcomply with

minimum specifications, userassumesall risks and liabilities.

KNOWYOURPRESSUREWASHER

Readthe Operator'sManual andsafetyrules beforeoperatingyourpressure washer.

Comparethe illustrations with your pressurewasher to familiarizeyourself with the locations of various controls and

adjustments. Savethis manualfor future reference.

(_ .....

A- SprayGun-- Controls the application of water onto cleaning

surface with trigger device. Includestrigger lock.

B- PrecisionSprayTM Nozzles-- Max,General,Jet Flush,Jet Soap

and FanSoap Nozzles:for various cleaning applications.

C- Accessory Tray -- Provides convenient storagefor accessories,

such as gun, spray tips, etc.

D - RecoilStarter-- Usedfor starting the engine manually.

E - Oil Fill/Dipstick -- Check,add and drain engine oil here.

F - EngineIdentification -- Provides model, type and code of

engine. Pleasehavethese readilyavailable if calling for

assistance.

G - Air Filter-- Protects engine byfiltering dust and debris out of

intakeair.

H - AutomaticCoolDownSystem-- Cycleswater through pump

when water reaches125°-155°F. Warm waterwill dischargefrom

pump onto ground. This system prevents internal pump damage.

J - Pump-- Develops high pressure.

K- EngineOn/Off Switch-- Push this switch to "On"before using

recoil starter. Push switch to "Off"for stopping engine.

L - HighPressureOutlet-- Connectionfor high pressurehose.

M - Water Inlet -- Connection for garden hose.

N- Warning/OperatingInstructionsTag-- Identifies hazardsand

proper procedureto start/stop pressurewasher.

P - BottleBracket-- Cleaningsolution bottle fits inwire form

bracket here. Concentratebottle not included.

R - Fuel Tank-- Fill tank with regular unleadedfuel. Always leave

room for fuel expansion.

S - Project Pro@ PerfectMW MSiphon-- Mixes concentrate with

pressure washer spray.

T - Hose Wrap and High Pressure Hose-- Hosewrap provides

easytransport and handling of the high pressure hose. Connect

oneend of hoseto water pump andthe other endto spray gun.

U - Nozzle Extensionwith QuickConnect -- Allows you to switch

betweenfive different PrecisionSprayTM nozzles.

V - Fold Down Handle -- Handle and accessory tray fold flat atop

cold enginefor space-saving storage.

Items Not Shown:

IdentificationLabel (near rear of base plate) -- Provides model

and serial number of pressure washer. Pleasehave these readily

available if callingfor assistance.

DetergentSiphoningTube/Filter-- Useto siphon pressurewasher

safedetergentsintothe low pressurestream.

Your pressure washer requires some assembly and is ready

for useonly after it has been properly servicedwith the

recommendedoil and fuel.

If you haveanyproblems with theassemblyofyour

pressurewasher, please call the pressurewasher helpline

at 1-800-222-3136.

UNPACKTHEPRESSUREWASHER

1. Removeeverythingfrom carton except pressurewasher.

2. Opencarton completely by cutting eachcorner from top

to bottom.

3. Removepressure washer from carton.

CARTONCONTENTS

Checkall contents. If anyparts are missing or damaged,call

the pressure washer helplineat 1-800-222-3136.

• Main Unit

• Handle

• AccessoryTray

• High PressureHose

• Spray Gun

• NozzleExtensionwith Quick ConnectFitting

• Oil Bottle

• HoseWrap

• DetergentSiphoning Hose/Filter

• Bottle BracketWireform (2)

• PerfectMixTM Siphoning Unit/Hose

• Parts Bag(which includes the following):

• Operator's Manual

• Owner's Registration Card

• Bag containing 5 PrecisionSprai MNozzles

• HandleFasteningHardwareKit (whichincludes):

• HandleBolts (2)

• CarriageBolt (2)

• Rope Guide(1)

• Plastic Knobsfor Handle(2)

• Plastic Knob (3)

• TreeClips (4)

Becomefamiliar with eachpiece beforeassemblingthe

pressure washer Identify all contents with the illustration on

page 6 If any parts are missing or damaged, call the

pressure washer helpline at1-800-222-3136.

ASSEMBLINGPRESSUREWASHER

Your Craftsmanpressure washer will needassembly before

operation:

1 Fill out and sendin registration card

2 Attach handle and accessorytray

3 Connectdetergent siphon hoseto pump

4 Add oil to engine crankcase

5 Add fuel to fuel tank

6 Connectpressure hoseto spray gun and pump

7 Connectwater supply to pump

8 Attach nozzleextension to spray gun

9 Select/attach quick connect PrecisionSprayTM nozzleto

nozzleextension

Attach Handle and Accessory Tray

1 Placehandle(A) onto handle supports (B) connectedto

main unit Make sure holes (6) in handlealign with holes

(6) on handlesupports

Insert handle carriagebolts (D) through holes from

inside of unit and attach a plastic knob (E) from outside

of unit Tighten by hand Byloosening both knobs to the

middle section of the attachmentbolt, the upper handle

canfold forward to store flat atop the cold engine Note:

DONOTfold the handle down while the engine is hot

Placeaccessorytray (F) over holes (6) on handle

(viewing from backof unit) Pushthe tree clips (H) into

the holes until they sit flat against the accessorytray

Insert multi-colored PrecisionSprai Mnozzlesand other

supplied accessoriesin spacesprovided in accessory

tray SeeHow to UseAccessory Tray

Attach rope guide (A) through handlewith plastic knob

(B). Tighten by hand. Route engine recoil rope through

guide.

Align hosewrap (6) to the back side of accessorytray.

Locate notch with "unlock"icon (D) on hosewrap.

Position notch at top with hosewrap in vertical position.

Clips in the back of accessorytray should slide into the

grooves on the inside surface of hosewrap. Slide hose

wrap on back of accessorytray and rotate 1/8 turn until

"locked"icon (E) is in vertical position. Hosewrap is

easily removed from the accessorytray for wrapping and

unwrapping of the high pressure hose. A clip to secure

the hoseon the reel makesit easyto wrap the hose

while it is detachedfrom the accessorytray.

StandardSiphonTube

Cleartube with filter:

When using the clear siphon tube, dilute

1 part PerfectMixTM ExtremeConcentrate

to 16 parts water (4 oz of concentrate

makes1/2 gallon of mix.)

Attach Project Pro® PerfectMix TM Siphon to

Pump

Attach the hose end of the blue PerfectMixTM Siphon (J) to

the barbed hosefitting (K) on the pump.

Attach PerfectMix TM Detergent Siphon to

Concentrate Bottle

PlacePerfectMixTM bottle (not included) in the wire-form

bracketon the handle. Removecap from bottle and insert the

PerfectMixTM Siphon (L). Screwthe siphon unit to the top of

the bottle (M). Usethe clip on the cap (L) to snapsiphon to

wire form bracketwhen siphon is not in a concentrate bottle.

Attach bottle brackets (F) to handlewith carriage bolts

(6) and blackplastic knobs (H). Tighten by hand.

2-1N-1 Soap System

The pressurewasher is equippedwith two detergent

siphoning hoses.

Project ProPerfectMixTM Siphon

Blue tube with blue bottle cap:

When usingthe blue PerfectMixTM siphon, use

the PerfectMixTM ExtremeConcentratestraight

from the bottle.

Add Engine Oil

1. Placepressurewasher on a flat, levelsurface.

2. Cleanareaaround oil fill and removeyellow oil fill

cap/dipstick.

3. Using oil funnel (optional), slowly pour contents of

provided oil bottle into oil fill opening.

NOTICE Improper treatment of pressure washer can

damage it and shorten its life.

• DONOTattemptto crank or startthe engine before it has been

properly servicedwith the recommended oil. This may result in an

enginefailure.

4. Replaceoil fill cap/dipstick and fully tighten.

Add Fuel

Fuel mustmeet theserequirements:

• Clean,fresh, unleaded gasoline.

• A minimum of 87 octane/87 AKI (91 RON).High altitude

use, see HighAltitude.

• Gasolinewith up to 10% ethanol (gasohol) or up to 15%

MTBE (methyl tertiary butyl ether) is acceptable.

NOTICE Avoid pressure washer damage.

Failureto follow Operator's Manualfor fuel

recommendations voids warranty.

• DONOTuseunapprovedgasolinesuchasE85.

• DONOTmixoil in gasoline.

• DONOTmodifyengineto runonalternatefuels.

To protect the fuel system from gum formation, mix in a fuel

stabilizerwhen adding fuel. SeeStorage.All fuel is not the

same. If you experiencestarting or performanceproblems

after using fuel, switch to a different fuel provider or change

brands. This engine is certified to operateon gasoline. The

emission control system for this engine is EM (Engine

Modifications).

_i, WARNING Fueland its vapors are extremely

flammable and explosive.

Fireor explosion can causesevere burns

or death.

WHENADDINGFUEL

• Turn pressure washerOFFand let it cool at least2 minutes

before removing fuel cap. Loosencapslowly to relievepressure

in tank.

• Fill fuel tank outdoors.

• DONOToverfill tank. Allow spacefor fuel expansion.

• If fuel spills, wait until it evaporatesbefore starting engine.

• Keepfuel awayfrom sparks, open flames, pilot lights, heat,and

other ignition sources.

• DONOTlight a cigarette or smoke.

Cleanarea around fuel fill cap, remove cap.

Slowly add regular unleadedfuel (A) to fuel tank (B). Be

careful not to overfill. To allow for fuel expansion, do not

fill abovethe bottom of thefuel tank neck.

3. Install fuel capand wait for any spilled fuel to evaporate.

CAUTION!Alcohol-blendedfuels (calledgasohol, ethanol or

methanol) canattract moisture, which leadsto separation and

formation of acids during storage.Acidic gascandamagethe

fuel system of an enginewhile in storage.

To avoid engine problems, the fuel system should be treated

with a fuel preserveror emptied beforestorage of 30 days or

longer. If adding a fuel preserver,fill the fuel tank with fresh

fuel. If only partially filled, air in the tank will promote fuel

deterioration during storage. If fuel preserver is not used,

drain the fuel tank, start the engine and let it run until the fuel

lines and carburetor are empty. Usefresh fuel next season.

See Storagefor additional information.

NEVERuse engine or carburetor cleaner products in the fuel

tank as permanent damagemay occur.

HighAltitude

At altitudes over 5,000 feet (1524 meters), a minimum

85 octane / 85 AKI (89 RON)gasolineis acceptable.To

remainemissions compliant, high altitude adjustment is

required. Operationwithout this adjustment will cause

decreasedperformance, increasedfuel consumption, and

increasedemissions. Seea qualified Searsdealerfor high

altitude adjustment information. Operationof the engine at

altitudes below 2,500 feet (762 meters) with the high altitude

kit is not recommended.

FreshStart® Fuel Cap

The FreshStart® fuel cap (C) is designedto hold a

cartridge (O)which contains fuel preserver.Adding fuel

preserver helps keepfuel fresh and carburetors cleanfor

easier starting all season long. TheFreshStart® fuel cap, if

equipped with a cartridge, automatically drips concentrated

fuel preserver into your fuel tank so you don't haveto add it

'ourself.

NOTE:FreshStart®fuel preserver cartridge is availableasan

optional accessory, retail item 7133386. It is not included

with the pressure washer. Contactthe original equipment

manufacturer, retailer, or dealerto obtain acartridge

designed for the FreshStart® fuel cap installedon this

engine.

Readand follow all instructions and warnings given in the

FreshStart® fuel preservercartridge package.

Connect Hose and Water Supply to Pump

NOTICE DONOTrun the pump without the water supply

connectedand turned on.

• Damagetoequipmentresultingfrom failuretofollowthis

instructionwillvoidwarranty.

4. Runwater through garden hosefor 30 secondsto flush

it of debris. Turn off water.

IMPORTANT:DONOTsiphon standing water for the water

supply. Use ONLYcold water (less than 100°F).

5. Connectgarden hose(not to exceed50 feet in length) to

water inlet. Tighten by hand.

NOTE:Removeand discard the shipping caps from the

pump's high pressure outlet and water inlet before attaching

hoses.

1. Uncoil high pressure hose andattachone end of hoseto

baseof spray gun. Tighten by hand.

_i, WARNING The high pressure stream of water that

this equipment produces can cut through skin

and its underlying tissues, leading to serious

injury and possible amputation.

• NEVERconnect high pressure hoseto nozzleextension.

• Keephigh pressure hoseconnectedto pump and spraygun

while system is pressurized.

• Always becertain spray gun, nozzlesandaccessoriesare

correctly attached.

2. Attach other end of high pressure hoseto high pressure

outlet on pump. Tighten by hand.

Beforeconnectinggarden hoseto water inlet, inspect

inlet screen (A). Cleanscreen if it contains debris or have

it replacedif damaged.DONOTrunpressure washerif

inlet screenisdamagedor missing.

NOTICE Using aOneWay Valve (vacuumbreakeror check

valve) at pump inlet can cause pump or inlet connector

damage.

• ThereMUSTbeatleasttenfeetofunrestrictedgardenhose

betweenthepressurewasherinletandanydevice,suchasa

vacuumbreakeror checkvalve.

• Damageto equipment resulting from failure to follow this

instruction will void warranty.

_i, WARNING Riskof eyeinjury.

Spray cansplash back or propel objects.

• Always wear indirect vented (chemical splash) safety goggles

markedto comply with ANSIZ87.1 when using or in vicinity of

this equipment.

• NEVERsubstitute safety glasses or dry-condition goggles for

indirect vented safetygoggles.

6. Turn ONthe water, press red button (B) on the gun and

squeezethe trigger to purge the pump system of air and

impurities.

Checklist Before Starting Engine

Reviewthe unit to ensureyou haveperformed all of the

following:

1. Besure to read SafetyRules and Operationsections

before using the pressure washer.

2. Makesure handleis in placeand secure.

3. Checkthat oil has beenadded to proper levelin engine

crankcase.

4. Add proper fuel to fuel tank.

5. Checkfor proper hoseconnections (high pressureand

water supply) and that there are no kinks, cuts, or

damageto the high pressure hose.

6. Provide proper water supply (not to exceed100°F).

HOWTOUSEYOURPRESSUREWASHER

If you haveanyproblems operating your pressure washer,

pleasecallthe pressure washer helpline at 1-800-222-3136.

Pressure Washer Location

PressureWasherClearance

_i, WARNING Exhaustheat/gases can ignite

combustibles, structures or damagefuel tank

causing a fire.

• Keepat least5 ft. (152 cm) clearanceon all sides of pressure

washer including overhead.

Placepressure washer outdoors in an area that will not

accumulate deadlyexhaustgas. DONOTplacepressure

washer where exhaustgas (A) could accumulate and enter

inside or be drawn into a potentially occupied building.

Ensureexhaustgas is kept awayfrom anywindows, doors,

ventilation intakes, or other openingsthat can allow exhaust

gasto collect in aconfined area. Prevailingwinds and air

currents should be taken into considerationwhen positioning

_ressurewasher.

_i, WARNING Runningenginegives off carbon

monoxide,an odorless, colorless, poisonous gas.

_ Breathing cancause headache,

carbon monoxide

fatigue, dizziness,vomiting, confusion, seizures,

nausea,fainting or death.

• OperatepressurewasherONLYoutdoors.

• Keepexhaustgasfromenteringa confinedareathrough

windows,doors,ventilationintakes,or otheropenings.

• DONOTstartor runengineindoorsor in anenclosedarea,

evenifwindowsanddoorsareopen.

To Start Your Pressure Washer

To start your engine-powered pressurewasher for the first

time, follow these instructions step-by-step. This information

alsoapplies wheneveryou start the engine after you havelet

the pressure washer sit idle for at leasta day.

1. Placepressurewasher outside nearan water source

capableof supplying water at aflow rate greaterthan

3.7 gallons per minute and no less than 20 PSI at

pressurewasher end of garden hose.

2. Checkthat high pressure hose is tightly connectedto

spray gun and pump. SeeAssemblyfor illustrations.

3. Makesure unit is in a levelposition.

4. Connectgarden hoseto water inlet on pressurewasher

pump.

NOTICE DONOTrun the pump without the water supply

connectedand turned on.

• Damageto equipmentresultingfromfailureto followthis

instructionwill voidwarranty.

5. Turn ONthe water, press red button on the gun and

squeezethe trigger to purge the pump system of air and

impurities.

6. Attach nozzleextension to spray gun. Tighten by hand.

ChoosePrecisionSprayTM nozzleyou want to use, pull

backon collar of nozzleextension, insert nozzleand

releasecollar. Tug on nozzleto makesure it is securelyin

place.SeeHow to Use PrecisionSprayTM NozzleSystem.

8. Pushengine On/Offswitch (B) to "On" position.

IMPORTANT:Beforestarting the pressure washer, be sure

'ou arewearing safety goggles as described below.

_k WARNING Riskof eyeinjury.

Spraycan splash backor propel objects.

• Always wear indirect vented (chemicalsplash) safety goggles

markedto comply with ANSIZ87.1 when using or in vicinity of

this equipment.

• NEVERsubstitute safety glasses or dry-condition goggles for

indirect vented safetygoggles.

NOTE:This unit is equipped with a ReadyStart® engine.A

ReadyStart® enginemeans there is no priming or choking

required.

9. Whenstarting engine, position yourself as

recommendedand grasp starter grip handle and pull

slowly until you feel some resistance.Then pull rapidly

to start engine.

_i, WARNING Starter cord kickback (rapid retraction) can

result in bodily injury. Kickback will pull hand and

_. arm toward engine faster than you can let go.

Broken bones, fractures, bruises, or sprains

could result.

• NEVERpullstarter cord without first relieving spraygun

pressure.

• When starting engine, pull cord slowly until resistanceisfelt

andthen pull rapidly to avoid kickback.

• After eachstarting attempt, where enginefails to run, always

point spray gun in safe direction, pressred button and squeeze

spray gun trigger to releasehigh pressure.

• Firmly grasp spray gun with both hands when using high

pressure sprayto avoid injury when spraygun kicks back.

O. Return recoil starter slowly. DONOT let rope "snap

back" against starter.

11. Point spray gun in a safedirection, push the red button

to releasethe trigger lock, and pull the trigger.

_i, WARNING The high pressure stream of water that

this equipment produces can cut through skin

and its underlying tissues, leading to serious

injury and possible amputation.

Spray gun traps high water pressure, even when engine is

stopped and water is disconnected, which can cause

injury.

• DONOTallow CHILDRENto operatepressure washer.

• Keephigh pressure hoseconnectedto pump and spraygun

while system is pressurized.

• NEVERaim spraygun at people,animals, or plants.

• DO NOTsecure spray gun in open position.

• DO NOTleavespray gun unattendedwhile machine is running.

• NEVERuse aspray gun which doesnot have atrigger lock or

trigger guard in place andin working order.

• Always be certain spray gun, nozzlesandaccessoriesare

correctly attached.

_i, WARNING Contact with muffler area can result in

serious burns.

Exhaust heat/gases can ignite

combustibles, structures or damage

fuel tank causing a fire.

• DO NOTtouch hot parts and AVOIDhot exhaust gases.

• Allow equipmentto cool beforetouching.

• Keepat least5 feet (152 cm) of clearanceon all sides of

pressure washer including overhead.

• It isa violation of California Public ResourceCode,Section

4442, to use or operate the engine on any forest-covered,

brush-covered, or grass-covered land unlessthe exhaust

system is equippedwith a spark arrester,as defined in Section

4442, maintained ineffective working order. Otherstates or

federaljurisdictions may havesimilar laws.

Contactthe original equipment manufacturer, retailer, or dealer

to obtain a sparkarrester designedfor the exhaustsystem

installed onthis engine.

• Replacementparts must bethe same andinstalled in the same

position as the original parts.

Howto Stop Your Pressure Washer

1. Release spray gun trigger and let engine idle for two

minutes.

PushengineOn/Offswitch to "Off" position.

ALWAYSpoint spray gun in a safe direction, push red

button and squeezespray gun trigger to releaseretained

high water pressure.

_i, WARNING The high pressure stream of water that

this equipment produces can cut through skin

and its underlying tissues, leading to serious

injury and possible amputation.

Spray gun traps high water pressure,evenwhen engine is

stopped and water is disconnected, which can cause

injury.

• Keephighpressurehoseconnectedto pumpandspraygun

whilesystemispressurized.

• ALWAYSpointspraygunin safedirection,pressredbutton

andsqueezesprayguntriggerto releasehighpressure,every

timeyoustopengine.

IMPORTANT:Spray gun traps high water pressure,even

when engine is stopped and water is disconnected.

How to Use Accessory Tray

The unit is equipped with an accessorytray with places to

store your spray gun, nozzleextension and quick connect

spray tips. Thereis also a detachable hosewrap at the back

of the accessorytray to hold your high pressure hose.

1. Placenozzleextension in clip on back of accessorytray.

f .............

2. Placespray gun through hole on accessorytray on right

side of unit.

3. Insert multi-colored PrecisionSprayTM nozzlesin spaces

provided in accessorytray.

4. Wrap high pressure hoseon hosewrap then attach hose

wrap to back of accessorytray.

5. Hook providedon back of accessorytray for safely

storing safety goggles.

How to Use PrecisionSprayTM Nozzle System

The quick-connect on the nozzleextension allows you to

switch betweenfive different PrecisionSprayTM system

nozzles. PrecisionSprai Mnozzlescan be changedwhile

pressure washer is running oncespray gun trigger lock is

engaged.

Followtheseinstructionsto changePrecisionSprayTM

nozzles:

1. Pull back collar on quick-connect and pull current

PrecisionSprayTM nozzleoff. Store PrecisionSprayTM

nozzlesin holder provided on the accessorytray.

_k WARNING The high pressure stream of water that

this equipment produces cancut through skin

and its underlying tissues, leadingto serious

injury and possible amputation.

• NEVERexchangePrecisionSprayTM nozzleswithoutthetrigger

lockbeingengagedonthespraygun.

• DONOTtwist PrecisionSprayTM nozzleswhilespraying.

Select desired PrecisionSprayTM nozzle:

• Select orange general PrecisionSprayTM nozzlefor all

purpose cleaning. Cleansvinyl siding, brick patios,

concrete driveways and other surfaces.

GENERAL

Selectred max PrecisionSprayTM nozzlefor maximum

cleaning.Greatfor cleaningstubborn stains,including

grease,tar, wax,and otherhard to removestains.

O MAX

Select cyanjet flush PrecisionSprai Mnozzlefor

quick high flow clean up and long reachcleaningof

second story siding and windows.

JET FLUSH

Select magentajet soap PrecisionSprayTM nozzleto

launch soapto second story siding and windows.

JET SOAP

SelectblackfansoapPrecisionSprayTM nozzlefor

general cleaning. Greatfor applying soap to

vehicles, boats, driveways,decks, and patios.

FAN SOAP

3. Pull backon collar,insert newPrecisionSprayTM nozzle

and releasecollar.Tug on nozzleto makesureit issecurely

in place.

UsageTips

• For most effective cleaning, keep PrecisionSprayTM nozzle

from 8 to 24 inches (20 to 61 cm) awayfrom cleaning

surface.

• If you get PrecisionSprayTM nozzletoo close, especially

using a high pressure nozzle,you may damagesurface

being cleaned.

• DONOTget closer than 6 inches (15 cm) when cleaning

tires.

2-1N-1 Soap System

_i, CAUTION Chemicalscancause bodily injury, and/or

property damage.

• NEVERusecausticliquidwith pressurewasher.

• UseONLYpressurewashersafedetergents/soaps.Followall

manufacturersinstructions.

CleaningandApplyingDetergentwith the

Project Pro® PerfectMixTM Siphon

To apply undiluted detergent using the blue

PerfectMixTM siphon, follow these steps:

1. Reviewuse of PrecisionSprayTM

nozzles.

2. Attach PerfectMixTM siphon hoseto

pump and PerfectMixTM concentrate

bottle.

NOTICE Contactwith the hot muffler candamagedetergent

siphoning tube.

• When inserting the siphon intoa detergent solution bottle, route

thetubesoasto keepit from inadvertently contacting thehot

muffler.

3. Make sure fan soap (black) or jet soap nozzle(magenta)

is installed.

NOTE:Detergentcannot be applied with the high pressure

nozzles(Cyan,Orangeor Red).

4. Make sure garden hose is connectedto water inlet.

Checkthat high pressure hoseis connected to spray gun

and pump. Turn on water.

NOTICE You must attachall hoses beforeyou start the

engine.

• Startingtheenginewithoutall thehosesconnectedandwithout

thewaterturnedONwilldamagethe pump.

• Damageto equipmentresultingfrom failureto followthis

instructionwillvoidwarranty.

5. Start engine following instructions How to Start Your

Pressure Washer.

6. Apply detergentto a dry surface, starting at lower

portion of areato be washed and work upward, using

long, even, overlappingstrokes.

7. Allow detergent to "soakin"for 3-5 minutes before

washing and rinsing. Reapplyas neededto prevent

surfacefrom drying. DONOTallow detergent to dry on

(prevents streaking).

Cleaningand ApplyingDetergentwith the StandardClear

Siphon

To apply diluted detergent using the

standard clearsiphon tube, follow these

steps:

1. Reviewuseof PrecisionSprayTM

nozzles.

2. Attach clear siphon hoseto barbedfitting on pump.

3. Mix detergent solution as required by job.

4. Placesmall filter end of clear siphoning tube into

container with diluted solution as described above.

NOTE:DONOT insert standard siphon hose in Extreme

Concentrate.Failureto dilute concentratewill causeexcessive

application and consumption of solution.

NOTE:Makesure the filter is fully submerged in fluid while

applying solution.

NOTICE Contactwith the hot muffler can damagedetergent

siphoning tube.

• Wheninsertingthesiphonintoadetergentsolutionbottle,route

thetubesoasto keepitfrom inadvertentlycontactingthehot

muffler.

5. Makesure fan soap (black) or jet soap nozzle(magenta)

is installed.

NOTE:Detergentcannot be applied with the high pressure

nozzles(Cyan,Orangeor Red).

6. Makesure garden hoseis connectedto water inlet.

Checkthat high pressure hose is connectedto spray gun

and pump. Turn on water.

NOTICE You must attachall hoses beforeyou start the

engine.

• Startingtheenginewithoutall thehosesconnectedandwithout

thewaterturnedONwilldamagethe pump.

• Damageto equipmentresultingfrom failureto followthis

instructionwillvoidwarranty.

Start enginefollowing instructions How to Start Your

Pressure Washer.

Apply detergent to a dry surface, starting at lower

portion of areato be washedand work upward, using

long, even,overlapping strokes.

9. Allow detergent to "soak in" for 3-5 minutes before

washing and rinsing. Reapplyas neededto prevent

surfacefrom drying. DONOTallow detergentto dry on

(prevents streaking).

IMPORTANT:You must flush the detergent siphoning system

after each use by placingthe filter into a bucket of clean

water, then run the pressure washer in low pressure for 1-2

minutes.

Pressure Washer Rinsing

ForRinsing:

1. Removesoap PrecisionSprayTM nozzlefrom nozzle

extension.

2. Selectand install desiredhigh pressure nozzlefollowing

instructions How to UsePrecisionSpraSMNozzleSystem.

3. Keepspray gun a safedistance from areayou plan to

spray.

A. WARNING Kickbackfrom spray gun cancauseyou to

fall.

• Operatepressurewasherfrom astablesurface.

• Beextremelycarefulif youmustusethepressurewasherfrom

a ladder,scaffolding,or anyothersimilarlocation.

• Firmlygraspspraygunwith bothhandswhenusinghigh

pressuresprayto avoidinjurywhenspraygunkicksback.

4. Apply a high pressure spray to a small area andthen

checksurface for damage. If no damageis found, you

can assumeit is okay to continue rinsing.

5. Start attop of areato be rinsed, working down with

same overlapping strokes asyou used for cleaning.

Cleaning Detergent Siphoning Tube

If you usedthe cleardetergent siphoning tube, you must

flush it with cleanwater beforestopping the engine.

1. Placedetergent siphoning tube/filter in a bucketfull of

cleanwater.

Removehigh pressure nozzlefrom nozzleextension.

Select and install a soap nozzlefollowing instructions

How to Use PrecisionSprayTM NozzleSystem.

Flushfor 1-2 minutes.

Shut off engine following instructions How to Stop

Pressure Washerand turn off water supply.

6. ALWAYSpoint spray gun in a safe direction push red

button and squeezespray gun trigger to releaseretained

high water pressure.

IMPORTANT:Spray gun traps high water pressure,even

when engine is stopped and water is disconnected.

A, WARNING The high pressure stream of water that

this equipment produces can cut through skin

and its underlying tissues, leading to serious

injury and possible amputation.

Spray gun traps high water pressure,evenwhen engine is

stopped and water is disconnected, which can cause

injury.

• Keephighpressurehoseconnectedto pumpandspraygun

whilesystemispressurized.

• ALWAYSpointspraygunin safedirection,pressredbutton

andsqueezesprayguntriggerto releasehighpressure,every

timeyoustopengine.

Automatic Cool Down System (Thermal Relief)

Ifyou run the engine on your pressure washer for

3-5 minutes without pressing the trigger on the spray gun,

circulating water in the pump can reachtemperatures above

125°F.The systemengagesto cool the pump by discharging

the warmwater ontothe ground.

ENGINETECHNICALINFORMATION

This is a single cylinder, overheadvalve (OHV), air cooled

engine. It is a low emissions engine.

In the State of California, Model 120000 enginesare certified

by the California Air Resources Boardto meet emissions

standardsfor 125 hours. Such certification does not grant

the purchaser, owner or operator of this engine any

additional warranties with respectto the performanceor

operational life of this engine.Theengine is warranted solely

according to the product and emissions warranties stated

elsewherein this manual.

Power Ratings

Thegross power rating for individual gas engine models is

labeled in accordancewith SAE(Society of Automotive

Engineers)codeJ1940 (Small Engine Power & Torque

Rating Procedure), and rating performance has been

obtained and corrected in accordancewith SAEJ1995

(Revision 2002-05). Torquevalues are derived at 3060 RPM;

horsepower values are derived at 3600 RPIVI.Actual gross

engine power will be lower and is affectedby, among other

things, ambient operating conditions and engine-to-engine

variability. Givenboth the wide arrayof products on which

enginesare placed andthe variety of environmental issues

applicableto operatingthe equipment,the gas engine will not

developthe ratedgross power when used in a given pieceof

power equipment (actual "on-site"or net power). This

difference is due to a variety of factors including, but not

limited to, accessories(air cleaner, exhaust, charging,

cooling, carburetor, fuel pump, etc.), application limitations,

ambient operating conditions (temperature, humidity,

altitude), and engine-to-enginevariability. Dueto

manufacturing and capacity limitations, Briggs & Stratton

may substitute an engine of higher ratedpower for this

Seriesengine.

This pressurewasher is rated in accordanceto the Pressure

Washer ManufacturersAssociation (PWIVIA)standard PW101

(Testing and Rating Performanceof PressureWashers).

PRODUCTSPECIFICATIONS

Pressure Washer Specifications

Max Outlet Pressure ....................... 3,000 PSI

Max Flow Rate............................. 2.7 GPM

DetergentMix ........................ Use asdirected

Water SupplyTemperature .......... Not to exceed100°F

Engine Specifications

Bore ................................. 2.69 in. (68mm)

Stroke ............................... 2.04 in. (52mm)

Displacement ........................ 11.58in. (190cc)

SparkPlug

Type:...................... Briggs & Stratton 692051

SetGapTo: ...................... 0.020inch (0.50mm)

ArmatureAir Gap:........... 0.010-0.014in.(0.25-0.36mm)

Valveclearancewith valvesprings installedand piston 1/4 in.

(6 mm) pasttop deadcenter(checkwhenengineiscold).

Intake.................... 0.004-0.008in.(0.10-0.20mm)

Exhaust .................. 0.004-0.008in.(0.10-0.20mm)

FuelCapacity............................... 1.6Quarts

0il Capacity........................ 20 Ounces(0.6 liter)

NOTE:Forpractical operation, the engine load should not

exceed85% of ratedpower. Enginepower will decrease

3-1/2% for each1,000 feet (300 meters) above sealeveland

1% for each 10° F(5.6° C) above77° F(25° C). It should

operatesatisfactorily at an angle up to 15°.

OWNER'SRESPONSIBILITIES

Follow the hourly or calendarintervals, whichever occurs

first. More frequent service is required when operating in

adverseconditions noted below.

• Changeengine oil

• Check/clean water inletscreen'

• Checkhigh pressure hose

• Checkdetergentsiphoning hose/tanks

• Checkspray gun and assembly for leaks

• Cleandebris

• Checkengineoil level

• Cleanengine air cleaner2

• Changeengine oil2

• Inspect muffler and spark arrester

• Replaceengine air cleaner_

• Replacespark plug

• Cleancooling systeW

Clean if clogged. Replace if perforated or torn.

2Service more often under dirty or dusty conditions.

General Recommendations

Regularmaintenancewill improve the performanceand

extendthe life of the pressurewasher. Seeany Searsor

other qualified service dealerfor service.

Thepressure washer warranty does not cover items that

havebeensubjected to operator abuseor negligence.To

receivefull valuefrom the warranty, the operator must

maintain pressurewasher as instructed in this manual

including proper storage asdetailed in Storage.

Someadjustments will needto be made periodically to

properly maintain your pressurewasher.

All service and adjustments should be madeat least once

eachseason.Follow the requirementsin the Maintenance

Schedulechart above.

NOTE:Oncea yearyou should cleanor replacethe spark

plug and replacethe air filter. A new spark plug and clean air

filter assure proper fuel-air mixture and helpyour engine run

better and last longer.

Pump Oil

DONOTattempt any oil maintenanceon this pump. The

pump is pre-lubricated and sealedfrom the factory, requiring

no additional maintenancefor the life of the pump.

Emissions Control

Maintenance,replacement,or repair ofthe emissions

controldevicesand systemsmay be performedbyany non-

roadenginerepair establishmentor individual. However,

to obtain "no charge" emissions control service, the work

must be performed by a factory authorizeddealer. Seethe

Emissions Warranty.

Before Each Use

1. Checkengine oil level.

2. Cleandebris.

3. Checkwater inlet screenfor damage.

4. Checkhigh pressure hose for leaks.

5. Checkgun and nozzleextension assemblyfor leaks.

6. Purge pump of air and contaminants.

PRESSUREWASHERMAINTENANCE

Clean Debris

Daily or before use, cleanaccumulateddebris from pressure

washer. Keeplinkage, spring and controls clean. Keeparea

around and behind muffler free from any combustible debris.

Inspect cooling air slots and openings on the pressure

washer. Theseopenings must be kept clean and

unobstructed.

Pressurewasher parts should be kept cleanto reducethe

risk of overheating and ignition of accumulated debris.

• Usea damp cloth to wipe exterior surfaces clean.

NOTICE Improper treatment of pressurewasher can

damageit and shorten its life.

• DONOTinsertanyobjectsthroughcoolingslots.

• Usea soft bristle brush to loosencaked on dirt, oil, etc.

• Usea vacuum cleanerto pick up loosedirt and debris.

Check and Clean Inlet Screen

Examinegarden hoseinlet screen. Cleanif it is clogged or

replaceif it is torn.

Check High Pressure Hose

High pressure hoses candevelop leaksfrom wear, kinking,

or abuse. Inspect hose beforeeachuse. Checkfor cuts,

leaks,abrasions,bulging of cover, or damageor movement

of couplings. If anyof these conditions exist, replacehose

immediately.

_i, WARNING The high pressure stream of water that

this equipment produces can cut through skin

and its underlying tissues, leading to serious

injury and possible amputation.

• NEVERrepairhighpressurehose.Replaceit.

• ReplacementhoseratingMUSTexceedmaximumpressure

ratingof unit.

Check Gun and Nozzle Extension

Examinehoseconnectionto spraygun and makesureit is

secure.Testtrigger bypressingit and makingsureit springs

backintoplacewhenyou releaseit. Donotdepressredbutton

andtesttrigger.Youshouldnot beableto presstrigger. Replace

spraygun immediatelyif it fails anyof thesetests.

Nozzle Maintenance

A pulsing sensationfelt while squeezingthe spray gun trigger

may be causedby excessivepump pressure.Theprincipal

causeof excessivepump pressure is a nozzleclogged or

restricted with foreign materials, such asdirt, etc. To correct

the problem, immediately cleanthe nozzlefollowing these

instructions:

1. Shut off engine and turn off water supply.

2. ALWAYSpoint spray gun in a safe direction, press red

button and and squeezespray gun trigger to release

retainedhigh water pressure.

_i, WARNING The high pressure stream of water that

this equipment produces cancut through skin

and its underlying tissues, leadingto serious

injury and possible amputation.

Spraygun traps high water pressure,evenwhen engine is

stopped and water is disconnected, which can cause

injury.

• Keephighpressurehoseconnectedto pumpandspraygun

whilesystemispressurized.

• ALWAYSpointspraygunin safedirection,pressredbutton

andsqueezesprayguntriggerto releasehighpressure,every

timeyoustopengine.

Removenozzlefrom end of nozzleextension.

Use a small paper clip to free anyforeign material

clogging or restricting nozzle(A).

Removenozzleextensionfrom spray gun.

Using a garden hose,remove additional debris by back

flushing water through nozzleextension. Backflush

between 30 to 60 seconds.

7. Reinstallnozzleintonozzleextension.

8. Reconnect nozzleextensionto spray gun.

9. Make sure garden hose is connectedto water inlet.

Checkthat high pressure hoseis connected to spray gun

and pump. Turn on water.

10. Start enginefollowing instructions How to Start Your

Pressure Washer.

11. Test pressurewasher by operatingwith eachquick

connect nozzle.

O-Ring Maintenance

Purchasean O-Ring RepairKitat your localSearsor bycalling

1-800-4-MY-HOME(469-4663) or online atwww.sears.com.It

is notincludedwith thepressurewasher.This kit includes

replacemento-rings,rubberwasherandwater inletfilter. Referto

the instructionsheetprovidedin thekit to serviceyour unit's

o-rings.

_i, WARNING The high pressure stream of water that

this equipment produces can cut through skin

and its underlying tissues, leading to serious

injury and possible amputation.

• NEVERrepairleakingconnectionswithsealantofanykind.

Replaceo-ringor seal.

ENGINEMAINTENANCE

_i, WARNING Unintentional sparking can result in fire or

_¢ electric shock.

WHENADJUSTINGOR MAKINGREPAIRSTOYOUR PRESSURE

WASHER

• Disconnectthe spark plug wire from the spark plug and place

the wire where it cannot contact spark plug.

WHENTESTINGFORENGINESPARK

• Useapproved spark plug tester.

• DONOTcheckfor sparkwith spark plug removed.

Oil

OilRecommendations

We recommendthe use of Briggs & Stratton Warranty

Certifiedoils for best performance.Other high-quality

detergent oils are acceptableif classified for serviceSF,SG,

SH,SJ or higher. DONOTusespecial additives.

Outdoortemperatures determine the proper oil viscosity for

the engine.Usethe chart to selectthe best viscosity for the

outdoor temperature range expected.

104___506886 _03o__

32 .o

-4

-22

°C

\ 40

;_30

°_20

_m m 0

--_C °

-20

-30

* Below40°F(4°C)the useofSAE30will resultin hardstarting.

** Above80°F(27°C)theuseof 10W30maycauseincreasedoil

consumption.Checkoil levelmorefrequently.

NOTE:Synthetic oil meeting ILSACGF-2,API

certification mark and APIservice symbol with

"SJ/CF ENERGYCONSERVING"or higher, is an

acceptableoil at all temperatures. Useof synthetic oil

does not alter required oil changeintervals.

CheckingOil Level

1. Make sure pressure washer is on a levelsurface.

2. Removeoil dipstick and wipe dipstick with clean cloth.

Replaceand tighten dipstick. Removeand andcheck oil

level.

3. Verify oil is at FULL mark (top hole) on dipstick. Replace

and tighten dipstick.

Full

AddingEngineOil

1. Make sure pressure washer is on a levelsurface.

2. Checkoil levelas described in CheckingOilLevel

3. If needed,slowly pour oil into oil fill opening to the FULL

mark on dipstick. DONOToverfill.

4. Tip your pressure washer to drain oil from oil fill into a

suitable container making sureyou tip your unit away

from spark plug. When crankcaseis empty, return

pressurewasher to upright position.

5. Slowly pour recommendedoil (about 20 oz. (0.6 I)) into

oil fill opening. Pauseto permit oil to settle. Fillto Full

mark on dipstick.

6. Wipe dipstick cleaneachtime oil level is checked. DO

NOToverfill.

7. Replaceand tighten dipstick.

8. Wipe up any remaining oil.

9. Reconnectspark plug wire to spark plug.

Service Air Cleaner

Your engine will not run properly and may be damagedif you

run it with a dirty air cleaner. Service more often if operating

under dirty or dusty conditions. Replacementsare available

atyour local Searsservicecenter.

To service the air cleaner, follow these steps:

1. Loosenfastener (A) and remove air cleanercover (B).

NOTICE Overfilling with oil may cause the engine to not

start, or hard starting.

• DO NOToverfill.

• If overthe FULLmark on dipstick, drain oil to reduceoil levelto

FULLmark on dipstick.

4. Replaceand tighten dipstick.

ChangingEngineOil

If you are usingyour pressurewasher under extremely dirty

or dusty conditions, or in extremely hot weather, changeoil

more often.

_i, CAUTION Avoid prolonged or repeatedskin contact

with usedmotor oil.

• Usedmotoroil hasbeenshownto causeskincancerin certain

laboratoryanimals.

• Thoroughlywashexposedareaswith soapandwater.

KEEPOUTOFREACHOFCHILDREN.DON'T

POLLUTE.CONSERVERESOURCES.RETURN

USEDOILTOCOLLECTIONCENTERS.

Changeoil while engine is still warmfrom running,as

follows:

1. Drain fuel tank by running pressure washer until fuel

tank is empty.

2. Disconnect spark plug wire and keepit away from spark

plug.

3. Cleanarea around oil fill, removeoil fill cap/dipstick.

Wipe dipstick clean.

2. Removeair cleaner (C)from base(D).

3. To loosendebris, gently tap air cleaneron a flat surface.

If excessivelydirty, replacewith a newair cleaner.

4. Install the air cleanerinto the base. Makesure air

cleanerfits securelyin the base.

5. Install cover and securewith fastener. Make sure

fastener is tight.

NOTE:You can purchasenew air filter elements by calling

1-8OO-4-MY-NOME(469-4663).

Service Spark Plug

Changingthe spark plug will help your engine to start easier

and run better.

1. Cleanareaaround spark plug.

2. Removeand inspect spark plug.

3. Replacespark plug if electrodes are pitted, burned or

porcelain is cracked. Usethe recommendedreplacement

plug. See Specifications.

Checkelectrode gap with wire feeler gaugeand reset

spark plug gap to recommended gap if necessary(see

Specifications).

5. Install spark plug and tighten firmly.

NOTE:You can purchase a newspark plug by calling

1-800-4-1VlY-HOIVlE(469-4663).

Inspect Muffler and Spark Arrester

Inspectthe mufflerfor cracks,corrosion, or otherdamage.

Removethe spark arrester,if equipped,and inspectfor

damageor carbonblockage.If replacementparts are required,

makesureto useonly original equipmentreplacementparts.

_i, WARNING Contact with muffler area can result in

serious burns.

_ Exhaust heat/gases can ignite

combustibles, structures or damage

fuel tank causing a fire.

• DO NOTtouch hot parts and AVOID hot exhaust gases.

• Allow equipment to cool beforetouching.

• Keepat least5 feet (152 cm) of clearanceon all sidesof

pressure washer including overhead.

• It isa violation of California Public Resource Code,Section

4442, to use or operatethe engine on anyforest-covered,

brush-covered,or grass-covered land unless the exhaust

system is equippedwith aspark arrester,as defined in Section

4442, maintained ineffectiveworking order. Otherstates or

federal jurisdictions may havesimilar laws.

Contactthe original equipment manufacturer, retailer, or dealer

to obtain a sparkarrester designedfor the exhaustsystem

installedon this engine.

• Replacementparts must bethe sameand installed in the same

position as the original parts.

Air Cooling System

Overtime debris may accumulate in cylinder cooling fins and

cannot be observedwithout partial engine disassembly. For

this reason,we recommendyou havea qualifiedSears

servicedealer cleanthe cooling system per recommended

intervals (see MaintenanceSchedule). Equallyimportant is to

keeptop of engine freefrom debris. See CleanDebris.

Carburetor Adjustment

Thecarburetor on this engine is low emission. It is equipped

with a non-adjustable idle mixture valve.Top speedhas been

set at the factory. If adjustment is required,seean authorized

servicedealer.

_i, CAUTION Excessively high operating speeds increase

risk of injury and damage to pressure washer.

Excessively low speeds impose a heavy load.

• DO NOTtamper with governedspeed.Pressurewasher

supplies correct ratedfrequency and voltage when running at

governedspeed.

• DO NOTmodify pressure washer in any way.

AFTEREACHUSE

Water should not remain in the unit for long periods of time.

Sedimentsor minerals candeposit on pump parts and

"freeze" pump action. Follow theseprocedures after every

use:

1. Shut off engine,turn off water supply, point gun in a

safedirection, press red button and squeezetrigger to

relievetrapped pressure and let engine cool.

_i, WARNING The high pressure stream of water that

this equipment produces can cut through skin

and its underlying tissues, leading to serious

injury and possible amputation.

Spray gun traps high water pressure,evenwhen engine is

stopped and water is disconnected, which can cause

injury.

• Keephighpressurehoseconnectedto pumpandspraygun

whilesystemispressurized.

• ALWAYSpointspraygunin safedirection,pressredbutton

andsqueezesprayguntriggerto releasehighpressure,every

timeyoustopengine.

Disconnecthose from spray gun and high pressure

outlet on pump. Drainwater from hose,gun, and spray

tip extension. Usea ragto wipe off the hose.

Empty pump of all pumped liquids by pulling recoil

handleabout 6 times. This should remove most liquid in

pump.

Coilhigh pressure hoseon hosewrap provided on

accessorytray.

Store unit in a clean, dry area.

If storing for more than 30 days see Long Term Storage

on next page.

_i, WARNING Fueland its vapors are extremely

flammable and explosive.

Fireor explosion can causesevere burns

or death.

WHENSTORINGFUELOREQUIPMENTWITHFUELINTANK

• Storeawayfrom furnaces,stoves,waterheaters,clothes

dryers,or otherappliancesthathavepilotlightor other

ignitionsourcebecausetheycanignitefuelvapors.

Page is loading ...

Craftsman 580752271 Owner's manual

Brand: Craftsman

Model: 580752271

Category: High-pressure cleaners

Type: Owner's manual

This manual is also suitable for

Download PDF

report

in other languages

español: Craftsman 580752271 El manual del propietario

Craftsman 580752271 Owner's manual

This manual is also suitable for

Craftsman 580752271 Owner's manual

in other languages

Related papers

Other documents