PSG PF09010 is a multifunctional portable digital microscope with a 5-inch color LCD screen. It has a magnification range of 20x to 500x and a built-in 2-megapixel camera. It can be used for a wide variety of applications, including:
- PCB inspection: The high magnification and built-in camera make it ideal for inspecting printed circuit boards (PCBs) for defects.
- Soldering and rework: The microscope can be used to inspect solder joints and perform rework tasks.
- Quality control: The microscope can be used to inspect products for quality control purposes.
- Education and research: The microscope is a valuable tool for students and researchers in a variety of fields.
PSG PF09010 is a multifunctional portable digital microscope with a 5-inch color LCD screen. It has a magnification range of 20x to 500x and a built-in 2-megapixel camera. It can be used for a wide variety of applications, including:
- PCB inspection: The high magnification and built-in camera make it ideal for inspecting printed circuit boards (PCBs) for defects.
- Soldering and rework: The microscope can be used to inspect solder joints and perform rework tasks.
- Quality control: The microscope can be used to inspect products for quality control purposes.
- Education and research: The microscope is a valuable tool for students and researchers in a variety of fields.
OPTIONAL ELECTRIC ELEMENT
INSTALLATION
(15 or 20 kW)
CADDY ALTERNA II FURNACE
45819A
Printed in Canada 13-08-2015
This manual is available for free download on the manufacturer’s web site. It is a copyrighted document.
Re-sale is strictly prohibited. The manufacturer may update this manual from time to time and cannot be
responsible for problems, injuries, or damages arising out of the use of information contained in any
manual obtained from unauthorized sources.
OPTIONAL ELECTRIC ELEMENT INSTALLATION
Your Caddy Alterna II furnace can be installed with an optional electric element
(15 or 20 kW). This option can be installed on either side of your furnace (right or left).
The installation must be performed by a qualified professional.
Please note that the installation procedure is carried out in an identical way no matter which
electric element is used (15kW or 20kW) or the chosen installation side (right or left).
RIGHT SIDE INSTALLATION
LEFT SIDE INSTALLATION
1
Remove cover for the electrical unit
option (B) located on the desired
side of the furnace by lifting the
panel upward slightly and then
pulling it toward you to release it
from its notches (A) holding it in
place. You may dispose of the
cover.
2
Remove the panel from the
electric element box (D). Keep
the screws (C).
CAUTION:
Before installing the unit inside the furnace, it is advised to do the wiring connections of
the element and its connection to the power board (See Appendix A). Please note that in
order to use a single circuit breaker for the electrical unit and the power board, it is
possible to hook up the power board from the electric element (see Appendix B).
3
Once the wiring connections
made (See Appendix A
and/or Appendix B), you may
install the electric element
box inside the furnace.
4
To secure the electric
element box in place, use
the six screws (A) included
with the electric unit.
5
Secure the panel from the electric
element box (D) with the 8 screws
(C) kept from step 2.
Annexe A
Electrical wiring and power board connections
1
Use two wires (18 ga) (not included).
Skinned at both ends.
2
Connect the 2 wires to the « EHT » terminal of the power board up to the terminal on the
electrical element.
3
Hook up the main electrical supply to terminal L1, N, L2, G located on the electrical element.
Annexe B
Power supply of the power board from the electric element
CAUTION:
When supplying the power of the power board from the electrical element, always use
the fuse (F) that is included with the electric element box.
For the electrical connection and the connection to the power board please follow the 3
steps in Appendix A.
STOVE BUILDER INTERNATIONAL INC.
250, de Copenhague, Saint-Augustin-de-Desmaures (Quebec), Canada G3A 2H3
Tel: (418) 878-3040
Fax: (418) 878-3001
-
1
-
2
-
3
-
4
-
5
-
6
PSG PF09010 is a multifunctional portable digital microscope with a 5-inch color LCD screen. It has a magnification range of 20x to 500x and a built-in 2-megapixel camera. It can be used for a wide variety of applications, including:
- PCB inspection: The high magnification and built-in camera make it ideal for inspecting printed circuit boards (PCBs) for defects.
- Soldering and rework: The microscope can be used to inspect solder joints and perform rework tasks.
- Quality control: The microscope can be used to inspect products for quality control purposes.
- Education and research: The microscope is a valuable tool for students and researchers in a variety of fields.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Broan 30042432A User manual
-
Broan B6EW Installation guide
-
-
Reznor RECB User manual
-
GOODMAN Amana MEC960603AN User manual
-
Rosemount 6888A O2 Combustion Flue Gas Transmitter Owner's manual
-
Revolv RE9X-12N4 Owner's Manual and Installation Instructions
-
Broan E4EB Series Electric Furnace Installation guide
-
-
