Jenn-Air JXT8042ADS User manual

Brand: Jenn-Air

Model: JXT8042ADS

Type: User manual

This manual is also suitable for

RANGE HOOD

ModeJ Number', JX1-8030ADS

Manufaclurer Number: S99E30S

Size: 3t_"

m× 1-8036ADS [XT8042ADS

S99E36S S99E42S

36" 42"

GUIDE

TABLE OF CONTENTS

Satet'_ Instructions .................................................... 1

Controls 8; Features ............................................... 2-4

Maintenance ......................................................... 5-6

Warranty .................................................................. 7

Form No. A/04/03 Part No. US9900-0303A _2004 May_ag Apl_lian(::es Sales (o. litho U.S.A.

MODELS: JXT8030ADS JXT8036ADS JXT8042ADS

lostallation

Theinstallationin thismanuarisintendedforquarifiedinstallers,servicetechniciansor persons

withsimilarqualifiedbackground.DONOTattempttoinstarlthisapplianceyourserf,rniurycourd

resurtfrominstallingtheunitdueto rackofappropriateerectricalandtechnicalbackground.

Air erectricarwiring must be properly instarled, insulated and grounded. Overly accumulated

greasein old duct work should becleaned out or duct work should be replaced if necessary to

avoid the possibility of agrease fire. Checkall ioints on duct work to insure proper connection

andall ioints should be properly taped.

Operations

Readall instructions in this manual before operating the appliance. Save these instructions for

future reference.

Always leave safety grills and filters in place.Without these components, operating blowers

could catch on to hair,fingers and looseclothing.

NEVERdisposecigarette ashes, ignitable substances,orany foreign obiects into blowers.

NEVERleavecooking unattended.When frying, oil in the pan can easilyoverheat and catch fire.

The risk of self combustion is higher when the oil has been usedseveraltimes.

Cleaning

The saturation of greasy residue in the blower and filters may cause increased flammability.

Keepunit clean and free of greaseand residue build-up at all times to prevent possible fires.

Filters must be cleaned periodically and kept free from accumulation of cooking residue (see

cleaning instructions inside).Oldand worn filters must bereplaced immediately. Donot operate

blowers when filters are removed.Neverdisassembleparts toclean without properinstructions.

Disassemblyisrecommended to be performedby qualified personnelonly. Callourserviceceno

ter for removal instructions. 1-800-JENNAIR(1-800-536-6247)

The manufacturer declines all responsibility in the event of failure to observe the instrucz

tions given here for installation, maintenance and suitable use of the product. Themanufacz

turer further declines all responsibility for injury due to negligence and the warranty of the

unit automatically expires due to improper maintenance.

* Please check for latest specification revisions before any custom work or cutouts.

CONTROLS & FEATURES

TOUCHCONTROLS& FEATURES

O Blower OelOff

Disp!ay(Speedlevel,DelayOffhdicator,JilterClear,/Cba,,ge)

I ! I

Lights On/Off/Hold to Dim

Adjust 6 Speed Levems0 15 Min Delay Off

@ 81ewerOn/Off

Bypressing_), thebRowerisswitchedOnandOff.Whenswitchedon,theblowerstartsuponspeedmeveN3.

_l_ Speed Selection

The6speedmeveBsareselectedbypressing_) to decreaseand_ to increasespeedmeveLThedispmay

indicatesmevemseBected.

_} DemayOff

Thisis usedfor programmedshutdownof blowerand Hights15 minutesafter the functionis activated.

Press _) once,adotflashesin the Howerrighthandsideof disphy (_ indicatingthe function ison.

Thehoodwill compRetelyshut down in15 minutes.

_} Lights OntOff/Dim

SwitchmightsOnandOff bypressingkey (_) once. To dim lights,pressandhold(_) for 2 seconds.

Advance Display Funetians

Filter CleanReminder(Metal):

After every30 hoursofuse,the displaywill startflashingan _ remindingyoutocBeanthe metamfilters

for residueandpossibleclogs.

CONTROLS & FEATURES

CONTROLS:FILTERCHANGEiNDiCATOR(CARBONFILTERS)

Filter Change Reminder (Carbon, if fitted):

When your hood is installed as a 'Purifying' (Ductless Recimu[ating) unit, it is fitted with a set of

CarbonFHtersto purify exhaust and fumes from cooking, then re-circulate the air within the home=

These Carbon FHtersare required to be replaced after every120 hours of use=The Filter Change

Reminder function in the microprocessor needsto beswitched on=The microproci_ssorin the

controls when set, will elapse andcount usage time and indicate bya flashing _- when carbon

filter replacement is needed=

Setting the Filter Change Reminder:

When Off, hold _) forapprox=5 seconds.

The display will change from _}

(exhaust mode)to @, (purifying mode/

carbon filters used)this indicates that the

elapse timer function is switched on and

CarbonFilters are used.

FiJter Replace indicator:

When the display _ starts flashing, the

CarbonFilters require r' ep[acement

Re-setting Function:

Oncefilters are replaced, with hood off,

pressand hold _, the display will appear;

hold for approximately 5 seconds until

on display disappears 0 =The Filter

ChangeReminderis now re-set and anew

120 hours elapsecycle is initiated=

hdd 5 sees. display from <-o> to <C>

disp_> flashes

hdd 5 sees, display from <C> to < >

¢ @

CONTROLS & FEATURES

CONTROLS:FILTERCLEANINDICATOR(METALFILTERS)

Filter Clean Reminder (Standard [_letal Filters fitted)

Whether your hood is installed as an Exhaustor Purifying unit, a set of meta! filters are

fitted by the factory.TheseMeta! Filtersare intendedto filter out residuefrom cooking.

They need not bereplaced on a regular basis but are required to be keptdean. TheFj_r Change

Reminder function in the microprocessorwill automatically indicate bya flashing _,R_

when the metal filters need to be cbaned after every 30 hrs=of use.

Filterscan be cbaned byhand with non-abrasivesoapor in a dishwasher.Heavilysoibd

filters shouldalso be soaked in greasecutting detergent such as Formula'409' or its equivalent,

prior to cbaning=

Filter Clean Reminder:

When _ flashes on display,the metal

filters ins_lled are required to be cleaned.

This will occur after every30 hours of use.

display <A> flashes

Re-setting Function:

Resetthe FilterClean Remindertimer when

filters arecleaned and re-installed=Press

andhold _) for approx. 5seconds, the

display wil! appear; hold for approximately

5seconds until _ on display disappears

0 =The Filter Clean Reminderfunction

is now re-set and a new 30 hours elapse

cycle is initiated.

hold 5 eecs. display from <C> to < >

CLEANING

Surface I_laintenace:

Clean periodically with hot soapy water and clean cotton cloth=Donot use corrosive or abrasive

detergent (e=g=Cometpowder scrub, EZoOffoven cleaner),or steel wool/scouring pads which wi[[

scratch anddamage surface=

For heaviersoil use liquid degreaser such as"Formula 409" or "Fantastic" brandcleaner=

After cleaning, you may use non-abrasive stainless steel polish/cleaners such as3M or ZEP,to

polish and buff out the stainless luster andgrain. Always scrub lightly,with clean cotton cloth, and

with the grain. Do notuse any product containing chlorine bleach. Donot use "orange" cleaners.

Metal Filters

The Metal Filtersfitted by the factory are

intended to filter out residue and grease

from cooking.They need not be replacedon a

regular basisbut are requiredto be kept clean.

Filters should be cleanedafter every 30

hours of use. Usethe Filter Clean

Reminderfunction on the controls to

determine when filters require cleaning.

Removeand clean by handor in

dishwasher.Spray 'Formula 409' or

equivalent degreasingdetergent and leave

to soak if heavily so[N.

Dry filters and re-install before using hood.

Replacing Metal Filters

Should filters wear out due to age and

prolonged use, replacewith following part

number:

Hood Model: Part No, Filters in pkg.

JXTSO3OADS 49001002 2

JXTSO30ADS 49001001 3

JXTSO42ADS 49001001 3

Metal Filter Dimensions:

16.14 in x 9.17 inx 0.35 in

410 mmx 233 mm

Also replace any damaged filter that has

punctured or broken mesh, bentor brokenframe.

LIGHTS

Replacing Lightgulhs

Make sureaHpower is turned off and

burbsare cool

Removebyturning bqb counter

cbckwise.

rf burbsare difficurt to turn due to

probnged use, firmry attach a glass

suction cup approx,the diameter of the

burband turn. Usea rubber gripper or

rubber grovesto removeburb.

Repracementburbs areavailable at

specialty righting stores. Purchasetype

6U10 120V50W habgen burbs.

Orto order burbs,preasecall our service

center:1-80O-JENNAIR (1-800-536-6247}

Warranb]:

Full One Year Warranty =Parts and Labor

For one (1) year from the original retail pur-

chase date, any part which faib in normal

home use will be repairedor replacedfree of

charge.

Limited Warranty =Parts Only

Second Year = After the first year from the

original purchasedate, parts which fail in nor-

maLhome usewill be repairedor replacedfree

of charge for the part itself, with the owner

payingall other costs, including labor,mibage

andtransportation.

Canadian Residents

Theabovewarranties only coveran appliance

instaLbd in Canadathat has been certified or

listed by appropriatetest agencies for complio

anceto a National Standard of Canadaunless

the appliance was brought into Canadadue to

transfer of residencefrom the United Statesto

Canada.

Tbespecific warrantiesexpressedaboveam tl_e

ONLYwarrantiespmvio'edby tbe manufacturer

Tbesewarrantiesgiveyouspecificlegalrights,and

you may alsohaveotherrights wlTid7varyfrom

state,tostate,

What is Net Cevered By These Warranties:

1=Conditionsanddamages resulting from any of the following:

a. Improper installation, delivery,or maintenance.

b.Any repair,modification, alteration, or adiustment not authorized

bythe manufacturer or an authorized servicer.

c. Misuse,abuse,accidents, or unreasonableuse.

d. Incorrect ebctric current, voltage, or supply.

e. Improper setting of any control.

2.Warranties are void if the original serial numbers havebeen removed,

altered, or cannot be readilydetermined.

3=Light bulbs.

4.Productspurchasedforcommercialor industrialuse.

5.Thecostofserviceor servicecallto:

a.Correctinstallationerrors.

b.Instructtheuserontheproperuseoftheproduct,

c.Transporttheapplianceto theservicer:

6. Consequentialor incidental damages sustained by any personas a

result of any breachof these warranties. Some states do not allow the

exclusionor limitation of consequentialor incidental damages, sothe

aboveexclusion may notapply.

if YeuNeed Service

Callthe dealer from whom your appliance was purchased or call

Maytag ServicesaM,Jennair CustomerAssistance at 1-800-JENNAIR

(1-800-536-6247) USAand CANADAto locate an authorizedservicer.

Be sureto retain proof of purchase to verity warranty status. Referto

WARRANTYfor further information on owner's responsibilities for warranty

service.

If the dealer or service company cannot resolvethe problem, write to

Maytag ServicesaM,Attn:CAIR®Center,RO.Box2370, Cleveland,TN

37320-2370, or call I=800=JENNAJR(1-800-536-6247) USAandCANADA.

U.S.customersusingTTYfordeaf,hearingimpairedor speech

impaired,call1-800-688-2080.

NOTE: When writing or calling about a service problem, please include the

following information:

a.Yourname, addressand telephone number;

b. Model number and serial number;

c. Nameand address of your dealer or servicer;

d.A cleardescription of the problem you are having;

e. Proofof purchase(sales receipt)

User'sguides,service manuals and parts information are availablefrom

Maytag ServicesaM,Jennair CustomerAssistance.

Jenn-Air JXT8042ADS User manual

Brand: Jenn-Air

Model: JXT8042ADS

Type: User manual

This manual is also suitable for

Download PDF

report

Jenn-Air JXT8042ADS User manual

This manual is also suitable for

Jenn-Air JXT8042ADS User manual

Related papers

Other documents