Jenn-Air JXT8030ADS User manual

Type
User manual

This manual is also suitable for

RANGE HOOD
ModeJ Number', JX1-8030ADS
Manufaclurer Number: S99E30S
Size: 3t_"
m× 1-8036ADS [XT8042ADS
S99E36S S99E42S
36" 42"
GUIDE
TABLE OF CONTENTS
Satet'_ Instructions .................................................... 1
Controls 8; Features ............................................... 2-4
Maintenance ......................................................... 5-6
Warranty .................................................................. 7
Form No. A/04/03 Part No. US9900-0303A _2004 May_ag Apl_lian(::es Sales (o. litho U.S.A.
MODELS: JXT8030ADS JXT8036ADS JXT8042ADS
lostallation
Theinstallationin thismanuarisintendedforquarifiedinstallers,servicetechniciansor persons
withsimilarqualifiedbackground.DONOTattempttoinstarlthisapplianceyourserf,rniurycourd
resurtfrominstallingtheunitdueto rackofappropriateerectricalandtechnicalbackground.
Air erectricarwiring must be properly instarled, insulated and grounded. Overly accumulated
greasein old duct work should becleaned out or duct work should be replaced if necessary to
avoid the possibility of agrease fire. Checkall ioints on duct work to insure proper connection
andall ioints should be properly taped.
Operations
Readall instructions in this manual before operating the appliance. Save these instructions for
future reference.
Always leave safety grills and filters in place.Without these components, operating blowers
could catch on to hair,fingers and looseclothing.
NEVERdisposecigarette ashes, ignitable substances,orany foreign obiects into blowers.
NEVERleavecooking unattended.When frying, oil in the pan can easilyoverheat and catch fire.
The risk of self combustion is higher when the oil has been usedseveraltimes.
Cleaning
The saturation of greasy residue in the blower and filters may cause increased flammability.
Keepunit clean and free of greaseand residue build-up at all times to prevent possible fires.
Filters must be cleaned periodically and kept free from accumulation of cooking residue (see
cleaning instructions inside).Oldand worn filters must bereplaced immediately. Donot operate
blowers when filters are removed.Neverdisassembleparts toclean without properinstructions.
Disassemblyisrecommended to be performedby qualified personnelonly. Callourserviceceno
ter for removal instructions. 1-800-JENNAIR(1-800-536-6247)
The manufacturer declines all responsibility in the event of failure to observe the instrucz
tions given here for installation, maintenance and suitable use of the product. Themanufacz
turer further declines all responsibility for injury due to negligence and the warranty of the
unit automatically expires due to improper maintenance.
* Please check for latest specification revisions before any custom work or cutouts.
CONTROLS & FEATURES
TOUCHCONTROLS& FEATURES
O Blower OelOff
Disp!ay(Speedlevel,DelayOffhdicator,JilterClear,/Cba,,ge)
I ! I
Lights On/Off/Hold to Dim
Adjust 6 Speed Levems0 15 Min Delay Off
@ 81ewerOn/Off
Bypressing_), thebRowerisswitchedOnandOff.Whenswitchedon,theblowerstartsuponspeedmeveN3.
_l_ Speed Selection
The6speedmeveBsareselectedbypressing_) to decreaseand_ to increasespeedmeveLThedispmay
indicatesmevemseBected.
_} DemayOff
Thisis usedfor programmedshutdownof blowerand Hights15 minutesafter the functionis activated.
Press _) once,adotflashesin the Howerrighthandsideof disphy (_ indicatingthe function ison.
Thehoodwill compRetelyshut down in15 minutes.
_} Lights OntOff/Dim
SwitchmightsOnandOff bypressingkey (_) once. To dim lights,pressandhold(_) for 2 seconds.
Advance Display Funetians
Filter CleanReminder(Metal):
After every30 hoursofuse,the displaywill startflashingan _ remindingyoutocBeanthe metamfilters
for residueandpossibleclogs.
CONTROLS & FEATURES
CONTROLS:FILTERCHANGEiNDiCATOR(CARBONFILTERS)
Filter Change Reminder (Carbon, if fitted):
When your hood is installed as a 'Purifying' (Ductless Recimu[ating) unit, it is fitted with a set of
CarbonFHtersto purify exhaust and fumes from cooking, then re-circulate the air within the home=
These Carbon FHtersare required to be replaced after every120 hours of use=The Filter Change
Reminder function in the microprocessor needsto beswitched on=The microproci_ssorin the
controls when set, will elapse andcount usage time and indicate bya flashing _- when carbon
filter replacement is needed=
Setting the Filter Change Reminder:
When Off, hold _) forapprox=5 seconds.
The display will change from _}
(exhaust mode)to @, (purifying mode/
carbon filters used)this indicates that the
elapse timer function is switched on and
CarbonFilters are used.
FiJter Replace indicator:
When the display _ starts flashing, the
CarbonFilters require r' ep[acement
Re-setting Function:
Oncefilters are replaced, with hood off,
pressand hold _, the display will appear;
hold for approximately 5 seconds until
on display disappears 0 =The Filter
ChangeReminderis now re-set and anew
120 hours elapsecycle is initiated=
hdd 5 sees. display from <-o> to <C>
disp_> flashes
hdd 5 sees, display from <C> to < >
¢ @
CONTROLS & FEATURES
CONTROLS:FILTERCLEANINDICATOR(METALFILTERS)
Filter Clean Reminder (Standard [_letal Filters fitted)
Whether your hood is installed as an Exhaustor Purifying unit, a set of meta! filters are
fitted by the factory.TheseMeta! Filtersare intendedto filter out residuefrom cooking.
They need not bereplaced on a regular basis but are required to be keptdean. TheFj_r Change
Reminder function in the microprocessorwill automatically indicate bya flashing _,R_
when the metal filters need to be cbaned after every 30 hrs=of use.
Filterscan be cbaned byhand with non-abrasivesoapor in a dishwasher.Heavilysoibd
filters shouldalso be soaked in greasecutting detergent such as Formula'409' or its equivalent,
prior to cbaning=
Filter Clean Reminder:
When _ flashes on display,the metal
filters ins_lled are required to be cleaned.
This will occur after every30 hours of use.
display <A> flashes
Re-setting Function:
Resetthe FilterClean Remindertimer when
filters arecleaned and re-installed=Press
andhold _) for approx. 5seconds, the
display wil! appear; hold for approximately
5seconds until _ on display disappears
0 =The Filter Clean Reminderfunction
is now re-set and a new 30 hours elapse
cycle is initiated.
hold 5 eecs. display from <C> to < >
CLEANING
Surface I_laintenace:
Clean periodically with hot soapy water and clean cotton cloth=Donot use corrosive or abrasive
detergent (e=g=Cometpowder scrub, EZoOffoven cleaner),or steel wool/scouring pads which wi[[
scratch anddamage surface=
For heaviersoil use liquid degreaser such as"Formula 409" or "Fantastic" brandcleaner=
After cleaning, you may use non-abrasive stainless steel polish/cleaners such as3M or ZEP,to
polish and buff out the stainless luster andgrain. Always scrub lightly,with clean cotton cloth, and
with the grain. Do notuse any product containing chlorine bleach. Donot use "orange" cleaners.
Metal Filters
The Metal Filtersfitted by the factory are
intended to filter out residue and grease
from cooking.They need not be replacedon a
regular basisbut are requiredto be kept clean.
Filters should be cleanedafter every 30
hours of use. Usethe Filter Clean
Reminderfunction on the controls to
determine when filters require cleaning.
Removeand clean by handor in
dishwasher.Spray 'Formula 409' or
equivalent degreasingdetergent and leave
to soak if heavily so[N.
Dry filters and re-install before using hood.
Replacing Metal Filters
Should filters wear out due to age and
prolonged use, replacewith following part
number:
Hood Model: Part No, Filters in pkg.
JXTSO3OADS 49001002 2
JXTSO30ADS 49001001 3
JXTSO42ADS 49001001 3
Metal Filter Dimensions:
16.14 in x 9.17 inx 0.35 in
410 mmx 233 mm
Also replace any damaged filter that has
punctured or broken mesh, bentor brokenframe.
LIGHTS
Replacing Lightgulhs
Make sureaHpower is turned off and
burbsare cool
Removebyturning bqb counter
cbckwise.
rf burbsare difficurt to turn due to
probnged use, firmry attach a glass
suction cup approx,the diameter of the
burband turn. Usea rubber gripper or
rubber grovesto removeburb.
Repracementburbs areavailable at
specialty righting stores. Purchasetype
6U10 120V50W habgen burbs.
Orto order burbs,preasecall our service
center:1-80O-JENNAIR (1-800-536-6247}
Warranb]:
Full One Year Warranty =Parts and Labor
For one (1) year from the original retail pur-
chase date, any part which faib in normal
home use will be repairedor replacedfree of
charge.
Limited Warranty =Parts Only
Second Year = After the first year from the
original purchasedate, parts which fail in nor-
maLhome usewill be repairedor replacedfree
of charge for the part itself, with the owner
payingall other costs, including labor,mibage
andtransportation.
Canadian Residents
Theabovewarranties only coveran appliance
instaLbd in Canadathat has been certified or
listed by appropriatetest agencies for complio
anceto a National Standard of Canadaunless
the appliance was brought into Canadadue to
transfer of residencefrom the United Statesto
Canada.
Tbespecific warrantiesexpressedaboveam tl_e
ONLYwarrantiespmvio'edby tbe manufacturer
Tbesewarrantiesgiveyouspecificlegalrights,and
you may alsohaveotherrights wlTid7varyfrom
state,tostate,
What is Net Cevered By These Warranties:
1=Conditionsanddamages resulting from any of the following:
a. Improper installation, delivery,or maintenance.
b.Any repair,modification, alteration, or adiustment not authorized
bythe manufacturer or an authorized servicer.
c. Misuse,abuse,accidents, or unreasonableuse.
d. Incorrect ebctric current, voltage, or supply.
e. Improper setting of any control.
2.Warranties are void if the original serial numbers havebeen removed,
altered, or cannot be readilydetermined.
3=Light bulbs.
4.Productspurchasedforcommercialor industrialuse.
5.Thecostofserviceor servicecallto:
a.Correctinstallationerrors.
b.Instructtheuserontheproperuseoftheproduct,
c.Transporttheapplianceto theservicer:
6. Consequentialor incidental damages sustained by any personas a
result of any breachof these warranties. Some states do not allow the
exclusionor limitation of consequentialor incidental damages, sothe
aboveexclusion may notapply.
if YeuNeed Service
Callthe dealer from whom your appliance was purchased or call
Maytag ServicesaM,Jennair CustomerAssistance at 1-800-JENNAIR
(1-800-536-6247) USAand CANADAto locate an authorizedservicer.
Be sureto retain proof of purchase to verity warranty status. Referto
WARRANTYfor further information on owner's responsibilities for warranty
service.
If the dealer or service company cannot resolvethe problem, write to
Maytag ServicesaM,Attn:CAIR®Center,RO.Box2370, Cleveland,TN
37320-2370, or call I=800=JENNAJR(1-800-536-6247) USAandCANADA.
U.S.customersusingTTYfordeaf,hearingimpairedor speech
impaired,call1-800-688-2080.
NOTE: When writing or calling about a service problem, please include the
following information:
a.Yourname, addressand telephone number;
b. Model number and serial number;
c. Nameand address of your dealer or servicer;
d.A cleardescription of the problem you are having;
e. Proofof purchase(sales receipt)
User'sguides,service manuals and parts information are availablefrom
Maytag ServicesaM,Jennair CustomerAssistance.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Jenn-Air JXT8030ADS User manual

Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI