Sparky X 52E User manual

www.sparky.eu

500 W

X 52E

1 – 8

ROUTER

Original instructions

18 – 27

DEFONCEUSE

Notice originale

65 – 74

ФРЕЗА

Оригинальная инструкция по эксплуатации

9 – 17

OBERFRÄSE

Originalbetriebsanleitung

Оригінальна інструкція з експлуатації

75 – 84

ФРЕЗА

56 – 64

FREZARKA

Oryginalna instrukcja obsługi

47 – 55

TUPIA

Manual original

28 – 36

FRESATRICE

Istruzioni originali

37 – 46

FRESADORA

Instrucciones de uso originales

Оригинална инструкция за използване

85 – 94

ФРЕЗА

20 January 2016

Manufacturer

SPARKY Power Tools GmbH

Leipziger Str. 20

10117 Berlin, GERMANY

Signature of authorized person

A. Ivanov

Technical director of SPARKY ELTOS AG

DECLARATION OF CONFORMITY

We declare under our sole responsibility that this product fulls all the relevant provisions of the following directives and the harmonized

standards: 2006/42/ЕС, 2004/108/EC (until April 19, 2016), 2014/30/EU (from April 20, 2016), 2011/65/EU,

EN 60745-1, EN 60745-2-17; EN 55014-1, EN 55014-2, EN 61000-3-2, EN 61000-3-3.

Technical le is stored at SPARKY ELTOS AG, Koubrat Str. 9, 5500 Lovetch, Bulgaria.

KONFORMITÄTSERKLÄRUNG

Hiermit versichern wir unsere persönliche Haftung, dass dieses Erzeugnis allen einschlägigen Bestimmungen folgender Richtlinien und

entsprechender harmonisierten Standards entspricht: 2006/42/ЕС, 2004/108/EC (bis 19. April 2016), 2014/30/EU (ab 20. April 2016),

2011/65/EU, EN 60745-1, EN 60745-2-17; EN 55014-1, EN 55014-2, EN 61000-3-2, EN 61000-3-3.

Die technischen Unterlagen werden bei SPARKY ELTOS AG, Kubrat Str.9, 5500 Lovetch, Bulgarien, aufbewahrt.

DECLARATION DE CONFORMITE

Nous déclarons sous notre responsabilité que ce produit satisfait à l’ensemble des dispositions pertinentes de la présente directives,

respectivement aux normes harmonisées: 2006/42/ЕС, 2004/108/EC (jusqu’au 19 avril 2016), 2014/30/EU (à partir du 20 avril 2016),

2011/65/EU, EN 60745-1, EN 60745-2-17; EN 55014-1, EN 55014-2, EN 61000-3-2, EN 61000-3-3.

Le dossier technique est conservé par SPARKY ELTOS AD, 9, rue Kubrat, Lovech, Bulgarie.

DICHIARAZIONE DI CONFORMITÀ

Noi dichiariamo sotto la nostra personale responsabilità, che questo prodotto è in conformità a tutte le disposizioni pertinenti della presente

direttive e norme armonizzate: 2006/42/ЕС, 2004/108/EC (no al 19 aprile 2016), 2014/30/UE (dal 20 aprile 2016), 2011/65/EU, EN 60745-1,

EN 60745-2-17; EN 55014-1, EN 55014-2, EN 61000-3-2, EN 61000-3-3.

Il fascicolo tecnico viene custodito presso la SPARKY ELTOS AD, 5500 Lovech, via Kubrat n. 9, Bulgaria.

DECLARACIÓN DE CONFORMIDAD

Declaramos bajo nuestra exclusiva responsabilidad que este producto está conforme con todas las disposiciones aplicables de la presente

directrices aplicables y las correspondientes normas armonizadas: 2006/42/ЕС, 2004/108/EC (hasta el 19 de Abril de 2016), 2014/30/EU (a

partir del 20 de Abril de 2016), 2011/65/EU, EN 60745-1, EN 60745-2-17; EN 55014-1, EN 55014-2, EN 61000-3-2, EN 61000-3-3.

El expediente técnico está archivado en SPARKY ELTOS SA, C/ Kubrat, 9, 5500 Lovech, Bulgaria.

DECLARAÇÃO DE CONFORMIDADE

Declaramos assumindo a nossa responsabilidade pessoal que este produto está conforme com todas as disposições relevantes da presente

directrizes aplicáveis e respectivos estandartes harmonizados: 2006/42/ЕС, 2004/108/EC (até ao 19 de Abril do 2016), 2014/30/EU (a partir do

20 de Abril do 2016), 2011/65/EU, EN 60745-1, EN 60745-2-17; EN 55014-1, EN 55014-2, EN 61000-3-2, EN 61000-3-3.

A documentação técnica guarda-se no SPARKY ELTOS AD, rua Kubrat 9, 5500, Lovech, Bulgária.

DEKLARACJA ZGODNOŚCI

Niniejszym deklarujemy naszą osobistą odpowiedzialnością, że ten produkt spełnia wszystkie odpowiednie postanowienia następujących

dyrektyw i harmonizowanych standardów: 2006/42/ЕС, 2004/108/EC (do 19 kwietnia 2016), 2014/30/EU (od 20 kwietnia 2016), 2011/65/EU,

EN 60745-1, EN 60745-2-17; EN 55014-1, EN 55014-2, EN 61000-3-2, EN 61000-3-3.

Teczka techniczna przechowywana jest w SPARKY ELTOS AG, Kubrat Str.9, 5500 Lovetch, Bułgaria.

ДЕКЛАРАЦИЯ О СООТВЕТСТВИИ

Мы заявляем со всей ответственностью, что данный продукт полностью соответствует всем соответствующим требованиям действующих

директив и гармонизированных стандартов: 2006/42/ЕС, 2004/108/EC (до 19 апреля 2016), 2014/30/EU (с 20 апреля 2016), 2011/65/EU,

EN 60745-1, EN 60745-2-17; EN 55014-1, EN 55014-2, EN 61000-3-2, EN 61000-3-3.

Техническое досье хранится в СПАРКИ ЕЛТОС АД, ул. Кубрат №9, 5500 Ловеч, Болгария.

ДЕКЛАРАЦІЯ ПРО ВІДПОВІДНІСТЬ

Ми заявляємо під свою власну відповідальність, що даний продукт відповідає всім діючим вимогам директив і гармонізованих стандартів:

2006/42/ЕС, 2004/108/EC (до 19 квітня 2016), 2014/30/EU (з 20 квітня 2016), 2011/65/EU,

EN 60745-1, EN 60745-2-17; EN 55014-1, EN 55014-2, EN 61000-3-2, EN 61000-3-3.

Технічне досьє зберігається в СПАРКИ ЕЛТОС АД, ул. Кубрат № 9, 5500 Ловеч, Болгарія.

ДЕКЛАРАЦИЯ ЗА СЪОТВЕТСТВИЕ

Ние декларираме на своя лична отговорност, че това изделие отговаря на всички приложими изисквания на следните директиви и

хармонизирани стандарти: 2006/42/ЕС, 2004/108/EC (до 19 април 2016), 2014/30/EU (от 20 април 2016), 2011/65/EU,

EN 60745-1, EN 60745-2-17; EN 55014-1, EN 55014-2, EN 61000-3-2, EN 61000-3-3.

Техническото досие се съхранява в СПАРКИ ЕЛТОС АД, ул. Кубрат №9, 5500 Ловеч, България.

BLACK PANTONE185

BА

5

14

15

1

2

3

12

13

4

8

9

11

6

7

10

BLACK PANTONE185

1

EN

Introduction

Your new SPARKY power tool will more than satisfy your expectations. It has been manufactured

under stringent SPARKY Quality Standards to meet superior performance criteria. You will nd your

new tool easy and safe to operate, and, with proper care, it will give you many years of dependable

service.

WARNING:

Carefully read through these Original Instructions before using your new SPARKY power tool.

Take special care to heed the Warnings. Your SPARKY power tool has many features that will

make your job faster and easier. Safety, performance, and dependability have been given top

priority in the development of this tool, making it easy to maintain and operate.

Do not dispose of electric tools together with household waste!

Waste electrical products should not be disposed of with household waste. Please recycle

where facilities exist. Check with your local authority or retailer for recycling advice.

ENVIRONMENTAL PROTECTION

The machine, accessories and packaging should be sorted for environmental-friendly

recycling.

The plastic components are labelled for categorised recycling.

UNPACKING

Due to modern mass production techniques, it is unlikely that your power tool is faulty or that a part is

missing. If you nd anything wrong, do not operate the tool until the parts have been replaced or the

fault has been rectied. Failure to do so could result in serious personal injury.

ASSEMBLY

The router is packed, fully assembled except for the dust extraction adapter and parallel guide.

Contents

Introduction ............................................................................................................................... 1

Technical specications ...........................................................................................................3

General power tool safety warnings ...........................................................................................4

Router safety warnings .............................................................................................................. 5

Know your product ................................................................................................................ A/6

Operation .................................................................................................................................. 6

Maintenance .............................................................................................................................8

Warranty ....................................................................................................................................8

X 52E ● Original instructions

2

EN

X 52E

DESCRIPTION OF SYMBOLS

The rating plate on your power tool may show symbols. These represent important information about

the product or instructions on its use.

Double insulated for additional protection.

Electronic speed pre-selection.

Connection to vacuum cleaner.

Conforms to the relevant European Directives.

Conforms to the requirements of Customs Union regulations.

Conforms to the requirements of Ukrainian standards.

Refer to Original Instructions.

YYYY-Www Production period, where the variable symbols are:

YYYY- year of manufacture,

ww - calendar week number.

X Router.

3

Original instructions

EN

The vibration emission level given in this information sheet has been measured in accordance with

a standardised test given in EN 60745 and may be used to compare one tool with another. It may be

used for a preliminary assessment of exposure.

The declared vibration emission level represents the main applications of the tool. However if the tool

is used for different applications, with different accessories or poorly maintained, the vibration emis-

sion may differ. This may signicantly increase the exposure level over the total working period.

An estimation of the level of exposure to vibration should also take into account the times when the

tool is switched off or when it is running but not actually doing the job. This may signicantly reduce

the exposure level over the total working period.

Maintain the power tool and the accessories and keep your hands warm during operation to reduce

the harmful effect of vibrations.

Dust from material such as paint containing lead, some wood species, minerals and metal may be

harmful. Contact with or inhalation of the dust may cause allergic reactions and/or respiratory dis-

eases to the operator or bystanders.

Certain kinds of dust are classied as carcinogenic such as oak and beech dust especially in conjunc-

tion with additives for wood conditioning (chromate, wood preservative). Material containing asbestos

must only be treated by specialists.

▪ Where the use of a dust extraction device is possible it shall be used.

▪ To achieve a high level of dust collection, use vacuum cleaner for wood or for wood and/or minerals

together with this tool.

▪ The work place must be well ventilated.

▪ The use of a dust mask of lter class P2 is recommended.

Follow national requirements for the materials you want to work with.

Technical specications

Model X 52E

Power input 500 W

No load speed 8000-33000 min

-1

Electronic speed pre-selection yes

Connection to vacuum cleaner yes

Collet capacity Ø6; Ø8 mm

Cutting stroke, max. 52 mm

Weight (EPTA Procedure 01/2014) 2.8 kg

Protection class (EN 60745-1)

II

NOISE AND VIBRATION INFORMATION

Measured values determined according to EN 60745.

Noise emission

A-weighted sound pressure level L

pA

82.0 dB (A)

Uncertainty К

pA

3.0 dB (A)

A-weighted sound power level L

wA

93.0 dB (A)

Uncertainty К

wA

3.0 dB (A)

Wear hearing protection!

Vibration emission *

Total vibration values (vector sum in the three axes) determined according to EN 60745:

Cutting grooves in chipboard

Vibration emission value a

h

3.5 m/s

2

Uncertainty К 1.5 m/s

2

* The vibration emission values are determined according to 6.2.7 EN 60745.

4

EN

X 52E

General power tool

safety warnings

WARNING! Read all safety warnings

and all instructions. Failure to follow the

warnings and instructions may result in

electric shock, re and/or serious injury.

Save all warnings and instructions for

future reference.

The term “power tool” in the warnings refers

to your mains-operated (corded) power tool or

battery-operated (cordless) power tool.

1) Work area safety

a) Keep work area clean and well lit. Clut-

tered or dark areas invite accidents.

b) Do not operate power tools in explosive

atmospheres, such as in the presence

     

Power tools create sparks which may ignite

the dust or fumes.

c) Keep children and bystanders away

while operating a power tool. Distrac-

tions can cause you to lose control.

2) Electrical safety

a) Power tool plugs must match the outlet.

Never modify the plug in any way. Do

not use any adapter plugs with earthed

(grounded) power tools. Unmodied

plugs and matching outlets will reduce risk

of electric shock.

b) Avoid body contact with earthed or

grounded surfaces, such as pipes, ra-

diators, ranges and refrigerators. There

is an increased risk of electric shock if your

body is earthed or grounded.

c) Do not expose power tools to rain or wet

conditions. Water entering a power tool

will increase the risk of electric shock.

d) Do not abuse the cord. Never use the

cord for carrying, pulling or unplugging

the power tool. Keep cord away from

heat, oil, sharp edges or moving parts.

Damaged or entangled cords increase the

risk of electric shock.

e) When operating a power tool outdoors,

use an extension cord suitable for out-

door use. Use of a cord suitable for out-

door use reduces the risk of electric shock.

f) If operating a power tool in a damp lo-

cation is unavoidable, use a residual

current device (RCD) protected supply.

Use of an RCD reduces the risk of electric

shock.

3) Personal safety

a) Stay alert, watch what you are doing

and use common sense when operating

a power tool. Do not use a power tool

       -

ence of drugs, alcohol or medication.

A moment of inattention while operating

power tools may result in serious personal

injury.

b)    

Always wear eye protection. Protective

equipment such as dust mask, non-skid

safety shoes, hard hat, or hearing protec-

tion used for appropriate conditions will re-

duce personal injuries.

c) Prevent unintentional starting. Ensure

the switch is in the off-position before

connecting to power source and/or bat-

tery pack, picking up or carrying the

tool. Carrying power tools with your nger

on the switch or energising power tools that

have the switch on invites accidents.

d) Remove any adjusting key or wrench be-

fore turning the power tool on. A wrench

or a key left attached to a rotating part of

the power tool may result in personal in-

jury.

e) Do not overreach. Keep proper footing

and balance at all times. This enables

better control of the power tool in unexpect-

ed situations.

f) Dress properly. Do not wear loose cloth-

ing or jewellery. Keep your hair, cloth-

ing and gloves away from moving parts.

Loose clothes, jewellery or long hair can be

caught in moving parts.

g) If devices are provided for the connec-

tion of dust extraction and collection fa-

cilities, ensure these are connected and

properly used. Use of dust collection can

reduce dust-related hazards.

4) Power tool use and care

a) Do not force the power tool. Use the cor-

rect power tool for your application. The

correct power tool will do the job better and

safer at the rate for which it was designed.

b) Do not use the power tool if the switch

does not turn it on and off. Any power tool

that cannot be controlled with the switch is

dangerous and must be repaired.

c) Disconnect the plug from the power

source and/or the battery pack from the

power tool before making any adjust-

ments, changing accessories, or stor-

5

Original instructions

EN

ing power tools. Such preventive safety

measures reduce the risk of starting the

power tool accidentally.

d) Store idle power tools out of the reach

of children and do not allow persons

unfamiliar with the power tool or these

instructions to operate the power tool.

Power tools are dangerous in the hands of

untrained users.

e) Maintain power tools. Check for mis-

alignment or binding of moving parts,

breakage of parts and any other condi-

tion that may affect the power tool’s op-

eration. If damaged, have the power tool

repaired before use. Many accidents are

caused by poorly maintained power tools.

f) Keep cutting tools sharp and clean.

Properly maintained cutting tools with

sharp cutting edges are less likely to bind

and are easier to control.

g) Use the power tool, accessories and

tool bits etc. in accordance with these

instructions, taking into account the

working conditions and the work to be

performed. Use of the power tool for op-

erations different from those intended could

result in a hazardous situation.

5) Service

a) Have your power tool serviced by a

-

tical replacement parts. This will ensure

that the safety of the power tool is main-

tained.

Router safety

warnings

Wear ear protectors with

router

. Expo-

sure to noise can cause hearing loss.

▪ Always use both handles during operation.

Loss of control can cause personal injury.

During operation provide eye protec-

-

ing particles. Wear goggles.

Take protective measures against inha-

lation of dust. Some materials can contain

toxic ingredients. Wear a dust mask and work

with dust/chip extraction when connectable.

▪ Hold the power tool by insulated gripping

surfaces only, when performing an op-

eration where the cutting accessory may

contact hidden wiring or its own cord. Cut-

ting accessory contacting a “live” wire may

make exposed metal parts of the power tool

“live” and could give the operator an electric

shock.

▪ Use clamps or another practical way to se-

cure and support the workpiece to a stable

platform. Holding the work by your hand or

against the body leaves it unstable and may

lead to loss of control.

▪ Do not process materials containing asbes-

tos. Asbestos is considered carcinogenic.

▪ Use of protective gloves is recommended.

WARNING: Before connecting a tool

to a power source, ensure that the voltage

supply is the same as the one specied on

the name-plate of the tool.

▪ A power source with a voltage greater than

that specied for the tool can result in serious

injury to the user, as well as damage to the

tool.

▪ If in doubt, do not plug in the tool.

▪ Using a power source with a voltage less than

the nameplate rating is harmful to the motor.

▪ Fully unwind cable drum extensions to avoid

potential overheating.

▪ When an extension cable is required, you

must ensure that it has the right ampere rating

for your power tool and it is in safe electrical

condition.

WARNING: Always switch off and un-

plug the power tool prior to any adjustment,

servicing or maintenance or in case of mains

drop-out.

▪ Prior to operation remove all nails, screws

and other objects from the work piece. You

can damage the bit and the tool by cutting

into a nail or other metal. It can also present a

safety hazard.

▪ Never operate the router under load. Make

sure that the bit is not in contact with the work

piece when you switch the machine on.

▪ Always use both handles and make sure that

you have a good grip on the router before pro-

ceeding with any work.

▪ Always switch off and wait until the bit has

come to a complete standstill before remov-

ing the machine from the work piece.

▪ Do not touch the bit immediately after opera-

tion. It may be extremely hot and could burn

your skin.

6

EN

X 52E

▪ Rags, cloths, cord, string and the like should

never be left around the work area.

▪ Always keep the cord away from the working

area of the power tool.

▪ Never use the machine with a damaged ca-

ble. Do not touch the damaged cable and pull

the mains plug when the cable is damaged

while operating. Damaged cables increase

the risk of electric shock.

▪ Do not use blunt or damaged router bits. Blunt

or damaged router bits cause increased fric-

tion, can become jammed and lead to imbal-

ance.

▪ The tool must be used only for its prescribed

purpose. Any use other than those mentioned

in this Manual will be considered a case of

misuse. The user and not the manufacturer

shall be liable for any damage or injury result-

ing from such cases of misuse.

▪ To use this tool properly, you must observe

the safety regulations, the assembly instruc-

tions and the operating instructions found in

this Manual. All persons who use and service

the machine have to be acquainted with this

Manual and must be informed about its poten-

tial hazards. Children and frail people must not

use this tool. Children should be supervised

at all times if they are in the area in which the

tool is being used. It is also imperative that

you observe the accident prevention regula-

tions in force in your area. The same applies

for general rules of occupational health and

safety.

▪ The manufacturer shall not be liable for any

changes made to the tool nor for any damage

resulting from such changes.

▪ Power tools must not be used outdoors in

rainy weather, or in moist environment (after

rain) or in close vicinity with easily ammable

liquids and gases. The working place should

be well lit.

Know your product

Before using the power tool, familiarize your-

self with all the operating features and safety

requirements.

Use the tool and accessories only for the ap-

plications intended. All other applications are

expressly ruled out.

1. ON/OFF switch

2. Cutting (shaping) depth guide

3. Knee vertical position xing lever

4. Grip handles

5. Screw for tightening the electric motor

to the knee

6. Three-level position support

7. Parallel guide ruler

8. Base plate

9. Spindle

10. Parallel guide

11. Screws for securing the parallel guide

12. Vertical guides

13. Cutting (shaping) depth reading ruler

14. Electronic regulator of rotation speed

15. Adapter for vacuum cleaner

Operation

These power tools are supplied from single-

phase alternating current mains only. They

are double insulated according to EN 60745-1,

IEC 60745 and can be connected to grounded

or not grounded sockets. This power tool is radio

suppressed in compliance with EMC Directive.

The routers are power tools, designed for rout-

ing groove, roundover, cone, chamfering, prole

edges and openings in wood, wooden planes

and plastics, by means of straight and prole

router bits.

PRIOR TO INITIAL OPERATION

▪ Make sure the power supply voltage corre-

sponds to the value indicated on the name

plate with the technical data of the tool.

▪ Always check the position of ON/OFF switch.

The router must be connected to the power

supply socket only when this switch is in OFF

position.

▪ Make sure that the cord and the plug are in

order. If the replacement of the supply cord is

necessary, this has to be done by the manu-

facturer or his agent in order to avoid a safety

hazard.

▪ Before starting to operate, ensure the router

bit being used has the correct shank size

matching the inserted collet and the maxi-

mum number of revolutions of the used tool.

▪ Make sure if the router bit is secured in the

collet.

WARNING: Always switch off and

unplug the power tool prior to any adjustment,

servicing or maintenance.

The router is designated to operate with router

bits with shank diameter 6 and 8 mm. The maxi-

mum diameter of the router bit active part shall

not exceed Ø30. The high speed requires usage

7

Original instructions

EN

of high-quality router bits in order to guarantee

sufcient operating life (E.g. HSS router bits or

even better carbide tipped bits.)

Use only router bits with exact shank diameter,

fîr to the corresponding collet and appropriate

for the router speed.

SWITCHING ON - SWITCHING OFF

▪ Switching on: push the slider of ON/OFF

switch 1 forward until its front end will sag,

thus xing itself.

▪ Switching off: press the back, lifted end of

switch 1 and release it to return in its initial

position.

WARNING: In case ambient tem-

perature is lower than 0

o

C the router must be

switched on only in “G” position of the speed

electronic regulator. After several minutes op-

eration at no-load the router can be used also

in the rest of regulator positions.

ROTATION SPEED ADJUSTMENT

Rotation speed adjustment can be varied

smoothly from A to G, through rotating the thum-

bwheel of the electronic regulator 14, placed on

the rear of the electric motor cover.

HANDLE ADJUSTMENT

Pull out the handles separately and rotate them

in position, convenient for operation , then re-

lease the handles .

REPLACING THE ROUTER BITS

Unscrew xing screw 5 to remove the electric

motor from the supporting base, in order to

work more conveniently.

Unscrew nut III by means of the wrenches S17

and S14 and remove router bit IV from the

spindle 9.

Place the new bit in collet II and tighten nut III

completely.

Replace the electric motor in the supporting

knee cradle and tighten xing screw 5 well

ADJUSTMENT OF CUTTING DEPTH

Lower down supporting knee until the tool will

touch the surface of the machined piece, x it by

lever 3, and read the position on vertical ruler 13

as initial (zero) position.

Adjust the rst depth level by guide 2, pointing to

the highest level of the three-position support 6,

reading the size on vertical ruler 13 and x the

supporting knee with lever 3.

Fix depth guide 2 by the wing screw. (Adjust in

advance the three levels of the positioning sup-

port to the desired levels.)

- The second and the third level of cutting depth

can be achieved by only rotating the disk of the

three-position support 6 and moving the support

knee until depth guide 2 will touch the corre-

spon-ding level of the support.

Check the sizes on the vertical ruler or by a ref-

erence part (test part).

USAGE OF THE PARALLEL GUIDE

The parallel guide 10 is used for cutting edges

and grooves parallel to them at a predened dis-

tance. Adjusting the distance is accomplished by

using horizontal ruler 7, after that parallel guide

10 being xed with screws 11.

ROUTING AGAINST DRAWING

(DRAFT)

It is performed without parallel guide 10, against

the preliminary drawn on the workpiece draft.

Better results can be achieved if machining

smaller lengths.

ROUTING BIG WORKPIECES

In order to guide the router bit use an auxiliary

board xed on the machined surface. Guide the

router with both hands, the at part of the router

base 8 being constantly pressed against the

auxiliary board.

ROUTING WITH SUCTION

Place the adapter in the cradle in base 8, from

its lower side, cylindrical part pointing forward.

Fix the adapter to the base with two screws and

place the transparent cover. The inner diameter

of the adapter for connecting to the vacuum-

cleaner is equal to 35 mm.

ACCESSORIES TO BE USED WITH

THIS POWER TOOL

▪ HSS router bits - Ø6; Ø8

▪ Carbide tipped bits - Ø6; Ø8

8

EN

X 52E

Maintenance

WARNING: Always ensure that the

tool is switched off and unplugged before

attempting to perform inspection or mainte-

nance.

BRUSH REPLACEMENT

This power tool is equipped with auto-stop

brushes. When the carbon brushes are worn

out, the machine switches itself off. In this case

both brushes must be replaced simultaneously

with genuine brushes at SPARKY service centre

for warranty and post-warranty service.

GENERAL INSPECTION

Regularly inspect all fasteners and ensure they are

properly tightened. Should any of the screws be

loose, retighten it immediately to avoid hazards.

If the replacement of the supply cord is neces-

sary, this has to be done by the manufacturer or

his agent in order to avoid a safety hazard.

CLEANING

For safe operation always keep the machine

and its ventilation slots clean.

Regularly check to see if any dust or foreign mat-

ter has entered the ventilation slots and the grills

around the switches. Use a soft brush and/or air

jet to remove any accumulated dust. Wear safety

glasses to protect your eyes whilst cleaning.

Maintain threaded sockets clean.

Clean regularly and lubricate periodically verti-

cal guides 12 with oil.

Exterior plastic parts may be cleaned with a

damp cloth and mild detergent if necessary.

WARNING: Never use alcohol, petrol

or other cleaning agent. Never use caustic

agents to clean plastic parts.

WARNING: Water must never come

into contact with the tool.

IMPORTANT! To assure product safety and re-

liability, repairs, maintenance and adjustment

(including brush inspection and replacement)

should be performed by certied service centres

or other qualied service organisations, always

using genuine replacement parts.

Warranty

The guarantee period for SPARKY power tools

is determined in the guarantee card.

Faults due to normal wear, overloading or im-

proper handling will be excluded from the guar-

antee.

Faults due to defective materials implemented

as well as defects in workmanship will be cor-

rected free of charge through replacement or

repair.

The complaints for defective SPARKY power

tools will be recognized if the machine is sent

back to the dealer or is presented to the author-

ised warranty service centre undismantled, in its

initial condition.

Notes

Carefully read the entire Instruction Manual be-

fore using this product.

The manufacturer reserves the right to make

changes and improvements to the products and

to alter specications without prior notice.

Specications may differ from country to coun-

try.

Page is loading ...

Sparky X 52E User manual

Sparky X 52E User manual

in other languages

Related papers

Other documents