BCS Chipper / Shredder Assembly Instructions

Type
Assembly Instructions

BCS Chipper / Shredder is a versatile machine that can be used for a variety of tasks, including:

  • Chipping branches and limbs up to 3 inches in diameter
  • Shredding leaves, grass, and other organic materials
  • Creating mulch for your garden or flower beds
  • Clearing brush and debris from your property

The chipper/shredder is powered by a 13 HP Briggs & Stratton engine and features a large hopper that can accommodate large quantities of material. The chipper/shredder also comes with a variety of attachments, including a bagging system and a discharge chute, so you can customize the machine to meet your specific needs.

BCS Chipper / Shredder is a versatile machine that can be used for a variety of tasks, including:

  • Chipping branches and limbs up to 3 inches in diameter
  • Shredding leaves, grass, and other organic materials
  • Creating mulch for your garden or flower beds
  • Clearing brush and debris from your property

The chipper/shredder is powered by a 13 HP Briggs & Stratton engine and features a large hopper that can accommodate large quantities of material. The chipper/shredder also comes with a variety of attachments, including a bagging system and a discharge chute, so you can customize the machine to meet your specific needs.

BCS America, LLC
NOTES FOR ASSEMBLING BIO-100 CHIPPER/SHREDDER
IMPORTANT: Remember to lay out all the nuts and bolts and match them up with the holes
that need to be bolted together.
Fasten the top cover/shredder hopper and the chipper hopper at the same time, bolting on the
brace between the chipper hopper and the top cover.
Tighten all the hardware for both hoppers at roughly the same time and note that the M8 bolts
that hold on the top cover/shredder hopper are all the same with the exception of two longer
ones that fasten the brace for the chipper chute on to the top cover.
Install the front axle next. The axle can be put on upside down so make sure that the U shaped
edge of the axle cups around the front edge of the body of the chipper. It is held on by four
fasteners, with two being large studs protruding horizontally through the body of the unit and
going through two spacers, fastened by two washers and nuts. See photo:
After the front axle is on, tip the unit forward and install the two large blue mounting brackets
onto the body of the unit. Next put the two belts on the driven, (small) pulley set and thread
them onto the drive (large) pulley set. Now snug the four large cap screws that fasten the the
pulley set to the two large brackets and pry down on the pulley set to tighten up the bolts. See
photo:
Find a How-To video on Chipper/Shredder assembly at www.youtube.com/bcsamerica
or at www.bcsamerica.com/pages/how-to-videos/
Install the two round metal legs into the tubes on the Pulley housing and lock them in place with
the two set screws. Tip the unit rearward and install the two casters on the front axle and level
out the unit by adjusting the spacers on the casters and sliding the legs either up or down in the
tubes on the rear of the unit.
Make sure to attach the panic rope shut down rope on the unit.
A M E R I C A
Updated April 2019
Find a How-To video on Chipper/Shredder assembly at www.youtube.com/bcsamerica
or at www.bcsamerica.com/pages/how-to-videos/
  • Page 1 1
  • Page 2 2

BCS Chipper / Shredder Assembly Instructions

Type
Assembly Instructions

BCS Chipper / Shredder is a versatile machine that can be used for a variety of tasks, including:

  • Chipping branches and limbs up to 3 inches in diameter
  • Shredding leaves, grass, and other organic materials
  • Creating mulch for your garden or flower beds
  • Clearing brush and debris from your property

The chipper/shredder is powered by a 13 HP Briggs & Stratton engine and features a large hopper that can accommodate large quantities of material. The chipper/shredder also comes with a variety of attachments, including a bagging system and a discharge chute, so you can customize the machine to meet your specific needs.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI