RedMax EBZ8001 User manual

WARNING

OWNER/OPERATOR MANUAL

MODE D’EMPLOI

MANUAL DE INSTRUCCIONES

BACKPACK BLOWER

SOUFFLANTE DORSALE

SOPLADOR DE MOCHILA

848-L5M-93A1 (612)

EBZ8001

EBZ8001RH

The engine exhaust from

this product contains

chemicals known to the

State of California to cause

cancer, birth defects or

other reproductive harm.

WARNING

ADVERTENCIA

AVERTISSEMENT

ADVERTENCIA

Before using our products,

please read this manual

carefully to understand the

proper use of your unit.

APPLICABLE SERIAL NUMBERS :

EBZ8001 : 61206884 and up

EBZ8001RH : 61201408 and up

Los gases de escape del

motor de este producto

contienen sustancias

químicas conocidas por el

Estado de California como

causantes de cáncer,

malformaciones en recién

nacidos y otros problemas

de reproducción.

Les échappements du

moteur de ce produit

contiennent des produits

chimiques connus par l’Etat

de Californie comme étant

responsables de cancers,

d’anomalies congénitales et

d’autres atteintes à

l’appareil reproducteur.

Antes de usar nuestros

productos, lea

detenidamente este manual

a fin de familiarizarse con el

uso correcto de este

aparato.

Avant d’utiliser cette

ce

produit

, veuillez lire

attentivement ce manuel

afin de bien comprendre le

bon fonctionnement de cet

appareil.

NUMEROS DE SERIE APPLICABLES :

EBZ8001 : 61206884 et au-delà

EBZ8001RH : 61201408 et au-delà

NÚMEROS DE SERIE APLICABLES:

EBZ8001 : 61206884 y superior

EBZ8001RH : 61201408 y superior

2

SAFETY FIRST

Instructions contained in warnings within this manual

and warning seals marked with a symbol on the

blower concern critical points which must be taken into

consideration to prevent possible serious bodily injury,

and for this reason you are requested to read all such

instructions carefully and follow them without fail.

Note that there may be times when warning seals peel

off or become soiled and impossible to read. If this

happens, you should contact the dealer from which you

purchased the product to order new seals and affix the

new seal(s) in the required location(s).

■ NOTES ON TYPES OF WARNINGS

Instructions labeled as shown at left, concern

critical steps or procedures which must be

followed in order to prevent accidents which could

lead to serious bodily injury or death.This mark is

used to indicate instructions which must be

followed without exception.

Instructions labeled as shown at left concern steps or

procedures which, if not followed correctly, could lead

to mechanical failure, breakdown, or damage.

Used to label supplementary instructions designed to

provide hints or directions useful in the use of the

product.

NOTE

IMPORTANT

WARNING

1. Parts location………………………………………4

2. Specifications………………………………………4

3. Warning labels on the machine …………………6

4. Symbols on the machine …………………………6

5. For safe operation…………………………………8

6. Set up ……………………………………………20

7. Fuel ………………………………………………22

8. Operation …………………………………………28

9. Maintenance ……………………………………32

10. Storage……………………………………………40

11. Troubleshooting guide …………………………42

12. Parts list …………………………………………43

Contents

English

Page is loading ...

3. Warning labels on the machine

6

English

For safe operation and maintenance, symbols are

carved in relief on the machine. According to these

indications, please be careful not to make a mistake.

(a) The port to refuel the "MIX GASOLINE"

Position: FUEL TANK CAP

(b) The direction to close the choke

Position: INTAKE CUP

(c) The direction to open the choke

Position: INTAKE CUP

IMPORTANT ENGINE INFORMATION

THIS ENGINE MEETS U.S. EPA PH2 AND 2006

CALIFORNIA EMISSION REGULATIONS FOR SI

SORE’s COMPLIANCE PERIOD : CATEGORY A

ENGINE FAMILY : 6KZXS.0725PQ ; EM

ENGINE DISPLACEMENT : 72cc

REFER TO OWNER’S MANUAL FOR MAINTE-

NANCE SPECIFICATIONS AND ADJUSTMENTS.

MANUFACTURED:

U.S. PATENT NO.

MADE IN JAPAN

(1) Read owner's manual before operating this

machine.

(2) Wear head, eye and ear protection.

(3) Handling this machine improperly could result

in accidents causing serious injury or death.

Read this manual carefully and practice using

the blower until you are fully acquainted with all

operations and have learned to use it correctly.

If warning label peel off or become soiled and

impossible to read, you should contact the dealer from

which you purchased the product to order new labels

and affix them in the required location(s).

Never modify your machine.

We won't warrant the machine, if you use the

remodeled machine or you don't observe the

proper usage written in the manual.

WARNING

IMPORTANT

4. Symbols on the machine

3. Etiqueta de advertencia en la máquina

3. Etiquettes d’avertissement sur la machine

7

Français Español

INFORMATION IMPORTANTE CONCERNANT LE MOTEUR

U.S. PATENT NO.

CE MOTEUR EST CONFORME AUX REGLEMENTS SUR LES

EMISIONS DE GAZ U.S. EPA PH2 ET 2006 DE LA CALIFORNIE

POUR UNE PERIODE DE CONFORMITE SI SORE: CATEGORIE A

TYPE DE MOTEUR : 6KZXS.0725PQ ; EM

CYLINDREE DU MOTEUR : 72 cc

SE REFERER AU MANUEL DE L’UTILISATEUR POUR LES

SPECIFICATIONS D’ENTRETIEN ET LES REGLAGES.

FABRIQUE PAR :

MADE IN JAPAN

(1) Lire le mode d’emploi avant d’utiliser cette

machine.

(2) Porter un casque et des lunettes de sécurité, un

casque antibruit.

(3) Une manipulation incorrecte de cette machine

peut provoquer des accidents graves ou

mortels. Lisez attentivement ce mode d'emploi

et entraînez-vous à utiliser le souffleur jusqu'à

ce que vous maîtrisiez parfaitement toutes les

opérations et que vous ayez appris à vous en

servir correctement.

Si les étiquettes d’avertissement se décollent,

deviennent sales ou impossibles à lire, commander de

nouvelles étiquettes auprès du revendeur pour les

remplacer.

Ne pas modifier votre machine.

La garantie sera annulée si la souffleurs a été

modifiée ou utilisée de manière non conforme aux

instructions de ce mode d’emploi.

AVERTISSEMENT

IMPORTANT

Des symboles en relief ont été placés sur la machine

pour assurer la sécurité à l’usage et faciliter l’entretien.

Prendre soin d’observer les indications suivantes afin

d’éviter les erreurs.

(a) Emplacement de remplissage du “MELANGE”

Emplacement: BOUCHON DU RESERVOIR DE

CARBURANT

(b) Position fermée du starter

Emplacement: COUDE DE L'ADMISSION

(c) Position ouverte du starter

Emplacement: COUDE DE L'ADMISSION

(1) Lea el manual de propietario antes de usar esta

máquina.

(2) Use elementos de protección para la cabeza,

ojos y oídos.

(3) El uso incorrecto de esta máquina puede causar

accidentes, lo cuales a su vez pueden ocasionar

graves lesiones o la muerte. Lea este manual

detenidamente y practique con el soplador

hasta que se haya familiarizado por completo

con todas las operaciones y haya aprendido a

usarlo correctamente.

Si una etiqueta de advertencia se desprende o ensucia

y se torna ilegible, tome contacto con el distribuidor del

cual adquirió el producto y solicite nuevas etiquetas;

luego, pegue las etiquetas en los puntos necesarios.

Nunca modifique la máquina.

La garantía quedará nula si usted remodela la

máquina o si no la utiliza correctamente de

acuerdo con las instrucciones de este manual.

ADVERTENCIA

IMPORTANTE

Para un uso y mantenimiento seguro, se han

estampado símbolos en relieve en la máquina.

Observe siempre estas indicaciones y tenga cuidado

de no cometer un error.

(a) El orificio de llenado de combustible “MIX

GASOLINE”

Posición: TAPÓN DEL DEPÓSITO DE

COMBUSTIBLE

(b) La dirección en que se cierra el estrangulador

Posición: RECIPIENTE DE ADMISIÓN

(c) La dirección en que se abre el estrangulador

Posición: RECIPIENTE DE ADMISIÓN

ESTE MOTOR CUMPLE CON LAS NORMAS SOBRE

EMISIONES U.S. EPA PH2 Y 2006 DE CALIFORNIA PARA EL

PERÍODO DE CONFORMIDAD “SI SORE”: CATEGORÍA A

TIPO DE MOTOR : 6KZXS.0725PQ ; EM

CILINDRADA DEL MOTOR : 72 cc

CONSULTE EL MANUAL DEL PROPIETARIO PARA LAS

ESPECIFICACIONES Y AJUSTES DE MANTENIMIENTO.

FABRICADO POR:

INFORMACIÓN IMPORTANTE ACERCA DEL MOTOR

U.S. PATENT NO.

FABRICADO EN JAPÓN

4. Symboles utilises sur la machine 4. Símbolos presentes en la máquina

8

1. Read this Blower Owner/Operator Manual

carefully. Be sure you understand how to

operate this unit properly before you use it.

Failure to do so could result in serious injury.

2. Be sure to keep this manual handy so that you

may refer to it later whenever any questions

arise. Also note that you are requested to

contact the dealer from whom you purchased

the product for assistance the event that you

have any questions which cannot be

answered herein.

3. Always be sure to include this manual when

selling, lending, or otherwise transferring the

ownership of this product.

4. Do not lend or rent your machine without the

owner's manual.

5. Be sure that anyone using your unit

understands the infomation contained in this

manual.

6. Never let a child under 13 years old use the

machine.

■ WORKING CONDITION

1. Refrain from operating the blower if you are tired, ill,

or upset, or if you are under the influence of alcohol,

drugs or medication.

2. To reduce the risk of hearing loss associated with

sound level(s), hearing protection is required.

3. To reduce the risk of injury associated with thrown

objects, always wear eye protection and foot

protection. Eye protection should meet the

requirements of ANSI Z87.1.

4. To reduce the risk of injury associated with the

inhalation of dust, use a face filter mask in dusty

conditions.

5. Wear sturdy rubber-soled shoes or shoes with some

other form of anti-slip protection to help protect you

against falling.

6. To reduce the risk of injury associated with objects

being drawn into air intake and rotating parts, do not

wear loose clothing, scarves, neck chains,

unconfined long hair, and the like.

7. Prolonged use of a blower, exposing the operator to

vibrations and cold may produce whitefinger disease

(Raynaud’s phenomenon), which symptoms are

tingling and burning sensations followed by loss of

color and numbness in the fingers. All factors which

contribute to whitefinger disease are not known, but

cold weather, smoking diseases or physical

conditions as well as long periods of exposure to

WARNING

5. For safe operation

English

Page is loading ...

10

vibration are mentioned as factors. In order to

reduce the risk of whitefinger disease, the following

precautions are strongly recommended;

a) Keep your body warm. Never use blower during

rains.

b) Wear thick anti-vibration gloves.

c) Take more than 5 minutes of break in warm place

frequently.

d) Maintain a firm grip at all times, but do not

squeeze the handles with constant, excessive

pressures.

e) If you feel discomfort, redness and swelling of

your fingers or any other part of your body, see a

doctor before getting worse.

8. The ignition system of your unit produces an

electromagnetic field of a very low intensity. This

field may interfere with some pacemakers. To

reduce the risk of serious or fatal injury, persons with

pacemaker should consult their physician and the

pacemaker manufacturer before operating this tool.

■ WORKING CIRCUMSTANCE

1. To reduce the risk of injury associated with exhaust

fume inhalation, do not operate in unventilated area.

The exhaust gases contain harmful carbon

monoxide.

2. Avoid using the blower where stable footing and

balance are not assured.

■ AVOID NOISE PROBLEM

Check and follow the local regulations as to

sound level and hours of operations for blower.

1. Operate power equipment only at reasonable hours-

not early in the morning or late at night when people

might be disturbed. Comply with times listed in local

ordinances.

2. To reduce sound levels, limit the number of pieces of

equipment used at any one time.

3. Operate power blowers at the lowest possible

throttle speed to do the job.

IMPORTANT

5. For safe operation

English

Page is loading ...

12

4. Check your equipment before operation, especially

the muffler, air intakes and air filters.

■ WORKING PLAN

• When planning your work schedule, allow plenty of

time to rest. Limit the amount of time over which the

product is to be used continuously to somewhere

around 30 ~ 40 minutes per session, and take 10 ~

20 minutes of rest between work sessions. Also try

to keep the total amount of work performed in a

single day under 2 hours or less.

■ FUEL

To reduce the risk of fire and burn injury:

a) Handle fuel with care. It is highly flammable.

b) Do not smoke while handing fuel.

c) Do not refuel a hot engine.

d) Do not refuel a running engine.

e) Avoid spilling fuel or oil. Always wipe unit dry before

using.

f) Move at least 10 ft. (3 meters) away from the fueling

point before starting engine.

g) Always store gasoline in a container approved for

flammable liquids.

h) Make sure the unit is properly assembled and in

good operating condition.

■ BEFORE STARTING THE ENGINE

• Each time before starting the engine, inspect the

entire unit to see if every part is in good order and is

securely tightened in place. If any damage is found

in the fuel line, the exhaust line, or the ignition

wiring, do not use the blower until it has been

repaired.

Before starting operation, always make sure to

check if any obstacles are left inside the volute

case and net. The obstacles may cause damage on

fan and volute case and serious injury.

IMPORTANT

WARNING

5. For safe operation

English

Page is loading ...

14

Check to see if the shock-absorbing rubber mount has

become cracked or otherwise damaged. Note that

failing to replace this rubber mount when it has

become cracked or damaged may cause the engine

to come loose from its frame during use, thus

resulting in possible serious bodily injury.

If cracked, be sure to replace without delay.

To reduce the risk of injury associated with contacting

rotating parts, stop the engine before installing or

removing attachments. Do not operate without net in

place. Always disconnect the spark plug before

performing maintenance or accessing movable parts.

■ USING THE PRODUCT

1. Check the work area that the blower will be used in

and remove or cover all valuables that may be

damaged by the air blast or thrown debris.

2. To reduce the risk of injury associated with thrown

objects.

a) Watch out for children, pets, open windows or

freshly washed cars, and blow debris safely

away.

b) Use the full blower nozzle extension so the air

stream can work close to the ground.

c) Do not allow bystanders in work area.

d) Do not point the blower tube in the direction of

people or pets.

e) Always check to be sure that no debris has been

blown onto someone else’s property.

f) Pay attention to the direction of the wind, do not

work against the wind.

g) Never point a blower tube toward an open flame

to avoid the possibility of igniting the unit, causing

injury to yourself or damage to surroundings.

3. To minimize blowing time.

a) Use rakes and brooms to loosen debris before

blowing.

b) In dusty conditions, slightly dampen surfaces or

WARNING

5. For safe operation

English

Page is loading ...

16

use mister attachment when water is available.

c) Conserve water by using power blowers instead

of hoses for many lawn and garden applications,

including areas such as gutters, screens, patios,

grills, porches and gardens.

4. Never to touch the spark plug or plug cord while the

engine is in operation. Doing so may result in being

subjected to an electrical shock.

5. Never to touch the muffler, spark plug, other metallic

parts of the engine or engine cover while the engine

is in operation or immediately after shutting down the

engine. These metallic parts and engine cover reach

high temperatures during operation and doing so

could result in serious burns.

6. After using blowers and other equipment, CLEAN

UP! Dispose of debris in trash receptacles.

■ MAINTENANCE

1. In order to maintain your product in proper working

order, perform the maintenance and checking

operations described in the manual at regular

intervals.

2. Always be sure to turn off the engine and disconnect

the spark plug before performing any maintenance

or checking procedures.

The metallic parts and engine cover reach high

temperatures immediately after stopping the

engine.

3. Examine the blower at intervals for loose fasteners

and rusted or damaged parts. Use special care

around the fuel line, the muffler, and the ignition

wiring.

4. All engine service except for those described in this

manual should be performed by competent service

personnel. Improper service to the blower fan and

muffler could cause a hazardous failure.

5. When replacing the any other part, or any lubricant,

always be sure to use only RedMax products or

products which have been certified by RedMax for

use with the RedMax product.

6. In the event that any part must be replaced or any

WARNING

5. For safe operation

English

Page is loading ...

18

5. For safe operation

English

maintenance or repair work not described in this

manual must be performed, please contact a

representative from the store nearest RedMax

authorized servicing dealer for assistance.

7. Do not use any accessory or attachment other than

those bearing the RedMax mark and recommended

for the unit.

8. Under no circumstances should you ever take apart

the product or alter it in any way. Doing so might

result in the product becoming damaged during

operation or the product becoming unable to operate

properly.

■ TRANSPORTATION

• Drain the fuel from the fuel tank before transporting

or storing the blower.

• Secure the unit carefully to prevent movement when

it is transported.

•A unit that receives a strong shock during transport

and unloading may malfunction.

■ STORAGE

• When storing the blower, choose a space indoors

free from moisture and out of the reach of children.

Page is loading ...

20

6. Set up

English

■ BLOWER TUBES

1. Connect the blower and swivel joint with flexible

hose. Clamp both ends of the flexible hose securely

with the hardware supplied with the unit.

2. Align the protrusion and the groove provided on the

tube ends and twist the tube until connection is

locked up.

A light lubricant may be used to ease assembly of

flexible pipe to blower elbow.

■ THROTTLE LEVER [EBZ8001RH]

• Set up the clamp to the swivel and tighten the screw

on the clamp.

(1) Clamp

(2) Swivel

(3) Screw

■ THROTTLE CABLE [EBZ8001RH]

• Use the clamp to fasten the colgate tube containing

the throttle cable and the power cable to the hose.

(1) Clamp

(2) Cable

(3) Hose

■ WAIST BELT (OPTIONAL ACCESSORY)

• The waist belt is attached to the hooks on the left

and right sides of the frame.

• Be sure to always tighten the buckle in front of your

body.

• If you are not using a waist belt, be sure to

remove it from the unit and store it.

• There is a risk that the belt will be caught,

toppling the unit.

•There is a danger that the belt will be sucked into

the fan.

WARNING

NOTE

F1

F2 [EBZ8001RH]

F3 [EBZ8001RH]

F4

Page is loading ...

■ FUEL

• Gasoline is very flammable. Avoid smoking or

bringing any flame or sparks near fuel. Make

sure to stop the engine and allow it cool before

refueling the unit. Select outdoor bare ground for

fueling and move at least 3m (10ft) away from the

fueling point before starting the engine.

• The RedMax/Komatsu Zenoah engines are

lubricated by oil specially formulated for air-cooled 2-

cycle gasoline engine use. If Komatsu Zenoah oil is

not available, use an anti-oxidant added quality oil

expressly labeled for air-cooled 2-cycle engine use.

(JASO FC GRADE OIL or ISO EGC GRADE)

• Do not use BIA or TCW (2-stroke water-cooling type)

mixed oil.

RECOMMENDED MIXING RATIO

GASOLINE 50:OIL 1

(when using ZENOAH genuine oil)

• Exhaust emission are controlled by the

fundamental engine parameters and components

(eq., carburation, ignition timing and port timing)

without addition of any major hardware or the

introduction of an inert material during

combustion.

• These engines are certified to operate on unleaded

gasoline.

• Make sure to use gasoline with a minimum octane

number of 89 RON (USA/Canada: 87AL)

• If you use a gasoline of a lower octane value than

prescribed, there is a danger that the engine

temperature may rise and an engine problem such

as piston seizing may consequently occur.

• Unleaded gasoline is recommended to reduce the

contamination of the air for the sake of your health

and the environment.

• Poor quality gasolines or oils may damage sealing

WARNING

22

7. Fuel

English

50:1 MIXING CHART

GASOLINE gal. 1 2345

2-CYCLE OIL fl.oz 2.6 5.2 7.8 10.4 13

GASOLINE liter 1 2345

2-CYCLE OIL ml 20 40 60 80 100

Page is loading ...

24

7. Fuel

English

rings, fuel lines or fuel tank of the engine.

■ HOW TO MIX FUEL

Pay attention to agitation.

1. Measure out the quantities of gasoline and oil to be

mixed.

2. Put some of the gasoline into a clean, approved fuel

container.

3. Pour in all of the oil and agitate well.

4. Pour In the rest of gasoline and agitate again for at

least one minute. As some oils may be difficult to

agitate depending on oil ingredients, sufficient

agitation is necessary for the engine to last long. Be

careful that, if the agitation is insufficient, there is an

increased danger of early piston seizing due to

abnormally lean mixture.

5. Indicate the contents on outside of container for

easy identification. To avoid mixing up with raw

gasoline or other containers.

■ FUELING THE UNIT

1. Untwist and remove the fuel cap.

2. Put fuel into the fuel tank to 80% of the full capacity.

3. Fasten the fuel cap securely and wipe up any fuel

spillage around the unit.

1. Select bare ground for fueling.

2. Move at least 10feet (3meters) away from the

fueling point before starting the engine.

3. Stop the engine and let it cool for few minutes

before refueling the unit. At that time, be sure to

sufficiently agitate the mixed gasoline in the

container.

4. Do not smoke or place hot object near fuel.

WARNING

IMPORTANT

Page is loading ...

26

7. Fuel

English

FOR YOUR ENGINE LIFE, AVOID;

1. FUEL WITH NO OIL(RAW GASOLINE) – It will

cause severe damage to the internal engine parts

very quickly.

2. GASOHOL – It can cause deterioration of rubber

and/or plastic parts and disruption of engine

lubrication.

3. OIL FOR 4-CYCLE ENGINE USE – It can cause

spark plug fouling, exhaust port blocking, or piston

ring sticking.

4. Mixed fuels which have been left unused for a

period of one month or more may clog the

carburetor and result in the engine failing to operate

properly.

5. In the case of storing the product for a long period of

time, clean the fuel tank after rendering it empty.

Next, activate the engine and empty the carburetor

of the composite fuel.

6. In the case of scrapping the used mixed oil

container, scrap it only at an authorized repository

site.

As lot details of quality assurance, read the description

in the section Limited Warranty carefully. Moreover,

normal wear and change in product with no functional

influence are not covered by the warranty. Also, be

careful that, if the usage in the instruction manual is not

observed as to the mixed gasoline, etc. described

therein, it may not be covered by the warranty.

NOTE

Page is loading ...

28

8. Operation

English

■ CONTROL ARM [EBZ8001] (F5)

• Hold the upper end of the control arm in hand and,

while pulling it away from the unit, rotate arm forward

(anti-clockwise as the arrow direction) until it clicks.

(The first position)

And if you want, you can rotate arm more forward

until it clicks. (The second position)

Choose the arm position according to your working

condition.

• To fold the arm, reverse the order.

(1) The First Position

(2) The Second Position

■ STARTING ENGINE

• Avoid operating the blower with the flexible tube

and swivel joint disconnected. That will reduce

the cooling air and the engine could be damaged

by overheating.

1. Push the primer bulb until fuel flows out in the clear

tube. (F7)

2. When the engine is cool, close the choke. (F7)

(1) Choke Lever

(2) Primer Bulb

(3) OPEN

(4) CLOSE

3. [EBZ8001RH]

Set the ignition switch to the start position. (F8)

4. Set the throttle lever in about 1/3 open position.

(F8)(F9)

(1) Full Throttle

(2) About 1/3 Open

(3) Idling

(4) Ignition Switch

5. To start, hold the top of the blower firmly with your

left hand. Pull the starter knob slowly until you feel it

engage and then give it a vigorous strong pull. (F10)

• Avoid pulling the starter rope out to its full

extent and allowing the starter rope to snap

back. This will prevent premature damage to the

starter.

• Do not let a person stand near the blower or the

IMPORTANT

F5 [EBZ8001]

(1)

(2)

(1)

(2)

(3)

F9 [EBZ8001]

F10

(1)

(2)

(3)

(4)

F8 [EBZ8001RH]

(1)

(2)

(3)

(4)

F7

Page is loading ...

30

8. Operation

English

exhaust port.

6. Once the engine is running, gradually open the

choke if it was set closed, and let the engine run at

idle speed for a minute to warm it up.

When the engine fails to start after several attempts

due to overchoking, open the choke and repeat pulling

the rope.

■ ADJUSTING IDLE SPEED (F11)

• The idling speed is set for 2000 rpm at the factory. If

it is necessary to adjust the idle speed, use the

adjustment screw on the top side of carburetor.

(1) Idling Adjustment Screw

■ STOPPING ENGINE

[EBZ8001]

• Move the throttle lever to the idling position and

press the stop switch (red button). The machine has

the mechanism that once the stop button is pushed

the plug won't give off sparks until the engine stops.

(F12)

(1) Stop Switch

[EBZ8001RH]

• Move the throttle lever to the idling position and set

the ignition switch to the stop position. (F13)

(1) Ignition Switch

If the engine won’t stop when setting the ignition

switch to the stop position, close the choke lever

and stop the engine.

In this case, please repair the machine at your

nealest servicing dealer. (F14)

(1) Choke Lever

(2) OPEN

(3) CLOSE

NOTE

(1)

F11

(1)

F12 [EBZ8001]

(1)

F13 [EBZ8001RH]

(1)

(2)

(3)

F14

Page is loading ...

32

Maintenance, replacement, or repair of the

emission control device and systems may be

performed by any non-road engine repair

establishment or individual.

9. Maintenance

English

Make sure that the engine has stopped and is cool

before performing any service to the blower.

Contact with rotating blower fan or hot muffler may

result in a personal injury.

■ AIR CLEANER

• Never operate the blower without an air filter or with

a deformed or broken filter element because

unfiltered dusty air will quickly ruin the engine.

• Check the air cleaner before use.

A clogged air filter may increase fuel consumption

while cutting down the engine power.

• Never clean a paper filter by striking it with or

against another object. The filter may be damaged

and resultant dust contamination can diminish

engine performance.

WARNING

Daily Every Every Every

System/Compornent Procedure or 25 hours 50 hours 100 hours

Before use after after after

Air Filter Inspect/Clean

✔

Inspect/Replace

✔

Fuel Leaks Inspect/Replace

✔

Fuel Filter Inspect/Replace

✔✔

Fuel Line Inspect/Clean

✔

Spark Plug Inspect/Clean

✔

Muffler Inspect/Clean

✔

Muffler Spark Arrester Inspect/Clean

✔

Cooling System Inspect/Clean

✔

Screws/Nuts/Bolts Tighten

✔

Cylinder Exhaust Port Inspect/Clean

✔

Prefilter

Paper Filter

Page is loading ...

34

9. Maintenance

English

CLEANING AIR FILTER:

1. Unscrew 2 knob bolts and remove the air cleaner

cover. Then remove a prefilter mounted inside the air

cleaner cover.

(1) Knob Bolt

(2) Prefilter

(3) Inner Case

(4) Paper Filter

2. Wash the prefilter in fresh, non flammable cleaning

solution (ex. warm soapy water) and then dry.

(Clean the air filter once in a week.)

3. Exchange the paper filter element with new one in

case it has been contaminated.

• This prefilter is dry type.

• Never wash the prefilter in oleaginous cleaning

solution.

• Do not clean a paper filter by striking it.

■ FUEL FILTER

•A clogged fuel filter may cause poor acceleration of

the engine. Check periodically to see if the filter is

clogged with dirt. The filter can be taken out of the

fueling port using a small wire hook. Disconnect the

filter assembly from the fuel pipe and unhook the

retainer to disassemble it. Clean the components

with gasoline.

(1) Screen

(2) Element

(3) Holder

(4) Retainer

■ SPARK PLUG

• The spark plug may gather carbon deposits on its

firing end with reasonable use. Remove and inspect

the spark plug every 25 hours and clean the

electrodes as necessary with a wire brush. The spark

gap should be adjusted to .025 in (0.6~0.7mm).

• Plug manufacturers recommend replacing the plug

twice a year to avoid unexpected plug failure in a job.

REPLACEMENT PLUG IS A NGK CMR7H.

WARNING

F16

F17

F15

Page is loading ...

36

9. Maintenance

English

• Note that using any spark plugs other than those

designated may result in the engine failing to

operate properly or in the engine becoming

overheated and damaged.

• To install the spark plug, first turn the plug until it is

finger tight, then tighten it a quarter turn more with a

socket wrench.

■ MUFFLER

• Inspect periodically, the muffler for loose fasteners,

any damage or corrosion. If any sign of exhaust

leakage is found, do not use the blower and have it

repaired immediately.

• Note that failing to do so may result in the

engine catching on fire.

• Before starting operation, always make sure to

check if the muffler is properly held by three bolts

(F18 (2)). (Fastening Torque : 8 to 12 N·m)

• Also make sure that the speak arrester and the

diffuser are properly attached with four bolts (F18

(1)). (Fastening Torque : 2 to 3 N·m)

• Even if one of seven bolts is loose, it may result in

engine catching on fire.

(1) Bolt

(2) Bolt

(3) Spark arrester

(4) Diffuser

■ SPARK ARRESTER

• The muffler is equipped with a spark arrester to

prevent red hot carbon from flying out of the exhaust

outlet. Periodically inspect and clean as necessary

with a wire brush. In the State of California it is

required by law (Section 4442 of the California Pulic

Resources Code) to equip a spark arrester when a

gas powered tool is used in any forest covered, bush

covered, or grass covered unimproved land.

IMPORTANT

WARNING

IMPORTANT

F18

Page is loading ...

38

9. Maintenance

English

■ PROCEDURES TO BE PERFORMED AFTER

EVERY 100 HOURS OF USE

1. Remove the muffler, insert a screwdriver into the

vent, and wipe away any carbon buildup. Wipe away

any carbon buildup on the muffler exhaust vent and

cylinder exhaust port at the same time.

2. Tighten all screws, bolts, and fittings.

■ AIR INLET NET

• Blowing air is taken in from the air inlet net. When air

flow has dropped down during operation, stop the

engine and inspect the air inlet net for blocking by

obstacles.

• Note that failure to remove any such obstacles may

result in the engine becoming overheated and

damaged.

(1) Net

Never use the blower without the net of the blower.

Before each use, check that the net is attached in

place and is free from any damage.

■ IGNITION COIL AIR GAP INSPECTION

•If the gap is out of standard or when installing the

coil or rotor, adjust the air gap between the ignition

coil and the iron core of the rotor.

Air Gap:

0.40mm (0.35 ~ 0.45mm)

0.016" (0.014 ~ 0.017")

(1) Rotor

(2) Ignition coil

WARNING

IMPORTANT

F21

(1)

F20

F19

Page is loading ...

RedMax EBZ8001 User manual

RedMax EBZ8001 User manual

in other languages

Related papers

Other documents